TLE8250GVIOXUMA1 - 1 Mbaud CAN Transceiver | Infineon
MPN: TLE8250GVIOXUMA1 ✓ نشطTLE8250GVIOXUMA1 نظرة عامة
A CAN transceiver is an interface IC that connects a host controller’s logic-level TXD and RXD signals to a differential CAN bus. It belongs to the interface IC hierarchy, where a controller handles protocol and message processing while the transceiver converts digital commands into bus-level signals and converts received bus activity back into logic. The TLE8250GVIOXUMA1 provides this physical-layer function in a surface-mount package suitable for automotive, industrial, and embedded control systems.
Key electrical features include operation from 4.5 V to 5.5 V, a maximum supported data rate of 1 Mbaud, and 200 mV receiver hysteresis. The hysteresis helps the receiver distinguish signaling states in the presence of bus noise. Infineon also identifies the TLE8250GVIO family as a high-speed, ISO 11898-2-compliant CAN transceiver with low electromagnetic emissions and high electromagnetic immunity.
The device is positioned as a successor-generation HS CAN transceiver and is described as pin and function compatible with the preceding TLE6250GV33. Its half-duplex architecture allows a node to transmit and receive on the same CAN bus through CANH and CANL. Logic-side control and reporting are separated from the differential bus interface, allowing an MCU, automotive communications controller, or industrial CAN controller to connect without adding discrete bus-driver circuitry.
Typical applications include automotive body and powertrain electronics, industrial automation controllers, electric-vehicle subsystems, building automation gateways, CAN-connected sensors, and embedded motor-control systems. A CAN node using the TLE8250GVIOXUMA1 can operate at rates up to 1 Mbaud while benefiting from the family’s low EMI emissions and high EMI robustness.
When designing the PCB around this transceiver, place the device near the CAN connector or bus header to minimize exposed high-frequency bus traces. Keep CANH and CANL routing symmetrical, provide the bus-side network recommended by the manufacturer, and maintain a clean ground return. Verify transceiver logic levels, supply tolerance, pin compatibility, and bus termination independently before replacing another CAN interface device.
This product page combines the manufacturer’s family-level specifications with practical application guidance, package information, sourcing questions, and a pin-compatible replacement analysis. These engineering-oriented details help designers evaluate the TLE8250GVIOXUMA1 for new CAN nodes, legacy replacements, and production-risk assessment without relying only on a catalog summary.
بدائل مباشرة لـ TLE8250GVIOXUMA1 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع TLE8250GVIOXUMA1 (نفس عامل الشكل والبصمة) — يختلف في Package, RoHS Status, Supply Voltage Range.
TLE6250GV33XUMA1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←TLE8250GVIOXUMA5
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←TJA1051T,118
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN75451BD
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN75453BD
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TLE8250GVIOXUMA1 المواصفات
| Product Type | CAN bus transceiver |
| Transceiver Configuration | 1 transmitter / 1 receiver |
| Duplex Mode | Half-duplex |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 1 Mbaud |
| Receiver Hysteresis | 200 mV |
| CAN Standard | ISO 11898-2 |
| العلبة | PG-DSO-8-16 |
| Terminal Count | 8 |
| نوع التركيب | Surface mount |
| Package Height | 1.75 mm maximum |
| Lead Form | Gull wing |
| Package Shape | Rectangular |
| حالة RoHS | Compliant |
| Predecessor Compatibility | Pin and function compatible with TLE6250GV33 |
| Electromagnetic Emissions | Low EME |
| Electromagnetic Immunity | High EMI robustness |
دليل تكوين أطراف TLE8250GVIOXUMA1 rectangular
تكوين الأطراف لـ TLE8250GVIOXUMA1 (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ TLE8250GVIOXUMA1.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
TLE8250GVIOXUMA1 مناسب لـ 6 التطبيقs: Automotive Body Control Modules, Industrial Automation Controllers, Electric Vehicle Subsystems, Building Automation Gateways, CAN-Connected Sensor Hubs, Embedded Motor-Control Systems.
Automotive Body Control Modules
The TLE8250GVIOXUMA1 fits automotive body-control and comfort modules that use a 5 V CAN physical layer. Its 4.5 V to 5.5 V supply range supports regulated 5 V electronics, while operation up to 1 Mbaud allows it to participate in faster CAN segments when topology and cable length permit. The 200 mV receiver hysteresis improves noise tolerance, and the family’s low EME and high EMI robustness are valuable in electrically demanding vehicles. Place the transceiver near the CAN connector, maintain a continuous ground reference, and verify automotive temperature and qualification requirements against the exact ordering code before production release.
موصى به
Industrial Automation Controllers
The TLE8250GVIOXUMA1 is suitable for PLCs, factory controllers, and remote I/O nodes connected through a high-speed CAN bus. Its ISO 11898-2 physical-layer compliance, 1 Mbaud capability, and half-duplex architecture align with common industrial CAN networks. A 200 mV receiver hysteresis helps the node recognize valid differential states in electrically noisy factory environments. The 8-pin PG-DSO-8-16 package also keeps the bus interface compact. Confirm the operating-temperature range, bus-fault exposure, termination strategy, isolation needs, and equipment-level EMC requirements before integrating it into machinery-control electronics.
موصى به
Electric Vehicle Subsystems
The TLE8250GVIOXUMA1 can connect high-speed CAN networks used by electric-vehicle supervisory, body, thermal-management, or charging subsystems. Its 4.5 V to 5.5 V operating range matches common low-voltage digital rails, and the 1 Mbaud capability supports faster communication segments than lower-speed CAN devices. Low electromagnetic emissions help reduce interference within the vehicle, while high EMI robustness supports operation in a challenging electrical environment. Use short, symmetrical CANH and CANL routing, preserve the ground connection, and validate the complete power and fault conditions required by the vehicle platform.
موصى به
Building Automation Gateways
The TLE8250GVIOXUMA1 is appropriate for building-automation gateways, room controllers, and energy-management nodes that connect embedded controllers to a CAN-based sensor network. Its half-duplex 1/1 configuration and 1 Mbaud rate provide adequate bandwidth for control traffic, while the 200 mV receiver hysteresis assists reliable reception in installations with nearby motors and switching equipment. The compact 8-pin surface-mount package simplifies dense controller layouts. Validate temperature performance, bus protection, grounding, shield termination, and the network’s timing budget before deploying it in building controls.
موصى به
CAN-Connected Sensor Hubs
The TLE8250GVIOXUMA1 can serve as the bus interface in a multi-sensor acquisition hub for environmental monitoring, condition monitoring, or industrial sensing. A 1 Mbaud CAN rate permits timely collection of measurements from multiple nodes, and ISO 11898-2 compliance supports standardized physical-layer behavior. The 200 mV receiver hysteresis improves tolerance of local noise from sensors and relays. Because many sensor hubs operate from constrained 5 V rails, the 4.5 V to 5.5 V supply range is also useful. Confirm startup behavior, bus standby requirements, fault recovery, and environmental limits for the installation.
موصى به
Embedded Motor-Control Systems
The TLE8250GVIOXUMA1 is useful in embedded motor-control and actuator nodes that exchange commands and diagnostics over a CAN network. Its 1 Mbaud capability supports responsive communication, while half-duplex operation allows transmission and reception over the same differential bus. The 200 mV receiver hysteresis helps distinguish valid messages when motor drives, relays, and power stages introduce electrical noise. The 8-pin PG-DSO-8-16 package minimizes board area beside a controller and driver circuitry. Verify operating temperature, isolation, bus protection, grounding, and shutdown behavior against the motor-drive system requirements.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TLE8250GVIOXUMA1 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TLE6250GV33 | TLE8250GVIOXUMA5 | TJA1051T,118 | SN75451BD | SN75453BD |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | NXP Semiconductors | Texas Instruments | Texas Instruments |
| Package | PG-DSO-8-16 | PG-DSO-8-16 | PG-DSO-8-16 | PG-DSO-8-16 | PG-DSO-8-16 | PG-DSO-8-16 |
| Product Type | CAN transceiver | CAN transceiver | CAN transceiver | CAN interface transceiver | CAN interface transceiver | CAN interface transceiver |
أبرز الفروقات
- Explicit manufacturer-backed compatibility with the preceding CAN transceiver (مقابلTLE6250GV33)
- Documented receiver hysteresis for noisy CAN networks (مقابلTJA1051T,118)
- Low-emission and high-immunity family positioning (مقابلSN75451BD)
- 4.5 V to 5.5 V operating range (مقابلSN75453BD)
ملاحظات التصميم
Place the TLE8250GVIOXUMA1 close to the CAN connector or bus header and keep the CANH and CANL paths short, matched in geometry, and free of unnecessary stubs. Provide a low-impedance ground-plane connection and avoid routing bus signals beneath switching nodes or high-current return paths. The 8-pin PG-DSO-8-16 package supports compact placement, but its thermal and electrical performance still depends on a sound ground reference and the manufacturer’s recommended external network.
Treat CANH and CANL as a coupled differential pair. Match trace geometry and length where practical, maintain clearance from unrelated high-voltage or switching conductors, and use the termination and common-mode network specified for the complete bus topology. The TLE8250GVIOXUMA1 supports rates up to 1 Mbaud, but stable operation also depends on cable length, propagation delay, controller timing, node count, and termination placement.
Do not assume that a catalog cross-reference proves drop-in equivalence. Compare the exact pin-description table, TXD polarity, RXD output type, standby or enable state, supply range, bus-fault behavior, loop delay, and package drawing. TLE6250GV33 has explicit manufacturer support for pin and function compatibility with TLE8250GVIO, while cross-brand candidates require a full electrical and qualification review before substitution.
Use a continuous ground reference beneath and around the transceiver, decouple the 5 V supply locally, and keep switching-regulator and high-current paths away from CANH and CANL. The TLE8250GVIO family is characterized by low electromagnetic emissions and high electromagnetic immunity, but those characteristics support—not replace—a careful PCB design. Validate the completed product against the applicable system-level EMC requirements and the intended CAN network environment.
معلومات الامتثال
The component listing identifies the PG-DSO-8 package as RoHS compliant. ISO 11898-2 compliance applies to the CAN physical interface. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ordering code.