SN74LS682N - 8-Bit Magnitude Comparator | Texas Instruments
MPN: SN74LS682N ✓ نشطSN74LS682N نظرة عامة
An identity or magnitude comparator is a combinational logic device that accepts two multi-bit operands and produces outputs describing their relative relationship. The SN74LS682 belongs to the broader 74LS comparator family, where an 8-bit magnitude comparator compares parallel data rather than determining the order of two individual bits. Its identity function provides a direct equality result, while its magnitude function provides a greater-than result. These operations are useful in control, sorting, address matching, arithmetic sequencing, and test systems.
The principal feature of the SN74LS682N is its dedicated 8-bit comparison architecture. Each operand is presented on a parallel bus, and the internal logic evaluates the complete word rather than requiring a serial sequence of bit-by-bit comparisons. The device provides active-low A=B and A>B outputs, enabling wired-output systems to combine several comparator results. Its 74LS Schottky TTL construction is suited to conventional five-volt logic environments, while the through-hole PDIP package simplifies assembly, inspection, and replacement in legacy or industrial control equipment.
The SN74LS682N differs from related devices in the same 74LS family primarily by its output set. The LS682 supplies equality and greater-than functions; not every related magnitude comparator offers the same combination. This distinction is important because a substitute with the same package and pin count is not automatically interchangeable if its output behavior differs. Engineers should compare truth tables, propagation timing, output polarity, supply requirements, and input-current characteristics before approving any replacement.
Typical uses include equality detection in digital control systems, BCD value comparisons in industrial controllers, parallel sorting and routing logic, address and identification-word recognition, and legacy test equipment. The comparator can also serve as the central decision element in alarm and sequencing circuits where two eight-bit values must be tested continuously. Its parallel interface makes it suitable when the system already presents complete words and requires a hardware-generated status indication without microcontroller comparison code.
PCB design should preserve clear separation between the two operand buses and route each input directly to its corresponding package pin. Decoupling requirements, grounded-return practices, unused-input handling, and TTL input-current budgeting must follow the manufacturer datasheet. Because outputs are active low and totem-pole structured, downstream circuits should account for both voltage levels and fan-out rather than treating the outputs as ideal push-pull signals. Socketed prototypes should also account for contact resistance and contamination at older through-hole connections.
This product page combines the manufacturer function description, package information, family distinctions, pin-verification guidance, and application-oriented replacement criteria to support engineering selection. It also identifies the limits of package-only compatibility: a true drop-in replacement must reproduce the SN74LS682N output truth table and electrical timing in addition to matching the 20-pin PDIP footprint.
بدائل مباشرة لـ SN74LS682N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
SN74LS682N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←SN74LS682N/MOTOROLA
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DM74LS682N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
74HC682N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
74HCT682N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS682N الحدود القصوى والخصائص الكهربائية
| Comparator Type | 8-bit identity/magnitude comparator |
| Number of Input Words | 2 words |
| Input Word Width | 8 bits per word |
| Supported Number Formats | Binary or BCD |
| Identity Output | Active-low A=B output |
| Magnitude Output | Active-low A>B output |
| Output Structure | Totem-pole |
| Logic Family | 74LS Schottky TTL |
| العلبة | 20-pin PDIP |
| عدد الأطراف | 20 pins |
| نوع التركيب | Through-hole |
دليل تكوين أطراف SN74LS682N 20-pin pdip
تكوين الأطراف لـ SN74LS682N (حزمة 20-pin pdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS682N.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74LS682N مناسب لـ 6 التطبيقs: Industrial Control Equality Decision, BCD Value Monitoring, Address and Identifier Recognition, Sorting and Routing Logic, Legacy Test and Measurement Equipment, Alarm Threshold and Sequencing.
Industrial Control Equality Decision
The SN74LS682N fits legacy industrial-control boards that must determine whether two eight-bit process or position values are equal. Its parallel A and B buses allow the comparison result to be generated directly in hardware without occupying a microcontroller input cycle. The active-low A=B output can drive interlock or sequencing logic, while the active-low A>B output supports threshold decisions. Because the device uses a 20-pin PDIP and 74LS TTL signaling, designers should preserve the original bus routing and verify voltage levels, fan-out, propagation delay, and supply conditions before using it in an updated controller.
موصى به
BCD Value Monitoring
The SN74LS682N can monitor two eight-bit BCD words in legacy meters, counters, and sequencing equipment. It accepts complete BCD operand buses and produces active-low equality and greater-than outputs, making it useful for indicating when a measured value reaches, exceeds, or matches a preset value. The comparison is performed in parallel rather than through a serial bit-by-bit routine. In a redesigned board, the engineer should verify the exact output truth table, input levels, timing, and supply requirements from the manufacturer datasheet, especially if peripheral devices use mixed TTL and CMOS interfaces.
موصى به
Address and Identifier Recognition
The SN74LS682N is useful in address-matching and identification-word circuits because it can compare two complete eight-bit identifiers in parallel. Its active-low A=B output can indicate that a received code matches a stored reference, while A>B provides an ordering result for subsequent logic. This makes the device suitable for legacy access-control, routing, and equipment-recognition assemblies that already use 74LS-level signals. Board reuse is practical because the SN74LS682N is a 20-pin PDIP, but functional validation must include output polarity, fan-out, propagation delay, and the behavior of every connected TTL input.
موصى به
Sorting and Routing Logic
The SN74LS682N can serve as a hardware sorting element when two eight-bit values must be ordered quickly. The greater-than result helps downstream combinational logic select a path, route a value, or advance a sequence, while the equality result identifies a match. Parallel evaluation reduces the need to perform a software comparison and is valuable in older automation equipment. The implementation should account for the difference between active-low outputs and familiar positive-logic control signals, and it should use the manufacturer timing data when cascading comparator decisions or combining outputs from multiple devices.
موصى به
Legacy Test and Measurement Equipment
The SN74LS682N fits legacy test equipment that compares an eight-bit DUT response with a reference word and reports equality or magnitude through hardware. Such arrangements are common in production fixtures, interface testers, and diagnostic panels built with 74LS logic. The device's 20-pin PDIP package is straightforward to socket, inspect, and replace during maintenance. Before substituting it into a newer fixture, verify supply voltage, TTL input thresholds, output polarity, fan-out, and propagation delay. A same-package comparator with a different output complement may produce incorrect pass or fail decisions even if it powers up normally.
موصى به
Alarm Threshold and Sequencing
The SN74LS682N can provide a hardware threshold decision in alarm, interlock, and multi-stage sequencing systems. When an eight-bit measured value becomes greater than a reference word, the active-low A>B output can participate in the next control stage; when the two words match, the active-low A=B output can trigger a separate event path. Because the outputs are active low, inverter stages may be required to create conventional positive-logic enables. The design should preserve adequate fan-out, provide clean ground returns, and verify timing against the rest of the 74LS control chain before production use.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS682N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SN74LS682N | SN74LS682N/MOTOROLA | DM74LS682N | 74HC682N | 74HCT682N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | ON Semiconductor | Motorola | onsemi | NXP Semiconductors | NXP Semiconductors |
| Package | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 |
| Comparator Resolution | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Logic Technology | 74LS Schottky TTL | 74LS Schottky TTL | 74LS Schottky TTL | 74LS Schottky TTL | CMOS | CMOS with TTL-compatible inputs |
أبرز الفروقات
- Provides both equality and greater-than decisions in one 8-bit comparator (مقابلSN74LS684)
- Uses the 74LS Schottky TTL interface expected by legacy five-volt control boards (مقابل74HC682N)
- Supports direct TTL interfacing while retaining the familiar 20-pin PDIP footprint (مقابل74HCT682N)
ملاحظات التصميم
Do not treat every 74LS comparator with a 20-pin PDIP package as an interchangeable SN74LS682N. The SN74LS682 specifically provides active-low A=B and A>B outputs, while related LS684, LS685, LS687, and LS688 devices have different output combinations. Create a substitution matrix covering every output, input position, power pin, polarity, and timing condition. A package match that fails the truth-table review can create unsafe or misleading control decisions.
Budget the TTL input current from every bus driver and connected device rather than assuming that all logic inputs present negligible loading. The SN74LS682N uses Schottky TTL levels, and mixed 74LS, 74HCT, or CMOS peripherals can introduce threshold and fan-out problems. Check the manufacturer input-current table, maintain compatible supply arrangements, and use pull-up or pull-down networks where the specified logic levels require them.
Assign the A bus and B bus to separate, consistently routed groups and keep the comparator close enough to avoid unnecessary propagation delay across the board. Maintain a continuous ground reference, avoid stubs on sensitive legacy interconnects, and provide local supply bypassing according to the manufacturer datasheet. For through-hole assembly, inspect sockets and connector contacts for corrosion or increased resistance because marginal connections can create intermittent comparison errors.
Verify that the board supply remains within the SN74LS682N operating range during startup and fault conditions. A stable logic voltage is essential because invalid threshold transitions can cause the equality or greater-than outputs to switch unpredictably. Use the manufacturer power and absolute-maximum ratings when planning new supplies, and preserve adequate current margin for the comparator and every device sharing the same rail.
معلومات الامتثال
The exact material-compliance declarations for SN74LS682N are not stated in the available manufacturer-page excerpts. Automotive qualification is not indicated for this device.