SN74AC240N - 8-Channel 3-State Inverter | Texas Instruments
MPN: SN74AC240N ✓ نشطSN74AC240N نظرة عامة
An octal buffer/line driver is a logic IC used to increase drive strength and isolate a data bus from the load presented by downstream inputs. A three-state output can actively drive a logic level, remain at high impedance, or be placed in the high-impedance state by its output-enable input. This family belongs to the CMOS logic hierarchy, where AC-series devices operate from a 2 V to 6 V supply and are designed for low-voltage digital systems requiring buffered bus signals.
The SN74AC240N provides eight inverting channels and separate controls for two four-channel output groups. Its principal features are the 2 V to 6 V operating range, eight channels, three-state output capability, and separate output enables. These characteristics make it useful when a system needs controlled bus isolation, increased source current for lightly loaded interconnects, or a defined way to disconnect portions of a bidirectional bus during a shared-bus architecture.
Each output section combines an input buffer with an output driver capable of assuming a high-impedance state when its associated output-enable input is inactive. The two four-channel groups can be enabled independently, which supports segmented bus control. Because the outputs are inverting, system logic must account for reversed polarity at every driven signal. A three-state output does not actively hold the bus at a valid level while disabled; the receiving system must provide suitable pull-up or pull-down behavior when another device can drive that net.
Typical uses include memory address buffering, clock distribution, bus-oriented receivers and transmitters, control-signal isolation, and industrial digital interfaces. The part is also suitable when several compatible devices share a common data path and only selected groups should drive it at a given time. Independent output-enable control simplifies arbitration, test access, and expansion of a shared bus.
PCB design should keep the 20-pin PDIP footprint free of unintended shorts and route high-speed or noise-sensitive nets away from supply and return-current paths. Input and output-enable signals should have defined levels at every operating state, including power-up. Designers should also verify that all devices connected to a shared bus have compatible voltage levels and that their output-enable controls cannot overlap in an unintended drive condition.
This product overview combines the device function, package, supply range, and bus-driver use cases with practical guidance for output-state control, polarity, and shared-bus implementation. It also organizes drop-in replacement information and engineering-oriented comparisons to support component selection before PCB release.
بدائل مباشرة لـ SN74AC240N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
MC74AC240NG
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
CD74AC240E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
CD74AC240EE4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74AC240N الحدود القصوى والخصائص الكهربائية
| Product Type | Octal inverting buffer/line driver with three-state outputs |
| Number of Channels | 8 channels |
| Channel Organization | 2 groups of 4 channels |
| Output Polarity | Inverting |
| Output State | Three-state, including high-impedance |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable Control | Separate control for each 4-channel group |
| العلبة | 20-pin PDIP |
| نوع التركيب | Through-hole |
| Logic Family | AC CMOS |
| Number of Inputs | 8 data inputs and 2 output-enable inputs |
| عدد المخارج | 8 three-state outputs |
دليل تكوين أطراف SN74AC240N 20-pin pdip
تكوين الأطراف لـ SN74AC240N (حزمة 20-pin pdip). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74AC240N.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74AC240N مناسب لـ 6 التطبيقs: Memory Address Buffering, Clock Signal Distribution, Shared Bus Isolation, Control Signal Isolation, Industrial Digital Interface, Test and Measurement Logic.
Memory Address Buffering
The SN74AC240N is suitable for buffering memory-address signals because it provides eight inverting channels, a 2 V to 6 V supply range, and three-state outputs in a 20-pin PDIP package. Two independently controlled four-channel groups can drive address-related sections selectively, reducing loading on the originating logic. The inverting polarity must be reflected in address decoding or corrected upstream. Because a disabled output becomes high impedance, the connected memory bus should include suitable pull-up or pull-down arrangements so its inactive level remains defined.
موصى به
Clock Signal Distribution
The SN74AC240N can distribute clock signals to multiple logic destinations when isolation and controlled bus participation are important. Its eight inverting three-state outputs and two separate output-enable groups support segmented clock routing, while the 2 V to 6 V operating range matches low-voltage CMOS systems. Because each output reverses polarity, the receiving clock domain must tolerate the inverted transition. Timing margin should be evaluated at the system level, particularly when several clocked devices are connected to the driven net.
موصى به
Shared Bus Isolation
The SN74AC240N is useful on a shared bus where multiple devices must connect without driving the same net simultaneously. Eight three-state outputs reduce the risk of contention when the two output-enable groups are controlled separately, and the device operates across a 2 V to 6 V supply range. The design must guarantee exclusive drive ownership in every operating state, including reset and power-up. Pull resistors or another valid biasing method should keep disabled bus nets from floating.
موصى به
Control Signal Isolation
The SN74AC240N can isolate groups of control signals between logic sections while providing stronger drive than a direct source-to-load connection. Its two four-channel groups can be enabled independently, allowing one control group to remain active while another is disconnected. Since every channel is inverting, system logic must account for reversed control polarity. The 20-pin PDIP format also supports straightforward through-hole assembly and prototype rework compared with a fine-pitch surface-mount implementation.
موصى به
Industrial Digital Interface
The SN74AC240N fits low-voltage industrial control logic that requires buffered digital outputs and controlled bus connection. Its eight three-state channels provide flexibility for separating command, status, or inter-board signals, while the 2 V to 6 V range supports common low-voltage CMOS rails. The implementation must account for inverted logic and cannot rely on a disabled output to establish a valid high or low level. Firmware and hardware should ensure that output-enable outputs never allow conflicting devices to drive one bus simultaneously.
موصى به
Test and Measurement Logic
The SN74AC240N can serve as a controllable signal-buffer element in test and measurement systems where selected outputs must drive fixtures while others remain disconnected. The two independently enabled output groups simplify segmented test-bus control, and the eight inverting channels provide consistent signal conditioning at a 2 V to 6 V supply. Inverting behavior must be included in the test-vector design. The output-enable timing and propagation delay should also be evaluated to ensure the selected group enters or leaves the drive state within the instrument's acquisition window.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74AC240N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MC74AC240NG | CD74AC240E | CD74AC240EE4 |
|---|---|---|---|---|
| Package | 20-PDIP | 20-PDIP | 20-PDIP | 20-PDIP |
| Brand | Texas Instruments | Motorola | Texas Instruments | Texas Instruments |
| Channel Count | 8 channels | 8 channels | 8 channels | 8 channels |
| Output Polarity | Inverting | Inverting | Inverting | Inverting |
| Output State | Three-state | Three-state | Three-state | Three-state |
| Output Group Organization | Two groups of 4 channels | Two groups of 4 channels | Two groups of 4 channels | Two groups of 4 channels |
| Output Enable Control | Separate control for each 4-channel group | Separate control for each 4-channel group | Separate control for each 4-channel group | Separate control for each 4-channel group |
| Technology Family | AC CMOS | AC CMOS | AC CMOS | AC CMOS |
أبرز الفروقات
- Provides two independently controlled groups within one octal package (مقابلCD74AC240E)
- Combines inverting three-state buffering with a 2 V to 6 V operating range (مقابلMC74AC240NG)
- Uses a readily handled 20-pin PDIP footprint (مقابلCD74AC240EE4)
ملاحظات التصميم
Account for the inversion of every SN74AC240N data channel when defining control equations, address maps, or test vectors. Also distinguish an inactive output-enable input from a valid logic-low output: the disabled outputs enter a high-impedance state rather than actively driving a low level. Add suitable pull-up or pull-down resistors wherever a disabled shared-bus net must remain in a defined state.
Operate the SN74AC240N only within its 2 V to 6 V supply range and use a supply whose ground reference is common with every device connected to the same bus. Review the datasheet's input and output current limits before adding load capacitance or long interconnects. The component is a digital buffer rather than a power regulator, so supply decoupling and trace-current capacity should be handled by the board-level power design.
Place the logic source close to the relevant SN74AC240N input and keep the driven output path away from adjacent high-speed or switching nodes. Use a continuous ground-plane reference beneath the 20-pin PDIP footprint and avoid routing shared-bus traces beneath long power-conversion sections. Where multiple devices can connect to one net, review their physical proximity and enable-state sequencing to reduce simultaneous switching and contention risk.
Treat the two output-enable groups as independent bus-ownership controls and define their states during reset, power-up, and power-down. The system must prevent two drivers from actively opposing the same net. For long or lightly terminated lines, evaluate propagation delay, edge behavior, capacitive loading, and the receiver's threshold in the manufacturer datasheet before treating the buffered output as a guaranteed solution for high-speed communications.
معلومات الامتثال
The Texas Instruments product page identifies the SN74AC240 as a logic IC rather than an automotive-qualified device. Detailed RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations must be confirmed for the exact ordering code.