উপশ্রেণী

পণ্য (46,000+)

TAS5162DDV - 210W Stereo Class-D Amplifier | Texas Instruments
TAS5162DDV

TAS5162DDV - 210W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TAS5162DDV is a two-channel Class-D digital audio power amplifier rated for 210 W per channel into a 6-ohm bridge-tied load at 10% total harmonic distortion. It accepts a 0 V to 52.5 V amplifier supply and 10.8 V to 13.2 V digital supply, uses a PWM input interface, and is packaged in a 44-pin HTSSOP with an exposed thermal pad for thermal management. A Class-D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an analog audio waveform. It belongs to the broader power-amplifier hierarchy and converts digital or PWM control signals into high-current bridge-tied speaker outputs. Compared with a linear amplifier, a properly implemented Class-D stage can deliver high output power with lower power dissipation, making it suitable for home theater, multichannel audio, powered speakers, and compact high-performance sound systems. The TAS5162DDV combines a 160 W stereo configuration with a 300 W mono capability in one integrated device. Each channel can deliver up to 210 W into 6 ohms at 10% THD, while the product page identifies improved protection, low integrated output noise, low THD+N without clipping, and low idle-power dissipation. Internal pull-up resistors on the shutdown and overtemperature-warning outputs can connect those signals to 3.3 V; external pull-ups support 5 V logic levels. As a digital power stage, the device combines PWM command processing with integrated output-driver circuitry and an exposed-pad thermal interface. The 44-pin HTSSOP package provides the electrical connections required for PWM audio input, clocking, control, fault signaling, power rails, ground, and differential speaker outputs. Because output energy is dissipated in the power stage, the exposed thermal pad and PCB copper area are central to maintaining reliable operation at high continuous output power. Typical uses include powered stereo speakers, home-theater amplifiers, multimedia speaker systems, active subwoofers, and high-output consumer audio equipment. The TAS5162 can also be configured for mono operation when greater output power is required. System designers should match the speaker impedance, supply capability, switching layout, and thermal design to the intended channel configuration. For PCB implementation, place input and power decoupling close to the relevant device pins, connect the exposed pad to a properly sized thermal plane, and keep high-current speaker outputs away from sensitive audio inputs. The manufacturer datasheet's pin-description table and typical application circuit should govern net assignment, output-filter design, and thermal-pad connection. This page organizes the TAS5162DDV's principal electrical ratings, protection features, application guidance, package information, and engineering trade-offs. It also highlights where pin-compatible substitutions require additional qualification rather than assuming that similar audio amplifiers are automatic board-level replacements.

RFQ যোগাযোগ
TAS5162DKD 2x210W Stereo Class-D Power Stage | Texas Instruments
TAS5162DKD

TAS5162DKD 2x210W Stereo Class-D Power Stage | Texas Instruments

The Texas Instruments TAS5162DKD is a two-channel stereo digital Class-D audio amplifier power stage capable of delivering up to 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N. It accepts a 0 V to 52.5 V supply, supports PWM input, and is packaged in a 36-pin HSSOP with an exposed pad. A Class-D audio power stage is a switching amplifier topology that efficiently converts PWM signals into high-current audio outputs. Compared with a linear amplifier, the Class-D architecture places the active device in the saturation and cutoff regions, reducing conduction dissipation and supporting high output power in a compact package. The TAS5162 integrates the stereo output stage, protection functions, and digital control interfaces required by powered speakers and multi-channel audio systems. Key capabilities include 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N, operation across a 0 V to 52.5 V supply range, and an improved protection system. The device is suitable for professional audio, consumer audio, home-theater equipment, powered speakers, and compact subwoofer systems. Its integrated digital power-stage architecture simplifies the output path while retaining flexible signal-control and fault-reporting functions. The TAS5162 accepts a PWM input signal and drives each output as a bridge-tied load, eliminating the need for output coupling capacitors when the specified load arrangement is used. Its integrated protection system is intended to improve reliability under normal overload and fault conditions. The exposed thermal pad must be connected to a suitable thermal and ground plane so heat can leave the package efficiently during high-power operation. Typical applications include 210 W stereo speaker amplifiers, bridged mono installations, powered bookshelf and floor-standing speakers, home-theater receivers, professional powered speakers, and subwoofer amplifiers. The 52.5 V maximum supply supports high rail voltage, but the power stage still requires careful thermal design, low-impedance PCB routing, suitable output filtering, and protection against transient overvoltage. The most important design consideration is power delivery at low impedance. Output-current capability, copper width, connector sizing, heat spreading, and the thermal resistance of the exposed pad all influence whether the amplifier can sustain its rated output continuously. Use the manufacturer power-stage application guidance and thermal data when selecting the power-supply capability, output filter, copper area, and enclosure ventilation. This product page consolidates the key TAS5162DKD specifications, package information, application guidance, sourcing path, and replacement assessment into one engineering-focused reference. It also identifies where additional datasheet data, pin-level details, and qualified alternatives are required before a board-level design is released.

RFQ যোগাযোগ
TAS5162DKDR 2x210W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)
TAS5162DKDR

TAS5162DKDR 2x210W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)

The Texas Instruments TAS5162DKDR is a two-channel stereo digital Class-D audio amplifier power stage capable of delivering up to 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N. It accepts a 0 V to 52.5 V supply, supports PWM input, and is packaged in a 36-pin HSSOP with an exposed pad. A Class-D audio power stage is a switching amplifier topology that efficiently converts PWM signals into high-current audio outputs. Compared with a linear amplifier, the Class-D architecture places the active device in the saturation and cutoff regions, reducing conduction dissipation and supporting high output power in a compact package. The TAS5162 integrates the stereo output stage, protection functions, and digital control interfaces required by powered speakers and multi-channel audio systems. Key capabilities include 210 W per channel into a 6 ohm bridge-tied load at 10% THD+N, operation across a 0 V to 52.5 V supply range, and an improved protection system. The device is suitable for professional audio, consumer audio, home-theater equipment, powered speakers, and compact subwoofer systems. Its integrated digital power-stage architecture simplifies the output path while retaining flexible signal-control and fault-reporting functions. The TAS5162 accepts a PWM input signal and drives each output as a bridge-tied load, eliminating the need for output coupling capacitors when the specified load arrangement is used. Its integrated protection system is intended to improve reliability under normal overload and fault conditions. The exposed thermal pad must be connected to a suitable thermal and ground plane so heat can leave the package efficiently during high-power operation. Typical applications include 210 W stereo speaker amplifiers, bridged mono installations, powered bookshelf and floor-standing speakers, home-theater receivers, professional powered speakers, and subwoofer amplifiers. The 52.5 V maximum supply supports high rail voltage, but the power stage still requires careful thermal design, low-impedance PCB routing, suitable output filtering, and protection against transient overvoltage. The most important design consideration is power delivery at low impedance. Output-current capability, copper width, connector sizing, heat spreading, and the thermal resistance of the exposed pad all influence whether the amplifier can sustain its rated output continuously. Use the manufacturer power-stage application guidance and thermal data when selecting the power-supply capability, output filter, copper area, and enclosure ventilation. This product page consolidates the key TAS5162DKDR specifications, package information, application guidance, sourcing path, and replacement assessment into one engineering-focused reference. It also identifies where additional datasheet data, pin-level details, and qualified alternatives are required before a board-level design is released.

RFQ যোগাযোগ
TAS5176DDW - 6-Ch 100W Class-D Stage | Texas Instruments
TAS5176DDW

TAS5176DDW - 6-Ch 100W Class-D Stage | Texas Instruments

Texas Instruments TAS5176DDW is a six-channel, 100-W digital-amplifier power stage with PWM input, designed for 5.1-channel audio systems and configured for a 0-V to 34-V supply in a 44-pin HTSSOP package. Its six integrated output channels support multichannel Class-D amplification while the 10.8-V to 13.2-V PWM operating range provides a defined supply window for the power stage. A Class-D amplifier is a switching audio power amplifier whose output stage operates in a PWM state rather than continuously conducting a linear signal. This architecture belongs to the amplifier IC category and reduces the power dissipated by the output devices compared with a linear amplifier of comparable output capability. The TAS5176 integrates six digital power channels into one package, making it suitable for home-theater receivers, active speakers, soundbars, and multichannel automotive audio systems. The primary headline specifications are six output channels, up to 100 W of power capability, and a 0-V to 34-V supply range. The device accepts PWM signals directly, allowing it to work with a digital audio processor or PWM-generating audio engine. Its HTSSOP package contains 44 pins and provides a high-channel-count solution without requiring six separate power packages. The power stage is also suitable for subwoofer use when individual channels are configured appropriately. Class-D amplification places strict demands on power-supply layout, switching-node control, and thermal management. The supply and ground connections must provide low-impedance paths for high switching currents, while the exposed thermal pad and PCB copper must remove heat effectively. Incorrect output-filter or speaker-load design can increase distortion and reduce protection margin, so the manufacturer datasheet configuration should govern component selection and board implementation. Typical applications include 5.1-channel home theater amplification, active multiway speakers, powered subwoofers, compact multimedia systems, and automotive entertainment systems. An external digital audio processor can generate the PWM inputs, while the TAS5176 supplies the high-current channel drive. The six-channel arrangement also allows systems to combine several channels for higher-power BTL operation when the application and thermal design permit it. The principal design trade-off is the need for careful high-current layout and heat removal. Compared with a linear output stage, Class-D efficiency can reduce waste heat, but a 44-pin HTSSOP power package still requires careful attention to copper area, via arrays, thermal vias, and output filtering. Verify speaker impedance, supply capability, channel configuration, and maximum dissipated power before releasing a production layout. This page consolidates the exact orderable-device specifications, package information, application guidance, comparison fields, and engineering checks needed to evaluate TAS5176DDW. It also distinguishes confirmed technical facts from parameters that require confirmation in the full manufacturer datasheet before layout or production decisions.

RFQ যোগাযোগ
TAS5176DDWR - 6-Ch 100W Class-D Stage | Texas Instruments (Tape & Reel)
TAS5176DDWR

TAS5176DDWR - 6-Ch 100W Class-D Stage | Texas Instruments (Tape & Reel)

Texas Instruments TAS5176DDWR is a six-channel, 100-W digital-amplifier power stage with PWM input, designed for 5.1-channel audio systems and configured for a 0-V to 34-V supply in a 44-pin HTSSOP package. Its six integrated output channels support multichannel Class-D amplification while the 10.8-V to 13.2-V PWM operating range provides a defined supply window for the power stage. A Class-D amplifier is a switching audio power amplifier whose output stage operates in a PWM state rather than continuously conducting a linear signal. This architecture belongs to the amplifier IC category and reduces the power dissipated by the output devices compared with a linear amplifier of comparable output capability. The TAS5176 integrates six digital power channels into one package, making it suitable for home-theater receivers, active speakers, soundbars, and multichannel automotive audio systems. The primary headline specifications are six output channels, up to 100 W of power capability, and a 0-V to 34-V supply range. The device accepts PWM signals directly, allowing it to work with a digital audio processor or PWM-generating audio engine. Its HTSSOP package contains 44 pins and provides a high-channel-count solution without requiring six separate power packages. The power stage is also suitable for subwoofer use when individual channels are configured appropriately. Class-D amplification places strict demands on power-supply layout, switching-node control, and thermal management. The supply and ground connections must provide low-impedance paths for high switching currents, while the exposed thermal pad and PCB copper must remove heat effectively. Incorrect output-filter or speaker-load design can increase distortion and reduce protection margin, so the manufacturer datasheet configuration should govern component selection and board implementation. Typical applications include 5.1-channel home theater amplification, active multiway speakers, powered subwoofers, compact multimedia systems, and automotive entertainment systems. An external digital audio processor can generate the PWM inputs, while the TAS5176 supplies the high-current channel drive. The six-channel arrangement also allows systems to combine several channels for higher-power BTL operation when the application and thermal design permit it. The principal design trade-off is the need for careful high-current layout and heat removal. Compared with a linear output stage, Class-D efficiency can reduce waste heat, but a 44-pin HTSSOP power package still requires careful attention to copper area, via arrays, thermal vias, and output filtering. Verify speaker impedance, supply capability, channel configuration, and maximum dissipated power before releasing a production layout. This page consolidates the exact orderable-device specifications, package information, application guidance, comparison fields, and engineering checks needed to evaluate TAS5176DDWR. It also distinguishes confirmed technical facts from parameters that require confirmation in the full manufacturer datasheet before layout or production decisions.

RFQ যোগাযোগ
TAS5182DCA - 100W Stereo Class-D Controller | Texas Instruments
TAS5182DCA

TAS5182DCA - 100W Stereo Class-D Controller | Texas Instruments

Texas Instruments TAS5182DCA is a 100 W stereo digital amplifier power-stage controller with PWM input, Class-D output, and support for up to 34 V supply voltage. The device is packaged in a 56-pin HTSSOP and is specified for an ambient temperature range of 0°C to 70°C. It is designed to control external power stages for stereo audio systems. A Class-D audio power-stage controller is a semiconductor that processes a digital audio input and generates PWM drive signals for external H-bridge transistors. Unlike a conventional analog-output audio amplifier, the controller leaves power amplification to external MOSFETs, allowing output capability to scale with the selected power stage. It belongs to the digital audio amplifier and power-management IC hierarchy. The TAS5182DCA supports stereo operation at up to 2 × 100 W RMS into a 6 Ω bridge-tied load when paired with an appropriate external power stage. Its typical total harmonic distortion plus noise is below 0.15% under the conditions identified in the manufacturer documentation. PWM input and a 0 V to 34 V supply range suit higher-power consumer and professional audio architectures. Because TAS5182DCA is a controller rather than a self-contained power amplifier, its realized output power depends on external transistors, gate-drive implementation, supply capability, layout, thermal management, and speaker impedance. The IC controls the digital audio path while the external power devices carry the loudspeaker current. This division improves flexibility compared with integrating the output transistors into the controller package. Typical uses include stereo loudspeaker systems, powered speakers, home-theater receivers, professional audio racks, and compact consumer audio products. The 56-HTSSOP package supports high-density PCB layouts, while the exposed thermal pad provides a thermal connection to the board copper. The 0°C to 70°C rating targets commercial ambient environments rather than extended industrial or automotive temperature ranges. Careful power-stage layout is essential because switching currents and gate-drive timing directly affect distortion, thermal performance, and EMI. Keep high-current power loops compact, provide local supply decoupling, use low-inductance gate-drive paths, and connect the thermal pad to an appropriately sized copper area. Select the external MOSFETs and output filter against the intended load and switching requirements. This product record combines the controller’s principal operating characteristics with application guidance, verified package information, and drop-in replacement analysis. It also distinguishes the IC’s fixed control function from the variable output power contributed by the external transistor stage, helping engineers evaluate the complete amplifier rather than relying on the nominal controller rating alone.

RFQ যোগাযোগ
TAS5182IDCA - 100W Stereo Class-D Audio Controller
TAS5182IDCA

TAS5182IDCA - 100W Stereo Class-D Audio Controller

The Texas Instruments TAS5182IDCA is a stereo digital amplifier power-stage controller rated for 2 × 100 W RMS output at 6 V in bridge-tied-load (BTL) configurations. The device provides two-channel Class-D control, supports external discrete MOSFET output stages, and is packaged in a 56-pin HTSSOP. Its typical total harmonic distortion plus noise is below 0.15% at 1 kHz, making it suitable for high-power home-theater and powered-subwoofer systems. A digital amplifier power-stage controller is an integrated circuit that interprets an audio input and generates gate-drive signals for external switching MOSFETs. Unlike a conventional analog audio power amplifier, the TAS5182IDCA places the high-voltage and high-current switching function in discrete transistors. This separates signal processing from power conversion, allowing the external MOSFET stage to determine much of the amplifier's voltage, current, thermal, and output-power capability. The controller therefore belongs to the Class-D amplifier, digital audio amplifier, power-management IC, and semiconductor hierarchy. The 2 × 100 W capability at 6 V describes controller-supported BTL operation rather than the output of an integrated monolithic power stage. Engineers must select suitable N-channel power MOSFETs, a power-supply arrangement, an output filter, and a thermal design that match the target impedance and enclosure. The low typical distortion figure makes the controller appropriate for music reproduction systems where audible waveform deviation should remain low across the audio band. The TAS5182 architecture is intended to work with discrete bridge-tied-load output stages. In each half-bridge, the controller drives the gates of the high-side and low-side MOSFETs with complementary signals. External LC output filtering converts the switched full-bridge waveform into a filtered analog output capable of driving a loudspeaker through a BTL network. Correct gate voltage, dead time, switching speed, and layout continuity are therefore essential to the controller's real-world performance. Typical uses include home-theater amplifiers, powered subwoofers, active loudspeakers, compact stereo systems, and other high-power Class-D audio products. The controller can also serve multi-channel systems when each stereo pair is assigned to separate channels. Compared with a monolithic amplifier, the discrete-MOSFET approach offers greater freedom in output-device selection, thermal partitioning, and power scaling, but it also increases design complexity and EMI sensitivity. PCB implementation requires short gate-drive loops, careful high-current return paths, a continuous output-filter ground reference, and separation between sensitive input and switching nodes. Place input, supply, and compensation components close to their associated pins. Use thermal vias beneath exposed-pad structures where applicable and verify the selected MOSFETs, inductor, and capacitor ratings against the intended 6 V BTL operating point. EMI filtering must be evaluated together with the switching layout rather than added only after enclosure testing. This product page combines the controller's verified power and distortion ratings with package information, application guidance, drop-in family comparisons, and practical PCB design notes. It is intended to accelerate engineering selection while making the system-level responsibilities of an external-MOSFET Class-D output stage explicit.

RFQ যোগাযোগ
TAS5186ADDV - 210W 6-Channel Class-D Amplifier | TI
TAS5186ADDV

TAS5186ADDV - 210W 6-Channel Class-D Amplifier | TI

The Texas Instruments TAS5186ADDV is a 210-W, six-channel digital power-stage Class-D audio amplifier with a 0-V to 34-V supply range, PWM input architecture, and a 44-pin HTSSOP (DDV) package. The device is designed for multichannel home-theater and powered-speaker systems where one amplifier IC can address a 5.1-channel audio signal chain. A Class-D digital power stage is an audio amplifier that uses pulse-width modulation to drive a switching output stage. Unlike a conventional linear audio amplifier, a Class-D stage can convert more of its input power into output power, reducing the amount of heat that must be removed from the amplifier assembly. The TAS5186A family integrates six output channels for compact multichannel audio systems. The TAS5186ADDV supports up to 210 W of total amplifier power, is characterized as a six-channel 30-W device, and can drive a 3-ohm load. Texas Instruments describes the power stage as capable of driving a single-ended subwoofer above 60 W at 10% THD+N. Its specified total harmonic distortion plus noise is 0.07%, making it suitable for consumer audio equipment where channel matching and low crossover distortion are important. The device accepts PWM control signals, allowing it to operate with a compatible digital audio modulator such as the TAS5086. This architecture separates audio decoding and modulation from power amplification. It also means the selected modulator must support the signal format, switching frequency, channel count, and control requirements expected by the TAS5186A family. Typical applications include 5.1-channel home-theater amplifiers, powered subwoofers, multichannel active speakers, and compact consumer audio receivers. Its 44-pin HTSSOP package supports surface-mount assembly, while the stated 0°C to 70°C operating range targets commercial indoor environments. Heat management remains important because sustained multichannel output can raise junction and PCB temperatures. For a robust design, follow the manufacturer datasheet when assigning the power, ground, PWM input, and thermal-pad connections. Place input and power-ground connections to minimize switching-current loops, use the recommended decoupling arrangement, and provide sufficient copper area under the exposed pad. Verify thermal performance across the highest expected channel load rather than relying only on nominal output power. This product page combines manufacturer specifications, application guidance, practical thermal and layout considerations, and directly documented family alternatives for engineers evaluating the TAS5186ADDV as the power stage of a multichannel Class-D audio system.

RFQ যোগাযোগ
TAS5186DDV - 6-Channel 210W Class D Power Stage | TI
TAS5186DDV

TAS5186DDV - 6-Channel 210W Class D Power Stage | TI

The Texas Instruments TAS5186DDV is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply. A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection. The TAS5186DDV provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output. Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design. Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits. Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions. This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.

RFQ যোগাযোগ
TAS5186DDVR - 6-Channel 210W Class D Power Stage | TI (Tape & Reel)
TAS5186DDVR

TAS5186DDVR - 6-Channel 210W Class D Power Stage | TI (Tape & Reel)

The Texas Instruments TAS5186DDVR is a six-channel Class D digital-amplifier power stage rated for 210 W total output power, with 105 dB A-weighted SNR, less than 0.05% THD+N at 1 W, and greater than 90% power-stage efficiency at 1 W into the recommended single-ended loads. The device is housed in a 44-terminal HTSSOP package and operates from a 10.8 V to 13.2 V supply. A Class D power stage is an audio-amplifier output circuit that switches its supply rails at high frequency to produce a filtered audio waveform. It belongs to the amplifier IC hierarchy, where a digital-input power stage removes the need for external analog audio-input circuitry when it is paired with a compatible audio codec or digital-audio processor. Its principal advantages are high conversion efficiency, compact implementation, and integration of speaker-output protection. The TAS5186DDVR provides six independent amplification channels for multichannel audio systems. Its published performance includes 105 dB A-weighted signal-to-noise ratio, THD+N below 0.05% at 1 W, and efficiency above 90% into recommended loads. Integrated protection covers undervoltage, overtemperature, overload, and short-circuit conditions, reducing the amount of discrete protection required around each speaker output. Digital inputs allow the amplifier to receive audio samples directly from an audio codec, DSP, or other digital-audio source. This architecture supports a compact signal chain and accurate channel synchronization. The 44-terminal HTSSOP package also provides a practical surface-mount footprint for multi-channel consumer and professional audio equipment, subject to careful thermal and layout design. Typical uses include powered speakers, soundbar amplifier boards, home-theater receiver power stages, active subwoofer systems, and compact multimedia speaker designs. Its six-channel architecture is particularly useful when one board must drive multiple surround-sound channels without implementing six separate discrete amplifier circuits. Designers should follow the manufacturer layout guidance for high-current speaker and power-ground paths, place the required decoupling capacitors close to the device, and verify copper area for thermal dissipation. Thermal performance depends on output power, channel utilization, load impedance, PCB copper, and ambient temperature, so a compact enclosure should be validated under worst-case multichannel conditions. This page combines the device's principal performance specifications, application guidance, design cautions, and identified pin-compatible family options for faster engineering selection. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning PCB nets and confirming thermal limits.

RFQ যোগাযোগ
TAS5261DKD - 315W Mono Class D Amplifier | Texas Instruments
TAS5261DKD

TAS5261DKD - 315W Mono Class D Amplifier | Texas Instruments

The Texas Instruments TAS5261DKD is a 315 W mono bridge-tied-load Class D digital amplifier power stage packaged in a 36-pin HSSOP. It is designed to drive 4- to 8-ohm speakers with low harmonic distortion, and its digital input architecture requires a simple passive demodulation filter to produce high-quality, high-efficiency audio amplification. A Class D amplifier is a switching audio power stage whose output switches between the supply rails to amplify a pulse-width-modulated signal. After passive low-pass demodulation, this approach can provide high output power with lower power loss than a conventional linear audio amplifier. The TAS5261DKD belongs to the digital amplifier power-stage hierarchy, where an external input-processing stage generates the required modulation signal and the integrated power stage supplies current to the speaker load. The TAS5261DKD provides one mono amplification channel, supports 4- to 8-ohm speakers, and is identified as a 315 W mono BTL digital amplifier power stage. The manufacturer documentation also describes the device as a 400 W mono Class D amplifier, while the product-page description identifies a 315 W configuration. Its listed operating supply range is 10.8 V to 13.2 V. Digital inputs, short-circuit protection, and thermal protection are listed among the device features. The implementation uses a passive demodulation filter between the switching output and the speaker rather than an analog audio input stage. This architecture supports efficient amplification at relatively high output power, but the filter must be selected and laid out correctly because its response determines the recovered audio bandwidth, attenuation of carrier-related artifacts, and speaker-load stability. Typical uses include powered speakers, subwoofer amplifiers, professional audio equipment, consumer audio systems, and other mono loudspeaker applications operating from a 12 V-class supply. A bridge-tied-load configuration uses both output terminals to drive the speaker differentially, so the speaker remains connected between the two outputs rather than from one output to ground. PCB design should prioritize short power-stage connections, adequate thermal copper, a continuous supply path, careful grounding, and a stable reference return. The passive demodulation network should be placed close to the power-stage output, and its component values must follow the manufacturer reference design. Adequate copper area is important because Class D output current and supply transients can create losses, voltage drops, and EMI coupling even when the amplifier operates efficiently. This page combines the identified electrical ratings, package characteristics, application guidance, and manufacturer documentation links for engineering evaluation. It also distinguishes verified product facts from unspecified details so designers can consult the pin-description table, reference schematic, thermal guidance, and power calculations before committing a TAS5261DKD design to production.

RFQ যোগাযোগ
TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments
TAS5261DKDR

TAS5261DKDR - 315W Mono Class D Power Stage | Texas Instruments

The Texas Instruments TAS5261DKDR is a 315 W mono bridged-load-tie class D digital power stage packaged in a 36-terminal HSSOP. It is designed for high-efficiency audio amplification where a compact solution must deliver substantial continuous output power to a low-impedance loudspeaker. The device accepts digital audio data and operates as a mono class D output stage, supporting compact consumer and professional audio systems. A class D power stage is a switching amplifier topology that controls current through the speaker output at high frequency. Compared with a linear audio amplifier, the switching approach reduces the power dissipated in the output devices and enables high output power with smaller magnetic components. In the wider power-management hierarchy, the TAS5261 belongs to the class D amplifier family, which falls under audio amplifier ICs and, more broadly, power management semiconductors. Key characteristics include 315 W rated mono output power, a single-channel class D architecture, a 36-HSSOP package, and a bridged-load-tie speaker configuration. The HSSOP package uses a gull-wing surface-mount form factor and exposes a thermal pad for heat removal when the device is mounted according to the manufacturer's recommended land pattern. Its operating voltage, output-stage limits, thermal characteristics, and signal-interface timing should be confirmed against the specific version of the manufacturer datasheet before layout release. Typical implementations include powered speakers, compact home-theater enclosures, soundbars, multimedia speaker systems, subwoofer amplifier modules, and industrial audio products driven by an external audio processor. Because the device is a power stage rather than a complete codec-equipped amplifier, upstream circuitry must supply the required digital audio stream and control signals. A properly designed LC output filter is required to remove high-frequency switching energy before the loudspeaker. Layout is the dominant design consideration. Place the input, control, power, and output-network connections according to the datasheet reference layout, minimize loop area in high-current switching paths, and provide substantial copper area for thermal dissipation. Verify junction temperature at worst-case supply voltage, output power, and ambient temperature rather than relying on nominal board temperature alone. This page adds application-focused implementation guidance, pin-compatible sourcing information, and a structured comparison of the documented operating characteristics. Use the manufacturer datasheet and reference layout as the controlling documents for production design, EMC tuning, and thermal validation.

RFQ যোগাযোগ
TAS5342DDV - 100W Stereo Class D Power Stage | Texas Instruments
TAS5342DDV

TAS5342DDV - 100W Stereo Class D Power Stage | Texas Instruments

Texas Instruments TAS5342DDV is a 100-W stereo digital amplifier power stage designed for Class D audio systems, supplied in a 44-HTSSOP package. The device is intended for stereo or bridge-tied-load (BTL) configurations and supports speaker loads up to 8 ohm. Its integrated digital power-stage design is intended to provide high output power with low harmonic distortion, low integrated noise, and low idle current for audio receivers, powered speakers, soundbars, and other compact audio systems. A digital Class D power stage is a semiconductor amplifier category that converts a digital audio signal into a high-current switching waveform and then reconstructs the audio output through the speaker and output filtering network. Within the power-management hierarchy, the TAS5342DDV combines an audio amplifier, power conversion function, output-driver capability, and integrated fault protection in one power-management IC. It is commonly paired with an audio DSP or digital-audio interface that generates the required PWM signals. The TI product page identifies the TAS5342 as a high-performance integrated stereo digital amplifier power stage capable of driving a bridge-tied load at up to 100 W per channel. The listed operating power-supply range is 0 V to 34 V, with a typical supply range of 10.8 V to 13.2 V. The device supports differential input and differential output arrangements, which help reject common-mode noise and allow flexible speaker-routing configurations. The integrated protection system is a major functional feature. Texas Instruments describes protection against multiple fault conditions, including output-related faults that could otherwise damage the power stage or connected speaker network. The 44-HTSSOP package provides a high pin count for power connections, signal routing, control functions, and thermal management. Because power amplifiers dissipate energy in their output stages, correct copper area, thermal-pad layout, heat spreading, and enclosure ventilation are essential in practical designs. Typical applications include powered stereo speakers, home-theater receivers, compact soundbars, multimedia speakers, and other consumer audio equipment. The 100-W-per-channel capability is useful when the loudspeaker load is nominally 8 ohm and the amplifier is operated within the manufacturer-recommended supply and thermal limits. The differential output structure also makes the device suitable for BTL speaker connections, where each channel drives the speaker differentially. For implementation, follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning the 44-HTSSOP land pattern. Keep the power-stage supply and output-current paths compact, provide adequate input and output filtering, and confirm that the exposed thermal pad is connected to the intended ground and copper area. The amplifier should not be selected solely by its headline wattage; speaker impedance, supply voltage, thermal dissipation, modulation scheme, and output-filter requirements determine the practical result. This page summarizes the key electrical, packaging, protection, and application characteristics of the TAS5342DDV and organizes them for faster design review. It also identifies the limits of directly replacing a power-stage IC: a valid drop-in candidate must match the package, pinout, supply assumptions, output architecture, and thermal requirements rather than merely share a similar wattage rating.

RFQ যোগাযোগ
TAS5342DDVR - 100W Stereo Class D Power Stage | Texas Instruments (Tape & Reel)
TAS5342DDVR

TAS5342DDVR - 100W Stereo Class D Power Stage | Texas Instruments (Tape & Reel)

Texas Instruments TAS5342DDVR is a 100-W stereo digital amplifier power stage designed for Class D audio systems, supplied in a 44-HTSSOP package. The device is intended for stereo or bridge-tied-load (BTL) configurations and supports speaker loads up to 8 ohm. Its integrated digital power-stage design is intended to provide high output power with low harmonic distortion, low integrated noise, and low idle current for audio receivers, powered speakers, soundbars, and other compact audio systems. A digital Class D power stage is a semiconductor amplifier category that converts a digital audio signal into a high-current switching waveform and then reconstructs the audio output through the speaker and output filtering network. Within the power-management hierarchy, the TAS5342DDVR combines an audio amplifier, power conversion function, output-driver capability, and integrated fault protection in one power-management IC. It is commonly paired with an audio DSP or digital-audio interface that generates the required PWM signals. The TI product page identifies the TAS5342 as a high-performance integrated stereo digital amplifier power stage capable of driving a bridge-tied load at up to 100 W per channel. The listed operating power-supply range is 0 V to 34 V, with a typical supply range of 10.8 V to 13.2 V. The device supports differential input and differential output arrangements, which help reject common-mode noise and allow flexible speaker-routing configurations. The integrated protection system is a major functional feature. Texas Instruments describes protection against multiple fault conditions, including output-related faults that could otherwise damage the power stage or connected speaker network. The 44-HTSSOP package provides a high pin count for power connections, signal routing, control functions, and thermal management. Because power amplifiers dissipate energy in their output stages, correct copper area, thermal-pad layout, heat spreading, and enclosure ventilation are essential in practical designs. Typical applications include powered stereo speakers, home-theater receivers, compact soundbars, multimedia speakers, and other consumer audio equipment. The 100-W-per-channel capability is useful when the loudspeaker load is nominally 8 ohm and the amplifier is operated within the manufacturer-recommended supply and thermal limits. The differential output structure also makes the device suitable for BTL speaker connections, where each channel drives the speaker differentially. For implementation, follow the pin-description table and recommended application circuit in the manufacturer datasheet when assigning the 44-HTSSOP land pattern. Keep the power-stage supply and output-current paths compact, provide adequate input and output filtering, and confirm that the exposed thermal pad is connected to the intended ground and copper area. The amplifier should not be selected solely by its headline wattage; speaker impedance, supply voltage, thermal dissipation, modulation scheme, and output-filter requirements determine the practical result. This page summarizes the key electrical, packaging, protection, and application characteristics of the TAS5342DDVR and organizes them for faster design review. It also identifies the limits of directly replacing a power-stage IC: a valid drop-in candidate must match the package, pinout, supply assumptions, output architecture, and thermal requirements rather than merely share a similar wattage rating.

RFQ যোগাযোগ
TAS5352DDV 125W Stereo Class-D Power Stage | Texas Instruments
TAS5352DDV

TAS5352DDV 125W Stereo Class-D Power Stage | Texas Instruments

The Texas Instruments TAS5352DDV is an integrated stereo digital Class-D amplifier power stage designed to drive a 4 ohm bridge-tied load at up to 125 W per channel. It operates from a 10.8 V to 13.2 V supply and is packaged in a 44-pin HTSSOP with an exposed thermal pad. The device provides a high-efficiency speaker-drive solution with low harmonic distortion, low integrated noise, and low idle current. A digital Class-D audio power amplifier is a power-management IC that switches its output stage rapidly between voltage states to reproduce an audio waveform. Its efficiency is generally higher than that of a conventional linear amplifier because the switching stage dissipates less power when driving a speaker load. Bridge-tied-load operation applies the audio waveform across the two speaker terminals, increasing the available output voltage and power without requiring a physical ground connection at the speaker. The TAS5352DDV integrates a stereo output stage and a complete on-chip protection system. Its principal output rating is 125 W per channel into a 4 ohm BTL load, while its listed operating supply range is 10.8 V to 13.2 V. The device is specified for low harmonic distortion and low integrated noise, making it suitable for compact high-power audio systems. Its low idle current can also reduce standby dissipation when the associated system power architecture requires low quiescent consumption. TAS5352 is positioned as a power stage rather than a complete audio input amplifier. A practical system therefore needs a source capable of supplying the appropriate input signal, control or codec circuitry where required, output filtering, and a correctly designed speaker network. The manufacturer documents internal pull-up resistors to 3.3 V on the SD and OTW outputs; external pull-up resistors can provide 5 V logic level compliance where that interface voltage is required. Typical uses include powered speakers, compact home-theater systems, professional audio equipment, soundbars, subwoofer power modules, and other high-efficiency speaker-drive products. A 10.8 V to 13.2 V supply is particularly compatible with systems organized around a 12 V rail, although final rail limits, startup behavior, current demand, and protection requirements must be evaluated against the complete amplifier design. Thermal design is central to achieving the 125 W per-channel rating. The exposed-pad HTSSOP construction requires a low-impedance PCB thermal path, adequate copper area, and suitable airflow or enclosure heat transfer. Decoupling capacitors must be placed close to the supply and ground pins, and output-filter layouts must keep high-current switching paths compact. Speaker wiring, connectors, and load selection must also support the intended channel power. This page consolidates the verified device identity, package information, operating limits, interface details, and drop-in assessment into an engineering-focused reference. It also distinguishes documented functional similarity from true pin-to-pin equivalence, helping designers avoid treating a related part as an automatic replacement without completing a footprint, signal, control, and thermal review.

RFQ যোগাযোগ
TAS5352DDVR 125W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)
TAS5352DDVR

TAS5352DDVR 125W Stereo Class-D Power Stage | Texas Instruments (Tape & Reel)

The Texas Instruments TAS5352DDVR is an integrated stereo digital Class-D amplifier power stage designed to drive a 4 ohm bridge-tied load at up to 125 W per channel. It operates from a 10.8 V to 13.2 V supply and is packaged in a 44-pin HTSSOP with an exposed thermal pad. The device provides a high-efficiency speaker-drive solution with low harmonic distortion, low integrated noise, and low idle current. A digital Class-D audio power amplifier is a power-management IC that switches its output stage rapidly between voltage states to reproduce an audio waveform. Its efficiency is generally higher than that of a conventional linear amplifier because the switching stage dissipates less power when driving a speaker load. Bridge-tied-load operation applies the audio waveform across the two speaker terminals, increasing the available output voltage and power without requiring a physical ground connection at the speaker. The TAS5352DDVR integrates a stereo output stage and a complete on-chip protection system. Its principal output rating is 125 W per channel into a 4 ohm BTL load, while its listed operating supply range is 10.8 V to 13.2 V. The device is specified for low harmonic distortion and low integrated noise, making it suitable for compact high-power audio systems. Its low idle current can also reduce standby dissipation when the associated system power architecture requires low quiescent consumption. TAS5352 is positioned as a power stage rather than a complete audio input amplifier. A practical system therefore needs a source capable of supplying the appropriate input signal, control or codec circuitry where required, output filtering, and a correctly designed speaker network. The manufacturer documents internal pull-up resistors to 3.3 V on the SD and OTW outputs; external pull-up resistors can provide 5 V logic level compliance where that interface voltage is required. Typical uses include powered speakers, compact home-theater systems, professional audio equipment, soundbars, subwoofer power modules, and other high-efficiency speaker-drive products. A 10.8 V to 13.2 V supply is particularly compatible with systems organized around a 12 V rail, although final rail limits, startup behavior, current demand, and protection requirements must be evaluated against the complete amplifier design. Thermal design is central to achieving the 125 W per-channel rating. The exposed-pad HTSSOP construction requires a low-impedance PCB thermal path, adequate copper area, and suitable airflow or enclosure heat transfer. Decoupling capacitors must be placed close to the supply and ground pins, and output-filter layouts must keep high-current switching paths compact. Speaker wiring, connectors, and load selection must also support the intended channel power. This page consolidates the verified device identity, package information, operating limits, interface details, and drop-in assessment into an engineering-focused reference. It also distinguishes documented functional similarity from true pin-to-pin equivalence, helping designers avoid treating a related part as an automatic replacement without completing a footprint, signal, control, and thermal review.

RFQ যোগাযোগ
TAS5504APAG - 4-Channel Digital Audio PWM Processor | Texas Instruments
TAS5504APAG

TAS5504APAG - 4-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5504APAG is a four-channel digital audio PWM processor packaged in a 64-pin TQFP measuring 10 mm by 10 mm. It is designed to generate four independent Class-D audio output channels from digital audio data, combining digital signal processing, PWM modulation, and integrated audio output control in one device. A digital audio PWM processor is a specialized interface and signal-processing IC that converts digital audio samples into controlled PWM drive signals for power stages. In the broader power-management and audio-system hierarchy, it connects a digital audio source, such as a USB, network, or optical audio interface, to the PWM inputs of an external Class-D amplifier. The TAS5504A family therefore occupies the signal-generation stage between digital audio data and the analog power-amplifier output stage. The device's defining product features are its four-channel architecture, 64-pin TQFP package, and 10 mm by 10 mm body size. The manufacturer categorizes it as a digital audio PWM processor and as an audio modulator. Its four-channel structure allows one processor to manage multiple audio zones or paired amplifier channels while reducing the number of discrete control and modulation functions required in a multi-channel audio system. As a digital signal-processing and modulation device, the TAS5504A accepts digital audio information and applies embedded processing functions before producing PWM control waveforms for downstream power stages. This architecture allows audio-system design decisions to be centralized in the processor rather than distributed across separate digital-to-analog conversion, analog filtering, and modulation blocks. Exact signal formats, sampling rates, filter characteristics, clock requirements, and electrical limits must be confirmed in the manufacturer datasheet for the specific power-amplifier design. Typical applications include multi-channel home-theater and powered-speaker systems, active crossover networks, soundbars, professional audio equipment, and compact consumer-audio products. Its four-channel organization is particularly useful when two stereo amplifier channels must share one digital-audio source or when several independently controlled amplifier zones require synchronized digital modulation. The processor should be paired with an external Class-D output stage because it generates PWM control signals rather than directly delivering high-power speaker current. Layout is critical because digital clocking, PWM outputs, analog supply rails, and ground returns meet on a dense 64-pin surface-mount package. Keep high-current amplifier paths physically separate from the TAS5504APAG, use the manufacturer-recommended power and ground-plane arrangements, and provide local bypassing at the device supply pins. A solid return path and careful isolation of switching-node energy reduce the risk of audible artifacts or modulation instability. This page organizes the manufacturer device information, package characteristics, sourcing questions, application guidance, and confirmed same-footprint alternatives into a practical engineering reference. It also separates documented product facts from parameters that still require verification, helping designers decide when the TAS5504APAG is appropriate and what must be checked before committing a four-channel Class-D audio design to production.

RFQ যোগাযোগ
TAS5504PAG - 4-Channel Digital Audio PWM Processor | Texas Instruments
TAS5504PAG

TAS5504PAG - 4-Channel Digital Audio PWM Processor | Texas Instruments

Texas Instruments TAS5504PAG is a four-channel digital audio PWM processor with I2C and I2S interfaces, supplied in a 64-pin TQFP package measuring 10 mm by 10 mm. Its verified operating supply range is 3 V to 3.6 V, and the supported audio sampling-rate range is 32 kHz to 192 kHz. The processor is designed to accept digital audio data, perform configurable digital signal processing, and generate modulated outputs for downstream power stages. A digital audio PWM processor is a specialized signal-processing IC used to transform digital audio streams into control signals for power amplifiers and other audio output stages. Within the broader hierarchy, it belongs to digital signal processing, audio processing, and power-management interface components. Its digital architecture separates audio data conversion from the final analog power-amplifier stage, allowing digital controls and processing to operate before the signal reaches the power circuitry. The TAS5504PAG provides four independent audio channels and supports digital interfaces described in the verified distributor data as I2C and I2S. The I2S interface is used for serial audio data transfer, while I2C supports device configuration. The 32 kHz to 192 kHz range covers standard consumer-audio rates through high-resolution audio, making the processor applicable to multichannel audio systems that need centralized digital control. Its 64-TQFP package provides 64 connection positions for digital audio data, control, clocking, power, ground, and configuration signals. The 10 mm by 10 mm package is larger than a compact QFN but offers ample routing access for the numerous interfaces needed by a four-channel processor. A multilayer PCB with a low-impedance ground plane and short, terminated clock and data routes is appropriate when signal integrity is important. Typical applications include digital active speakers, multichannel audio amplifiers, home-theater amplification, soundbars, and compact consumer-audio systems. The processor can receive digital audio from a source or host processor and provide modulation data for a multi-channel amplifier stage. Compared with an analog-input-only controller, a digital architecture can preserve the source signal in digital form until power amplification. The primary design consideration is confirming that the host interface, audio data format, sample rate, channel mapping, and amplifier topology match the system requirements. The 3 V to 3.6 V supply range also requires regulators with suitable headroom and low-noise behavior. Decoupling capacitors should be positioned close to the supply and ground pins, while clock and I2S traces should be routed away from switching nodes. This page consolidates verified distributor specifications, current pricing references, same-package replacement candidates, and practical implementation guidance. It also distinguishes verified drop-in candidates from higher-channel-count devices that are not true pin-compatible replacements, helping engineers avoid an unqualified board-level substitution.

RFQ যোগাযোগ
TAS5504PAGR - 4-Channel Digital Audio PWM Processor | Texas Instruments (Tape & Reel)
TAS5504PAGR

TAS5504PAGR - 4-Channel Digital Audio PWM Processor | Texas Instruments (Tape & Reel)

Texas Instruments TAS5504PAGR is a four-channel digital audio PWM processor with I2C and I2S interfaces, supplied in a 64-pin TQFP package measuring 10 mm by 10 mm. Its verified operating supply range is 3 V to 3.6 V, and the supported audio sampling-rate range is 32 kHz to 192 kHz. The processor is designed to accept digital audio data, perform configurable digital signal processing, and generate modulated outputs for downstream power stages. A digital audio PWM processor is a specialized signal-processing IC used to transform digital audio streams into control signals for power amplifiers and other audio output stages. Within the broader hierarchy, it belongs to digital signal processing, audio processing, and power-management interface components. Its digital architecture separates audio data conversion from the final analog power-amplifier stage, allowing digital controls and processing to operate before the signal reaches the power circuitry. The TAS5504PAGR provides four independent audio channels and supports digital interfaces described in the verified distributor data as I2C and I2S. The I2S interface is used for serial audio data transfer, while I2C supports device configuration. The 32 kHz to 192 kHz range covers standard consumer-audio rates through high-resolution audio, making the processor applicable to multichannel audio systems that need centralized digital control. Its 64-TQFP package provides 64 connection positions for digital audio data, control, clocking, power, ground, and configuration signals. The 10 mm by 10 mm package is larger than a compact QFN but offers ample routing access for the numerous interfaces needed by a four-channel processor. A multilayer PCB with a low-impedance ground plane and short, terminated clock and data routes is appropriate when signal integrity is important. Typical applications include digital active speakers, multichannel audio amplifiers, home-theater amplification, soundbars, and compact consumer-audio systems. The processor can receive digital audio from a source or host processor and provide modulation data for a multi-channel amplifier stage. Compared with an analog-input-only controller, a digital architecture can preserve the source signal in digital form until power amplification. The primary design consideration is confirming that the host interface, audio data format, sample rate, channel mapping, and amplifier topology match the system requirements. The 3 V to 3.6 V supply range also requires regulators with suitable headroom and low-noise behavior. Decoupling capacitors should be positioned close to the supply and ground pins, while clock and I2S traces should be routed away from switching nodes. This page consolidates verified distributor specifications, current pricing references, same-package replacement candidates, and practical implementation guidance. It also distinguishes verified drop-in candidates from higher-channel-count devices that are not true pin-compatible replacements, helping engineers avoid an unqualified board-level substitution.

RFQ যোগাযোগ
TAS5508APAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5508APAG

TAS5508APAG - 8-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5508APAG is an 8-channel digital audio PWM processor for high-fidelity multichannel audio systems, housed in a 64-pin TQFP package measuring 10 x 10 mm. It supports sample rates from 32 kHz to 192 kHz and is categorized as a digital audio PWM processor and audio modulator. The device interfaces digital audio signals with external amplifier stages, providing centralized control for multichannel Class-D audio architectures. A digital audio PWM processor is a specialized interface IC that converts or prepares digital audio data for power-amplifier stages. It sits between an audio DSP, codec, or source controller and the power-amplifier output network. Within the signal chain, the hierarchy is digital audio processor, audio interface IC, PWM modulator, and power-management semiconductor. Integrating eight channels in one package reduces the number of separate control devices required for surround-sound and multichannel installations. The TAS5508APAG combines an 8-channel architecture with support for audio sample rates up to 192 kHz. This makes it appropriate for high-resolution consumer and professional audio systems operating at standard CD, DVD, multichannel cinema, and higher-rate digital audio sampling frequencies. Its 64-TQFP package provides a substantial number of external connections for digital audio data, clock signals, control signals, and power connections. The processor integrates digital control for eight audio output channels and is designed to operate with compatible digital signal processors and audio power stages. Automatic control configuration in response to clock and data conditions is associated with the TAS5508 family, helping the device adapt to changing digital-audio operating states. System designers should use the manufacturer pin-description table and reference circuit when assigning the complete 64-pin land pattern. Typical uses include 5.1-channel and 7.1-channel home-theater systems, professional digital mixing consoles, active speaker networks, automotive audio systems, and powered multiway speakers. The eight-channel architecture is particularly useful where a single DSP must distribute synchronized control across multiple Class-D amplifier channels. The device is also suitable for high-resolution installations operating with audio sample rates between 32 kHz and 192 kHz. Layout is critical because high-channel-count digital audio processors combine clock-sensitive signals with power-supply connections in a 10 x 10 mm TQFP footprint. Keep clock and data traces short, route them away from switching-node and power-converter traces, and place decoupling capacitors close to their associated supply pins. Follow the manufacturer’s recommended component values and pin-specific connection instructions to avoid signal-integrity problems. This page consolidates the device identity, package information, supported sample-rate range, sourcing information, compatible family references, and practical implementation guidance into one engineering-focused reference. It helps engineers separate confirmed product characteristics from details that require direct verification against the current Texas Instruments datasheet.

RFQ যোগাযোগ
TAS5508BPAG - 8-Channel Digital Audio PWM Processor | Texas Instruments
TAS5508BPAG

TAS5508BPAG - 8-Channel Digital Audio PWM Processor | Texas Instruments

The Texas Instruments TAS5508BPAG is an 8-channel digital audio PWM processor with I2C and serial digital-audio interfaces, designed for multichannel audio output systems. It operates from a 3 V to 3.6 V supply and is packaged in a 64-pin TQFP measuring 10 mm by 10 mm. Its eight-channel PWM architecture consolidates multiple audio output functions into one dedicated device while maintaining compatibility with conventional digital audio signal processors. An audio PWM processor is a specialized type of digital signal processor that accepts digital audio data and generates the pulse-width-modulated drive signals required by multi-channel Class-D audio output stages. Within the broader semiconductor hierarchy, it belongs to the digital signal processing family, then to audio DSPs, and ultimately to audio interface and power-management systems. The TAS5508BPAG is intended for systems that require more channels than a basic stereo audio interface can provide. The principal identified features are eight PWM output channels, a 3 V to 3.6 V operating supply range, I2C control support, a serial digital-audio interface, and a compact 64-pin TQFP package. These characteristics make the device applicable to home-theater receivers, active speakers, multichannel amplifiers, sound bars, and other systems requiring several synchronized digital audio output channels. The I2C interface supports configuration from a system controller, while the serial interface connects the processor to an upstream audio source. The integrated eight-channel PWM architecture reduces the number of separate digital audio output functions required in a multichannel design. Configuration is managed through digital control interfaces rather than discrete analog programming networks. Because the processor operates from a supply range extending down to 3 V, it can be paired with 3.3 V system logic. Its 10 mm by 10 mm TQFP package provides a standardized surface-mount footprint but requires careful thermal and layout planning during implementation. Typical audio-system uses include powered speakers, surround-sound receivers, active speaker arrays, multi-zone amplifiers, and digital mixing equipment. In each case, the processor occupies the digital control and PWM-generation stage before power amplification and speaker output. System designers must select an external power stage compatible with the device's voltage, current, timing, and output requirements. Use the manufacturer datasheet for the complete pin description, electrical limits, interface timing, recommended application circuit, and thermal information. A common implementation concern is ensuring that digital data, control signals, ground returns, and power-supply connections follow the specified layout because switching-edge energy from an audio system can affect signal integrity if routing is not controlled. This page combines the exact manufacturer and distributor listing details with application guidance, interface considerations, and verified same-package replacement information. It is intended to help engineers identify the correct device, locate its documentation, and assess whether a candidate replacement preserves the 64-pin TQFP footprint.

RFQ যোগাযোগ
TAS5508CPAG - 8-Channel PWM Processor | Texas Instruments
TAS5508CPAG

TAS5508CPAG - 8-Channel PWM Processor | Texas Instruments

Texas Instruments TAS5508CPAG is an 8-channel digital pulse-width modulation processor designed for advanced audio power amplification, with automatic control configuration in response to clock-rate, data-rate, and idle-state changes. The device is packaged in a 64-pin TQFP (PAG) package measuring 10 mm by 10 mm. A digital PWM processor is an audio-control and signal-generation IC that accepts digital audio information from an audio DSP and converts it into coordinated PWM outputs. Within the product hierarchy, it belongs to the digital signal processing and interface-controller family of semiconductors, where it bridges the digital audio source and a downstream power-amplifier or Class-D output stage. Its integration can reduce the number of separate timing, control, and output-routing functions required by a multichannel audio system. The headline characteristics of the TAS5508CPAG are eight processing channels, digital PWM operation, and a 64-pin TQFP package. Automatic adjustment of control configurations when clock or data rates change allows the processor to respond to changing source conditions without requiring the host system to reconfigure every output manually. Its idle-condition handling is also intended to simplify power-state behavior in audio equipment where channel activity changes frequently. The processor is designed to interface with most audio digital signal processors, creating a conventional separation between source decoding or sound processing and the final PWM control stage. That architecture is useful in multichannel home theater, powered speakers, sound bars, automotive audio, and professional listening equipment where multiple channels must remain synchronized while the input format, sample rate, or activity state changes. The integrated control approach also simplifies board partitioning compared with a design built from separate PWM-generation devices. The 64-pin PAG package provides the pin count needed for eight-channel operation, control signals, clocking, data interfaces, power connections, and ground routing. A 10 mm by 10 mm TQFP is surface-mountable and compatible with conventional PCB assembly and inspection processes. Designers should follow the manufacturer pin-description table and recommended application schematic when assigning tracks because clock, serial-data, and PWM routing must preserve timing and signal integrity. Use the TAS5508CPAG when a design needs an integrated eight-channel digital PWM control stage driven by an audio DSP. Validate clock topology, data-format compatibility, idle-state behavior, output configuration, and power sequencing against the manufacturer datasheet before layout release. Proper grounding and controlled clock routing are essential for repeatable multichannel performance and low conversion-related interference. This page organizes the TAS5508CPAG technical facts, sourcing routes, drop-in comparison limits, and practical design considerations into one engineering reference. It also distinguishes verified device capabilities from design parameters that must be confirmed in the manufacturer datasheet and application schematic.

RFQ যোগাযোগ
TAS5508PAG - 8-Channel Digital Audio PWM Processor | TI
TAS5508PAG

TAS5508PAG - 8-Channel Digital Audio PWM Processor | TI

Texas Instruments TAS5508PAG is an eight-channel digital audio PWM processor packaged in a 64-pin TQFP. It is designed to provide integrated digital-audio modulation for systems requiring eight simultaneous processing channels, precise timing, and coordinated signal generation. The manufacturer identifies the device as a PWM processor with eight digital channels, positioning it between general-purpose digital signal processing and a dedicated audio-class conversion controller. A digital audio PWM processor converts digital audio information into controlled pulse-width-modulated outputs for downstream power stages, amplifiers, or associated signal-chain functions. This device category belongs to the broader hierarchy of digital audio IC, audio signal processor, semiconductor, and embedded audio system. Its eight-channel architecture is intended to reduce the number of separate digital-to-audio modulation functions required in multi-channel amplification and audio-routing equipment. The TAS5508PAG combines eight-channel PWM processing with high system integration in its 64-pin TQFP package. The 64-pin package provides the external connections needed for multi-channel control, data exchange, configuration, clocking, and power connections. According to the manufacturer datasheet, the device supports eight simultaneous digital-audio channels, while the verified product descriptions consistently identify the TAS5508PAG as an eight-channel digital audio PWM processor. From a design perspective, channel synchronization and digital timing are central considerations because the processor coordinates multiple PWM outputs. Designers should preserve the data, clock, reset, control, and power topology shown in the manufacturer reference design and observe the recommended external-component values. Accurate layout, clean reference connections, and controlled clock routing help maintain consistent behavior across all eight channels and reduce sensitivity to noise or timing skew. Typical end uses include multichannel class-D audio amplification, powered speakers, home-theater equipment, active loudspeaker systems, and other multichannel audio products. In these systems, the TAS5508PAG can manage the digital audio modulation stage while external amplifier and output stages perform the required power conversion. The exact supported digital interface, sample-rate range, clock requirements, and channel operating modes should be confirmed from the manufacturer datasheet before schematic release. The primary design trade-off is integration versus board area: one 64-pin TQFP consolidates eight-channel processing but requires careful pin assignment, multilayer routing, and power-plane planning. Use the manufacturer pin-description table when assigning tracks, and use the datasheet evaluation-circuit and layout guidance when deriving a production PCB. This page summarizes the verified device identity and provides practical application, comparison, and sourcing guidance while clearly separating confirmed facts from parameters requiring datasheet confirmation.

RFQ যোগাযোগ
TAS5508PAGR - 8-Channel Digital Audio PWM Processor | TI (Tape & Reel)
TAS5508PAGR

TAS5508PAGR - 8-Channel Digital Audio PWM Processor | TI (Tape & Reel)

Texas Instruments TAS5508PAGR is an eight-channel digital audio PWM processor packaged in a 64-pin TQFP. It is designed to provide integrated digital-audio modulation for systems requiring eight simultaneous processing channels, precise timing, and coordinated signal generation. The manufacturer identifies the device as a PWM processor with eight digital channels, positioning it between general-purpose digital signal processing and a dedicated audio-class conversion controller. A digital audio PWM processor converts digital audio information into controlled pulse-width-modulated outputs for downstream power stages, amplifiers, or associated signal-chain functions. This device category belongs to the broader hierarchy of digital audio IC, audio signal processor, semiconductor, and embedded audio system. Its eight-channel architecture is intended to reduce the number of separate digital-to-audio modulation functions required in multi-channel amplification and audio-routing equipment. The TAS5508PAGR combines eight-channel PWM processing with high system integration in its 64-pin TQFP package. The 64-pin package provides the external connections needed for multi-channel control, data exchange, configuration, clocking, and power connections. According to the manufacturer datasheet, the device supports eight simultaneous digital-audio channels, while the verified product descriptions consistently identify the TAS5508PAGR as an eight-channel digital audio PWM processor. From a design perspective, channel synchronization and digital timing are central considerations because the processor coordinates multiple PWM outputs. Designers should preserve the data, clock, reset, control, and power topology shown in the manufacturer reference design and observe the recommended external-component values. Accurate layout, clean reference connections, and controlled clock routing help maintain consistent behavior across all eight channels and reduce sensitivity to noise or timing skew. Typical end uses include multichannel class-D audio amplification, powered speakers, home-theater equipment, active loudspeaker systems, and other multichannel audio products. In these systems, the TAS5508PAGR can manage the digital audio modulation stage while external amplifier and output stages perform the required power conversion. The exact supported digital interface, sample-rate range, clock requirements, and channel operating modes should be confirmed from the manufacturer datasheet before schematic release. The primary design trade-off is integration versus board area: one 64-pin TQFP consolidates eight-channel processing but requires careful pin assignment, multilayer routing, and power-plane planning. Use the manufacturer pin-description table when assigning tracks, and use the datasheet evaluation-circuit and layout guidance when deriving a production PCB. This page summarizes the verified device identity and provides practical application, comparison, and sourcing guidance while clearly separating confirmed facts from parameters requiring datasheet confirmation.

RFQ যোগাযোগ