Texas Instruments

PCA9536YZPR - 4-Bit 400kHz I2C I/O Expander | Texas Instruments

MPN: PCA9536YZPR ✓ فعال
2.3 V to 5.5 V Vdss 1 uA maximum Id 8-DSBGA, 1.9 mm x 0.9 mm Package 400 kHz Speed
حداقل سفارش: 1 |

PCA9536YZPR نمای کلی

The Texas Instruments PCA9536YZPR is a 4-bit I2C and SMBus I/O expander operating from 2.3 V to 5.5 V, supporting bus speeds up to 400 kHz in an 8-DSBGA package measuring 1.9 mm by 0.9 mm. Its four configurable I/O ports can operate as inputs or outputs and include polarity-inversion control for direct interface to external logic.

An I/O expander is an interface IC that translates a serial I2C connection into additional parallel input and output lines. This expands the number of pins available on a host controller without requiring a larger microcontroller package. The PCA9536 belongs to the broader parallel I/O interface hierarchy and is commonly used where a system needs control, status, chip-select, or interrupt signals beyond the native GPIO count of its main processor.

Key features include a low standby-current consumption of 1 uA maximum, 5 V tolerant I/O ports, configuration registers, and a polarity-inversion register. An internal power-on reset establishes a predictable startup condition, while the device powers up with all channels configured as inputs. Power-up without output glitches helps prevent unintended commands or signal transitions in connected equipment.

The PCA9536 uses configuration registers to control each channel direction and input polarity. Its I2C interface supports device addressing so multiple expanders can share the same bus, while 400 kHz fast-mode operation provides a practical balance between transfer rate, wiring distance, and system clock budget. The 5 V tolerant ports also support mixed-voltage systems when the supply and logic conditions are compatible with the device limits.

Typical uses include industrial controllers, sensor-hub boards, programmable logic interfaces, communication equipment, test and measurement systems, and compact embedded products. The device is especially useful when adding a few discrete signals would otherwise force a larger microcontroller, connector, or board footprint.

Designers should account for the compact 1.9 mm by 0.9 mm BGA land pattern, ball pitch, assembly capability, and available thermal copper during layout. Firmware should also confirm the intended I2C address and initialize direction and polarity registers before driving any external hardware.

This page combines the manufacturer product information, exact package characteristics, interface functions, application guidance, and verified replacement analysis. It also distinguishes a true same-footprint replacement from devices that are merely functionally similar, helping engineers avoid unnecessary PCB or firmware changes.

جایگزین‌های drop-in برای PCA9536YZPR — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

هیچ جایگزین مستقیمی برای این محصول موجود نیست.

درخواست جایگزین

PCA9536YZPR مشخصات

Number of I/O Ports 4 ports
نوع رابط I2C and SMBus
Maximum I2C Bus Frequency 400 kHz
Operating Supply Voltage Range 2.3 V to 5.5 V
Standby Current Consumption 1 uA maximum
I/O Port Voltage Tolerance 5 V tolerant
Configuration Register 1 input/output configuration register
Polarity Inversion Register 1 polarity inversion register
Power-On Reset Internal power-on reset
Power-Up Port State All channels configured as inputs
Power-Up Glitch Control No glitch on power-up
Noise Filter Internal noise filter on I2C inputs
محدوده دمای کاری -40 C to +85 C
Temperature Grade Industrial
بسته‌بندی 8-DSBGA, 1.9 mm x 0.9 mm
Terminal Count 8 terminals
Terminal Form Ball
Package Shape Rectangular
Technology CMOS
وضعیت RoHS unknown
REACH Status unknown

راهنمای پیکربندی پین PCA9536YZPR rectangular

پیکربندی پین برای PCA9536YZPR (پکیج rectangular). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج rectangular برای PCA9536YZPR

داده پین‌آوت تفصیلی موجود نیست برای PCA9536YZPR.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

PCA9536YZPR مناسب است برای 6 کاربردs: Industrial Control and Sensor Interface, Communication Equipment Status Control, Compact Embedded Control Module, USB and Peripheral Configuration, Test and Measurement Front Panel, Low-Power Portable and Wearable Device.

🏭

Industrial Control and Sensor Interface

The PCA9536YZPR fits industrial control boards that need a small number of discrete signals in addition to a host controller’s native GPIO. Its four configurable ports can collect sensor status, select peripheral modes, or drive control lines while the host communicates through I2C at up to 400 kHz. The 2.3 V to 5.5 V operating range supports common industrial logic levels, and the 5 V tolerant inputs improve interface flexibility. Because all channels start as inputs after power-on, the design can prevent unintended actuator activation. The compact 8-DSBGA package also helps preserve board area in densely populated control systems, although the 1.9 mm by 0.9 mm land pattern requires capable assembly and inspection processes.

🌐

Communication Equipment Status Control

The PCA9536YZPR is useful in communication equipment where front-panel indicators, relay selects, module enables, or fault inputs must be added without enlarging the main controller. A 400 kHz I2C connection provides an efficient path for updating several outputs, while the four ports can be individually configured as inputs or outputs. The polarity-inversion register helps accommodate active-low module-control signals without changing external logic. Its 1 uA maximum standby current also suits low-activity or intermittently powered equipment. Designers should allocate bus pull-ups correctly, define deterministic startup states in firmware, and verify that the small DSBGA assembly supports the product’s manufacturing and inspection requirements.

🧩

Compact Embedded Control Module

The PCA9536YZPR can extend a small microcontroller module when a system needs four extra lines but cannot justify a larger controller package. The expander translates I2C commands into parallel input or output operations, reducing the host’s pin burden and freeing board space for sensing, power, or communications. Its wide 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic domains, while the polarity control can simplify interfacing to active-low peripherals. The internal power-on reset and input-only startup provide a safer initial state for external hardware. Firmware should initialize direction and polarity before asserting outputs, and the PCB should follow the official ball pattern exactly to avoid assembly and rework risk.

🔌

USB and Peripheral Configuration

The PCA9536YZPR can add configuration and status lines to USB-enabled embedded controllers without consuming additional connector or host-controller pins. A USB bridge or embedded controller may write to the configuration register to set selected lines as outputs, then use the other ports as inputs for button, latch, or peripheral-fault feedback. The 400 kHz I2C rate is adequate for infrequent control traffic, and the small DSBGA footprint preserves board area in compact USB accessories. The device’s 5 V tolerant ports assist when downstream logic uses a higher voltage than the host controller. System firmware should avoid driving outputs before completing register initialization, and production tests should verify bus addressing, startup behavior, and logic polarity.

📺

Test and Measurement Front Panel

The PCA9536YZPR is well suited to test and measurement front panels where range selection, relay enables, status LEDs, or remote-control inputs must be multiplexed over a compact control bus. Four I/O lines can be assigned independently through the configuration register, and polarity inversion simplifies active-high versus active-low control conventions. The 400 kHz I2C interface supports prompt command updates, while the low 1 uA maximum standby current is beneficial in portable instruments. The -40 C to +85 C industrial temperature range supports equipment intended for controlled industrial environments. Layout should keep the compact BGA away from high-current switching nodes and provide unobstructed assembly access. Firmware should maintain a defined state table for each output to prevent unintended switching during startup or fault recovery.

📱

Low-Power Portable and Wearable Device

The PCA9536YZPR can add a few low-rate control or status lines to compact portable equipment without requiring a larger general-purpose microcontroller. The 2.3 V to 5.5 V supply range is compatible with common embedded logic, and standby-current consumption up to 1 uA is valuable when the main device spends most of its time in a low-power state. Typical uses include accessory detection, user-interface indicators, or battery-system status inputs. The input-only power-up state helps prevent accidental activation of connected hardware. Because the package is only 1.9 mm by 0.9 mm, designers must validate board assembly, inspection, and repair capability. Firmware should release the host bus only after the expander address and configuration are stable.

What is the PCA9536YZPR used for?
The PCA9536YZPR is a 4-bit I2C and SMBus I/O expander that adds four configurable parallel lines to a serial bus host. Each port can be configured as an input or output, and the polarity-inversion register can reverse active-high or active-low input interpretation. According to the Texas Instruments product information, the device supports a 2.3 V to 5.5 V operating-supply range and I2C operation up to 400 kHz, making it suitable for control, status, and discrete interface signals in embedded systems.
What is the operating voltage of PCA9536YZPR?
The PCA9536YZPR operates from 2.3 V to 5.5 V. This range allows the expander to interface with common 3.3 V and 5 V embedded systems while retaining 5 V tolerant I/O ports. The Texas Instruments manufacturer product page identifies the 2.3 V to 5.5 V range, and the manufacturer datasheet describes the associated 5 V tolerant port behavior. The supply and external signal voltages must still remain within the limits specified for the operating conditions.
How many I/O ports does PCA9536YZPR have?
The PCA9536YZPR provides four configurable I/O ports. The Texas Instruments product page identifies it as a 4-bit I2C and SMBus expander, while the manufacturer datasheet describes individual direction control through configuration registers and adjustable input polarity through a polarity-inversion register. All four channels begin in the input state after power-up, which reduces the chance of an unintended output transition while the host initializes the device.
Is PCA9536YZPR compatible with 400 kHz I2C?
Yes, the PCA9536YZPR supports I2C operation up to 400 kHz. The Texas Instruments manufacturer datasheet identifies the 400 kHz fast-I2C capability and describes internal noise filtering on the serial inputs. Actual bus timing also depends on the host controller, wiring, pull-up resistance, bus capacitance, and every device placed on the same bus, so a complete system should be checked against the applicable I2C timing requirements rather than relying on the expander rating alone.
Where can I download the PCA9536YZPR datasheet PDF?
The official PCA9536YZPR documentation is available through the Texas Instruments PCA9536 product page at https://www.ti.com/product/PCA9536. From that page, the manufacturer datasheet can be opened or downloaded for the PCA9536 family. The document defines the electrical characteristics, register map, device addressing, input and output behavior, application information, and package details. Use the ordering information to confirm that the YZP package code corresponds to the PCA9536YZPR configuration.
Where can I find the PCA9536YZPR pinout and package drawing?
The PCA9536YZPR pin assignment and mechanical drawing are in the official Texas Instruments PCA9536 manufacturer datasheet under the package information and pin configuration sections. The YZP ordering code uses an 8-DSBGA package measuring 1.9 mm by 0.9 mm. Because this package is smaller than the common BGA diagrams represented in standard symbol libraries, use the manufacturer drawing directly when assigning ball locations, solder-mask apertures, and PCB land patterns.
Can PCA9536DGKR replace PCA9536YZPR without PCB changes?
No. The PCA9536DGKR has the same 4-bit I2C expander function, 2.3 V to 5.5 V supply range, and compatible serial interface, but it uses a different physical package from the PCA9536YZPR. The PCA9536YZPR is an 8-DSBGA measuring 1.9 mm by 0.9 mm, while the DGKR uses the DGK package. Treat the DGKR as a functionally similar device rather than a true drop-in replacement; changing packages requires PCB, assembly, and layout review.
What is the best drop-in replacement for PCA9536YZPR?
No independently verified drop-in replacement for the exact PCA9536YZPR footprint was established. A functional replacement must use the same 8-DSBGA, 1.9 mm by 0.9 mm package, preserve the 2.3 V to 5.5 V supply range and 400 kHz I2C interface, and retain compatible register and pin behavior. The PCA9536DGKR is functionally close but uses a different package. Before adopting another manufacturer’s device, request its complete ordering information, pinout, register map, and package drawing for engineering verification.
PCA9536YZPR vs PCA9536DGKR - which is better for a 3.3 V system?
Both devices support a 2.3 V to 5.5 V operating range and can operate in a 3.3 V system, but the PCA9536YZPR is preferable when the existing PCB uses its 8-DSBGA footprint. The PCA9536DGKR uses another package and is therefore not a board-level drop-in choice. The deciding factors are footprint compatibility, assembly capability, exact pin functions, address scheme, and register behavior rather than supply voltage alone. Check the manufacturer datasheet for each ordering code before changing the schematic or PCB.
When should I choose PCA9536YZPR over another 4-bit I/O expander?
Choose the PCA9536YZPR when a design specifically uses its 8-DSBGA footprint, 2.3 V to 5.5 V supply range, four configurable I/O channels, and 400 kHz I2C interface. Its polarity-inversion capability, internal power-on reset, input-only startup state, and 1 uA maximum standby current are useful for compact control and status interfaces. Select another device when a different package, more I/O channels, a different address range, or a different electrical interface is more important than preserving the PCA9536YZPR layout.
Is PCA9536YZPR suitable for industrial and battery-powered equipment?
The PCA9536YZPR is suitable for industrial and low-power interface designs within its specified operating limits. The Texas Instruments product information gives an industrial temperature range of -40 C to +85 C, and the manufacturer datasheet specifies standby-current consumption up to 1 uA. In battery-powered equipment, account for operating current as well as standby current, and use the power-on input configuration to prevent accidental peripheral activation. For exposed or battery-isolated systems, confirm temperature and power-sequencing requirements during qualification.
Does PCA9536YZPR provide pull-up pins or onboard pull-ups?
The PCA9536YZPR is primarily an I2C-to-parallel interface device, and the product description does not identify dedicated pull-up pins as part of its stated feature set. External pull-up resistors are generally required on an I2C bus unless another device on the same bus already provides them. Select resistor values using the bus voltage, capacitance, rise-time requirement, and sink-current capability of the connected devices. The exact PCA9536 datasheet should be used for electrical and application details.
Where can I buy PCA9536YZPR and check its current availability?
Use the Request a Quote form on this page to request the current PCA9536YZPR price, stock status, minimum order quantity, and lead time for the required 8-DSBGA ordering code. Availability can change by package, production status, and order quantity, so confirm the complete manufacturer part number before accepting a quotation. The product is listed as active by the manufacturer. The form is also the appropriate route for volume pricing and schedule confirmation without relying on a static price.
What are the key specifications of PCA9536YZPR that engineers should know?
The key specifications are four configurable I/O ports, a 2.3 V to 5.5 V operating-supply range, 400 kHz I2C operation, 5 V tolerant ports, and a 1 uA maximum standby current. The device also provides configuration registers, polarity inversion, an internal power-on reset, input-only startup, and no-glitch power-up behavior. Texas Instruments packages it as an 8-DSBGA measuring 1.9 mm by 0.9 mm with an industrial temperature range of -40 C to +85 C.
What can replace PCA9536YZPR in an existing design?
A replacement can be selected functionally, but a replacement that requires no PCB changes must match the PCA9536YZPR package, electrical limits, I2C behavior, address scheme, and register functions. The PCA9536DGKR is a functionally similar 4-bit I2C expander, but its package differs from the 1.9 mm by 0.9 mm 8-DSBGA used by the PCA9536YZPR. For a true drop-in device, request manufacturer pin and package documentation and verify every ball position and register bit before release.

داده‌های مرجع مهندسی برای PCA9536YZPR — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the PCA9536YZPR when a compact PCB already uses the 1.9 mm by 0.9 mm 8-DSBGA footprint and the design needs four configurable I/O ports over an I2C or SMBus connection. Its 2.3 V to 5.5 V operating range, 400 kHz bus support, 5 V tolerant ports, polarity inversion, and input-only startup state are useful for compact industrial, communication, portable, and test-equipment interfaces. Select a different PCA9536 ordering code when another package offers a better manufacturing or assembly fit, but verify all pin and register differences. The PCA9536DGKR is functionally similar, yet its different package means it is not a no-change PCB replacement. For any new cross-manufacturer candidate, require documented pin compatibility, package dimensions, electrical limits, address behavior, and register mapping before considering it a drop-in alternative.

مقایسه با جایگزین‌ها

پارامتر این محصول
Package 8-DSBGA, 1.9 mm x 0.9 mm
Brand Texas Instruments
Number of I/O Ports 4 ports
Interface I2C and SMBus
Maximum I2C Frequency 400 kHz
Operating Supply Voltage 2.3 V to 5.5 V
I/O Port Tolerance 5 V tolerant
Standby Current 1 uA maximum
Operating Temperature -40 C to +85 C
Power-On Port State All channels configured as inputs

تفاوت‌های کلیدی

  • Exceptionally compact 4-bit expansion footprint (در مقابلPCA9536DGKR)
  • Five-volt-tolerant port interfaces (در مقابلPCA9536DGKR)
  • Predictable power-up behavior (در مقابلGeneric four-bit I/O expander)

یادداشت‌های طراحی

Use the official Texas Instruments PCA9536 package drawing to define the 8-DSBGA land pattern, solder-mask openings, and ball numbering for PCA9536YZPR. The 1.9 mm by 0.9 mm package is unusually compact, so check the PCB fabrication capability, assembly process, and inspection method before layout release. Keep the footprint unobstructed by enclosure hardware and provide solderable copper beneath the component according to the manufacturer land-pattern guidance.

Place the I2C pull-up resistors and local supply-decoupling capacitor close to the appropriate bus and device pins. Determine pull-up resistance from the logic voltage, total bus capacitance, required rise time, and the sink-current rating of the host and PCA9536. Check the 2.3 V to 5.5 V operating range against both supply tolerances and external signal levels. The 5 V tolerant I/O capability must not be interpreted as permission to exceed the absolute maximum ratings.

Do not assume that power-up configuration equals the desired operational configuration. The PCA9536YZPR powers up with all channels configured as inputs, so firmware should set direction and polarity registers before releasing external enables or writing to latches. Review the device address configuration for every node on a shared I2C bus, and confirm register behavior against the manufacturer datasheet before reusing firmware written for a different I/O expander.

Keep the compact BGA away from high-voltage nodes, fast-switching power stages, and sources of EMI unless the complete system has appropriate isolation and filtering. Route the serial bus away from sensitive analog inputs, use a continuous ground reference, and avoid long unprotected branches from the main bus. Although the device is a digital interface, its I2C edges and external port transitions can couple into adjacent circuitry; ground and return-path planning are especially important in mixed-signal boards.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer product information identifies an industrial-temperature device but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

PCA9536YZPR datasheet PCA9536YZPR pinout PCA9536YZPR datasheet pdf PCA9536YZPR equivalent PCA9536YZPR replacement PCA9536YZPR 8-DSBGA PCA9536YZPR price PCA9536YZPR stock Texas Instruments PCA9536YZPR PCA9536YZPR vs PCA9536DGKR PCA9536YZPR I2C 400 kHz PCA9536YZPR application circuit

قطعات و اصطلاحات مرتبط

Texas Instruments PCA9536YZPR PCA9536 PCA9536DGKR I2C SMBus I/O expander parallel I/O interface interface IC semiconductor configuration register polarity inversion register 4-bit I/O 400 kHz fast-mode I2C 5 V tolerant I/O 8-DSBGA DSBGA ball grid array surface-mount package internal power-on reset 1 uA standby current industrial temperature range embedded system sensor interface
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ