Infineon

TLE8250GVIOXUMA1 - 1 Mbaud CAN Transceiver | Infineon

부품 번호: TLE8250GVIOXUMA1 ✓ 활성
4.5 V to 5.5 V Vdss PG-DSO-8-16 Package Low EME Memory
MOQ: 1 |

TLE8250GVIOXUMA1 개요

Infineon TLE8250GVIOXUMA1 is a half-duplex high-speed CAN transceiver with one transmitter and one receiver, a 4.5 V to 5.5 V supply range, data rates up to 1 Mbaud, and an 8-pin PG-DSO-8-16 package. It is designed for CAN bus nodes requiring ISO 11898-2-compliant physical-layer communication, robust signal reception, and strong electromagnetic immunity.

A CAN transceiver is an interface IC that connects a host controller’s logic-level TXD and RXD signals to a differential CAN bus. It belongs to the interface IC hierarchy, where a controller handles protocol and message processing while the transceiver converts digital commands into bus-level signals and converts received bus activity back into logic. The TLE8250GVIOXUMA1 provides this physical-layer function in a surface-mount package suitable for automotive, industrial, and embedded control systems.

Key electrical features include operation from 4.5 V to 5.5 V, a maximum supported data rate of 1 Mbaud, and 200 mV receiver hysteresis. The hysteresis helps the receiver distinguish signaling states in the presence of bus noise. Infineon also identifies the TLE8250GVIO family as a high-speed, ISO 11898-2-compliant CAN transceiver with low electromagnetic emissions and high electromagnetic immunity.

The device is positioned as a successor-generation HS CAN transceiver and is described as pin and function compatible with the preceding TLE6250GV33. Its half-duplex architecture allows a node to transmit and receive on the same CAN bus through CANH and CANL. Logic-side control and reporting are separated from the differential bus interface, allowing an MCU, automotive communications controller, or industrial CAN controller to connect without adding discrete bus-driver circuitry.

Typical applications include automotive body and powertrain electronics, industrial automation controllers, electric-vehicle subsystems, building automation gateways, CAN-connected sensors, and embedded motor-control systems. A CAN node using the TLE8250GVIOXUMA1 can operate at rates up to 1 Mbaud while benefiting from the family’s low EMI emissions and high EMI robustness.

When designing the PCB around this transceiver, place the device near the CAN connector or bus header to minimize exposed high-frequency bus traces. Keep CANH and CANL routing symmetrical, provide the bus-side network recommended by the manufacturer, and maintain a clean ground return. Verify transceiver logic levels, supply tolerance, pin compatibility, and bus termination independently before replacing another CAN interface device.

This product page combines the manufacturer’s family-level specifications with practical application guidance, package information, sourcing questions, and a pin-compatible replacement analysis. These engineering-oriented details help designers evaluate the TLE8250GVIOXUMA1 for new CAN nodes, legacy replacements, and production-risk assessment without relying only on a catalog summary.

드롭인 대체품: TLE8250GVIOXUMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: TLE8250GVIOXUMA1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, RoHS Status, Supply Voltage Range.

Infineon
Package: PG-DSO-8
RoHS Status: RoHS compliant green product
Supply Voltage Range: 12 V to 24 V
비교 대상: TLE8250GVIOXUMA1 →

TLE6250GV33XUMA1

✅ 드롭인
Infineon
📦 PG-DSO-8-16
CAN bus transceiver · 1/1 half-duplex transceiver · 1 Mbit/s · 12 V to 24 V · 3.3 V to 5 V · 70 mA · 12 V and 24 V automotive battery systems · Normal mode and standby mode

가격 문의

데이터시트 보기 →

TLE8250GVIOXUMA5

✅ 드롭인
Infineon
📦 PG-DSO-8-16
CANbus · 1 MBd · 1/1 · Half · 4.5 V to 5.5 V · 200 mV · -40C to +150C · Surface Mount

가격 문의

데이터시트 보기 →

TJA1051T,118

✅ 드롭인
📦 PG-DSO-8-16
Cross-brand 1 Mbaud HS CAN replacement candidate; exact pin, timing, protection, and qualification differences are .

📋 참조 대체품 (카탈로그에 없음)

SN75451BD

✅ 드롭인
📦 PG-DSO-8-16
Cross-brand HS CAN interface candidate; exact pin, timing, standby, and bus-fault differences are .

📋 참조 대체품 (카탈로그에 없음)

SN75453BD

✅ 드롭인
📦 PG-DSO-8-16
Cross-brand HS CAN interface candidate with a 1 Mbaud-family function; exact pin and electrical differences are .

📋 참조 대체품 (카탈로그에 없음)

TLE8250GVIOXUMA1 사양

Product Type CAN bus transceiver
Transceiver Configuration 1 transmitter / 1 receiver
Duplex Mode Half-duplex
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 1 Mbaud
Receiver Hysteresis 200 mV
CAN Standard ISO 11898-2
패키지 PG-DSO-8-16
Terminal Count 8
실장 유형 Surface mount
Package Height 1.75 mm maximum
Lead Form Gull wing
Package Shape Rectangular
RoHS 상태 Compliant
Predecessor Compatibility Pin and function compatible with TLE6250GV33
Electromagnetic Emissions Low EME
Electromagnetic Immunity High EMI robustness

TLE8250GVIOXUMA1 rectangular 핀 구성 가이드

TLE8250GVIOXUMA1(rectangular 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

TLE8250GVIOXUMA1의 rectangular 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: TLE8250GVIOXUMA1.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

TLE8250GVIOXUMA1 적합 용도: 6 애플리케이션s: Automotive Body Control Modules, Industrial Automation Controllers, Electric Vehicle Subsystems, Building Automation Gateways, CAN-Connected Sensor Hubs, Embedded Motor-Control Systems.

🚗

Automotive Body Control Modules

The TLE8250GVIOXUMA1 fits automotive body-control and comfort modules that use a 5 V CAN physical layer. Its 4.5 V to 5.5 V supply range supports regulated 5 V electronics, while operation up to 1 Mbaud allows it to participate in faster CAN segments when topology and cable length permit. The 200 mV receiver hysteresis improves noise tolerance, and the family’s low EME and high EMI robustness are valuable in electrically demanding vehicles. Place the transceiver near the CAN connector, maintain a continuous ground reference, and verify automotive temperature and qualification requirements against the exact ordering code before production release.

🏭

Industrial Automation Controllers

The TLE8250GVIOXUMA1 is suitable for PLCs, factory controllers, and remote I/O nodes connected through a high-speed CAN bus. Its ISO 11898-2 physical-layer compliance, 1 Mbaud capability, and half-duplex architecture align with common industrial CAN networks. A 200 mV receiver hysteresis helps the node recognize valid differential states in electrically noisy factory environments. The 8-pin PG-DSO-8-16 package also keeps the bus interface compact. Confirm the operating-temperature range, bus-fault exposure, termination strategy, isolation needs, and equipment-level EMC requirements before integrating it into machinery-control electronics.

⚡

Electric Vehicle Subsystems

The TLE8250GVIOXUMA1 can connect high-speed CAN networks used by electric-vehicle supervisory, body, thermal-management, or charging subsystems. Its 4.5 V to 5.5 V operating range matches common low-voltage digital rails, and the 1 Mbaud capability supports faster communication segments than lower-speed CAN devices. Low electromagnetic emissions help reduce interference within the vehicle, while high EMI robustness supports operation in a challenging electrical environment. Use short, symmetrical CANH and CANL routing, preserve the ground connection, and validate the complete power and fault conditions required by the vehicle platform.

🧩

Building Automation Gateways

The TLE8250GVIOXUMA1 is appropriate for building-automation gateways, room controllers, and energy-management nodes that connect embedded controllers to a CAN-based sensor network. Its half-duplex 1/1 configuration and 1 Mbaud rate provide adequate bandwidth for control traffic, while the 200 mV receiver hysteresis assists reliable reception in installations with nearby motors and switching equipment. The compact 8-pin surface-mount package simplifies dense controller layouts. Validate temperature performance, bus protection, grounding, shield termination, and the network’s timing budget before deploying it in building controls.

🌐

CAN-Connected Sensor Hubs

The TLE8250GVIOXUMA1 can serve as the bus interface in a multi-sensor acquisition hub for environmental monitoring, condition monitoring, or industrial sensing. A 1 Mbaud CAN rate permits timely collection of measurements from multiple nodes, and ISO 11898-2 compliance supports standardized physical-layer behavior. The 200 mV receiver hysteresis improves tolerance of local noise from sensors and relays. Because many sensor hubs operate from constrained 5 V rails, the 4.5 V to 5.5 V supply range is also useful. Confirm startup behavior, bus standby requirements, fault recovery, and environmental limits for the installation.

🔧

Embedded Motor-Control Systems

The TLE8250GVIOXUMA1 is useful in embedded motor-control and actuator nodes that exchange commands and diagnostics over a CAN network. Its 1 Mbaud capability supports responsive communication, while half-duplex operation allows transmission and reception over the same differential bus. The 200 mV receiver hysteresis helps distinguish valid messages when motor drives, relays, and power stages introduce electrical noise. The 8-pin PG-DSO-8-16 package minimizes board area beside a controller and driver circuitry. Verify operating temperature, isolation, bus protection, grounding, and shutdown behavior against the motor-drive system requirements.

추천 제품 요약

TJA1051T,118 Cross-brand high-speed CAN transceiver candidate 사용처: Automotive Body Control Modules, Electric Vehicle Subsystems, Embedded Motor-Control Systems TLE6250GV33 Pin- and function-compatible Infineon predecessor 사용처: Automotive Body Control Modules, CAN-Connected Sensor Hubs AT90CAN64-16MUR Microchip Technology 사용처: Automotive Body Control Modules, Industrial Automation Controllers, Building Automation Gateways, CAN-Connected Sensor Hubs TCAN334DCNT Texas Instruments 사용처: Industrial Automation Controllers, Electric Vehicle Subsystems TCAN330DCNR Texas Instruments 사용처: Industrial Automation Controllers, CAN-Connected Sensor Hubs TLE8250GVIOXUMA5 Infineon 사용처: Electric Vehicle Subsystems, Embedded Motor-Control Systems SN75451BD Cross-brand CAN interface candidate 사용처: Building Automation Gateways SN75453BD Cross-brand CAN interface candidate 사용처: Building Automation Gateways MC33215BE NXP Semiconductors 사용처: Embedded Motor-Control Systems
What is the TLE8250GVIOXUMA1?
The TLE8250GVIOXUMA1 is an Infineon Technologies high-speed CAN transceiver with one transmitter and one receiver in an 8-pin PG-DSO-8-16 package. According to the Infineon TLE8250GVIO product page, it is ISO 11898-2 compliant, supports data rates up to 1 Mbaud, and is intended for half-duplex CAN bus communication. The device operates from a 4.5 V to 5.5 V supply.
What is the operating voltage of TLE8250GVIOXUMA1?
The TLE8250GVIOXUMA1 operates from 4.5 V to 5.5 V. The manufacturer product information identifies this range for the TLE8250GVIO high-speed CAN transceiver family. A common-mode or transient bus fault can exceed the normal supply operating range, so the complete system must still satisfy the limits and protection requirements stated in the manufacturer datasheet.
What is the maximum CAN data rate of TLE8250GVIOXUMA1?
The TLE8250GVIOXUMA1 supports CAN communication at up to 1 Mbaud. Infineon describes the TLE8250GVIO as a high-speed CAN transceiver that fulfills or exceeds ISO 11898-2 requirements. Actual bus performance also depends on cable length, topology, termination, oscillator accuracy, transceiver loop delay, and the CAN controller configuration.
Where can I download the TLE8250GVIOXUMA1 datasheet PDF?
The official TLE8250GVIO manufacturer page is the appropriate starting point for the TLE8250GVIOXUMA1 datasheet and ordering information. A separate TLE8250GVIOXUMA1 PDF is also listed by DiGi-Electronics. Review the pin-description table, recommended application circuit, electrical characteristics, and package drawing in the manufacturer documentation before laying out or qualifying a replacement.
Where can I find the TLE8250GVIOXUMA1 pinout?
Use the pin-description table and top-view package drawing in the Infineon TLE8250GVIO documentation to determine the TLE8250GVIOXUMA1 pinout. The component is supplied in an 8-terminal PG-DSO-8-16 gull-wing surface-mount package. Confirm pin numbering against the exact package variant and verify CANH, CANL, VCC, GND, TXD, RXD, and any mode or enable connection before routing the PCB.
Is TLE8250GVIOXUMA1 ISO 11898-2 compliant?
Yes, the TLE8250GVIOXUMA1 is identified as ISO 11898-2 compliant, according to Infineon’s TLE8250GVIO product page. That standard applies to the high-speed CAN physical-layer interface. Compliance does not by itself guarantee correct operation on every bus, so the complete design must also satisfy bus timing, termination, wiring, fault-protection, and system-level EMC requirements.
What is the receiver hysteresis of TLE8250GVIOXUMA1?
The TLE8250GVIOXUMA1 receiver hysteresis is 200 mV. Infineon’s component description identifies this value as part of the device’s robust reception capability in noisy environments. Hysteresis helps prevent the receiver from switching repeatedly near a decision threshold, although proper differential routing, grounding, bus termination, and CAN controller filtering remain necessary for dependable network operation.
What can replace TLE8250GVIOXUMA1?
The TLE6250GV33 is the clearest replacement candidate because Infineon describes the TLE8250GVIO as pin and function compatible with its predecessor. Cross-brand candidates include TJA1051T,118, SN75451BD, and SN75453BD, each of which appears in comparative or cross-reference material. A replacement should still be checked for exact pinout, supply level, bus timing, standby behavior, fault protection, and qualification requirements.
Is TLE8250GVIOXUMA1 the same as TJA1051T,118?
No. TLE8250GVIOXUMA1 and TJA1051T,118 are both high-speed CAN transceivers from different manufacturers, but one is not automatically interchangeable with the other. Cross-reference material lists them for comparison, while exact substitution depends on pin-level connectivity, supply requirements, receiver output behavior, mode-control logic, loop delay, bus protection, and package-specific details.
TLE8250GVIOXUMA1 vs TJA1051T,118 — which is better for an automotive CAN node?
Choose TLE8250GVIOXUMA1 when its documented ISO 11898-2 compliance, 1 Mbaud operation, 200 mV receiver hysteresis, low EME, and high EMI robustness match the system requirements. Consider TJA1051T,118 when its own electrical, timing, protection, and qualification data are a better fit. The comparison source establishes a relationship, but it does not by itself prove full functional or qualification equivalence.
When should I choose TLE8250GVIOXUMA1 over TLE6250GV33?
Choose TLE8250GVIOXUMA1 for a new high-speed CAN design when its 4.5 V to 5.5 V supply range, 1 Mbaud capability, 200 mV receiver hysteresis, and low-EMI/high-EMI-robustness characteristics meet the specification. TLE6250GV33 is relevant when maintaining a proven predecessor design. Because Infineon states pin and function compatibility, both can support footprint reuse, subject to a complete electrical review.
Is TLE8250GVIOXUMA1 suitable for industrial automation equipment?
Yes, TLE8250GVIOXUMA1 is suitable for industrial CAN nodes when the application requires ISO 11898-2 high-speed physical-layer communication up to 1 Mbaud. Its 4.5 V to 5.5 V supply and 200 mV receiver hysteresis fit many 5 V embedded systems. Also verify operating-temperature limits, isolation requirements, EMC certification, bus fault exposure, and regulatory obligations for the finished equipment.
Where to buy TLE8250GVIOXUMA1 online?
Use the Request a Quote form on this page to request TLE8250GVIOXUMA1 availability, order quantity, and current lead time. The manufacturer identifies the part as an Infineon TLE8250GVIO family member with an 8-pin PG-DSO-8-16 package. Share the required quantity, date code, target packaging, and quality requirements with the quote request to obtain an actionable supply response.
What is the price of TLE8250GVIOXUMA1?
Use the Request a Quote form on this page for the current TLE8250GVIOXUMA1 price, quantity breaks, and supply status. Pricing depends on order quantity, date code, package configuration, and current market conditions. The product summary alone does not establish a stable unit price, so a current quotation is preferable to reproducing a transient catalog figure.
What is the lead time and stock status for TLE8250GVIOXUMA1?
Request the current TLE8250GVIOXUMA1 lead time and stock status through the Request a Quote form on this page. Include your required quantity, approved date codes, packaging preference, target delivery date, and quality requirements. A distributor landing page may show changing availability, so the quotation response is the appropriate basis for production planning.
What are the key specifications of TLE8250GVIOXUMA1 that engineers should know?
The key TLE8250GVIOXUMA1 specifications are a 4.5 V to 5.5 V supply range, operation up to 1 Mbaud, 200 mV receiver hysteresis, half-duplex 1/1 transceiver configuration, and an 8-pin PG-DSO-8-16 package. Infineon also identifies ISO 11898-2 compliance, low electromagnetic emissions, high electromagnetic immunity, and pin and function compatibility with the TLE6250GV33 predecessor.

엔지니어링 참조 데이터: TLE8250GVIOXUMA1 — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose TLE8250GVIOXUMA1 for a new half-duplex high-speed CAN node that requires ISO 11898-2 operation, a 4.5 V to 5.5 V supply, up to 1 Mbaud communication, 200 mV receiver hysteresis, and a compact 8-pin surface-mount interface. Choose TLE6250GV33 when maintaining a predecessor design because Infineon explicitly states pin and function compatibility with TLE8250GVIO. Consider TJA1051T,118, SN75451BD, or SN75453BD only after reviewing their exact pinout, timing, logic levels, standby behavior, protection, and qualification data. The target part is the stronger choice when its documented low-EMI, high-EMI-robustness characteristics and receiver hysteresis are central to the design. A cross-brand substitute may be preferable when its manufacturer-specific qualification, lifecycle position, sourcing, or protection features better satisfy the finished system. No replacement should be approved solely from the package name or a high-level CAN-transceiver description.

대체품과의 비교

파라미터 이 제품 TLE6250GV33 TLE8250GVIOXUMA5 TJA1051T,118 SN75451BD SN75453BD
Brand Infineon Technologies Infineon Technologies Infineon Technologies NXP Semiconductors Texas Instruments Texas Instruments
Package PG-DSO-8-16 PG-DSO-8-16 PG-DSO-8-16 PG-DSO-8-16 PG-DSO-8-16 PG-DSO-8-16
Product Type CAN transceiver CAN transceiver CAN transceiver CAN interface transceiver CAN interface transceiver CAN interface transceiver

주요 차별점

  • Explicit manufacturer-backed compatibility with the preceding CAN transceiver (vs TLE6250GV33)
  • Documented receiver hysteresis for noisy CAN networks (vs TJA1051T,118)
  • Low-emission and high-immunity family positioning (vs SN75451BD)
  • 4.5 V to 5.5 V operating range (vs SN75453BD)

설계 노트

Place the TLE8250GVIOXUMA1 close to the CAN connector or bus header and keep the CANH and CANL paths short, matched in geometry, and free of unnecessary stubs. Provide a low-impedance ground-plane connection and avoid routing bus signals beneath switching nodes or high-current return paths. The 8-pin PG-DSO-8-16 package supports compact placement, but its thermal and electrical performance still depends on a sound ground reference and the manufacturer’s recommended external network.

Treat CANH and CANL as a coupled differential pair. Match trace geometry and length where practical, maintain clearance from unrelated high-voltage or switching conductors, and use the termination and common-mode network specified for the complete bus topology. The TLE8250GVIOXUMA1 supports rates up to 1 Mbaud, but stable operation also depends on cable length, propagation delay, controller timing, node count, and termination placement.

Do not assume that a catalog cross-reference proves drop-in equivalence. Compare the exact pin-description table, TXD polarity, RXD output type, standby or enable state, supply range, bus-fault behavior, loop delay, and package drawing. TLE6250GV33 has explicit manufacturer support for pin and function compatibility with TLE8250GVIO, while cross-brand candidates require a full electrical and qualification review before substitution.

Use a continuous ground reference beneath and around the transceiver, decouple the 5 V supply locally, and keep switching-regulator and high-current paths away from CANH and CANL. The TLE8250GVIO family is characterized by low electromagnetic emissions and high electromagnetic immunity, but those characteristics support—not replace—a careful PCB design. Validate the completed product against the applicable system-level EMC requirements and the intended CAN network environment.

규정 준수 정보

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The component listing identifies the PG-DSO-8 package as RoHS compliant. ISO 11898-2 compliance applies to the CAN physical interface. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ordering code.

데이터 검증일: 2026-11-10 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

TLE8250GVIOXUMA1 datasheet TLE8250GVIOXUMA1 pinout TLE8250GVIOXUMA1 datasheet pdf TLE8250GVIOXUMA1 equivalent TLE8250GVIOXUMA1 replacement TLE8250GVIOXUMA1 cross reference TLE8250GVIOXUMA1 vs TJA1051T TLE8250GVIOXUMA1 price TLE8250GVIOXUMA1 stock Infineon TLE8250GVIOXUMA1 TLE8250GVIO PG-DSO-8 pinout TLE8250GVIO 1 Mbaud CAN application

관련 부품 & 용어

Infineon Technologies TLE8250GVIOXUMA1 TLE8250GVIO TLE8250GVIOXUMA5 TLE6250GV33 TJA1051T,118 SN75451BD SN75453BD CAN transceiver CAN bus high-speed CAN HS CAN ISO 11898-2 half-duplex transceiver interface IC physical-layer interface PG-DSO-8-16 SOIC-8 surface mount SMD 4.5 V to 5.5 V 1 Mbaud 200 mV receiver hysteresis low EME high EMI robustness RoHS AT90CAN64-16MUR TCAN334DCNT TCAN330DCNR
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기