MPC565CVR40 - 40MHz PowerPC MCU 1MB Flash | NXP | 388-PBGA
MPN: MPC565CVR40 ✗ انتهى عمره الإنتاجيMPC565CVR40 نظرة عامة
A microcontroller (MCU) is a compact embedded processor that integrates a CPU core, program memory, data RAM, and a rich set of peripherals into a single semiconductor die. Power Architecture (PowerPC) MCUs extend this with a 32-bit RISC instruction set, hardware multiply-accumulate, and deterministic interrupt latency, occupying the tier between 8/16-bit microcontrollers and full application processors. The MPC56x family specifically targets automotive powertrain and chassis control, with the MPC565 representing one of the early production-grade members.
Key features include 1 MB embedded Flash with shadow block for fail-safe firmware updates, 36 KB SRAM for stack/heap and data buffers, 56 digital I/O pins supporting GPIO and peripheral functions, and a flexible external oscillator input. The 388-BGA package provides high pin density required by automotive ECU designs, while retaining compatibility with NXP's CodeWarrior and Green Hills MULTI toolchains.
Architecturally, the MPC565 pairs the PowerPC e500 core block with a unified 32-bit peripheral bus, TPU (Time Processing Unit) for complex I/O timing, and a QADC (Queued Analog-to-Digital Converter) block. The result is a single-chip ECU platform that historically powered engine management units where deterministic real-time response and on-chip flash were decisive design factors.
Typical applications include automotive engine control units (ECU), transmission control modules (TCM), electronic stability control (ESC), industrial servo drives, and high-end CAN/LIN gateway modules. The wide I/O count and dual-supply (2.6 V core / 5 V I/O) make it especially suitable for mixed-signal automotive nodes.
When designing with the MPC565CVR40, ensure the 388-BGA land pattern matches the 27x27 mm mechanical outline exactly; footprints from earlier MPC5xx variants are not guaranteed pin-compatible. Decoupling requires at least eight 100 nF ceramics placed adjacent to the BGA perimeter, and the 2.6 V core rail must rise monotonically before the 5 V I/O rail to avoid latch-up.
This page synthesizes distributor pricing, pin-compatible alternatives within the MPC56x/Qorivva family, and practical design notes that extend beyond the manufacturer datasheet summary to accelerate engineering decisions for legacy and current production programs.
بدائل مباشرة لـ MPC565CVR40 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MPC565CVR40 (نفس عامل الشكل والبصمة) — يختلف في Core Architecture, Operating Temperature, Peripherals, Supply Voltage, Mounting Type.
MPC565CVR40R2
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MPC565CZP40
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MPC563MZP56R2
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MPC563MZP56
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MPC535CZP40
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MPC565CVR40 الحدود القصوى والخصائص الكهربائية
| Core Architecture | PowerPC e500 (32-bit RISC) |
| Series | MPC5xx / MPC56x (Qorivva) |
| أقصى تردد للساعة | 40 MHz |
| Program Memory Size | 1 MB (1M x 8) Flash |
| RAM Size | 36 KB |
| Number of I/O | 56 |
| جهد التغذية | 2.6 V / 5 V |
| العلبة / الحالة | 388-PBGA (27 x 27 mm) |
| Oscillator Type | External |
| Program Memory Type | FLASH |
| نوع التركيب | Surface Mount |
| Packaging | Tray |
| Peripherals | TPU, QADC, CAN, SPI, SCI |
| درجة حرارة التشغيل | -40C to +85C (typical automotive) |
دليل تكوين أطراف MPC565CVR40 388-pbga (27 x 27 mm)
تكوين الأطراف لـ MPC565CVR40 (حزمة 388-pbga (27 x 27 mm)). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MPC565CVR40.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MPC565CVR40 مناسب لـ 6 التطبيقs: Automotive Engine Control Unit (ECU), Transmission Control Module (TCM), Electronic Stability Control (ESC), Industrial Servo Drive Controller, CAN/LIN Gateway Module, Body Control Module with Mixed-Signal I/O.
Automotive Engine Control Unit (ECU)
The MPC565CVR40's 40 MHz PowerPC core and 1 MB on-chip Flash historically powered production engine management ECUs where deterministic interrupt latency and fail-safe firmware updates were mandatory. Its dual 2.6 V core / 5 V I/O supply matches the analog sensor conditioning sections typical of powertrain designs, and the integrated QADC block handles injector and crank position sampling without external ADCs. Compared to 16-bit microcontrollers in the same era, the 32-bit e500 core enabled closed-loop idle speed and torque-based engine control with adequate MIPS headroom.
موصى به
Transmission Control Module (TCM)
Transmission control modules leverage the MPC565CVR40's TPU (Time Processing Unit) for precise solenoid actuation timing and its QADC for line-pressure feedback. The 388-BGA package supports the large number of I/O required to drive multiple shift solenoids, pressure regulators, and speed sensors. The 1 MB Flash holds shift calibration maps that vary by vehicle platform, while the 36 KB SRAM keeps buffer for real-time torque management algorithms.
موصى به
Electronic Stability Control (ESC)
ESC systems require deterministic sub-millisecond response to wheel-speed sensors and yaw-rate inputs, which is exactly what the MPC565CVR40's PowerPC core and TPU provide. The 388-BGA footprint accommodates the brake-by-wire interface signals, and the on-chip CAN controllers integrate seamlessly with chassis network buses. Designers chose the MPC565 for its real-time interrupt performance and automotive-grade qualification against AEC-Q100-like environmental stress tests.
موصى به
Industrial Servo Drive Controller
Beyond automotive, the MPC565CVR40 served industrial servo drives that needed 32-bit performance, deterministic PWM generation via the TPU, and integrated QADC for current feedback loops. The 388-BGA supports the encoder interfaces and gate-driver signals required for three-phase IGBT/MOSFET power stages, and the 5 V I/O tolerance interfaces directly to legacy industrial logic. Although newer Cortex-M parts now dominate this space, many installed servo drives still run on MPC56x silicon.
موصى به
CAN/LIN Gateway Module
A CAN/LIN gateway aggregates multiple vehicle bus segments and routes messages between them, which is well-matched to the MPC565CVR40's dual CAN controllers and ample GPIO for LIN master implementations. The 1 MB Flash holds gateway routing tables and diagnostic firmware, while the 40 MHz core handles message filtering without bottlenecks. The 388-BGA package exposes all the bus pins on a single die footprint suitable for high-density PCB layouts.
موصى به
Body Control Module with Mixed-Signal I/O
Body control modules integrate lighting, wiper, and accessory drivers; the MPC565CVR40's 56 GPIO plus QADC simplify the front-end of mixed-signal body electronics. Designers used the 5 V I/O tolerance to directly drive relay coils and LED strings, while the 2.6 V core kept power consumption modest. Although newer Qorivva parts now serve this segment, MPC565 remains a qualified platform for long-life automotive body programs.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MPC565CVR40 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MPC565CVR40R2 | MPC565CZP40 | MPC563MZP56R2 | MPC563MZP56 | MPC535CZP40 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 388-PBGA (27x27) | 388-PBGA (27x27) - same | 388-PBGA (27x27) - same | 388-PBGA (27x27) - same | 388-PBGA (27x27) - same | 388-PBGA (27x27) - same |
| Maximum Clock Frequency | 40 MHz | 40 MHz | 40 MHz | 56 MHz | 56 MHz | 40 MHz |
| Core Architecture | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC |
| Operating Voltage | 2.6 V / 5 V | 2.6 V / 5 V | 2.6 V / 5 V | 2.6 V / 5 V | 2.6 V / 5 V | 2.6 V / 5 V |
| Lifecycle Status | NRND | NRND | NRND | Obsolete (estimate) | Obsolete (estimate) | Obsolete (estimate) |
أبرز الفروقات
- Largest on-chip Flash in the early MPC56x generation (مقابلMPC535CZP40)
- Production-proven PowerPC e500 core with automotive pedigree (مقابلMPC563MZP56R2)
- 388-PBGA package supports the highest I/O count in the family (مقابلMPC563 family in QFP)
ملاحظات التصميم
The MPC565CVR40 requires two supply rails: 2.6 V for the internal core and 5 V for the I/O ring. According to NXP's power-sequencing guidance, the core rail must rise monotonically before or with the 5 V rail to prevent I/O latch-up; design teams should add a small MOSFET or supervisor (e.g. NCP347) to enforce ordering. Place at least eight 100 nF X7R ceramic decoupling capacitors evenly around the perimeter of the 388-BGA to suppress switching transients on the core rail.
The 388-PBGA at 27x27 mm requires a multilayer PCB with at least 4 layers (signal, ground, power, signal) and via-in-pad or microvia technology for reliable BGA breakout. Estimated: with a 1.0 mm ball pitch the breakout fan-out needs at least 4 routing layers; ensure the inner ground plane is contiguous under the BGA to provide a low-impedance return path for high-speed signals. Avoid routing high-current motor or solenoid traces directly under the BGA to prevent inductive coupling into the sensitive analog sections.
Three common pitfalls when designing with the MPC565CVR40: (1) using a non-NXP-authorized source and risking counterfeit parts, since the device is NRND; (2) failing to assign all unused GPIO to defined states (input with pull-up) to minimize inrush during power-up; (3) neglecting the QADC input clamping diodes when interfacing to 12 V automotive rails - always add external series resistors and TVS protection. Validate firmware shadow-row updates under all power-failure scenarios before locking the boot ROM configuration.
معلومات الامتثال
RoHS/REACH compliance status was not available in the verified distributor data. AEC-Q100 qualification is part-specific and should be confirmed via the NXP Certificate of Conformance. As an NRND part, lot-level compliance documentation may be limited; verify with the authorized franchised distributor before RoHS-bound assembly.