SN74LS07NS - 6-Channel Open-Collector Buffer | Texas Instruments
MPN: SN74LS07NS ✓ نشطSN74LS07NS نظرة عامة
A logic buffer or driver is a digital IC that conditions and strengthens a signal so it can reliably drive another logic circuit. The SN74LS07 belongs to the 74-series bipolar logic hierarchy, where a buffer or driver sits between digital logic ICs and external loads. Its open-collector outputs require an external pull-up resistor, allowing the output stage to disconnect electrically when the output is low.
Key features include six non-inverting channels, open-collector output design, a 4.75 V to 5.25 V supply range, 40 mA sink-current capability, 14 mA quiescent current, and approximately 45 mA operating supply current. The open-collector architecture is useful when multiple compatible outputs must share a wired bus or when an interface requires an externally selected pull-up voltage. The SN74LS07NS commercial temperature range is 0°C to 70°C.
The bipolar SN74LS07 architecture is intended for conventional 5 V TTL systems rather than low-voltage CMOS designs. Because each output has an open-collector transistor rather than a totem-pole output stage, the board designer selects the pull-up resistor and determines the usable rise time from the bus capacitance. Input and output logic levels follow the SN74LS07 family specifications, while the low-level output current is specified at 40 mA.
Typical uses include driving indicator lamps, relay interfaces, optocoupler inputs, level-shifting networks, and general-purpose open-collector digital buses. The SN74LS07NS is particularly appropriate when the driven device must share a pull-up rail or when a wired-AND/open-collector connection is required. It can also buffer TTL signals for short interconnect distances within a 5 V system.
Choose the pull-up resistor and trace length together because the external resistor and total bus capacitance determine the output rise time. Keep the pull-up connection short, use a resistor value suitable for the required sink current, and account for the 40 mA output rating when calculating the worst-case low-state load. The open-collector output can remain off during reset or power-loss conditions, which may be beneficial in fail-safe interface arrangements.
This product page combines the SN74LS07NS electrical characteristics, package details, pin-compatible alternatives, pricing evidence, and practical design guidance into an engineering-focused reference for selecting and implementing this six-channel open-collector buffer.
بدائل مباشرة لـ SN74LS07NS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع SN74LS07NS (نفس عامل الشكل والبصمة) — يختلف في Logic Family, Number of Channels, Package.
SN74LS07DR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←SN74ALS07ADR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
SN74HC07DR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
SN74HCT07DR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LVC07ADR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS07NS الحدود القصوى والخصائص الكهربائية
| Logic Type | TTL |
| Number of Channels | 6 channels |
| Elements per Channel | 1 element |
| نوع الخرج | Open-collector |
| Polarity | Non-inverting |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Low-Level Output Current | 40 mA |
| تيار السكون | 14 mA |
| Operating Supply Current | 45 mA |
| Minimum Operating Temperature | 0°C |
| Maximum Operating Temperature | 70°C |
| العلبة | 14-SO (SOIC-14) |
| نوع التركيب | Surface mount |
| Logic Family | SN74LS |
دليل تكوين أطراف SN74LS07NS 14-so (soic-14)
تكوين الأطراف لـ SN74LS07NS (حزمة 14-so (soic-14)). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS07NS.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74LS07NS مناسب لـ 6 التطبيقs: Open-Collector Indicator Driving, Relay and Solenoid Interface, Open-Collector Level Shifting, Optocoupler Input Buffering, Wired Open-Collector Data Bus, Legacy TTL Signal Conditioning.
Open-Collector Indicator Driving
The SN74LS07NS fits indicator-driving circuits that require one shared pull-up rail and independent low-side sinking paths. Each of its six channels provides non-inverting control and a 40 mA low-level output-current rating. Connect the selected channel output to the indicator cathode, connect the indicator anode to the chosen pull-up rail, and place a suitable resistor in the pull-up path. This arrangement allows the device to serve indicators using a voltage other than the IC's 5 V logic rail. Check the pull-up current against the 40 mA limit and account for the SN74LS07NS 0°C to 70°C commercial operating range.
موصى به
Relay and Solenoid Interface
The SN74LS07NS can provide the low-side sinking element in a relay-driver stage because each open-collector output is rated for 40 mA of low-level current. The logic output energizes a suitable transistor or relay coil, while a flyback diode or other suppression component handles inductive current when the driver switches off. The SN74LS07NS should not drive a coil directly unless the coil current, voltage, temperature rise, and waveform remain within every applicable device limit. Since the buffer is non-inverting, the system must account for the active-low behavior created by the open-collector sinking stage.
موصى به
Open-Collector Level Shifting
The SN74LS07NS supports unidirectional level shifting when the source and destination share a suitable pull-up rail. Its six non-inverting channels accept 5 V TTL logic, and each open-collector output connects to a pull-up that establishes the receiving-side high voltage. This arrangement is particularly useful for isolated or externally biased signal domains, provided the pull-up voltage remains within the output-device limits. The SN74LS07NS 4.75 V to 5.25 V supply range and 40 mA sink rating must be considered when choosing the pull-up. Because the output is not actively driven high, rise time also depends on the pull-up resistance and total load capacitance.
موصى به
Optocoupler Input Buffering
The SN74LS07NS can sink the current from an optocoupler or phototransistor input while the pull-up resistor establishes the digital high level. This arrangement turns the phototransistor's changing resistance into a clean logic signal at a 5 V TTL receiver. Select the pull-up so the low-state current remains below the 40 mA channel rating and so the resistor provides adequate noise margin and rise-time performance. The buffer adds electrical drive and isolation from the phototransistor network, but it does not improve the optical signal itself. Validate the operating-temperature range because this SN74LS07NS orderable is specified for 0°C to 70°C.
موصى به
Wired Open-Collector Data Bus
The SN74LS07NS can participate in a wired open-collector bus because its output channels release the shared line instead of actively driving it high. Any channel that pulls the line low determines the low state, while the common pull-up creates the high state when all channels are off. This behavior supports simple arbitration and fault-tolerant interfaces in conventional 5 V TTL equipment. The design must include a pull-up resistor sized for the total bus capacitance and low-state sink current, and it must account for the resulting rise time. The 40 mA low-level output current defines the channel's principal loading constraint.
موصى به
Legacy TTL Signal Conditioning
The SN74LS07NS provides six non-inverting channels for strengthening conventional TTL signals and isolating a logic source from a driven net. The six-channel organization allows one package to serve several control or status signals, while the open-collector outputs add flexibility for pull-up-based interfaces. A 4.75 V to 5.25 V supply is required, and the device's 45 mA operating supply current should be included in the power-budget calculation. For legacy equipment, the 0°C to 70°C operating range and 40 mA low-level output rating are the principal selection boundaries. Confirm output timing and logic thresholds during system qualification.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS07NS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SN74LS07DR | SN74ALS07ADR | SN74HC07DR | SN74HCT07DR | SN74LVC07ADR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-14 | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same |
| Number of Channels | 6 | 6 | 6 | 6 | 6 | 6 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.5 V to 5.5 V | 2 V to 6 V | 4.5 V to 5.5 V | 1.65 V to 5.5 V |
| Logic Family | SN74LS bipolar TTL | SN74LS bipolar TTL | SN74ALS advanced bipolar TTL | SN74HC CMOS | SN74HCT CMOS with TTL-compatible inputs | SN74LVC low-voltage CMOS |
أبرز الفروقات
- Direct same-function SOIC alternative (مقابلSN74LS07DR)
- Broad supply-voltage operating range (مقابلSN74HC07DR)
- Lower-voltage compatibility (مقابلSN74LVC07ADR)
- TTL-compatible input thresholds (مقابلSN74HCT07DR)
ملاحظات التصميم
Select an external pull-up resistor for every open-collector output. Its value must satisfy the required low-level sink current, remain within the SN74LS07NS 40 mA output rating, and provide an acceptable rising edge when combined with total bus capacitance. A lower pull-up resistance improves rise time but increases current and power dissipation; a higher value reduces loading but can make the interface too slow. Validate both worst-case bus loading and the longest connected trace.
Place each pull-up resistor close to the corresponding SN74LS07NS output or the controlled bus node when several outputs share a bus. Keep the connection short to limit parasitic capacitance and susceptibility to noise. Route open-collector lines away from sensitive clock and analog nodes, provide a continuous ground reference, and place the device's decoupling capacitor close to its supply pin according to the manufacturer pinout and recommended layout guidance.
Do not treat the open-collector high state as an actively driven logic-high output. If the pull-up is omitted, the output remains floating; if the pull-up rail exceeds the device's permitted voltage range, the output can be damaged. Also avoid confusing the SN74LS07NS SOIC ordering suffix with the SN74LS07N 14-PDIP version. Confirm the PCB footprint, package drawing, pin numbering, temperature grade, and pull-up voltage before releasing production artwork.
معلومات الامتثال
The Texas Instruments product page provides device, ordering, and quality information, but the verified records do not explicitly state the requested compliance status values. Compliance documents should be reviewed before procurement.