Microchip Technology

MCP3422A3-E/MC - 18-Bit Dual-Channel Delta-Sigma ADC | Microchip

MPN: MCP3422A3-E/MC ✓ Aktif
2.048 V Vdss 8-pin DFN (2 mm x 3 mm) Package
MOQ: 1 |

MCP3422A3-E/MC Ringkasan

The Microchip Technology MCP3422A3-E/MC is an 18-bit, two-channel delta-sigma analog-to-digital converter with differential inputs and an I2C interface, housed in an 8-pin DFN package measuring 2 mm by 3 mm. Its on-board precision reference is 2.048 V, establishing a differential input range of plus or minus 2.048 V, while the device operates from a 2.7 V to 5.5 V supply. These characteristics position it as a compact, high-resolution converter for low-frequency measurement systems.

An analog-to-digital converter, or ADC, converts continuous analog voltages into numeric values that a microcontroller or embedded system can process. The MCP3422 belongs to the delta-sigma ADC family, where an internal modulator and digital filter shape the conversion result with high resolution and good noise performance at relatively low sample rates. This two-channel device supports differential measurement, which helps reject common-mode noise when a sensor output is referenced to a nearby analog ground.

The MCP3422 family provides up to 18 bits of resolution and integrates a 2.048 V precision reference. Differential input capability and the internal reference reduce the need for external active balancing networks. The I2C interface also reduces the number of signal connections required between the converter and a host controller. Compared with general-purpose flash-based ADCs, the architecture is better suited to instrumentation, industrial monitoring, and slowly changing sensor signals rather than high-speed waveform capture.

The A3 designation identifies the speed grade within the MCP3422 family. The related MCP3422A3T-E/MS listing identifies this performance level as approximately 3.75 samples per second, making the A3 version appropriate for temperature, pressure, load-cell, and process-control measurements where low conversion throughput is acceptable. Differential measurements can also use the device's programmable gain behavior when the signal amplitude requires additional sensitivity.

Typical applications include bridge-based pressure and load measurements, current-shunt monitoring, precision temperature sensing, laboratory instrumentation, and factory automation. The 2 mm by 3 mm DFN package supports compact analog front ends, but the small thermal pad and exposed package structure require careful PCB layout and solder assembly. The 2.7 V to 5.5 V operating range also allows the converter to share supply arrangements with both 3.3 V and 5 V embedded systems.

When laying out this device, place input filtering and reference-decoupling components close to their associated pins, route the exposed pad into a thermal and ground plane, and keep digital I2C traces away from high-impedance differential inputs. Confirm the selected conversion speed against the required latency and noise trade-off, and use the manufacturer pin-description table when assigning PCB tracks and test points.

This page combines device specifications, package details, application guidance, design notes, and a structured comparison with related MCP3422 devices. It also highlights the differences between gain grades and package options so engineers can identify a compatible replacement without confusing an 8-pin DFN part with an MSOP or SOIC variant.

Pilihan pengganti yang segera untuk MCP3422A3-E/MC — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera MCP3422A3-E/MC (sama faktor bentuk dan kaki) — berbeza dalam Package, Digital Interface, Differential Input Range, Input Architecture, Automotive Qualification.

Microchip Technology
Package: 8-pin DFN with exposed pad, 2 x 3 mm
Digital Interface: I2C
Differential Input Range: ±2.048 V
Microchip Technology
Package: 8-DFN, 2 x 3 mm
Digital Interface: 2-wire I2C
Differential Input Range: ±2.048 V
Microchip Technology
Package: 8-VFDFN exposed pad, 2 mm x 3 mm
Differential Input Range: Plus or minus 2.048 V
Input Architecture: Differential inputs
Microchip Technology
Package: 8-pin SOIC
Digital Interface: 2-wire I²C-compatible serial interface
Differential Input Range: ±2.048 V
Microchip Technology
Package: 8-DFN, 2 x 3 mm
Digital Interface: I2C, 2-wire
Differential Input Range: ±2.048 V

MCP3422A0-E/MC

✅ Masuk Drop-In
Microchip Technology
📦 8-DFN (2x3)
18 bit · 2 differential inputs · Sigma-delta · 1 · 3.75 samples per second · 4 samples per second · 2.048 V · ±2.048 V

Hubungi untuk harga

Lihat Datasheet →

MCP3422A2-E/MC

✅ Masuk Drop-In
Microchip Technology
📦 8-DFN (2x3)
Delta-sigma ADC · 18 bit · 2 differential channels · Differential inputs · 2.7 V to 5.5 V · 2.048 V · Plus or minus 2.048 V · 240 samples per second

Hubungi untuk harga

Lihat Datasheet →

MCP3422A6-E/MC

✅ Masuk Drop-In
Microchip Technology
📦 8-DFN (2x3)
Up to 18 bits · 2 channels · Differential inputs · Delta-sigma ADC · 240 SPS · 2.048 V · ±2.048 V · 4.096 V

Hubungi untuk harga

Lihat Datasheet →

MCP3422A3-E/SN

✅ Masuk Drop-In
Microchip Technology
📦 8-DFN (2x3)
18 bit · 2 channels · Differential input · 1 sigma-delta converter · 3.75 samples/s · 2.048 V · ±2.048 V · 2.7 V to 5 V

Hubungi untuk harga

Lihat Datasheet →

MCP3422A3-E/MC Penilaian maksimum & Ciri-ciri Elektrik

ADC Type Delta-sigma ADC
Pemecahkatan 18 bits
Number of Channels 2 channels
Input Type Differential
Antaramuka I2C
Internal Reference Voltage 2.048 V
Differential Input Range -2.048 V to +2.048 V
Supply Voltage Range 2.7 V to 5.5 V
Gambaran Suhu Operasi -40 °C to +125 °C
Kemasan 8-pin DFN (2 mm x 3 mm)
Jenis Pemasangan Surface mount
A3 Conversion Rate 3.75 samples per second
On-Board Reference Yes, 2.048 V precision reference
Automotive Qualification AEC-Q100 grade indicated for the A3 family

Panduan Konfigurasi Pin MCP3422A3-E/MC 8-pin dfn (2 mm x 3 mm)

Konfigurasi pin untuk MCP3422A3-E/MC (8-pin dfn (2 mm x 3 mm) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-pin dfn (2 mm x 3 mm) untuk MCP3422A3-E/MC

Tiada data garisan pin yang diperoleh untuk MCP3422A3-E/MC.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MCP3422A3-E/MC patut untuk 6 aplikasis: Load-Cell and Weighing Systems, Precision Pressure and Process Monitoring, RTD and Temperature Acquisition, Battery and Power-System Monitoring, Laboratory and Instrumentation, Environmental and IoT Sensing Nodes.

⚖️

Load-Cell and Weighing Systems

The MCP3422A3-E/MC is suitable for resistive-bridge sensors whose output changes relatively slowly, such as platform load cells, force transducers, and industrial weighing modules. Its two differential input channels can acquire complementary bridge signals, helping reject common-mode voltage and reducing the effect of ground offsets in long cable runs. The 18-bit resolution preserves small changes around a mechanical zero point, while the integrated 2.048 V reference provides a stable conversion baseline. The approximately 3.75 samples-per-second A3 rate suits static load, slow ramp, and vibration-envelope measurements. In a practical instrument, connect the bridge output through RC filtering and differential input routing, then compensate in firmware for bridge imbalance and temperature drift.

🏭

Precision Pressure and Process Monitoring

The MCP3422A3-E/MC fits pressure transmitters, differential pressure cells, and industrial process-monitoring loops where a millivolt-level sensor signal must be digitized reliably. Differential inputs support measurement of a sensor bridge or the difference between two related voltages, reducing sensitivity to common-mode noise generated by adjacent switching circuits. The converter's 18-bit resolution supports fine process-control measurements, and its integrated 2.048 V reference removes the need for a separate reference buffer on space-constrained boards. At approximately 3.75 samples per second, it is appropriate for temperature, pressure, and flow loops that change over seconds rather than milliseconds. Keep analog traces short, use a dedicated analog ground region, and decouple the supply close to the device to maintain predictable conversion accuracy.

🌡️

RTD and Temperature Acquisition

The MCP3422A3-E/MC can acquire temperature information from resistive sensors in industrial equipment, ovens, cold-chain monitoring, and thermal controllers. Its two differential channels allow one converter to handle a pair of RTD inputs, while the high nominal resolution helps preserve small temperature-related resistance changes without requiring a high-speed ADC. The integrated 2.048 V reference provides the excitation and conversion baseline for a ratiometric bridge-style measurement, and the A3 conversion rate is more than adequate for slow thermal processes. For stable readings, connect the RTD through a matched bridge and differential filters, isolate analog routing from digital clocks, and apply software linearization and ambient compensation. The compact 2 mm by 3 mm DFN package also helps when the acquisition board must fit beside the sensor connector.

🔋

Battery and Power-System Monitoring

The MCP3422A3-E/MC is appropriate for supervisory circuits that measure battery voltage, charger status, or the voltage across a current shunt. Two differential channels can support redundant or sequential power-rail measurements, while the 2.7 V to 5.5 V supply range permits operation in low-energy embedded systems. Its 18-bit resolution can represent small changes in a slowly varying rail or shunt voltage, and the integrated reference supports stable ratiometric measurements without an external precision reference. The A3 grade's approximately 3.75 samples-per-second rate is well matched to energy-management loops. In a battery design, apply the appropriate input protection, account for the ADC input range, and keep the analog divider or shunt node away from high-current switching paths to prevent conversion errors.

🔬

Laboratory and Instrumentation

The MCP3422A3-E/MC is useful in compact laboratory instruments that require more resolution than a basic microcontroller ADC but do not require waveform-acquisition rates. It can digitize a calibrated sensor output, potentiometer position, or differential measurement produced by an analog front end. The internal 2.048 V reference and differential inputs help simplify calibration and improve immunity to shared ground disturbances, while I2C keeps the connection to an instrument controller compact. The A3 grade provides approximately 3.75 conversions per second, making it suitable for panel meters, laboratory loggers, and calibration fixtures. Preserve measurement accuracy by using a quiet analog supply, separating analog and return currents, validating the gain configuration in firmware, and recording calibration coefficients against the manufacturer's recommended reference conditions.

🧩

Environmental and IoT Sensing Nodes

The MCP3422A3-E/MC suits compact environmental monitors that combine a resistive or ratiometric sensor with an embedded I2C controller. Its two differential channels can read humidity, gas, soil-moisture, or light-sensor interfaces while the small 2 mm by 3 mm DFN package preserves board area. The 18-bit resolution improves the visibility of small sensor changes, and the integrated reference reduces the component count of the measurement chain. The approximately 3.75 samples-per-second conversion rate is suitable for periodic environmental sampling rather than continuous high-speed capture. Low-power designs should disable conversions between samples, use the device's low-noise analog architecture, and isolate sensitive sensor nodes from radio and DC-DC converter sections. Firmware should also reject outliers and compensate for sensor warm-up and temperature drift.

What is the MCP3422A3-E/MC?
The MCP3422A3-E/MC is a Microchip Technology 18-bit, two-channel delta-sigma ADC with differential inputs, an I2C interface, and an integrated 2.048 V reference. It is packaged in an 8-pin DFN measuring 2 mm by 3 mm. According to the Microchip MCP3422 product page, the family supports a differential input range of plus or minus 2.048 V and is intended for low-noise, high-accuracy measurement systems.
What is the voltage range of the MCP3422A3-E/MC?
The MCP3422A3-E/MC operates from 2.7 V to 5.5 V and accepts differential inputs from -2.048 V to +2.048 V when its internal 2.048 V reference is used. The FindIC comparison data identifies the same 2.7 V minimum and 5.5 V maximum supply limits. This makes the converter usable in 3.3 V and 5 V systems, subject to the absolute maximum ratings in the manufacturer datasheet.
Where can I download the MCP3422A3-E/MC datasheet PDF?
The official MCP3422 product page at Microchip Technology provides the manufacturer documentation, including the MCP3422 datasheet PDF. The Datasheet section of that page is the preferred source because it reflects the latest manufacturer revision. Use the device-specific MCP3422 documentation for pin descriptions, electrical characteristics, gain settings, timing, and the recommended application circuit before laying out the PCB.
Where can I find the MCP3422A3-E/MC pinout?
The MCP3422A3-E/MC pinout is published in the pin-description section of the Microchip MCP3422 datasheet. The device uses an 8-pin DFN footprint with VDD, ground, I2C, reference, and differential analog-input connections. Use the manufacturer diagram for the exact numbering and exposed-pad treatment, and verify each net against the package drawing before routing because the DFN land pattern is physically smaller than the MSOP and SOIC options.
What are the key specifications of MCP3422A3-E/MC?
The MCP3422A3-E/MC provides 18-bit resolution, two differential input channels, an I2C interface, a 2.048 V internal reference, a 2.7 V to 5.5 V supply range, and operation from -40 °C to +125 °C. It is available in an 8-pin DFN package measuring 2 mm by 3 mm. The A3 grade is associated with approximately 3.75 samples per second, making it suitable for slow sensor measurements rather than waveform capture.
Is MCP3422A3-E/MC the same as MCP3422A0-E/MC?
No. Both devices are Microchip Technology 18-bit, two-channel MCP3422-family converters in the 8-pin DFN package, but the A0 and A3 suffixes identify different performance grades. The A3 grade offers the higher conversion-rate option, approximately 3.75 samples per second, while the A0 grade is the lower-speed option. Both can share the same PCB footprint, but firmware timing and acquisition-rate requirements must match the selected grade.
When should I choose MCP3422A3-E/MC over MCP3422A0-E/MC?
Choose MCP3422A3-E/MC when the application needs a higher acquisition rate than the A0 grade and can tolerate the additional conversion activity associated with that operating point. The A3 version provides approximately 3.75 samples per second, making it preferable for faster process-control or monitoring loops. Choose MCP3422A0-E/MC when the lowest conversion rate is sufficient and lower operating activity is preferred.
What is the best drop-in replacement for MCP3422A3-E/MC?
The closest same-package alternatives are the Microchip MCP3422A0-E/MC, MCP3422A2-E/MC, MCP3422A6-E/MC, and MCP3422A3-E/SN, subject to confirming package dimensions, pinout, gain settings, and acquisition timing. The A2 and A6 parts change conversion performance rather than the electrical interface. Because the verified comparison results do not identify a verified cross-manufacturer pin-compatible equivalent, an unverified competitor part should not be treated as a direct drop-in replacement.
Can MCP3422A0-E/MC replace MCP3422A3-E/MC?
The MCP3422A0-E/MC can serve as a board-level alternative because it uses the same 8-pin DFN format and implements the same MCP3422 18-bit, two-channel I2C architecture. Its conversion-rate grade is lower, so it is only appropriate when the original design's sampling latency and data-acquisition assumptions remain acceptable. Review the gain, timing, and register settings before committing the substitution.
Is there an equivalent MCP3422A3-E/MC from another manufacturer?
No verified cross-manufacturer pin-compatible equivalent is established for the MCP3422A3-E/MC. A substitute would need to match the 8-pin DFN land pattern, differential input arrangement, 2.048 V reference behavior, I2C address and register protocol, gain options, and acquisition timing. The available comparison results identify related Microchip devices but do not document a qualified competitor drop-in, so the safest replacement path is within the MCP3422 family.
How fast does the MCP3422A3-E/MC convert analog signals?
The MCP3422A3-E/MC operates at approximately 3.75 samples per second in the A3 performance grade. The associated MCP3422A3T-E/MS listing identifies the same A3 speed level as 3.75 samples per second. This rate is suitable for temperature, pressure, load, and chemical-sensor monitoring where the measured value changes more slowly than the conversion interval.
What applications are suitable for MCP3422A3-E/MC?
The MCP3422A3-E/MC fits slow, precision-oriented measurements such as load cells, pressure bridges, temperature probes, current shunts, and industrial process sensors. Differential inputs help reject common-mode disturbance, while the integrated 2.048 V reference simplifies the analog front end. Its 2 mm by 3 mm DFN package also supports space-constrained instrumentation, although careful thermal-pad and signal-routing design is required.
What is the difference between MCP3422A2-E/MC and MCP3422A3-E/MC?
The MCP3422A2-E/MC and MCP3422A3-E/MC share the Microchip MCP3422 architecture, 18-bit resolution, two differential channels, I2C interface, and 8-pin DFN package. Their principal difference is the A-series speed grade: A3 is the approximately 3.75 samples-per-second option, while A2 represents the lower conversion-rate grade. Both can be considered for the same footprint, provided the firmware timing matches the selected grade.
How should the MCP3422A3-E/MC be placed on a PCB?
Place the MCP3422A3-E/MC close to the analog source and connect the exposed pad to the recommended ground and thermal structure. Keep I2C routing away from the differential inputs, locate input-filter components near the relevant pins, and follow the package drawing for land-pattern dimensions. The 2 mm by 3 mm DFN also requires assembly-process control because its lead pitch and exposed thermal area are smaller than those of MSOP options.
Where to buy MCP3422A3-E/MC online?
Use the Request a Quote form on this page to ask for MCP3422A3-E/MC pricing, stock confirmation, and a current lead time for the 8-pin DFN package. Because the distributor listings do not expose explicit quantity-break prices in the captured product details, request an order quotation that states the required quantity, packaging preference, and delivery location. A current quotation is more reliable than an archived catalog amount.
What is the price and lead time of MCP3422A3-E/MC?
Current MCP3422A3-E/MC pricing and lead time are available through the Request a Quote form on this page. Submit the required quantity, packaging option, destination country, and target production date for a quotation. The form is the appropriate channel for confirmed commercial terms because distributor inventory, volume breaks, and lead times can change independently of the device's technical specifications.

Data referensi kejuruteraan untuk MCP3422A3-E/MC — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the MCP3422A3-E/MC when you need an 18-bit, two-channel delta-sigma ADC with differential inputs, I2C connectivity, an integrated 2.048 V reference, and an approximately 3.75 samples-per-second acquisition rate in a compact 2 mm by 3 mm DFN package. It is a strong fit for load cells, RTDs, pressure sensors, current shunts, and environmental monitors whose signals change more slowly than the conversion interval.

Use MCP3422A0-E/MC when the lower conversion grade is sufficient and lower operating activity is preferable. Use MCP3422A2-E/MC when the design needs the same footprint and interface but can accept the A2 timing profile. Choose MCP3422A6-E/MC when faster acquisition is more valuable than retaining the A3 speed grade. For MCP3422A3T-E/MS, confirm the package before substitution because MSOP and DFN require different PCB land patterns. No verified cross-manufacturer drop-in equivalent was established; changing vendors requires a new pinout, timing, gain, noise, and firmware review rather than a footprint-only substitution.

Perbandingan dengan Gantian

Parametr Produk Ini MCP3422A0-E/MC MCP3422A2-E/MC MCP3422A6-E/MC MCP3422A3-E/SN
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3) 8-DFN (2x3)
Resolution 18 bits 18 bits 18 bits 18 bits 18 bits
Number of Channels 2 channels 2 channels 2 channels 2 channels 2 channels
Input Configuration Differential Differential Differential Differential Differential
Internal Reference 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Conversion Performance Grade A3, approximately 3.75 samples/s A0 lower-speed grade A2 lower-speed grade A6 higher-speed grade A3, approximately 3.75 samples/s
Interface I2C I2C I2C I2C I2C
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C

Penyeberangsung Jelas

  • Balanced conversion speed and high resolution for low-frequency instrumentation (vsMCP3422A0-E/MC)
  • Compact 2 mm by 3 mm implementation without sacrificing differential measurement (vsMCP3422A3T-E/MS)
  • Integrated reference reduces external analog component count (vsMCP3422A6-E/MC)
  • Exact A3 performance alternative for design continuity (vsMCP3422A2-E/MC)

Catatan Desain

Keep the two differential analog inputs symmetrical and route them away from the I2C clock and data lines. Place input RC filters close to the converter pins, with the resistor nearer the ADC than the capacitor, so injected noise is attenuated before reaching the input. For a bridge sensor, route the two channels as a closely matched pair to reduce conversion of common-mode noise into differential error.

Decouple the supply at the device with the capacitance recommended by the manufacturer datasheet and keep the connection to the package pin short. If a shared DC-DC converter supplies the analog section, place the analog decoupling before the sensitive sensor connections and keep high-current switching loops on the opposite side of the board. Verify the 2.7 V to 5.5 V operating range at the ADC pins under worst-case supply ripple and load conditions.

Estimated: at a 3.3 V supply, 5.5 V analog input, and 2 mA average device current, the rough converter input-path power is 11 mW; actual device dissipation depends on internal architecture and operating mode and must be confirmed from the datasheet. Because the DFN is only 2 mm by 3 mm, provide the manufacturer-recommended exposed-pad copper area and consider thermal coupling to surrounding components when the board operates at elevated ambient temperature.

Do not substitute the MCP3422A3T-E/MS into an -E/MC board without checking the footprint; the latter uses an 8-MSOP package rather than the 8-pin DFN. Likewise, changing among A0, A2, A3, and A6 grades can alter conversion latency, noise behavior, and valid operating modes. Review the gain table, sample timing, acquisition timing, and digital-filter settling requirements in firmware after any substitution.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The related MCP3422A3T-E/MS distributor listing identifies the A3 family as automotive AEC-Q100 grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact -E/MC ordering code should be confirmed on the manufacturer product page.

Data disahkan pada: 2026-11-20 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MCP3422A3-E/MC datasheet MCP3422A3-E/MC pinout MCP3422A3-E/MC specifications MCP3422A3-E/MC equivalent MCP3422A3-E/MC replacement MCP3422A3-E/MC vs MCP3422A0-E/MC MCP3422A3-E/MC price MCP3422A3-E/MC stock Microchip MCP3422A3-E/MC MCP3422 18 bit differential ADC MCP3422 8 DFN pinout MCP3422 load cell application MCP3422 2.048V reference MCP3422 I2C ADC footprint

Komponen dan Tanda berkaitan

Microchip Technology MCP3422A3-E/MC MCP3422 MCP3422A0-E/MC MCP3422A2-E/MC MCP3422A6-E/MC MCP3422A3-E/SN MCP3422A3T-E/MS analog-to-digital converter ADC delta-sigma ADC I2C differential input 18-bit resolution 2.048 V precision reference 8-pin DFN 2 mm by 3 mm package surface-mount package load-cell measurement RTD temperature sensing pressure bridge current-shunt monitoring AEC-Q100 RoHS
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ