PCA9536YZPR - 4-Bit 400kHz I2C I/O Expander | Texas Instruments
MPN: PCA9536YZPR ✓ نشطPCA9536YZPR نظرة عامة
An I/O expander is an interface IC that translates a serial I2C connection into additional parallel input and output lines. This expands the number of pins available on a host controller without requiring a larger microcontroller package. The PCA9536 belongs to the broader parallel I/O interface hierarchy and is commonly used where a system needs control, status, chip-select, or interrupt signals beyond the native GPIO count of its main processor.
Key features include a low standby-current consumption of 1 uA maximum, 5 V tolerant I/O ports, configuration registers, and a polarity-inversion register. An internal power-on reset establishes a predictable startup condition, while the device powers up with all channels configured as inputs. Power-up without output glitches helps prevent unintended commands or signal transitions in connected equipment.
The PCA9536 uses configuration registers to control each channel direction and input polarity. Its I2C interface supports device addressing so multiple expanders can share the same bus, while 400 kHz fast-mode operation provides a practical balance between transfer rate, wiring distance, and system clock budget. The 5 V tolerant ports also support mixed-voltage systems when the supply and logic conditions are compatible with the device limits.
Typical uses include industrial controllers, sensor-hub boards, programmable logic interfaces, communication equipment, test and measurement systems, and compact embedded products. The device is especially useful when adding a few discrete signals would otherwise force a larger microcontroller, connector, or board footprint.
Designers should account for the compact 1.9 mm by 0.9 mm BGA land pattern, ball pitch, assembly capability, and available thermal copper during layout. Firmware should also confirm the intended I2C address and initialize direction and polarity registers before driving any external hardware.
This page combines the manufacturer product information, exact package characteristics, interface functions, application guidance, and verified replacement analysis. It also distinguishes a true same-footprint replacement from devices that are merely functionally similar, helping engineers avoid unnecessary PCB or firmware changes.
بدائل مباشرة لـ PCA9536YZPR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلPCA9536YZPR المواصفات
| Number of I/O Ports | 4 ports |
| نوع الواجهة | I2C and SMBus |
| Maximum I2C Bus Frequency | 400 kHz |
| Operating Supply Voltage Range | 2.3 V to 5.5 V |
| Standby Current Consumption | 1 uA maximum |
| I/O Port Voltage Tolerance | 5 V tolerant |
| Configuration Register | 1 input/output configuration register |
| Polarity Inversion Register | 1 polarity inversion register |
| Power-On Reset | Internal power-on reset |
| Power-Up Port State | All channels configured as inputs |
| Power-Up Glitch Control | No glitch on power-up |
| Noise Filter | Internal noise filter on I2C inputs |
| نطاق درجة حرارة التشغيل | -40 C to +85 C |
| Temperature Grade | Industrial |
| العلبة | 8-DSBGA, 1.9 mm x 0.9 mm |
| Terminal Count | 8 terminals |
| Terminal Form | Ball |
| Package Shape | Rectangular |
| Technology | CMOS |
| حالة RoHS | unknown |
| REACH Status | unknown |
دليل تكوين أطراف PCA9536YZPR rectangular
تكوين الأطراف لـ PCA9536YZPR (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ PCA9536YZPR.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
PCA9536YZPR مناسب لـ 6 التطبيقs: Industrial Control and Sensor Interface, Communication Equipment Status Control, Compact Embedded Control Module, USB and Peripheral Configuration, Test and Measurement Front Panel, Low-Power Portable and Wearable Device.
Industrial Control and Sensor Interface
The PCA9536YZPR fits industrial control boards that need a small number of discrete signals in addition to a host controller’s native GPIO. Its four configurable ports can collect sensor status, select peripheral modes, or drive control lines while the host communicates through I2C at up to 400 kHz. The 2.3 V to 5.5 V operating range supports common industrial logic levels, and the 5 V tolerant inputs improve interface flexibility. Because all channels start as inputs after power-on, the design can prevent unintended actuator activation. The compact 8-DSBGA package also helps preserve board area in densely populated control systems, although the 1.9 mm by 0.9 mm land pattern requires capable assembly and inspection processes.
موصى به
Communication Equipment Status Control
The PCA9536YZPR is useful in communication equipment where front-panel indicators, relay selects, module enables, or fault inputs must be added without enlarging the main controller. A 400 kHz I2C connection provides an efficient path for updating several outputs, while the four ports can be individually configured as inputs or outputs. The polarity-inversion register helps accommodate active-low module-control signals without changing external logic. Its 1 uA maximum standby current also suits low-activity or intermittently powered equipment. Designers should allocate bus pull-ups correctly, define deterministic startup states in firmware, and verify that the small DSBGA assembly supports the product’s manufacturing and inspection requirements.
موصى به
Compact Embedded Control Module
The PCA9536YZPR can extend a small microcontroller module when a system needs four extra lines but cannot justify a larger controller package. The expander translates I2C commands into parallel input or output operations, reducing the host’s pin burden and freeing board space for sensing, power, or communications. Its wide 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic domains, while the polarity control can simplify interfacing to active-low peripherals. The internal power-on reset and input-only startup provide a safer initial state for external hardware. Firmware should initialize direction and polarity before asserting outputs, and the PCB should follow the official ball pattern exactly to avoid assembly and rework risk.
موصى به
USB and Peripheral Configuration
The PCA9536YZPR can add configuration and status lines to USB-enabled embedded controllers without consuming additional connector or host-controller pins. A USB bridge or embedded controller may write to the configuration register to set selected lines as outputs, then use the other ports as inputs for button, latch, or peripheral-fault feedback. The 400 kHz I2C rate is adequate for infrequent control traffic, and the small DSBGA footprint preserves board area in compact USB accessories. The device’s 5 V tolerant ports assist when downstream logic uses a higher voltage than the host controller. System firmware should avoid driving outputs before completing register initialization, and production tests should verify bus addressing, startup behavior, and logic polarity.
موصى به
Test and Measurement Front Panel
The PCA9536YZPR is well suited to test and measurement front panels where range selection, relay enables, status LEDs, or remote-control inputs must be multiplexed over a compact control bus. Four I/O lines can be assigned independently through the configuration register, and polarity inversion simplifies active-high versus active-low control conventions. The 400 kHz I2C interface supports prompt command updates, while the low 1 uA maximum standby current is beneficial in portable instruments. The -40 C to +85 C industrial temperature range supports equipment intended for controlled industrial environments. Layout should keep the compact BGA away from high-current switching nodes and provide unobstructed assembly access. Firmware should maintain a defined state table for each output to prevent unintended switching during startup or fault recovery.
موصى به
Low-Power Portable and Wearable Device
The PCA9536YZPR can add a few low-rate control or status lines to compact portable equipment without requiring a larger general-purpose microcontroller. The 2.3 V to 5.5 V supply range is compatible with common embedded logic, and standby-current consumption up to 1 uA is valuable when the main device spends most of its time in a low-power state. Typical uses include accessory detection, user-interface indicators, or battery-system status inputs. The input-only power-up state helps prevent accidental activation of connected hardware. Because the package is only 1.9 mm by 0.9 mm, designers must validate board assembly, inspection, and repair capability. Firmware should release the host bus only after the expander address and configuration are stable.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PCA9536YZPR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Package | 8-DSBGA, 1.9 mm x 0.9 mm |
| Brand | Texas Instruments |
| Number of I/O Ports | 4 ports |
| Interface | I2C and SMBus |
| Maximum I2C Frequency | 400 kHz |
| Operating Supply Voltage | 2.3 V to 5.5 V |
| I/O Port Tolerance | 5 V tolerant |
| Standby Current | 1 uA maximum |
| Operating Temperature | -40 C to +85 C |
| Power-On Port State | All channels configured as inputs |
أبرز الفروقات
- Exceptionally compact 4-bit expansion footprint (مقابلPCA9536DGKR)
- Five-volt-tolerant port interfaces (مقابلPCA9536DGKR)
- Predictable power-up behavior (مقابلGeneric four-bit I/O expander)
ملاحظات التصميم
Use the official Texas Instruments PCA9536 package drawing to define the 8-DSBGA land pattern, solder-mask openings, and ball numbering for PCA9536YZPR. The 1.9 mm by 0.9 mm package is unusually compact, so check the PCB fabrication capability, assembly process, and inspection method before layout release. Keep the footprint unobstructed by enclosure hardware and provide solderable copper beneath the component according to the manufacturer land-pattern guidance.
Place the I2C pull-up resistors and local supply-decoupling capacitor close to the appropriate bus and device pins. Determine pull-up resistance from the logic voltage, total bus capacitance, required rise time, and the sink-current rating of the host and PCA9536. Check the 2.3 V to 5.5 V operating range against both supply tolerances and external signal levels. The 5 V tolerant I/O capability must not be interpreted as permission to exceed the absolute maximum ratings.
Do not assume that power-up configuration equals the desired operational configuration. The PCA9536YZPR powers up with all channels configured as inputs, so firmware should set direction and polarity registers before releasing external enables or writing to latches. Review the device address configuration for every node on a shared I2C bus, and confirm register behavior against the manufacturer datasheet before reusing firmware written for a different I/O expander.
Keep the compact BGA away from high-voltage nodes, fast-switching power stages, and sources of EMI unless the complete system has appropriate isolation and filtering. Route the serial bus away from sensitive analog inputs, use a continuous ground reference, and avoid long unprotected branches from the main bus. Although the device is a digital interface, its I2C edges and external port transitions can couple into adjacent circuitry; ground and return-path planning are especially important in mixed-signal boards.
معلومات الامتثال
The manufacturer product information identifies an industrial-temperature device but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.