TAS5805MPWP - 23W Stereo Class-D Audio Amplifier | Texas Instruments
MPN: TAS5805MPWP ✓ نشطTAS5805MPWP نظرة عامة
A Class-D audio amplifier is a switching power amplifier that uses a high-frequency PWM output stage to deliver audio energy to a speaker. It belongs to the hierarchy of audio amplifiers, linear audio amplifiers, and power-management semiconductors. Compared with a conventional linear output stage, the TAS5805M architecture is intended to reduce power loss and provide a cost-effective digital-input solution while retaining closed-loop speaker-current feedback.
The TAS5805M integrates a 96 kHz signal-processing architecture with sample-rate conversion, 15 biquads per channel, volume control, audio mixing, three-band fourth-order dynamic range control, full-band automatic gain limiting, and THD management. This combination supports speaker protection, level control, and source-specific tuning without requiring a separate digital-audio processor for every basic function.
The device supports stereo or mono operation and can deliver up to 23 W per stereo channel under the conditions specified by Texas Instruments. Its 4.5 V to 26.4 V supply range accommodates portable, industrial, and consumer audio systems. The manufacturer describes the design as inductor-less, allowing the external speaker interface to use a conventional LC filter rather than requiring an output inductor.
Typical uses include soundbars, smart speakers, television and monitor audio, compact consumer systems, and other digital-input audio products. The 96 kHz processing architecture is particularly relevant when the design needs advanced level management and speaker protection close to the power stage. Digital control data is handled through the device's serial audio and control interface.
A critical layout requirement is keeping the Class-D switching node compact and isolated from sensitive input and control traces. Follow the manufacturer datasheet's power, ground, decoupling, and filter-layout guidance because high dV/dt switching edges can create EMI coupling and ground bounce. The exposed thermal pad also requires careful thermal design when the amplifier operates near its maximum output power.
This product page combines the exact ordering information, verified manufacturer and distributor resources, strict drop-in assessment, application guidance, and design-focused comparisons. It helps engineers determine whether the TAS5805MPWP fits a digital-input speaker design before committing to a PCB or firmware configuration.
بدائل مباشرة لـ TAS5805MPWP — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلTAS5805MPWP الحدود القصوى والخصائص الكهربائية
| Device Type | Digital-input, closed-loop Class-D stereo audio amplifier |
| تكوين الخرج | 2-channel stereo or 1-channel mono |
| Maximum Stereo Output Power | 23 W |
| Maximum Mono Output Power | 45 W |
| Supply Voltage Range | 4.5 V to 26.4 V |
| Architecture | Closed-loop Class-D |
| Output Filter Requirement | Inductor-less |
| Input Format | Digital input |
| Processor Architecture | 96 kHz |
| Biquads per Channel | 15 |
| Dynamic Range Control | 3-band, 4th-order |
| Automatic Gain Limiting | Full-band |
| THD Management | Integrated |
| Sample-Rate Conversion | Supported |
| Audio Mixing | Supported |
| Volume Control | Supported |
| العلبة | 28-pin HTSSOP |
| نوع التركيب | Surface mount |
دليل تكوين أطراف TAS5805MPWP 28-pin htssop
تكوين الأطراف لـ TAS5805MPWP (حزمة 28-pin htssop). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ TAS5805MPWP.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
TAS5805MPWP مناسب لـ 6 التطبيقs: Compact Stereo Speaker, Soundbar Speaker Module, Television Audio Platform, Smart Speaker, Digital-Input Audio Module, Industrial Audio Annunciator.
Compact Stereo Speaker
The TAS5805MPWP fits a compact powered speaker that accepts digital audio and needs up to 23 W per stereo channel. Its digital-input architecture avoids an analog-input stage near the power amplifier, while the integrated 96 kHz processor provides volume control, sample-rate conversion, mixing, and 15 biquads per channel. This can simplify signal routing in a soundbar, compact stereo, or multimedia speaker. The designer must still select the correct speaker filter, verify operation at the intended 4.5 V to 26.4 V supply, and validate that the chosen audio level remains thermally practical. Filter and feedback layout should follow the manufacturer recommendations because the high-voltage switching node can couple interference into nearby control paths.
موصى به
Soundbar Speaker Module
The TAS5805MPWP is well suited to a soundbar channel because its digital input supports direct integration with a system audio bus, and its integrated DRC, AGL, and THD management can protect a compact speaker from program-level variations. The 23 W stereo capability provides useful output headroom without requiring a separate analog codec. In this application, channel routing and volume behavior should be configured through the control interface, while the external speaker filter must be tuned for the actual impedance. PCB placement should isolate the Class-D switching node from the digital input and control traces to limit EMI in a consumer enclosure that may also contain radio, display, and switching-power circuitry.
موصى به
Television Audio Platform
The TAS5805MPWP can provide efficient stereo speaker drive in a television or monitor platform when the host processor supplies digital audio. Its integrated mixer and sound-processing resources can support multiple source paths, level control, and speaker protection, reducing the need for separate digital signal-processing hardware. The 4.5 V minimum supply supports integration with common low-voltage audio rails, but engineers must verify the amplifier's output-power curve at the actual rail and load. Thermal copper must extend beneath the package's exposed thermal area, and the switching output should be routed away from sensitive display, tuner, and microphone circuitry to preserve signal integrity within the enclosure.
موصى به
Smart Speaker
The TAS5805MPWP supports a smart-speech or connected-audio product that combines digital source routing with local speaker amplification. Digital mixing, SRC, volume control, and programmable biquads can consolidate signal management near the power stage, while DRC, AGL, and THD management add useful protection functions. For a voice-enabled product, the amplifier layout must remain separated from microphone analog paths and other low-level sensing circuits. The 23 W stereo rating can suit compact speakers, but thermal performance depends on supply voltage, channel loading, efficiency, and ambient conditions. Firmware configuration should be coordinated with the control-interface timing and audio-clock requirements described by Texas Instruments.
موصى به
Digital-Input Audio Module
The TAS5805MPWP is suitable for a modular digital audio output card that accepts compressed or PCM audio from a host processor and drives passive speakers directly. Its integrated 96 kHz processing architecture allows equalization, level control, DRC, AGL, and THD management to be consolidated within the power-amplifier module. Using the module approach also keeps analog audio traces away from the digital source and reduces board area in space-constrained systems. The engineer must define the digital clocking and control protocol correctly, implement the recommended external filter, and maintain a continuous ground reference beneath and around the power stage. Validate startup, mute behavior, speaker impedance, and thermal rise before releasing the module for volume production.
موصى به
Industrial Audio Annunciator
The TAS5805MPWP can drive a high-efficiency stereo or bridged mono speaker used in an industrial annunciator, control cabinet, or operator-console audio system. Digital input allows announcements to originate from a central controller, while integrated mixing and volume functions help manage multiple message paths. The 23 W stereo and 45 W mono headline capabilities offer useful flexibility, subject to the actual supply and load conditions. Industrial equipment should account for enclosure temperature, long operating duty cycles, and isolation from electromagnetic fields. Use filtering that matches the chosen speaker impedance, maintain low-impedance decoupling, and route switching-node copper carefully so announcements remain intelligible without audible filter or switching interference.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TAS5805MPWP — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Manufacturer | Texas Instruments |
| Package | 28-pin HTSSOP |
| Output Configuration | Stereo or mono |
| Maximum Stereo Output Power | 23 W |
| Maximum Mono Output Power | 45 W |
| Supply Voltage Range | 4.5 V to 26.4 V |
| Amplifier Architecture | Digital-input, closed-loop Class-D |
| Processing Architecture | 96 kHz with 15 biquads per channel |
| Speaker Protection Features | 3-band DRC, full-band AGL, and THD management |
| Output Filter | Inductor-less architecture with external filter |
ملاحظات التصميم
Keep the Class-D switching node and external filter loop as small as practical, and route them away from the digital-audio input, control signals, and feedback traces. Provide a continuous ground plane beneath the power stage and place local input, output, and bypass connections directly at their associated pins. Follow the Texas Instruments datasheet layout pattern exactly because a large switching loop can increase EMI, ground bounce, and susceptibility to audible interference.
Estimate dissipation from the actual supply voltage, output power, channel loading, and amplifier efficiency, then verify junction temperature with the PCB's thermal copper area and the worst-case ambient temperature. The 23 W stereo and 45 W mono figures are maximum capability figures rather than guarantees across every voltage and load condition. Avoid reducing thermal-pad solder coverage; use the manufacturer's recommended land pattern and verify the assembled board rather than relying only on an estimated temperature rise.
Use low-ESR, appropriately rated bypass capacitors close to the supply pins and route the power return through the package thermal area as specified by the manufacturer. Place the external speaker-filter components where their switching current produces the smallest loop. Confirm supply tolerance, startup sequencing, mute behavior, and maximum input conditions so the amplifier never operates outside the 4.5 V to 26.4 V supply range.
Do not interpret the 23 W stereo rating as guaranteed output at every supply voltage or speaker impedance. Review the output-power tables, external-filter requirements, feedback configuration, and supported channel modes in the TAS5805M datasheet. Also avoid treating functionally similar TAS5806M, TAS5807M, or TAS5808M products as drop-in replacements without verifying package dimensions, exposed-pad geometry, pin numbering, and control-interface compatibility.
معلومات الامتثال
The verified Texas Instruments product and distributor information does not explicitly state the requested compliance attributes. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status in the current manufacturer product documentation before procurement.