Texas Instruments

SN74LS645H - Octal Bus Transceiver | Texas Instruments

MPN: SN74LS645H ✓ نشط
الحد الأدنى للطلب: 1 |

SN74LS645H نظرة عامة

Texas Instruments SN74LS645H is an octal bus transceiver designed for asynchronous two-way communication between data buses. The device provides eight parallel data channels, non-inverting transceiver operation, and three-state output control. It is intended for systems in which two bus masters, processors, peripheral devices, or memory devices must exchange data over a shared bus.

A bus transceiver is a bidirectional interface IC that combines driver and receiver functions. It allows a device to transmit logic levels onto a bus and receive logic levels from that same bus. The SN74LS645 family reduces the number of external timing requirements by coordinating bus direction and output-enable control, while the three-state outputs permit multiple devices to share common data lines without driving them simultaneously.

The SN74LS645 is one member of the SN54LS and SN74LS low-power Schottky TTL logic families. Low-power Schottky TTL combines bipolar transistor logic with Schottky-clamped input stages. This technology is associated with the 74LS family’s established logic levels, system design heritage, and broad use in legacy digital equipment. The octal organization means that one device handles eight signal lines in parallel rather than requiring eight separate single-bit interface circuits.

The H suffix identifies the orderable SN74LS645H configuration listed for the octal bus transceiver family. The manufacturer product page and supporting technical descriptions identify the device as an octal transceiver for asynchronous two-way bus communication. Detailed electrical limits, propagation timing, supply-current behavior, temperature grade, and package dimensions should be confirmed in the manufacturer datasheet before release to production.

Typical uses include bidirectional processor and peripheral buses, memory-interface buffering, data acquisition systems, test equipment, industrial control logic, and repairs of legacy TTL-based hardware. The device is especially useful where a shared bus requires controllable drive direction and a high-impedance state so that only one participant actively drives the lines during a given transaction.

Designers should verify direction and enable truth tables, propagation delay, setup and hold timing, input and output loading, and the available input-to-output voltage margin in the system. A shared bus also requires a defined arbitration method so that no two drivers enable the same line simultaneously. Decoupling and signal-return paths should follow the recommended layout in the manufacturer documentation.

This page combines the official product identity with package-oriented sourcing context, replacement guidance, application patterns, and design cautions. The comparisons emphasize electrical and functional interchangeability rather than treating every similarly named 74-series component as a safe substitute. Verify timing and logic behavior on the target board, especially when replacing a component across manufacturers or between commercial and extended-temperature variants.

بدائل مباشرة لـ SN74LS645H — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع SN74LS645H (نفس عامل الشكل والبصمة) — يختلف في Logic Family, Output State.

Texas Instruments
Logic Family: 74LS bipolar TTL
Output State: 3-state
قارن مع SN74LS645H →

SN74LS645N

✅ بديل مباشر
Texas Instruments
📦 20-PDIP
Octal bus transceiver · 74LS bipolar TTL · 1 element · 8 bits · Non-inverting · 3-state · 4.75 V to 5.25 V · Schmitt trigger

تواصل لمعرفة السعر

عرض ورقة البيانات ←

SN74LS645H الحدود القصوى والخصائص الكهربائية

Device Type Octal bus transceiver
Number of Data Channels 8 channels
Bus Communication Mode Asynchronous two-way communication
Logic Family 74LS low-power Schottky TTL
Signal Polarity Non-inverting
Output State Three-state output
حالة RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

دليل تكوين أطراف SN74LS645H standard

تكوين الأطراف لـ SN74LS645H (حزمة standard). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.

مخطط توزيع أطراف حزمة standard لـ SN74LS645H

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS645H.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

SN74LS645H مناسب لـ 6 التطبيقs: Bidirectional Processor Bus Buffering, Shared Peripheral Data Bus, Memory Interface Buffering, Data Acquisition Backplane, Industrial Control Data Exchange, Legacy Test Equipment Interface.

🔧

Bidirectional Processor Bus Buffering

The SN74LS645H is appropriate for an eight-bit processor bus that must exchange data with slower peripheral devices. Its eight parallel channels reduce the number of interface devices required, while the three-state outputs allow the processor side to relinquish the bus when another participant transmits. The octal architecture follows the data width and control structure common in legacy TTL systems. Before implementation, verify direction and enable truth tables, propagation delay, setup and hold timing, and the capacitive and DC loading contributed by every connected device.

🏭

Shared Peripheral Data Bus

In a shared peripheral bus, several devices may communicate over the same eight conductors without driving them at the same time. The SN74LS645H supports this arrangement through three-state outputs, non-inverting data transfer, and separate control functions for bus direction and output enable. That structure lets an active transmitter drive valid levels while other participants remain isolated. A practical design should include arbitration or an enable discipline, logic-state analysis during transitions, and checks of receiver thresholds and timing margins against the slowest peripheral.

🖥️

Memory Interface Buffering

The SN74LS645H can buffer asynchronous data paths between a memory device and a legacy system bus. Eight parallel channels match an eight-bit memory organization, and the high-impedance output state allows the transceiver to isolate itself when another bus master uses shared address or data routing. Because the SN74LS645 is a transceiver rather than a dedicated memory controller, the system must define read and write direction, control chip-select behavior, and bus ownership. Timing should be validated against both memory access requirements and transceiver propagation delay.

📡

Data Acquisition Backplane

An eight-channel data-acquisition backplane can use the SN74LS645H to distribute command and return data between a controller and modular measurement circuits. The non-inverting, three-state interface keeps the logic behavior compatible with traditional TTL buses while allowing inactive modules to avoid contention. Use the device where each module has a clearly defined enable interval and the bus remains within the family’s specified loading and timing limits. For sensitive analog measurement systems, evaluate ground offsets, bus noise, and supply decoupling separately from the digital transceiver function.

🏭

Industrial Control Data Exchange

The SN74LS645H is suitable for exchanging eight-bit control and status information between legacy industrial controller cards. Its three-state outputs support shared wiring when modules enter inactive states, while non-inverting operation simplifies compatibility with existing TTL data conventions. Industrial implementation should confirm operating-temperature limits, noise margins, isolation strategy, and connector or cable loading before deployment. The bus enable logic must prevent simultaneous activation, and the controller should retain the ability to reset or disable all drivers during fault conditions.

🔧

Legacy Test Equipment Interface

The SN74LS645H can connect a controller to legacy test and measurement equipment that uses an asynchronous eight-bit bus. The transceiver provides a convenient way to place high-impedance isolation between equipment sections and to support controlled direction changes during transfers. Compatibility depends on matching voltage levels, input thresholds, output drive, propagation delay, and connector timing at the far end of the bus. Use this approach for repair and expansion of established TTL systems rather than designing new high-speed fabrics around a legacy-family device.

What is the SN74LS645H?
The SN74LS645H is an octal bus transceiver for asynchronous two-way communication between data buses. According to the Texas Instruments SN74LS645 product documentation, it provides eight parallel channels with non-inverting operation and three-state outputs. The device combines transmit and receive paths on common bus lines, making it suitable for bidirectional communication between processors, peripherals, memory devices, and other bus participants.
How many bus lines can the SN74LS645H handle?
The SN74LS645H handles eight parallel bus lines in one package. The “octal” designation means that the transceiver contains eight corresponding data channels rather than one or two isolated channels. According to the manufacturer description, these channels support asynchronous two-way communication, while the three-state output control allows unused drivers to present a high-impedance state during another bus device transmits.
What does three-state output mean for the SN74LS645H?
Three-state output means each driver can operate as a logic high, a logic low, or a high-impedance state. This capability is essential on a shared bidirectional bus because all connected transmitters must not actively drive the same line simultaneously. The Texas Instruments SN74LS645 documentation identifies the SN74LS645 as an octal bus transceiver with three-state output, allowing bus participants to be isolated when they are not driving data.
Where can I download the SN74LS645H datasheet PDF?
The official SN74LS645 documentation is available through the Texas Instruments product page at https://www.ti.com/product/SN74LS645. Use the datasheet link on that page for the manufacturer-controlled PDF and ordering information. The product page identifies the device as an octal bus transceiver, while historical documentation also describes asynchronous two-way bus communication and the control functions used to minimize external timing requirements.
Where is the SN74LS645H pinout located?
The SN74LS645H pinout is located in the pin-configuration section of the manufacturer datasheet linked from the official product page. Use the pin-description table to assign data inputs, data outputs, direction control, enable control, power, and ground connections for the exact H orderable. The accessible product page identifies the function family, but the individual pin names and package drawing must be confirmed from the exact-package datasheet before PCB routing.
What is the difference between the SN74LS645H and SN74LS645N?
The SN74LS645H and SN74LS645N are both octal bus transceivers in the SN74LS645 family, but their orderable suffix codes identify different package configurations. The distributor listing for SN74LS645N specifies a 20-PDIP package. Before treating one as a direct substitute for the other, confirm the SN74LS645H package, temperature grade, electrical limits, and lead geometry against the manufacturer documentation for both exact part numbers.
What is the best drop-in replacement for the SN74LS645H?
The best drop-in replacement is the exact same manufacturer and function in the requested package with equivalent pin, timing, supply-voltage, and drive specifications. The SN74LS645N is a documented family member with a 20-PDIP package, but it should not be assumed to be a drop-in replacement until the SN74LS645H package and ordering information are confirmed. Use the Request a Quote form on this page and identify the required package before approving a substitution.
Can SN74LS645N replace SN74LS645H?
SN74LS645N can replace SN74LS645H only if the required footprint, pin function, direction logic, enable logic, timing, and operating grade are verified as identical. The available listing identifies SN74LS645N as a 20-PDIP octal, non-inverting, three-state transceiver. Because the exact SN74LS645H package is not stated on the accessible product page, confirm the H suffix details in the manufacturer datasheet before treating the N version as drop-in compatible.
SN74LS645H vs SN74LS645N: which is better for a legacy TTL board?
SN74LS645H is preferable when it matches the original BOM’s package and qualification requirements exactly, while SN74LS645N may suit a board designed around a 20-PDIP footprint. Both devices represent the same octal, non-inverting, three-state transceiver function within the SN74LS645 family. The deciding factors are the exact package drawing, temperature grade, pinout, timing limits, and supply-voltage range rather than the transceiver description alone.
When should I choose the SN74LS645H over another 74LS transceiver?
Choose the SN74LS645H when the system requires eight bidirectional bus channels with non-inverting, three-state behavior and the original board specifies the H package configuration. It is appropriate for legacy asynchronous buses where controlled drive direction and high-impedance isolation are important. Select another 74LS transceiver only when its channel count, inversion, control truth table, timing, package, and electrical ratings satisfy the complete system interface.
Is the SN74LS645H suitable for shared peripheral and memory buses?
The SN74LS645H is suitable for shared peripheral and memory buses that use compatible asynchronous TTL signaling. Its eight channels and three-state outputs allow bus devices to transmit and receive on common lines, provided an arbitration scheme guarantees that only one driver is enabled at a time. Verify propagation delay, setup and hold timing, input/output loading, and voltage margins against the slowest participant in the bus.
Where can I buy SN74LS645H online and check its price?
Use the Request a Quote form on this page to request SN74LS645H availability, current unit pricing, and quantity breaks from XAIPART. The exact package suffix should be included with the request because SN74LS645 orderable variants can use different package codes. Stock status and lead time should be confirmed at quotation time rather than inferred from a generic family listing or an obsolete distributor record.
What is the lead time for SN74LS645H?
The current SN74LS645H lead time depends on package configuration, quantity, and supply status and must be confirmed through the Request a Quote form on this page. The component is an established 74LS-family octal bus transceiver, but that does not guarantee immediate availability for every suffix or quantity. Include the target package code and production schedule so the quotation can reflect the correct supply path.
Is SN74LS645H currently in stock?
Current SN74LS645H stock status should be confirmed through the Request a Quote form on this page. Available listings include the exact H orderable, but a listing alone does not establish present inventory at the requested quantity. Provide your required package, annual usage, and target quantity to obtain a current supply and lead-time response for production planning.
What are the key specifications of SN74LS645H that engineers should know?
The principal SN74LS645H specifications are its eight-channel organization, asynchronous two-way bus operation, non-inverting signal path, and three-state outputs. Texas Instruments identifies the device as an octal bus transceiver, and the historical family description states that its control functions minimize external timing requirements. Supply range, propagation delay, current ratings, temperature range, and package dimensions must be taken from the datasheet for the exact H orderable.
What can replace SN74LS645H in a legacy TTL system?
A legacy TTL replacement must match the SN74LS645H’s eight non-inverting bidirectional channels, three-state output behavior, control truth table, timing, supply range, package footprint, and operating-temperature requirements. SN74LS645N is a related family member documented with a 20-PDIP package, but package equivalence must be confirmed before use. For an exact-match proposal, submit the complete requirements through the Request a Quote form on this page.
Is SN74LS645H the same as an onsemi-marked SN74LS645H?
An onsemi-marked SN74LS645H has the same visible ordering code and function name, but procurement should verify manufacturer-of-record status, package construction, traceability, and production history before treating the listings as interchangeable. The Texas Instruments product page is the primary family reference used for this configuration. Compare lot traceability and exact package requirements when an onsemi-marked source is proposed for an existing or regulated assembly.

بيانات مرجعية هندسية لـ SN74LS645H — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the SN74LS645H when maintaining an established eight-bit TTL-compatible bus and the original bill of materials specifies the H suffix. Its eight non-inverting, three-state channels support bidirectional transfers and shared-bus isolation, making it appropriate for processor, peripheral, memory, and legacy test-equipment interfaces. Choose SN74LS645N only after confirming that the 20-PDIP package, pinout, temperature grade, timing, and electrical ratings are acceptable for the board. Do not substitute a 74LS family device merely because it also offers three-state outputs; inversion, channel count, direction-control logic, propagation delay, and supply requirements must all match. For new high-speed or low-power systems, a newer logic family may be electrically preferable, but it may require different voltage levels, timing assumptions, and board changes.

المقارنة مع البدائل

المعامل هذا المنتج SN74LS645N
Manufacturer Texas Instruments Texas Instruments
Device Function Octal bus transceiver Octal bus transceiver
Number of Channels 8 channels 8 channels
Signal Polarity Non-inverting Non-inverting
Output Configuration Three-state output Three-state output
Communication Mode Asynchronous two-way communication Asynchronous two-way communication

أبرز الفروقات

  • Matched eight-channel bidirectional interface (مقابلSN74LS645N)
  • Three-state output supports shared-bus isolation (مقابلSN74LS645N)
  • Exact H configuration for original BOM continuity (مقابلSN74LS645N)

ملاحظات التصميم

Do not assume that every SN74LS645 orderable suffix is mechanically interchangeable. The available SN74LS645N listing identifies a 20-PDIP package, while the exact SN74LS645H package must be confirmed from the manufacturer documentation. Compare package drawing, row spacing, lead length, pin numbering, and temperature grade before substitution. A matching function name alone does not establish drop-in compatibility on an assembled legacy board.

Define the bus-enable protocol so that no two transmitters assert the same line during a transition. Use the manufacturer truth table to establish direction and output-enable priority, and include a deliberate dead time if control inputs can change asynchronously. Confirm propagation delay, setup and hold timing, input thresholds, and output-current limits against the slowest connected device and the total bus loading.

Place the transceiver close to the connector or bus-isolation boundary when long external cables are present. Keep the ground return continuous and use the package’s recommended supply and decoupling arrangement to prevent bus transients from coupling into adjacent logic. For through-hole legacy designs, inspect all pins for oxidation and verify that replacement leads do not create shorts between adjacent pads before applying power.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The accessible product information identifies the device and function but does not provide an explicit compliance declaration for the exact SN74LS645H orderable.

تم التحقق من البيانات في: 2026-11-18 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

SN74LS645H datasheet SN74LS645H datasheet pdf SN74LS645H pinout SN74LS645H equivalent SN74LS645H replacement SN74LS645H cross reference SN74LS645H vs SN74LS645N SN74LS645H price SN74LS645H stock Texas Instruments SN74LS645H SN74LS645H octal bus transceiver SN74LS645H application circuit

المكونات والمصطلحات ذات الصلة

Texas Instruments SN74LS645H SN74LS645N SN74LS645 Octal bus transceiver Bidirectional transceiver Bus interface IC Logic IC Digital integrated circuit Semiconductor 74LS logic family SN74LS TTL series Asynchronous two-way communication Three-state output High-impedance state Non-inverting logic Low-power Schottky TTL TTL Eight-bit bus Direction control Output enable Shared peripheral bus Memory interface Industrial control Legacy test equipment
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر