PIC18F97J60-I/PT - 8-bit MCU w/ 10Mbps Ethernet, 128KB Flash
MPN: PIC18F97J60-I/PT ✓ نشطPIC18F97J60-I/PT نظرة عامة
A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash), data memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, communication controllers, and I/O ports. The PIC18F97J60 belongs to Microchip's PIC18J family, which uses a 16-bit enhanced Harvard architecture that targets higher-performance, Ethernet-connected embedded designs. Its hierarchy places it within 8-bit microcontrollers -> Microchip PIC family -> PIC18 high-performance sub-family -> PIC18J Ethernet-enabled series.
Key features include the integrated IEEE 802.3 10BASE-T Ethernet controller with on-chip PHY and dedicated DMA, an 8-channel hardware modulator for IrDA/SIR, two MSSP (SPI/I2C) ports, two USART modules, two capture/compare/PWM modules, and 70 I/O pins. The on-chip PHY eliminates external Ethernet magnetics and dramatically reduces BOM cost compared to MCU-plus-external-MAC designs.
The device uses an enhanced RISC pipeline with 32-level hardware stack and vectored interrupts, executed from Flash or external memory. The 100-pin TQFP package provides abundant I/O for parallel buses and memory-mapped LCDs, while a wide operating voltage of 2.0-3.6 V and -40C to +85C industrial temperature range support harsh industrial environments.
Typical applications include industrial automation (Modbus/TCP gateways, remote sensor nodes), building automation (BACnet/IP controllers, access panels), and remote monitoring (web/SCADA interfaces). The integrated Ethernet peripheral makes the part especially attractive for designers replacing RS-485 or CAN-based infrastructure with low-cost TCP/IP connectivity.
When designing with the PIC18F97J60-I/PT, allocate at least 8 KB of Flash for the TCP/IP stack (Microchip's MLA or Harmony-based stack) and carefully observe the Ethernet PCB layout guidelines (4-layer board, controlled-impedance 100-ohm differential traces, dedicated ground pour). The internal 3.3 V LDO must be bypassed with 10 uF and 0.1 uF capacitors placed close to the VDD pins.
بدائل مباشرة لـ PIC18F97J60-I/PT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PIC18F97J60-I/PT (نفس عامل الشكل والبصمة) — يختلف في Package, Program Memory (Flash), RAM, ADC, Core.
PIC18F97J60T-I/PT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PIC18F96J60-I/PT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC18F87J60-I/PT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC18F96J94-I/PF
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PIC18F97J60-I/PT الحدود القصوى والخصائص الكهربائية
| Core Architecture | PIC18, 8-bit enhanced Harvard RISC |
| Instruction Set Width | 16 bits |
| Program Memory (Flash) | 128 KB (64K x 16) |
| RAM | 3808 bytes |
| EEPROM | Not present (uses Flash emulation) |
| Maximum CPU Frequency | 41.667 MHz |
| Instruction Cycle Time | 200 ns |
| Performance | 16 MIPS (million instructions per second) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| درجة حرارة التشغيل | -40 C to +85 C (Industrial) |
| I/O Pins | 70 |
| Ethernet Peripheral | Integrated IEEE 802.3 10BASE-T MAC + PHY |
| ADC | 10-bit, up to 16 channels |
| Communication Peripherals | 2x USART, 2x MSSP (SPI/I2C), 1x Ethernet, 1x IrDA |
| Timers | 5 x 16-bit / 8-bit Timer modules |
| PWM / CCP | 2 Capture/Compare/PWM modules |
| العلبة | 100-pin TQFP (PT), 12x12 mm |
| نوع التركيب | Surface Mount |
| مستوى MSL | 3 (168 hours) |
| حالة RoHS | Compliant |
تكوين أطراف PIC18F97J60-I/PT
| دبوس 1 | RG0/INT0 — PORTG bit 0 / External interrupt 0 |
| دبوس 2 | RG1/INT1 — PORTG bit 1 / External interrupt 1 |
| دبوس 3 | RG2/INT2 — PORTG bit 2 / External interrupt 2 |
| دبوس 4 | RG3/INT3 — PORTG bit 3 / External interrupt 3 |
| دبوس 5 | MCLR — Master Clear (reset) input, active low |
| دبوس 6 | RG4 — PORTG bit 4 |
| دبوس 7 | RG5 — PORTG bit 5 |
| دبوس 8 | VDD — Digital supply voltage (3.3 V) |
| دبوس 9 | VSS — Digital ground |
| دبوس 10 | RF7 — PORTF bit 7 |
| دبوس 11 | RF6 — PORTF bit 6 |
| دبوس 12 | RB7 — PORTB bit 7 |
| دبوس 13 | RB6 — PORTB bit 6 |
| دبوس 14 | RB5 — PORTB bit 5 |
| دبوس 15 | RB4 — PORTB bit 4 |
| دبوس 16 | RB3 — PORTB bit 3 |
| دبوس 17 | RB2 — PORTB bit 2 |
| دبوس 18 | RB1 — PORTB bit 1 |
| دبوس 19 | RB0 — PORTB bit 0 |
| دبوس 20 | VDD — Digital supply voltage (3.3 V) |
| دبوس 21 | VSS — Digital ground |
| دبوس 22 | RD7 — PORTD bit 7 |
| دبوس 23 | RD6 — PORTD bit 6 |
| دبوس 24 | RD5 — PORTD bit 5 |
| دبوس 25 | RD4 — PORTD bit 4 |
| دبوس 26 | RD3 — PORTD bit 3 |
| دبوس 27 | RD2 — PORTD bit 2 |
| دبوس 28 | RD1 — PORTD bit 1 |
| دبوس 29 | RD0 — PORTD bit 0 |
| دبوس 30 | RC7 — PORTC bit 7 |
| دبوس 31 | RC6 — PORTC bit 6 |
| دبوس 32 | RC5 — PORTC bit 5 |
| دبوس 33 | RC4 — PORTC bit 4 |
| دبوس 34 | RC3 — PORTC bit 3 |
| دبوس 35 | RC2 — PORTC bit 2 |
| دبوس 36 | RC1 — PORTC bit 1 |
| دبوس 37 | RC0 — PORTC bit 0 |
| دبوس 38 | RE7 — PORTE bit 7 |
| دبوس 39 | RE6 — PORTE bit 6 |
| دبوس 40 | RE5 — PORTE bit 5 |
| دبوس 41 | RE4 — PORTE bit 4 |
| دبوس 42 | RE3 — PORTE bit 3 |
| دبوس 43 | RE2 — PORTE bit 2 |
| دبوس 44 | RE1 — PORTE bit 1 |
| دبوس 45 | RE0 — PORTE bit 0 |
| دبوس 46 | RA7 — PORTA bit 7 |
| دبوس 47 | RA6 — PORTA bit 6 |
| دبوس 48 | RA5 — PORTA bit 5 |
| دبوس 49 | RA4 — PORTA bit 4 |
| دبوس 50 | RA3 — PORTA bit 3 |
| دبوس 51 | RA2 — PORTA bit 2 |
| دبوس 52 | RA1 — PORTA bit 1 |
| دبوس 53 | RA0 — PORTA bit 0 |
| دبوس 54 | VSS — Digital ground |
| دبوس 55 | VDD — Digital supply voltage (3.3 V) |
| دبوس 56 | VSS — Digital ground |
| دبوس 57 | VDD — Digital supply voltage (3.3 V) |
| دبوس 58 | RF0 — PORTF bit 0 |
| دبوس 59 | RF1 — PORTF bit 1 |
| دبوس 60 | RF2 — PORTF bit 2 |
| دبوس 61 | RF3 — PORTF bit 3 |
| دبوس 62 | RF4 — PORTF bit 4 |
| دبوس 63 | RF5 — PORTF bit 5 |
| دبوس 64 | RH7 — PORTH bit 7 |
| دبوس 65 | RH6 — PORTH bit 6 |
| دبوس 66 | RH5 — PORTH bit 5 |
| دبوس 67 | RH4 — PORTH bit 4 |
| دبوس 68 | RH3 — PORTH bit 3 |
| دبوس 69 | RH2 — PORTH bit 2 |
| دبوس 70 | RH1 — PORTH bit 1 |
| دبوس 71 | RH0 — PORTH bit 0 |
| دبوس 72 | RJ7 — PORTJ bit 7 |
| دبوس 73 | RJ6 — PORTJ bit 6 |
| دبوس 74 | RJ5 — PORTJ bit 5 |
| دبوس 75 | RJ4 — PORTJ bit 4 |
| دبوس 76 | RJ3 — PORTJ bit 3 |
| دبوس 77 | RJ2 — PORTJ bit 2 |
| دبوس 78 | RJ1 — PORTJ bit 1 |
| دبوس 79 | RJ0 — PORTJ bit 0 |
| دبوس 80 | VSS — Digital ground |
| دبوس 81 | VDD — Digital supply voltage (3.3 V) |
| دبوس 82 | TPOUT+ — Ethernet differential transmit output (positive) |
| دبوس 83 | TPOUT- — Ethernet differential transmit output (negative) |
| دبوس 84 | RBIAS — Ethernet PHY bias resistor connection |
| دبوس 85 | VDDRUN — Internal regulator output for Ethernet PHY (3.3 V) |
| دبوس 86 | TPIN+ — Ethernet differential receive input (positive) |
| دبوس 87 | TPIN- — Ethernet differential receive input (negative) |
| دبوس 88 | VSSPLL — PLL ground |
| دبوس 89 | VDDPLL — PLL supply voltage |
| دبوس 90 | OSC1 — Crystal oscillator input |
| دبوس 91 | OSC2 — Crystal oscillator output |
| دبوس 92 | VDD — Digital supply voltage (3.3 V) |
| دبوس 93 | VSS — Digital ground |
| دبوس 94 | RK7 — PORTK bit 7 |
| دبوس 95 | RK6 — PORTK bit 6 |
| دبوس 96 | RK5 — PORTK bit 5 |
| دبوس 97 | RK4 — PORTK bit 4 |
| دبوس 98 | RK3 — PORTK bit 3 |
| دبوس 99 | RK2 — PORTK bit 2 |
| دبوس 100 | RK1 — PORTK bit 1 |
التطبيقات النموذجية
PIC18F97J60-I/PT مناسب لـ 6 التطبيقs: Industrial Ethernet Sensor Node, Building Automation Controller, Web/SCADA Remote Monitor, IoT Ethernet Gateway, Point-of-Sale / Vending Ethernet Bridge, Security / Access Control Panel.
Industrial Ethernet Sensor Node
The PIC18F97J60-I/PT's integrated 10BASE-T MAC/PHY and 128 KB Flash make it ideal for distributed industrial sensor nodes that publish Modbus/TCP or simple HTTP/JSON telemetry. Its 16 MIPS throughput handles both the TCP/IP stack (Microchip MLA, ~8 KB Flash) and the application code (sensor sampling, calibration) within a single chip. The 2.0-3.6 V supply and -40 C to +85 C industrial temperature range cover harsh factory environments, while 70 I/O pins accommodate multiple sensor inputs and digital outputs. Compared to MCU+external-PHY designs, the on-chip PHY removes a major BOM line and simplifies PCB layout.
موصى به
Building Automation Controller
Building automation BACnet/IP and Modbus TCP controllers benefit from the PIC18F97J60-I/PT's integrated Ethernet and 128 KB of program Flash. The on-chip 10-bit ADC scans temperature, humidity, and occupancy sensors while two USART modules interface with legacy RS-485 HVAC equipment. The 70 I/O pins drive relay outputs, triac controls, and indicator LEDs directly without external logic. Per the Microchip datasheet, the industrial temperature range of -40 C to +85 C supports rooftop and mechanical-room installations. The integrated HP Auto-MDIX eliminates crossover cable headaches during commissioning.
موصى به
Web/SCADA Remote Monitor
The PIC18F97J60-I/PT powers compact web-enableable SCADA remote terminal units (RTUs) by running an embedded HTTP server with HTML/JSON status pages and a simple TCP socket listener for SCADA polling. The 128 KB Flash fits both the TCP/IP stack and the application web pages. With 3,808 B RAM and a 200 ns instruction cycle, the part can sustain ~10 simultaneous connections on a 10 Mbps network. The integrated PHY eliminates external magnetics complexity - designers only need the 1:1 transformer and RJ-45 jack.
موصى به
IoT Ethernet Gateway
The PIC18F97J60-I/PT serves as a cost-optimized Ethernet-to-serial/IoT gateway that bridges Wi-Fi-less endpoints to the LAN. Its two USART modules connect to Bluetooth or ZigBee co-processors, while MSSP ports host SPI sensors. The integrated Ethernet peripheral publishes aggregated sensor data over HTTP/MQTT. With 128 KB Flash, the part handles a complete TLS-lite or unsecured MQTT client alongside routing logic. The 3.3 V single-supply operation simplifies power tree design for compact IoT gateway enclosures.
موصى به
Point-of-Sale / Vending Ethernet Bridge
Vending and POS equipment often requires retrofit Ethernet for inventory telemetry without redesigning the host controller. The PIC18F97J60-I/PT acts as a co-processor that translates legacy RS-232/RS-485 POS traffic onto Ethernet (EtherNet/IP, TCP socket). Its 128 KB Flash stores a vendor-specific protocol stack, while the integrated 10 Mbps Ethernet handles backhaul traffic. The industrial temperature grade and 2.0-3.6 V supply fit unattended kiosk environments with wide temperature swings and battery-backed 3.3 V rails.
موصى به
Security / Access Control Panel
Access control panels using the PIC18F97J60-I/PT leverage its 70 I/O pins for Wiegand readers, door strikes, REX sensors, and status LEDs while publishing events to a centralized access control server over Ethernet. The integrated 10BASE-T PHY supports PoE-style deployments with the addition of a passive splitter, and 128 KB Flash fits TLS handshake and credential caching logic. The -40 C to +85 C operating range covers outdoor gate controllers, while the integrated PHY enables real-time door status updates with sub-second latency over the LAN.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PIC18F97J60-I/PT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | PIC18F97J60T-I/PT | PIC18F96J60-I/PT | PIC18F87J60-I/PT | PIC18F96J94-I/PF |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PT) | 100-pin TQFP (PT) | 100-pin TQFP (PT) | 80-pin TQFP (PT) | 100-pin TQFP (PF) |
| Flash Memory | 128 KB | 128 KB | 64 KB | 128 KB | 64 KB |
| Max CPU Frequency | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) |
| Integrated Ethernet PHY | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | No (MAC only, external PHY required) |
| Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Approx. Unit Price (qty 1, USD) | $11.83 | ~$11.83 | ~$10.50 | ~$11.50 | ~$13.20 |
أبرز الفروقات
- Integrated 10BASE-T MAC + PHY on a single 8-bit MCU die (مقابلPIC18F97J94-I/PF)
- Double the Flash memory versus PIC18F96J60 sibling (مقابلPIC18F96J60-I/PT)
- Highest I/O count in the PIC18F97J60 family (مقابلPIC18F87J60-I/PT)
- Industrial temperature grade -40 C to +85 C in 100-pin TQFP (مقابلPIC18F96J60-I/PF (100-pin TQFP, PF suffix))
ملاحظات التصميم
The integrated 10BASE-T Ethernet PHY is highly sensitive to PCB layout. Use a 4-layer board with a continuous ground plane beneath the Ethernet signal traces. The TPOUT+/TPOUT- and TPIN+/TPIN- pairs must be routed as 100-ohm differential pairs with matched lengths within 2 mm. Keep the RBIAS resistor within 5 mm of pin 84 and the VDDRUN/VDDPLL decoupling caps within 3 mm of their respective pins. Reference Microchip AN1120 for the recommended magnetics and RJ-45 jack selection.
The PIC18F97J60-I/PT has multiple VDD/VSS pins that must all be connected and bypassed. Place a 0.1 uF ceramic capacitor close to each VDD/VSS pair, and add a bulk 10 uF tantalum or ceramic capacitor near the package. The internal 3.3 V regulator requires a 4.7 uF low-ESR capacitor on VDDRUN (pin 85) and VDDPLL (pin 89) for stable operation. Without proper bypassing, the Ethernet PHY will exhibit high bit-error rates or link failure.
Crystal placement is critical for the Ethernet MAC. The 25 MHz or 41.667 MHz crystal (per oscillator configuration) should be placed within 10 mm of pins 90/91 with short, symmetric traces and a guard ground ring. Avoid routing any switching signals (PWM, digital outputs) near the crystal traces or the Ethernet differential pairs. The MCLR pin should have a 10 kohm pull-up to VDD and a 100 nF cap to ground for in-circuit serial programming (ICSP) reliability.
Do not assume the 128 KB Flash is fully available for application code - the TCP/IP stack (MLA or Harmony-based) consumes 8-15 KB. Reserve at least one Flash erase page (1024 bytes) for EEPROM emulation and at least 4 KB for bootloader/field-update capability. The Ethernet MAC requires a unique 48-bit MAC address; design in a MAC address EEPROM like 25AA02E48 to avoid hard-coding addresses per unit.
Although the Ethernet PHY is integrated, the TPOUT+/- signals still pass through external 1:1 isolation transformers before the RJ-45 connector. Choose a transformer with integrated common-mode chokes (e.g., Pulse H1102 or equivalent) to meet IEEE 802.3 emissions requirements. The center tap of the transmit transformer should connect to VDDRUN, and the receive center tap should connect to a quiet 3.3 V supply via a ferrite bead - this improves EMI performance significantly.
معلومات الامتثال
RoHS and REACH compliant per Microchip product declaration. Lead-free TQFP (PT) termination. Industrial temperature grade -40 C to +85 C. AEC-Q100 not applicable - this is a microcontroller, not an automotive-grade IC; designers needing AEC-Q100 should consider PIC18F67J60-I/PT automotive variants or PIC32MX equivalents.
