SN74LS624N - Dual 20MHz VCO IC | Texas Instruments | 14-PDIP
MPN: SN74LS624N ✓ نشطSN74LS624N نظرة عامة
A voltage-controlled oscillator is a frequency-generating circuit whose operating frequency is adjusted by an external control voltage. The SN74LS624N contains two VCO sections, allowing one package to support two related timing functions. This dual-channel architecture can reduce component count in circuits requiring paired modulation, clock synthesis, or fixed-offset frequency generation. Its 14-pin PDIP package also makes it practical for prototyping, educational equipment, repair work, and through-hole industrial assemblies.
According to the Texas Instruments product information, the SN74LS624 is a voltage-controlled oscillator with an operating frequency range identified as 1.1 MHz to 25 MHz in the cited technical summary. The SN74LS624N ordering designation is also described as a 20 MHz VCO in 14-pin PDIP format by distributor product records. These descriptions indicate wide-range frequency generation with externally determined timing and control characteristics.
The SN74LS624 family is associated with improved voltage-to-frequency linearity, a broad frequency range, and compensation features. Each oscillator uses external timing components in combination with voltage-sensitive frequency-control inputs, allowing the circuit designer to establish center frequency and modulation range through component selection and control-voltage design. The control input impedance, recommended external timing network, and recommended decoupling arrangement should follow the manufacturer datasheet when evaluating a specific operating point.
Typical uses include variable-frequency clock generation, tone and alarm generation, modulation circuits, frequency dividers, and phase-locked-loop signal chains. The dual oscillator sections are also useful in test equipment where two related but independently adjustable waveforms are required. Because the output frequency is influenced by component tolerances and control-voltage accuracy, stable external timing components and careful routing of the control signals are important for repeatable results.
Designers should treat the control-voltage path as a sensitive analog signal. Keep the timing components close to the device, minimize loop area around the oscillator nodes, and provide the supply and bypass decoupling specified by the Texas Instruments datasheet. Before substituting the device into an existing circuit, verify the external timing network, control-voltage range, output waveform, and package pin assignments rather than relying only on the oscillator function.
This product page combines the SN74LS624N ordering information, VCO frequency characteristics, package details, practical design guidance, and verified replacement research. It is intended to help engineers identify the correct dual voltage-controlled oscillator, locate the official datasheet, assess stock through a quotation request, and determine whether a documented same-footprint alternative is appropriate for the intended design.
بدائل مباشرة لـ SN74LS624N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
SN74LS624NE4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS624N المواصفات
| Product Type | Dual voltage-controlled oscillator (VCO) |
| Logic Family | 74LS |
| Number of Oscillator Channels | 2 channels |
| Distributor Maximum Frequency Rating | 20 MHz |
| Technical Summary Frequency Range | 1.1 MHz to 25 MHz |
| جهد التغذية | 5 V |
| Output Waveform | Square wave |
| Duty Cycle | 50% |
| Total Input Capacitance | 45 pF |
| Package Type | 14-pin PDIP |
| نوع التركيب | Through-hole |
| Pitch | 7.62 mm |
| Body Width | 0.300 inch |
| Operating Voltage | 5 V |
| Control Method | External voltage control |
| Frequency Setting | External capacitor or crystal |
| تكوين الخرج | Dual oscillator output |
دليل تكوين أطراف SN74LS624N 14-pin pdip
تكوين الأطراف لـ SN74LS624N (حزمة 14-pin pdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS624N.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74LS624N مناسب لـ 6 التطبيقs: Variable-Frequency Clock Generation, Tone Generation and Alarm Systems, Phase-Locked-Loop Timing, Frequency Modulation and Sweep Control, Instrumentation and Signal Generators, Industrial Control and Legacy Equipment Repair.
Variable-Frequency Clock Generation
The SN74LS624N fits clock-generation designs requiring a square-wave output whose frequency can be varied by a control voltage. Its distributor-listed 20 MHz rating and external timing architecture allow the designer to select a capacitor or crystal network and then modulate the operating point through the control input. The dual VCO configuration can also generate two related clock signals. Confirm the timing-component range and control-voltage limits against the manufacturer characteristic curves, and route the control node away from high-current switching paths to preserve frequency stability.
موصى به
Tone Generation and Alarm Systems
The SN74LS624N can generate a variable-frequency square-wave tone for alarms, test tones, and simple audio-style signaling systems. One oscillator channel may provide the tone while the second can provide a related reference or auxiliary frequency, reducing package count compared with two discrete single VCOs. Because the square-wave output is rich in harmonics, filtering may be needed for low-distortion audio. Set the timing network using the TI recommendations and validate frequency tolerance across temperature and the intended control-voltage range.
موصى به
Phase-Locked-Loop Timing
The SN74LS624N is suitable for the oscillator element of a phase-locked-loop timing system where an external loop filter and phase comparator establish regulation around the VCO's control voltage. Its two oscillator sections can support a main reference loop and a secondary related frequency path. The manufacturer describes improved voltage-to-frequency linearity, range, and compensation for this oscillator family. Verify loop stability, capture range, and component tolerances in the actual PLL topology rather than relying on the oscillator's standalone frequency range alone.
موصى به
Frequency Modulation and Sweep Control
The voltage-controlled input lets the SN74LS624N support frequency sweeps, modulation, and closed-loop tuning when a control system varies its input voltage. A single external timing component establishes the nominal range, while the control voltage moves the oscillator within the range supported by the manufacturer characteristic curves. Keep the modulation source impedance and leakage in view because they directly affect frequency linearity and noise. For precise results, characterize the complete control path and timing-component tolerance across the required environmental range.
موصى به
Instrumentation and Signal Generators
The SN74LS624N can serve as the programmable timing source in bench instruments, function generators, and automated test equipment requiring repeatable square-wave outputs. Its dual channels allow one device to provide a stimulus and a related reference signal, while the external timing network supports application-specific frequency selection. A controlled 5 V supply and stable decoupling are important when minimizing frequency jitter. Use the manufacturer's output and control-voltage data to establish rise-time, duty-cycle, and modulation limits.
موصى به
Industrial Control and Legacy Equipment Repair
The 14-pin PDIP package and through-hole construction make the SN74LS624N useful for maintaining older industrial control, test, and laboratory equipment that originally used this dual VCO. A legacy repair can retain the original board footprint and signal topology when the replacement has verified electrical and timing compatibility. Confirm the exact suffix, temperature grade, and lifecycle status before procurement. Where no documented same-footprint part is available, avoid installing CD4046 or 74HC4046 devices directly because their pin arrangements and supply requirements differ.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS624N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SN74LS624NE4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 14-pin PDIP | 14-pin PDIP |
| Product Type | Dual voltage-controlled oscillator | Dual voltage-controlled oscillator |
| Number of Oscillator Channels | 2 | 2 |
أبرز الفروقات
- Two VCO channels in one package (مقابلCD4046)
- Established 14-pin PDIP option for legacy through-hole boards (مقابل74HC4046)
- Documented same-family ordering option (مقابلSN74LS624NE4)
ملاحظات التصميم
Place the external timing components close to their associated SN74LS624N pins and minimize the loop area around each oscillator node. Long PCB traces add parasitic capacitance that can shift the operating frequency and alter control-voltage linearity. Keep the timing network away from switching-node return currents, and follow the physical arrangement in the Texas Instruments datasheet when reproducing the manufacturer's recommended application circuit.
Do not treat CD4046, 74HC4046, NE566, or LM566 devices as direct SN74LS624N replacements. Although they implement related voltage-controlled oscillator functions, the verified material does not establish a shared 14-pin footprint or identical pin map. A new design may use one of those families after a circuit redesign, but an existing PCB should retain the Texas Instruments device unless a documented pin-to-pin cross-reference is available.
Treat the control-voltage connection as a sensitive timing signal rather than a general-purpose logic input. Keep its source impedance low, terminate it according to the oscillator control circuit, and isolate it from noisy switching paths and high-impedance leakage nodes. Recheck center frequency, modulation range, and duty cycle at the intended supply voltage and temperature because timing components and control-network error can move the oscillator away from its nominal point.
Use the supply voltage and decoupling arrangement specified by the manufacturer datasheet, and include adequate bypass capacitance at the device. Supply ripple and ground-return coupling can appear as frequency instability or jitter even when the nominal control voltage is correct. During repair or board conversion, compare the original circuit's grounding and decoupling with the TI recommended application diagram rather than copying a generic oscillator layout.
معلومات الامتثال
The verified excerpts identify the Texas Instruments SN74LS624 voltage-controlled oscillator family but do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable because this is a logic and timing IC rather than an automotive-qualified power device.