PCA9544APW - 4-Channel I2C Switch | NXP | Embedded
MPN: PCA9544APW ✓ نشطPCA9544APW نظرة عامة
An I2C-bus multiplexer is a switching interface that expands a single serial bus into multiple selectable downstream branches. It belongs to the interface IC hierarchy, where bus switches and multiplexers manage address, command, and data routing between a controller and multiple peripheral devices. Unlike a passive hub, this device provides controlled channel selection and bidirectional signal translation.
The PCA9544APW includes four selectable downstream channels, interrupt logic for downstream alert signaling, and bidirectional upstream and downstream SCL/SDA connections. Its 400 kHz bus capability suits conventional I2C systems operating below the maximum Standard-mode frequency. The 20-pin TSSOP package supports compact PCB layouts in embedded control, industrial instrumentation, and consumer equipment.
Channel selection is performed through the upstream I2C control interface. The active configuration determines which SCx/SDx pair is connected to the common SCL/SDA bus, allowing a controller to address devices on only one branch at a time. Interrupt logic provides a dedicated path for downstream events, helping the host detect activity without continuously polling every channel.
Typical applications include sensor aggregation, programmable power supplies, EEPROM banks, communication interfaces, and industrial modules that place multiple devices behind one host bus. The four-channel architecture reduces the number of host GPIO pins and wiring connections required when peripheral addresses cannot all coexist on a single I2C segment.
During layout, keep the upstream and selected downstream routing short, follow the datasheet recommendations for pull-up resistors, and account for bus capacitance when selecting the operating speed. Pull-ups should normally be placed according to the system-level I2C topology rather than duplicated on every downstream branch.
This product page combines device functionality, verified source links, replacement guidance, application-specific design considerations, and parameter comparisons. These engineering details help distinguish a true same-package replacement from devices that merely perform a similar multiplexing function or require a different PCB footprint.
بدائل مباشرة لـ PCA9544APW — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PCA9544APW (نفس عامل الشكل والبصمة) — يختلف في Number of Channels, Package, Interrupt Logic, RoHS Status, Supply Voltage Range.
PCA9544ARGYR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PCA9544APW الحدود القصوى والخصائص الكهربائية
| Product Type | 4-channel bidirectional I2C-bus translating multiplexer |
| Number of Channels | 4 channels |
| Upstream Bus Pairs | 1 SCL/SDA pair |
| Downstream Bus Pairs | 4 SCx/SDx pairs |
| Simultaneously Selected Channels | 1 channel |
| I2C-Bus Frequency | 400 kHz |
| Signal Direction | Bidirectional |
| Interrupt Logic | Included |
| العلبة | 20-pin TSSOP |
| نوع التركيب | Surface mount |
| Device Classification | Translating switch interface IC |
| حالة دورة الحياة | Active |
دليل تكوين أطراف PCA9544APW 20-pin tssop
تكوين الأطراف لـ PCA9544APW (حزمة 20-pin tssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ PCA9544APW.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
PCA9544APW مناسب لـ 6 التطبيقs: Multi-Sensor Acquisition, Programmable Power Supply Control, Industrial Instrumentation, EEPROM and Configuration Banks, Communication Interface Isolation, Embedded Control Hubs.
Multi-Sensor Acquisition
The PCA9544APW fits multi-sensor acquisition systems in which several sensor groups cannot occupy one I2C segment or share identical addresses. Its four selectable SCx/SDx branches connect one at a time to the upstream controller, while the 400 kHz bus rate accommodates many standard embedded sensors. Place each sensor group behind its assigned downstream pair and use software to select the required branch. Because only one channel conducts at a time, the host must avoid simultaneous commands to devices on different branches. Bus capacitance and pull-up values should be calculated for the longest selected path, while interrupt logic can signal downstream activity and reduce unnecessary polling.
موصى به
Programmable Power Supply Control
The PCA9544APW can separate multiple digital monitoring or configuration paths used in programmable power-supply controllers. Four downstream SCx/SDx pairs allow temperature sensors, current monitors, EEPROMs, or configuration devices to share a compact controller footprint even when their address requirements differ. The 400 kHz I2C rate provides adequate control bandwidth for supervisory reads and parameter updates. Firmware should select one branch for each transaction and avoid simultaneous downstream activity. Pull-up placement must preserve a valid bus topology across the selected channel, and the interrupt path can indicate a downstream event requiring prompt attention.
موصى به
Industrial Instrumentation
The PCA9544APW is useful in industrial instrumentation modules that combine several low-speed I2C peripherals behind a single host interface. The four-channel architecture reduces duplicated wiring and can separate devices with conflicting addresses or different update schedules. Its bidirectional translating-switch architecture and 400 kHz operating rate support controller-to-sensor and sensor-to-controller traffic. The TSSOP-20 package leaves board area for analog and power circuitry, but thermal and environmental requirements should be checked against the selected ordering option. Interrupt logic can support responsive detection of remote events while the controller polls only the branch that requires service.
موصى به
EEPROM and Configuration Banks
The PCA9544APW can organize EEPROM and configuration-device banks on boards where multiple parts cannot coexist on one unsegmented I2C bus. Four selectable downstream pairs let a controller address one memory bank at a time through a common upstream SCL/SDA connection. The 400 kHz limit is suitable for many configuration and EEPROM transactions, while interrupt logic can provide an alert path from downstream devices that support it. Firmware should include channel selection in each transfer sequence and account for the extra bus turnaround overhead. PCB pull-ups should be arranged to prevent multiple inactive branches from loading the selected channel.
موصى به
Communication Interface Isolation
The PCA9544APW can partition communication-related I2C peripherals into individually selectable branches, helping a host avoid simultaneous activity on separate downstream segments. Its four SCx/SDx pairs and bidirectional routing support sensors, transceivers, and status devices that share a common upstream bus. At up to 400 kHz, the device is best matched to control traffic rather than high-bandwidth payload transfers. Interrupt logic allows a system to react to selected downstream alert conditions. The layout should minimize stubs on the active channel and use a pull-up strategy that remains valid when different branches are enabled over the product lifecycle.
موصى به
Embedded Control Hubs
The PCA9544APW fits embedded control hubs that need to connect four groups of I2C peripherals to one processor or microcontroller. It replaces several direct host-bus branches with a controlled multiplexer while preserving four possible downstream paths. The 20-pin TSSOP package supports dense layouts, and the 400 kHz bus rate is suitable for configuration, monitoring, and sensor-control traffic. The selected channel should be driven for the duration of a transaction, and firmware should not assume that multiple downstream devices can communicate concurrently. Correct external pull-up placement and channel-aware capacitance checks are essential for reliable operation at the upper bus rate.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PCA9544APW — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | PCA9544A |
|---|---|---|
| Package | 20-pin TSSOP | 20-pin TSSOP (PW) |
| Brand | NXP Semiconductors | Texas Instruments |
| Channel Count | 4 channels | 4 channels |
أبرز الفروقات
- Four independently selectable I2C branches (مقابلPCA9544A)
- Integrated downstream interrupt handling (مقابلPCA9544A)
- Standard-mode I2C throughput (مقابلPCA9544A)
ملاحظات التصميم
Route the upstream SCL/SDA pair and every downstream SCx/SDx pair as short, controlled branches. Avoid long stubs because capacitance increases with trace length and can reduce the reliable bus margin at 400 kHz. Follow the manufacturer application circuit for pull-up placement, and ensure inactive branches do not create excessive parallel loading on the selected channel.
Treat the selected downstream channel as the active I2C segment and include channel-selection time in the controller timing budget. The PCA9544APW connects one downstream pair at a time, so simultaneous transactions on different branches are not supported. Confirm rise-time behavior with the actual bus capacitance and pull-up resistance before selecting the maximum operating frequency.
Use stable bypass capacitance at the device supply pins and place the decoupling components close to the package according to the manufacturer layout guidance. Keep switching regulators and high-current digital nodes separated from the I2C traces where practical, because supply disturbance can affect bus levels even when the selected downstream channel is inactive.
Do not treat a shared TSSOP package as proof of complete compatibility. Before replacing PCA9544APW, compare pin names, address-control behavior, interrupt polarity, electrical limits, supply range, and timing requirements. A production substitution should also be checked for differences in channel isolation, power consumption, and default control-register state.
معلومات الامتثال
The product is an active I2C interface IC. Specific environmental and material-compliance declarations must be confirmed for the selected orderable configuration.