STM32F401CBU3 - 84MHz 128KB Cortex-M4 MCU | STMicroelectronics
MPN: STM32F401CBU3 ✓ نشطSTM32F401CBU3 نظرة عامة
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The STM32F401CBU3 sits within the hierarchy of microcontrollers, embedded processors, and programmable control devices. Its Cortex-M4 processor uses the Thumb instruction set and provides deterministic real-time control capabilities for products that need more processing capacity than a basic logic controller but require a compact, low-power implementation.
The principal device attributes include a maximum CPU frequency of 84 MHz, 128 KB of embedded Flash, a 1.7 V to 3.6 V operating supply range, and a choice of -40 °C to 85 °C or -40 °C to 105 °C temperature grades within the device family. The UFQFPN package measures 7 mm by 7 mm and provides a practical land pattern for compact industrial controllers, sensor nodes, medical instruments, and connected equipment. An exposed pad supports thermal dissipation where the PCB layout permits.
The Cortex-M4 core is designed for efficient embedded workloads and includes DSP and floating-point capabilities. These features allow real-time signal processing, control calculations, and protocol handling to execute directly on the MCU. The STM32F4 product family emphasizes the balance between processing performance and dynamic power consumption, making the STM32F401CBU3 suitable for systems that need deterministic behavior without the resource demands of a higher-end application processor.
Typical applications include industrial sensor aggregation, compact motor and process controllers, medical monitoring equipment, building automation modules, and portable diagnostic instruments. Communication interfaces can connect the MCU to transceivers, sensors, display controllers, and isolated interface circuits, while the 84 MHz processing rate supports responsive control loops and moderate protocol traffic.
PCB design should preserve the manufacturer’s recommended decoupling, exposed-pad, and thermal-via layout. Place power and ground connections carefully, route sensitive inputs away from high-current paths, and validate the final board across the intended voltage and temperature range. Firmware and peripheral configuration should also be checked against the exact package variant before production release.
This product page combines the STM32F401CBU3 specifications, package guidance, application context, and same-package replacement options in a form intended for straightforward engineering evaluation and sourcing decisions.
بدائل مباشرة لـ STM32F401CBU3 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع STM32F401CBU3 (نفس عامل الشكل والبصمة) — يختلف في Package, Flash Memory, Flash Organization, Product Type, Core.
STM32F401CBU6
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←STM32F401CCU3
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F401CCU6
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←STM32F401CCU6TR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F401CEU3
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
STM32F401CEU6
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←STM32F401CBU3 الحدود القصوى والخصائص الكهربائية
| Product Type | 32-bit ARM Cortex-M4 microcontroller |
| CPU Core | Arm Cortex-M4 with DSP and FPU |
| Maximum CPU Frequency | 84 MHz |
| Instruction Set | 32-bit ARM Thumb |
| Flash Memory | 128 KB |
| Flash Organization | 128K x 8 bits |
| جهد التغذية التشغيلي | 1.7 V to 3.6 V |
| Nominal Supply Options | 1.8 V, 2.5 V, or 3.3 V |
| Temperature Range | -40 °C to 85 °C or -40 °C to 105 °C |
| العلبة | 48-pin UFQFPN, 7 mm x 7 mm |
| Package Type | Surface-mount UFQFPN with exposed pad |
| نوع التركيب | Surface Mount |
| Peripheral Class | DSP and floating-point unit |
| Product Family | STM32F4 Dynamic Efficiency Line |
دليل تكوين أطراف STM32F401CBU3 surface-mount ufqfpn with exposed pad
تكوين الأطراف لـ STM32F401CBU3 (حزمة surface-mount ufqfpn with exposed pad). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ STM32F401CBU3.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
STM32F401CBU3 مناسب لـ 6 التطبيقs: Industrial Sensor Hub, Medical Monitoring Instrument, Compact Process Controller, Portable Diagnostic Device, Building Automation Module, Connected Control Node.
Industrial Sensor Hub
The STM32F401CBU3 fits an industrial sensor hub that combines periodic acquisition, local filtering, and deterministic control in a compact 48-pin package. Its 84 MHz Cortex-M4 core executes DSP and floating-point instructions without requiring a separate processor, while the 128 KB embedded Flash stores application firmware and configuration logic. The 1.7 V to 3.6 V operating range supports 1.8 V, 2.5 V, and 3.3 V system rails. A sensor interface can feed measurements into the MCU for threshold evaluation, logging, and communication, while the 7 mm by 7 mm UFQFPN outline preserves board area in DIN-rail or embedded equipment. The principal design consideration is thermal exposure: select the 85 °C grade only when the enclosure remains within its rated ambient range, or use the 105 °C CBU6 alternative for hotter installations.
موصى به
Medical Monitoring Instrument
The STM32F401CBU3 is appropriate for compact medical monitoring equipment that performs sensor conditioning in real time and maintains control over an instrument bus or display interface. Its 84 MHz Cortex-M4 processor includes DSP and floating-point support, allowing filtering and scaling calculations to run locally without slowing the main control loop. The 128 KB Flash footprint is suitable for application firmware, calibration tables, and communication protocols when no large stored data set is required. Operating from 1.7 V to 3.6 V also permits use of low-voltage sensor and communication circuits. Medical-product designers must add the required isolation, protection, creepage, and regulatory controls at the system level. The MCU should remain within its specified 85 °C maximum for the CBU3 suffix, making the CBU6 grade preferable where elevated internal temperatures are expected.
موصى به
Compact Process Controller
The STM32F401CBU3 suits compact process controllers that must execute control calculations, monitor inputs, and coordinate outputs within a small embedded enclosure. At 84 MHz, the Cortex-M4 core provides deterministic responsiveness for proportional, integral, derivative, and filtering routines, while its DSP and FPU capabilities reduce the computational overhead of signal-oriented control functions. The 128 KB of embedded Flash accommodates a typical embedded control application without external program storage. With its 48-pin UFQFPN footprint, the device supports compact layouts, and the exposed pad can improve thermal performance when connected to copper through the manufacturer-recommended via pattern. Supply design should use a regulated rail within 1.7 V to 3.6 V, with local decoupling placed at the power pins. If enclosure temperatures can exceed 85 °C, the CBU6 replacement offers the same footprint with a 105 °C grade.
موصى به
Portable Diagnostic Device
The STM32F401CBU3 supports portable diagnostic devices where low-voltage operation, compact dimensions, and real-time signal processing are important. The Cortex-M4 processor can execute DSP instructions and floating-point calculations for sensor compensation, waveform analysis, and measurement control at up to 84 MHz. Its 128 KB Flash capacity is suitable for firmware, calibration coefficients, and fixed protocol data, while the 1.7 V minimum supply voltage accommodates compact battery-derived rails after suitable regulation. The 7 mm by 7 mm package limits occupied board area and can suit handheld or wearable-style instrument enclosures. Developers should calculate the regulator’s efficiency and thermal behavior across the complete battery range, while keeping sensitive analog routing separate from digital and switching paths. The standard CBU3 grade is appropriate for controlled handheld temperatures; a 105 °C-rated family member is safer for devices exposed to elevated internal temperatures.
موصى به
Building Automation Module
The STM32F401CBU3 can serve as the local controller in a building automation module that supervises environmental inputs, drives outputs, and reports status over a serial or network interface. Its 84 MHz Cortex-M4 core provides more than enough throughput for protocol management, scheduling logic, diagnostics, and real-time control, while the 128 KB embedded Flash supports a compact application without a companion program-memory device. The compact UFQFPN-48 package is well suited to wall modules and DIN-rail products where every millimeter matters. A low-voltage 1.8 V, 2.5 V, or 3.3 V rail can simplify integration with sensors and transceiver circuitry, provided the power design maintains the MCU’s operating limits. Because building equipment may operate in warm enclosures, system thermal qualification should confirm whether the 85 °C CBU3 grade is adequate or whether the 105 °C CBU6 option should be selected.
موصى به
Connected Control Node
The STM32F401CBU3 is a strong core for a connected control node that gathers local data, performs calculations, and forwards commands between sensors and a supervisory system. Its 84 MHz Cortex-M4 core with DSP and FPU support handles protocol overhead, filtering, and control tasks concurrently, while the 128 KB Flash footprint is appropriate for compact firmware without external storage. The 48-pin UFQFPN package offers a practical balance between pin access and board area, and its exposed pad supports heat spreading when the PCB provides adequate copper. Communications isolation, termination, and surge protection must be implemented according to the external interface requirements rather than assumed to be part of the MCU. Power architecture should account for the difference between the 1.7 V minimum operating voltage and the voltage required by attached interfaces. For deployed equipment with high internal ambient temperature, use a 105 °C-rated same-package option.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ STM32F401CBU3 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | STM32F401CBU6 | STM32F401CCU3 | STM32F401CCU6 | STM32F401CCU6TR | STM32F401CEU3 |
|---|---|---|---|---|---|---|
| Package | UFQFPN-48 (7x7 mm) | UFQFPN-48 (7x7 mm) | UFQFPN-48 (7x7 mm) | UFQFPN-48 (7x7 mm) | UFQFPN-48 (7x7 mm) | UFQFPN-48 (7x7 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | Arm Cortex-M4 with DSP and FPU | Arm Cortex-M4 with DSP and FPU | Arm Cortex-M4 with DSP and FPU | Arm Cortex-M4 with DSP and FPU | Arm Cortex-M4 with DSP and FPU | Arm Cortex-M4 with DSP and FPU |
| Maximum CPU Frequency | 84 MHz | 84 MHz | 84 MHz | 84 MHz | 84 MHz | 84 MHz |
| Flash Memory | 128 KB | 128 KB | 256 KB | 256 KB | 256 KB | 512 KB |
| Operating Supply Voltage | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V |
| Upper Operating Temperature | 85 °C | 105 °C | 85 °C | 105 °C | 105 °C | 85 °C |
| Programming and Debug | STM32F4 Cortex-M4 programming and debug interface | STM32F4 Cortex-M4 programming and debug interface | STM32F4 Cortex-M4 programming and debug interface | STM32F4 Cortex-M4 programming and debug interface | STM32F4 Cortex-M4 programming and debug interface | STM32F4 Cortex-M4 programming and debug interface |
| Special Feature | Dynamic Efficiency MCU with 128 KB Flash | 105 °C temperature grade | 256 KB Flash | 256 KB Flash and 105 °C temperature grade | 256 KB Flash, 105 °C temperature grade, tape-and-reel format | 512 KB Flash |
أبرز الفروقات
- Maintains the same 128 KB memory configuration while extending temperature capability (مقابلSTM32F401CBU6)
- Provides twice the embedded Flash without changing the package footprint (مقابلSTM32F401CCU3)
- Combines additional Flash with wider temperature operation (مقابلSTM32F401CCU6TR)
- Offers the largest same-package firmware headroom for growing applications (مقابلSTM32F401CEU3)
ملاحظات التصميم
Implement the manufacturer’s UFQFPN-48 land pattern and exposed-pad connection exactly. Place the input and output decoupling capacitors close to their associated power pins, keep the exposed-pad region free of unintended shorts, and use a thermal-via pattern sized for the board copper and enclosure heat flow. Avoid placing sensitive analog traces beneath noisy digital or power-conversion paths.
Design the supply rail to remain between 1.7 V and 3.6 V across temperature, load, and startup. Confirm the voltage at the MCU pins rather than relying only on the regulator output. Stable local bypass capacitance, controlled power-up timing, and correct brownout behavior are essential for reliable Cortex-M4 operation and repeatable peripheral initialization.
Validate the assembled device at the maximum intended ambient temperature and worst-case processing activity. The CBU3 order code is associated with an 85 °C upper operating limit, so internal enclosure heating can leave insufficient margin even when the external ambient appears acceptable. Choose a 105 °C-rated same-package variant if thermal analysis shows operation above 85 °C.
Do not treat the B, C, and E memory variants as interchangeable without reviewing firmware size and startup assumptions, and do not confuse the 3 and 6 temperature-grade suffixes. When changing to a larger Flash device, confirm linker placement, option-byte behavior, boot configuration, and production programming procedures. A same-package replacement still requires board-level and firmware validation.
Route clocks and communication signals away from switching nodes and high-current output paths. Use a continuous ground reference beneath and around the device, minimize loop area for clock and return paths, and observe the manufacturer’s external-component recommendations for oscillator and bus speeds. Validate timing with the production peripheral configuration rather than relying on generic STM32 examples.
معلومات الامتثال
The manufacturer product page identifies STM32F401CB as an active device. Specific environmental and material compliance declarations for the exact STM32F401CBU3 order code should be confirmed in the current manufacturer documentation or declaration records.