উপশ্রেণী

📁 ADC/DAC 3,600+ পণ্যগুলি 📁 অ্যামপ্লিফায়ার IC 3,200+ পণ্যগুলি 📁 Analog Computation 0 পণ্যগুলি 📁 অডিও কোডেক 18 পণ্যগুলি 📁 অডিও IC 2 পণ্যগুলি 📁 ক্লক ও টাইমিং 970+ পণ্যগুলি 📁 Comparator ICs 1 পণ্যগুলি 📁 DSP 1,300+ পণ্যগুলি 📁 ডেটা অ্যাকুইজিশন IC 2 পণ্যগুলি 📁 ডিজিটাল পটেনশিওমিটার 4 পণ্যগুলি 📁 ডিসপ্লে ড্রাইভার ও কন্ট্রোলার 1 পণ্যগুলি 📁 FPGA ও CPLD 8,400+ পণ্যগুলি 📁 ইন্টারফেস IC 5,100+ পণ্যগুলি 📁 LED ড্রাইভার 1 পণ্যগুলি 📁 লজিক IC 720+ পণ্যগুলি 📁 মেমরি IC 870+ পণ্যগুলি 📁 মাইক্রোকন্ট্রোলার 22,000+ পণ্যগুলি 📁 মাইক্রোপ্রসেসর 4 পণ্যগুলি 📁 মোটর ড্রাইভার 1 পণ্যগুলি 📁 অন্যান্য 0 পণ্যগুলি 📁 সেন্সর এবং ডিটেক্টর ইন্টারফেস 1 পণ্যগুলি 📁 বিশেষায়িত IC 15 পণ্যগুলি 📁 ভিডিও IC 14 পণ্যগুলি

পণ্য (46,000+)

MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MAX350CPN+

MAX350CPN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

Analog Devices MAX350CPN+ is a dual 4:1 analog multiplexer with 100 ohm maximum on-resistance, housed in an 18-pin plastic DIP package. It combines two independently controlled 4:1 selectors, providing eight channels of analog routing while supporting bidirectional signal conduction. An analog multiplexer is an interface IC that connects one shared signal path to multiple inputs or one input to multiple outputs. The MAX350 belongs to the broader switch and multiplexer hierarchy, where low on-resistance, matched switch characteristics, and serial control are important for preserving signal integrity in test, measurement, and communication systems. The MAX350 family provides on-resistance matched between switches to 16 ohm maximum and flat to 10 ohm maximum over the specified signal range. Its 100 ohm maximum on-resistance suits low-frequency analog routing, while serial control reduces the number of control inputs required on a constrained board. The dual 4:1 organization allows two multiplexers to operate as independent routing pairs. The device supports continuous operation from dual supplies of ±2.7 V to ±8 V. It also supports a single-supply operating mode, although the complete single-supply limits must be confirmed in the manufacturer datasheet before final rail planning. Bidirectional conduction means the selected signal may travel into or out of the common terminal without changing the switch architecture. Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and communication equipment. In each case, the serial interface reduces control-line count while the matched low on-resistance helps minimize channel-dependent attenuation. The 18-pin DIP package is appropriate for through-hole prototype, legacy, and industrial assembly where surface-mount packaging is not required. When laying out a board, keep common and switched traces short, provide a solid ground reference, and route control signals away from sensitive analog paths. Confirm supply sequencing, logic-level thresholds, signal-range limits, and exposed-pin assignments against the manufacturer datasheet before manufacturing. This page combines manufacturer specifications, verified sourcing information, drop-in replacement analysis, application guidance, and design considerations to support component selection and PCB implementation.

RFQ যোগাযোগ
MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MAX350CWN+

MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

The Analog Devices MAX350CWN+ is a serially controlled, low-voltage dual 4:1 analog multiplexer with two independent 4:1 switch sections in an 18-pin wide SOIC package. Its maximum on-resistance is 100 ohm, with on-resistance matching between switches specified to 16 ohm maximum and flatness specified to 10 ohm maximum over the operating signal range. The device supports bidirectional signal conduction. A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact. The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package. On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required. Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths. PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication. This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.

RFQ যোগাযোগ
MAX350EPN - Dual 4:1 Multiplexer, 100Ω, 18-PDIP | Analog Devices
MAX350EPN

MAX350EPN - Dual 4:1 Multiplexer, 100Ω, 18-PDIP | Analog Devices

The Analog Devices MAX350EPN is a low-voltage, serially controlled analog multiplexer containing two 4:1 multiplexers, with a stated on-resistance of 100Ω, in an 18-pin PDIP package. The manufacturer identifies the MAX350 family as production, and the MAX350EPN is specified as a 2-circuit, 4:1 IC switch for routing multiple analog or digital signals through a shared interface. An analog multiplexer is a switch matrix that connects one of several inputs to an output under digital control. The MAX350EPN belongs to the dual 4-channel multiplexer segment of the broader interface IC hierarchy: analog switch → multiplexer → signal-routing IC. Its two independent 4:1 sections allow a controller to select among four sources per section while using a shared serial-control interface. This architecture is useful when a system must scan sensors, measurement channels, or test points without requiring a separate connector for every signal. The key documented characteristics are two switch circuits, a 4:1 configuration, 100Ω on-resistance, low-voltage operation, and an 18-pin PDIP package. The 100Ω resistance is appropriate for general-purpose low-frequency routing, although it introduces attenuation and distortion that must be considered when driving high-impedance versus low-impedance loads. The PDIP format also favors through-hole assembly and prototype or legacy-system repair rather than compact surface-mount production. Control is serial, allowing the multiplexer state to be changed by a microcontroller, test controller, or communications interface rather than by a separate parallel select line for each channel. Serial control can reduce the number of host-controller connections and simplify firmware-driven channel selection. Designers should still account for the control timing required to reach a valid output state before taking a measurement, particularly in high-speed sampling or automated test systems. Typical uses include multiplexed sensor acquisition, data-acquisition systems, industrial monitoring, test and measurement equipment, and embedded control systems with multiple low-bandwidth input channels. The part is especially relevant where two groups of four signals must share two common outputs. For higher-frequency or precision instrumentation, the system designer should compare channel capacitance, off leakage, bandwidth, and injection error against the complete MAX350 datasheet before finalizing the architecture. PCB planning should reserve the 18-pin PDIP footprint, provide a low-impedance ground reference, and route control traces away from sensitive analog paths. Keep switched-node traces short and use a continuous ground plane to reduce coupling. Confirm that downstream circuitry can tolerate the 100Ω series resistance and that the selected external resistors and amplifiers account for mux loading and switching transients. This product page combines the manufacturer’s MAX350 product information with distributor package details, application guidance, engineering caveats, and a transparent assessment of drop-in replacement availability. It also distinguishes documented MAX350EPN characteristics from parameters that still require verification from the complete manufacturer datasheet.

RFQ যোগাযোগ
MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices
MAX350EWN+

MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices

The Analog Devices MAX350EWN+ is a serially controlled, low-voltage CMOS analog multiplexer configured as two independent 4:1 switches in an 18-pin wide SOIC package. It operates from 2.7 V to 16 V and provides a maximum on-resistance of 100 ohm, with channel-to-channel matching limited to 16 ohm and resistance variation across the specified signal range limited to 10 ohm. The MAX350EWN+ conducts signal equally well in either direction, allowing it to route analog inputs or outputs through a serial interface. An analog multiplexer is a semiconductor that connects one signal path to one of several channels through controlled switches. The MAX350 family extends this category to the hierarchy of analog switch, multiplexer, routing IC, and signal-management semiconductor. Its 4:1 dual configuration provides two separately selectable channel groups, making it suitable for channel-scanning systems where multiple sensors, measurement inputs, or controlled outputs share a common signal chain. Key features include serial control, bidirectional signal conduction, low-voltage CMOS operation, and tightly matched switch resistance. The 100 ohm maximum on-resistance limits signal attenuation, while the 16 ohm maximum channel-to-channel match improves consistency when comparing readings across different channels. Its 18-pin wide SOIC package also provides a practical surface-mount footprint for industrial and instrumentation designs. The device uses a serial interface to select channels and control the multiplexers, reducing the number of package pins needed compared with a parallel-control multiplexer. This architecture is valuable in systems that route several slow or moderate-bandwidth analog signals, particularly when the microcontroller has limited general-purpose input/output capacity. Typical applications include multimeter and laboratory input switching, automated test equipment, data-acquisition modules, sensor-channel multiplexing, and control of multiple analog signal paths. The MAX350EWN+ is appropriate when bidirectional analog routing and matched resistance are more important than ultra-low on-resistance or high-speed video multiplexing. When laying out the circuit, keep analog traces short and connect the device to a stable low-noise supply. Confirm the serial interface levels and logic thresholds against the system controller, and verify that every switched signal remains within the specified analog input range. Check the full on-resistance and off-isolation characteristics in the manufacturer datasheet when the signal source is high impedance.

RFQ যোগাযোগ
MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices
MAX35103EHJ+

MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices

The Analog Devices MAX35103EHJ+ is a reduced-power time-to-digital converter with an integrated analog front end, real-time clock, and flash memory, specified for a 2.3 V to 3.6 V supply in a 32-pin TQFP (5 mm × 5 mm) package. It targets ultrasonic heat, water, and gas meters and increases the maximum time-of-flight measurement frequency in event timing mode from 2 Hz on the MAX35101 to 16 Hz. A time-to-digital converter, or ToF converter, measures the elapsed time represented by an ultrasonic pulse by converting a timing event into a digital result. The MAX35103 integrates the pulse-generation, receive-signal conditioning, timing, clock, and nonvolatile-measurement functions required by a compact ultrasonic metering front end. This integration reduces external circuitry compared with a discrete timer and analog receive chain while preserving a path to low-cost, low-power meter designs. According to the manufacturer datasheet, the MAX35103 consumes about half the average power of the MAX35101. The supplied sources do not provide a numeric average-current value, oscillator accuracy, ToF resolution, measurement range, flash capacity, temperature range, or absolute timing accuracy, so those values require confirmation in the datasheet or device evaluation before design release. The listed operating supply range is 2.3 V to 3.6 V. The integrated real-time clock and flash support metering designs that need timekeeping and persistent measurement data alongside ultrasonic time-of-flight conversion. The 16 Hz maximum event-timing frequency is particularly relevant when the meter must update more frequently than the MAX35101. Firmware, calibration, echo detection, and time-of-digital compensation still determine achievable accuracy and must be evaluated with real transducers and meter mechanics. Typical uses include ultrasonic heat meters, water meters, and gas meters. An Analog Devices evaluation kit installs the MAX35103EHJ+ and includes a USB-to-SPI interface plus graphical software for exercising device functionality. The supplied distributor records list the MAX35103EHJ+ in a 32-TQFP package and identify it as a CMOS-input, CMOS-output time-to-digital converter IC. For PCB design, place decoupling and timing-critical paths according to the manufacturer layout guidance and keep the ultrasonic analog front end away from switching nodes and digital return-current paths. Validate transducer drive amplitude, receive gain, threshold timing, clock calibration, and flash endurance under the intended flow, temperature, and supply conditions. Do not infer production suitability from the general-purpose EV kit alone.

RFQ যোগাযোগ
MAX351ESE+ - 35Ω Quad SPST Switch | Analog Devices
MAX351ESE+

MAX351ESE+ - 35Ω Quad SPST Switch | Analog Devices

The Analog Devices MAX351ESE+ is a precision, quad, SPST analog switch with a 1:1 signal configuration, 35Ω on resistance, and a 16-pin SOIC package. The four independent switch circuits are designed for routing low-frequency analog signals in test, measurement, instrumentation, and industrial control systems. Its industrial temperature grade supports operation from -40°C to +85°C. An analog switch is an electronic switching component that controls the connection between signal terminals with an external control input. As a normally closed SPST switch, the MAX351ESE+ provides a defined signal path when its control state does not request disconnection. The quad arrangement combines four switching functions in one package, reducing component count and simplifying routing in multi-channel systems. Within the broader hierarchy, it belongs to the analog switch and multiplexer family of interface ICs. The MAX351ESE+ uses a 35Ω on resistance and offers four 1:1 channels. These characteristics make it useful where moderate-resistance signal routing is acceptable and where compact, surface-mount packaging is preferred over discrete relay or transistor solutions. Its 16-pin SOIC form factor supports conventional PCB assembly and inspection processes. The device is specified as a precision analog switch rather than a high-speed digital multiplexer. Its SPST architecture simplifies each channel to one independently controlled conductive path. Design decisions should consider signal amplitude, acceptable insertion loss, source and load impedance, switching transients, and the control levels used by the surrounding logic. Typical uses include instrument signal selection, sensor-interface routing, analog test-point multiplexing, industrial control interfaces, and communication equipment. Four switch sections can manage several related channels without requiring four separate single-switch packages. The SOIC-16 outline also makes the device convenient for designs that already use standard analog and mixed-signal packages. For PCB implementation, route each switched node directly to its associated package pin and minimize loop area around sensitive analog traces. Confirm the control logic polarity, supply requirements, absolute maximum ratings, and recommended operating conditions in the manufacturer datasheet. Place bypass and signal-conditioning components where they can support low-impedance paths without creating unnecessary parasitic capacitance. This product page combines the manufacturer product description, exact-orderable-part listings, package details, temperature information, and practical routing guidance. It also identifies same-family drop-in candidates and highlights the electrical checks that must be completed before substituting a normally closed or low-leakage switch into a precision analog path.

RFQ যোগাযোগ
MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim
MAX352CPE+

MAX352CPE+ - 35Ω Quad SPST Analog Switch | Maxim

Analog Devices MAX352CPE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 35Ω, and a 16-pin PDIP package. The device supports analog signal switching over a 15V range and provides low off leakage of 250pA. Its four independent switches are intended for precision routing in data acquisition, test equipment, communication systems, and signal-processing circuits. An analog switch is a semiconductor device that routes analog electrical signals between input and output terminals under digital control. The MAX352 belongs to the analog switch hierarchy, where it functions as a four-channel SPST switching network. Unlike a relay or mechanical contactor, it offers compact integration, fast switching, and low off leakage, making it suitable for signals that must be switched repeatedly under digital system control. The MAX352 series provides low on resistance below 35Ω, with channel-to-channel matching maintained within 2Ω. On-resistance remains flat over the analog signal range, with a maximum variation of 3Ω. These characteristics help reduce signal attenuation and channel-dependent errors. The normally open configuration allows each channel to remain disconnected until its corresponding control signal activates the selected path. Each switch operates independently, enabling four separately controlled routes within one package. The MAX352 is differentiated from the MAX351 by its normally open switches, while the MAX353 combines two normally open and two normally closed channels. Switching times of 175ns and 145ns are listed for the device, supporting fast control-loop and communication-interface operation. Typical uses include precision signal selection, sample-and-hold systems, multiplexed test paths, digital signal processing front ends, and communication equipment. The low 250pA off leakage is particularly useful when switching high-impedance sources, where unwanted leakage could create measurement errors or disturb sensitive analog nodes. The 16-pin PDIP package also supports straightforward through-hole assembly and prototyping. Designers should verify signal amplitude, control-logic levels, maximum current, and operating temperature against the manufacturer datasheet. Keep sensitive analog traces short, provide a stable ground reference, and avoid exceeding the switch's 15V signal or supply range. The normally open topology requires deliberate control sequencing if a default isolation state is required. This product page consolidates the MAX352 family specifications, verified source links, package information, application guidance, and compatible alternatives into an engineering-focused reference for analog signal-routing designs.

RFQ যোগাযোগ
MAX352EPE - Quad 35Ω SPST Analog Switch | Maxim Integrated
MAX352EPE

MAX352EPE - Quad 35Ω SPST Analog Switch | Maxim Integrated

The Maxim Integrated MAX352EPE is a precision quad SPST analog switch with four normally open channels, a 35Ω on-resistance, and a 16-pin PDIP package. It is designed for controlled routing of low-frequency analog signals and provides a 1:1 circuit configuration. An analog switch is an integrated semiconductor device that connects or disconnects signal paths under digital control. The MAX352 belongs to the broader hierarchy of analog switches, analog multiplexers, interface ICs, and semiconductor signal-routing components. Unlike a mechanical relay, it changes connection state electronically, allowing compact equipment with fast and repeatable routing. Each of its four switches is normally open, so the default state provides signal-path isolation rather than a permanently connected route. Key characteristics include four SPST channels, 1:1 signal routing, and a maximum specified on-resistance of 35Ω. The EPE suffix identifies the 16-pin PDIP industrial-temperature ordering variant. The device is supplied as a through-hole package, making it appropriate for legacy boards, instrumentation, control systems, and prototypes where a surface-mount footprint would be inconvenient. The product family is produced by Maxim Integrated, whose product portfolio is now represented by Analog Devices. The MAX352’s four normally open switches make it useful for source selection, signal isolation, test-point routing, and external-interface switching. Each channel can independently connect its designated terminal pair when the corresponding control input is asserted. Because it is a unilateral 1:1 routing element, the switch should be evaluated for signal amplitude, source impedance, leakage, charge injection, and off-state behavior according to the manufacturer data sheet. The MAX352 is especially relevant when rebuilding or maintaining equipment that already specifies a 16-pin quad-SPST analog switch. Because pin compatibility and electrical equivalence must be confirmed at the exact terminal and control level, engineers should compare the full data sheet rather than relying only on the package outline. The 35Ω resistance can be significant for high-impedance precision measurements, while it may remain acceptable for control, sensor, audio, or low-frequency instrumentation signals. A practical layout should route sensitive analog conductors away from digital control traces, maintain a common ground reference, and place protection or filtering components where they do not degrade switch isolation. The MAX352EPE is also the exact 16-pin PDIP member to select when a MAX352 function is required and the board does not provide SMD pads. This page combines the manufacturer family information with verified distributor packaging details, replacement analysis, application guidance, and design considerations for engineers maintaining or reproducing a MAX352EPE-based circuit.

RFQ যোগাযোগ
MAX353EPE+ - Quad SPST 35Ω Analog Switch | Analog Devices
MAX353EPE+

MAX353EPE+ - Quad SPST 35Ω Analog Switch | Analog Devices

The Analog Devices MAX353EPE+ is a precision, quad, single-pole single-throw analog switch in a 16-pin PDIP package. It provides four 1:1 switch channels, a maximum on-resistance specification of 35Ω, on-resistance matching within 2Ω between channels, and on-resistance variation of no more than 3Ω across the analog signal range. The circuit combines two normally open and two normally closed switches in one device. An analog switch is a semiconductor-controlled connectivity component that routes analog signals between circuit nodes. A single-pole single-throw, or SPST, switch makes or breaks one signal path rather than selecting among multiple inputs. As an integrated analog switch IC, the MAX353EPE+ provides four independent switch functions in one package, reducing component count and simplifying routing in precision signal-path systems. The principal benefit is repeatable low on-resistance with close matching between channels. The manufacturer specifies on resistance below 35Ω, channel-to-channel matching within 2Ω, and flatness of less than 3Ω over the analog signal range. These characteristics help minimize gain errors, resistance-induced distortion, and channel-dependent offsets when signals pass through the selected switch. The MAX353EPE+ belongs to the MAX351, MAX352, and MAX353 precision quad-SPST family. The MAX351 uses four normally closed switches, the MAX352 uses four normally open switches, and the MAX353 divides its four channels into two normally open and two normally closed configurations. This makes the MAX353 useful where both resting-connect and resting-disconnect behavior are required within one package. Typical uses include precision measurement systems, signal-routing networks, test and measurement equipment, data-acquisition interfaces, and industrial control electronics. The mixed normally open and normally closed arrangement is especially useful for signal isolation, controlled paths to common test points, or systems that need different default connection states for different measurement channels. PCB design should preserve the manufacturer's recommended pin assignments and provide a continuous ground return around the switching circuitry. Because the device is a through-hole PDIP package, place it close to the source and destination signal traces when practical. Review the pin-description table in the Analog Devices datasheet before assigning control inputs, supply connections, and switch terminals. This page combines the manufacturer's device description with practical packaging guidance, application analysis, and a qualification-focused comparison against other MAX353 members. It also distinguishes true same-footprint choices from related devices that use different packages or switch configurations, helping engineers avoid substitutions that change default signal states.

RFQ যোগাযোগ
MAX354CPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX354CPE+

MAX354CPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX354CPE+ is a single 8:1 fault-protected analog multiplexer with 350 ohm on-resistance, packaged in a 16-pin PDIP. It routes one of eight analog inputs to a common output and provides protection against overvoltage up to 40 V beyond the supply rails during power-up, power-down, and fault conditions. The series N-channel, P-channel, N-channel switch architecture is designed to protect sensitive downstream circuitry when an input temporarily exceeds the normal supply range. An analog multiplexer is a switching IC that connects multiple signal sources to one shared signal path. The MAX354 belongs to the broader analog switch and multiplexer hierarchy, where fault-protected muxes are used to isolate external inputs from sensitive measurement, control, and communication circuits. Its 8:1 configuration makes it appropriate when a system must select among eight sensors, instrument channels, voltage sources, or other low-frequency analog signals. The key operating attributes are its 8:1 single-channel architecture, 350 ohm on-resistance, 16-pin PDIP package, and fault protection to 40 V beyond the supply rails. These characteristics make the device especially useful in industrial and instrumentation systems where input signals can exceed the normal operating voltage during startup or abnormal system conditions. The MAX354 family is identified as production by Analog Devices, supporting continued design use for new equipment. Internally, the MAX354 uses a series N-channel, P-channel, N-channel structure. The protected switching path limits fault exposure while retaining the basic function of an analog multiplexer. Because this is a passive analog switching function rather than a powered conversion stage, designers should focus on signal range, on-resistance, leakage, switching behavior, supply requirements, and input protection when evaluating system performance. Typical applications include industrial sensor acquisition, automated test equipment, data acquisition, process-control interfaces, battery and power-system monitoring, and communication equipment. In these systems, the common output can feed an amplifier, converter, or controller while the multiplexer protects that downstream component from excessive input voltage. PCB design should preserve the pin assignments and signal-path geometry defined by the manufacturer datasheet. Keep the selected channel traces short, maintain a common ground reference between the multiplexer and analog front end, and account for the 350 ohm on-resistance when calculating source impedance, signal attenuation, and input-referred noise. Confirm all operating voltages and fault conditions before using the protected inputs near the stated 40 V beyond-rail limit.

RFQ যোগাযোগ
MAX354CWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX354CWE+

MAX354CWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX354CWE+ is a single 8:1 fault-protected analog multiplexer with 350 ohm on-resistance, housed in a 16-pin SOIC package. It uses a series N-channel, P-channel, N-channel protection structure to withstand voltages up to 40 V beyond the supply rails during power-up, power-down, and fault conditions. This makes the device suitable for routing external analog signals into circuitry that requires protection from transient or fault-induced overvoltage. An analog multiplexer is an interface IC that connects one common signal path to multiple input channels through controlled switches. Within the product hierarchy, the MAX354 is a fault-protected analog switch, then an analog multiplexer, then an interface IC used in broader signal-routing and power-management systems. Unlike a mechanical relay, it provides compact electronic channel selection, while its internal protection structure adds resilience beyond that of an unprotected CMOS multiplexer. The MAX354 family combines an 8:1 multiplexing arrangement with an on-resistance of 350 ohm. Its fault-protection architecture is designed to protect downstream circuitry when an input can be driven above or below the normal supply range. The MAX354 is the single-channel version in a family that also includes the MAX355, which is a dual 4:1 fault-protected analog multiplexer. This distinction is important when selecting between single-ended eight-way routing and two independent four-way muxes. The MAX354 is intended for analog instrumentation, test and measurement systems, data acquisition modules, industrial control interfaces, and other applications where a protected input must be connected to downstream signal-processing circuitry. Its 16-pin SOIC package supports conventional surface-mount assembly and provides enough pins for the common connection, eight mux inputs, control logic, supply rails, and fault-protection elements. Use the manufacturer pin-description table to assign PCB nets and verify the exposed electrical characteristics before production release. A critical design consideration is the relationship between external signal amplitude and the device supply range. The protection structure is intended to tolerate overvoltage beyond the rails, but it does not eliminate the need to review absolute maximum ratings, input-current limits, channel leakage, and operating conditions. Designers should also account for the 350 ohm on-resistance when calculating source impedance, attenuation, bandwidth, and downstream amplifier loading. This page combines the manufacturer’s fault-protection description with distributor package information, replacement analysis, and practical PCB guidance. It distinguishes verified device facts from parameters that require confirmation in the manufacturer datasheet, helping engineers plan footprint, sourcing, and signal-path design before schematic release.

RFQ যোগাযোগ
MAX354EWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX354EWE+

MAX354EWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX354EWE+ is a single 8:1 analog multiplexer with a 350 ohm on-resistance, fault protection to 40 V beyond the supply rails, and a 16-pin SOIC package. It routes one of eight single-ended analog inputs to a common output while protecting sensitive downstream circuitry during power-up, power-down, and fault conditions. An analog multiplexer is an interface IC that connects multiple signal paths to a shared processing or measurement resource. The MAX354 belongs to the broader switch and multiplexer hierarchy, where multiplexing reduces the number of input channels, converters, amplifiers, or external connectors required by an electronic system. Its fault-protected architecture is especially useful when external signals can exceed the nominal supply range during startup or abnormal operating conditions. The MAX354EWE+ provides eight channels, a 350 ohm on-resistance, and protection against overvoltage up to 40 V beyond the supply rails. These characteristics make the device relevant to data acquisition, instrumentation, test systems, industrial control, and battery-powered equipment. The MAX354/MAX355 family uses a series N-channel, P-channel, N-channel structure that isolates protected downstream components from excessive input voltage. The device is specified as a single-ended multiplexer in a 16-SOIC surface-mount package. Its industrial temperature grade suits equipment expected to operate across demanding environmental conditions. Because on-resistance and protection behavior influence signal fidelity and system reliability, designers should account for the complete source impedance, selected channel, supply state, and external signal amplitude rather than treating the switch as an ideal conductor. Typical uses include eight-channel sensor selection, industrial measurement front ends, automated test equipment, and embedded control systems that need to share an analog-to-digital converter or signal-conditioning channel. In these systems, the multiplexer reduces channel count while the fault-protected structure provides additional tolerance for externally driven signals. The final input range must remain compatible with the complete signal chain and device operating limits. A key design consideration is the relationship between the multiplexer, the protected signal source, and downstream circuitry. Keep sensitive return paths compact, observe the manufacturer’s pin configuration when assigning inputs and enables, and evaluate the switch resistance in the source impedance of the selected channel. The 350 ohm on-resistance is especially important for high-impedance sensors and low-amplitude measurements. This product page combines the manufacturer’s multiplex function, protection characteristics, package details, application analysis, and parameter-level comparison. It also distinguishes device-family options from true pin-compatible drop-in replacements so that PCB changes are not mistaken for a straightforward substitution.

RFQ যোগাযোগ
MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim
MAX355CWE+

MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim

The Maxim Integrated MAX355CWE+ is a dual 4:1 fault-protected analog multiplexer with two independently controlled 4:1 switches, 350 ohm on-resistance, and a 16-pin WSOIC package. Its 4.5 V to 36 V operating supply range and protection against overvoltage up to 40 V beyond the supply rails make it suitable for routing signals through systems where input pins may temporarily exceed the normal supply limits during power-up, power-down, or fault conditions. An analog multiplexer is a switching interface that connects one signal source to one of several destinations. In this case, each MAX355CWE+ channel implements a 4:1 configuration, allowing two multiplexers to route four sources per channel. Within the broader semiconductor hierarchy, the MAX355CWE+ is an analog switch IC, then a multiplexer, then an interface IC used to connect external signals to analog processing circuitry. Key electrical characteristics include a maximum on-resistance of 350 ohms, maximum off leakage of 500 pA, and crosstalk of -92 dB at 100 kHz. The 350 ohm resistance is suitable for moderate-impedance sensor, measurement, and control paths rather than high-bandwidth, low-impedance video networks. Fault protection extends to 40 V beyond the supply rails, helping isolate sensitive downstream circuitry during abnormal input conditions. The device uses a series N-channel, P-channel, and N-channel switching structure to provide fault protection. Its dual-mux architecture makes it useful where multiple analog inputs must be selected under software or hardware control. Control inputs allow the selected paths to be changed without mechanical switching, making the MAX355CWE+ appropriate for test systems, industrial controls, data acquisition modules, and instrumentation. Typical uses include battery-powered monitoring equipment, industrial sensor interfaces, laboratory measurement systems, and analog test equipment. The 4.5 V minimum supply supports systems operating from a 5 V rail, while the 36 V maximum expands applicability to higher-voltage industrial environments. Protection is especially relevant where an external cable or sensor may present an overvoltage before system power stabilizes. Designers should verify the input and output voltage limits against the specific fault condition and avoid treating the 40 V protection rating as a continuous operating rating. Keep analog routing paths away from high-current switching nodes, provide a stable bypass capacitor near the supply pins, and use high-impedance sensing circuits to reduce errors caused by the 350 ohm on-resistance. This page combines the MAX355CWE+ electrical characteristics, application guidance, package information, and verified drop-in alternatives to support faster component selection and PCB replacement decisions.

RFQ যোগাযোগ
MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim
MAX355EWE+

MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim

The Maxim Integrated MAX355EWE+ is a dual 4:1 analog multiplexer with two independent SP4T switching circuits, a 350 ohm on-resistance, and fault protection to 40 V beyond the supply rails. It operates from 4.5 V to 36 V and is packaged in a 16-pin wide SOIC configuration for surface-mount industrial electronics. An analog multiplexer routes one of several analog inputs to an output according to digital select-control signals. The MAX355 family belongs to the analog-switch and multiplexer hierarchy, where switch resistance, channel isolation, logic levels, supply range, and fault tolerance determine whether a device is suitable for precision measurement, test equipment, battery systems, or signal-routing networks. The MAX355EWE+ combines two 4:1 muxes in one 16-pin package. Its principal electrical characteristics include 2 circuits, 8 selectable channels, 350 ohm on-resistance, and a 4.5 V to 36 V operating supply range. The series N-channel, P-channel, N-channel switch architecture is designed to limit fault current and protect downstream circuitry during power-up, power-down, and overvoltage conditions. Fault protection extends as much as 40 V beyond the positive and negative supply rails. This characteristic is important when an external signal may exceed the local supply range during startup or an electrical fault. The protection structure is intended to preserve sensitive measurement circuits rather than serve as a substitute for normal operating-voltage design or external surge protection. Typical uses include battery-powered instrumentation, programmable test and measurement systems, industrial sensor acquisition, analog signal routing, and communication equipment that must select among several analog inputs. The wide 4.5 V to 36 V supply span supports both low-voltage portable systems and higher-voltage industrial signal chains. PCB design should reserve the complete 16-pin footprint exactly as defined by the manufacturer pin description and place bypass capacitors close to the supply pins. Before substituting the device into an existing board, verify control-logic thresholds, input signal range, switch timing, and the specific operating-temperature grade. This page combines the manufacturer product information with practical fault-protection guidance, same-footprint alternatives, sourcing instructions, and design considerations for engineers evaluating the MAX355EWE+ as a protected dual analog multiplexer.

RFQ যোগাযোগ
MAX358CWE+ - Fault-Protected 8:1 Analog Multiplexer | ADI
MAX358CWE+

MAX358CWE+ - Fault-Protected 8:1 Analog Multiplexer | ADI

Analog Devices MAX358CWE+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 1.8 kOhm on-resistance and approximately 1 MHz bandwidth in a 16-pin SOIC package. According to the manufacturer product page, the MAX358 family is designed for multiplexers and demultiplexers that must withstand fault conditions beyond their normal supply rails. An analog multiplexer is an interface IC that routes one of several input channels to a shared output or measurement path. The MAX358 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs and semiconductors. By selecting among eight single-ended inputs with controlled switches, it reduces the number of signal lines required between sensors, test points, data-conversion systems and other analog circuits. The MAX358 family combines an 8:1 configuration with 1.8 kOhm on-resistance and approximately 1 MHz bandwidth. Its listed operating supply range is 4.5 V to 18 V, while the fault-protection architecture provides protection for overvoltage conditions extending to ±35 V beyond the supply rails when power is removed. The manufacturer describes the implementation as a series N-channel, P-channel, N-channel structure. MAX358 is the single-ended member of a related fault-protected multiplexer family. The MAX359 provides a four-channel differential configuration, while the MAX358 is intended for eight-channel single-ended routing. The device uses address and control inputs to select the active path and supports analog signal multiplexing in systems where input faults, limited board area and modest bandwidth are more important than very low on-resistance. Typical uses include data acquisition, instrumentation, test and measurement, industrial control, battery monitoring and embedded analog signal routing. The 1 MHz bandwidth is suitable for many sensor and control signals, while the fault-protection feature helps isolate downstream circuitry from excessive input voltage. System designers should still validate signal levels, transition behavior and protection conditions against the manufacturer datasheet. PCB implementation requires careful routing of the selected analog path and control signals to prevent interference between channels. Place the multiplexer close to the source or destination of the routed signal, maintain a continuous ground reference, and follow the datasheet layout guidance for bypass capacitors and exposed routing areas. This product page combines the manufacturer specifications with practical design guidance, package information, sourcing workflow and verified drop-in alternatives. It is intended to help engineers determine whether the MAX358CWE+ fits an analog routing design before detailed circuit simulation and board validation.

RFQ যোগাযোগ
MAX358EPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX358EPE+

MAX358EPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX358EPE+ is a fault-protected, single-ended 8:1 analog multiplexer with 1.8 kOhm on-resistance in a 16-pin PDIP package. It routes one of eight input channels to a common output while providing fault protection, power-off isolation, and an operating temperature range of -40°C to +85°C. The device is intended for systems where an input may experience voltage excursions beyond the normal supply rails. An analog multiplexer is an interface IC that connects multiple signal sources to one processing channel. The MAX358 family uses this switching architecture to reduce the number of converters, sensor inputs, or control lines required by a measurement system. In the hierarchy of semiconductor devices, it is an analog switch IC, an interface IC, and ultimately a discrete analog function rather than a digital logic component. The MAX358EPE+ provides eight single-ended channels, 1.8 kOhm on-resistance, and fault protection covering ±35 V beyond the supply rails. Power-off isolation prevents connected sources from being significantly influenced when the device is unpowered. These characteristics make the multiplexer useful for data acquisition, industrial control, test equipment, and instrumentation where signal routing and input protection must coexist in a compact package. The 16-pin PDIP construction supports through-hole assembly and straightforward inspection or rework on suitable boards. The MAX358 family is identified by Analog Devices as a production product. Circuit designers should still verify signal amplitude, supply voltage, leakage, switching timing, and channel capacitance against their exact system requirements before finalizing the PCB and input-protection network. Typical uses include multiplexed sensor acquisition, programmable instrumentation, industrial control interfaces, automated test equipment, and data-logging modules. In these applications, the common output can be connected to an ADC or measurement front end while the address and enable controls select the required channel. Care is required when switching high-impedance sources because off leakage, charge injection, and settling time influence measurement accuracy. A practical design priority is to preserve the mux's fault-protection capability rather than placing unrestricted external voltages directly on every input. Confirm the absolute maximum conditions and ensure that control logic, supply sequencing, and external clamping are compatible with the selected operating state. This page also consolidates practical selection guidance, verified alternatives, and design considerations for engineers evaluating the MAX358EPE+.

RFQ যোগাযোগ
MAX359EPE - Fault-Protected 4:1 Analog Multiplexer | Maxim
MAX359EPE

MAX359EPE - Fault-Protected 4:1 Analog Multiplexer | Maxim

The Maxim Integrated MAX359EPE is a fault-protected dual 4:1 analog multiplexer packaged in a 16-pin PDIP. It uses a series N-channel, P-channel, N-channel switch structure to improve protection when the device is powered while its input or output pins exceed the supply rails. The circuit can select one of four differential signal pairs for connection to two common outputs, making it useful for controlled analog-routing and measurement systems. An analog multiplexer is an interface IC that routes multiple analog inputs through a shared output path under digital control. A 4:1 multiplexer reduces the number of signal lines required when several sources must be measured sequentially. The MAX359 extends this function with fault-protection circuitry intended to limit damage caused by overvoltage conditions. In the system hierarchy, it belongs to analog switches and multiplexers, interface ICs, and the broader semiconductor category. The MAX359 family provides two independently selectable 4:1 configurations, giving 8 differential input channels in total. According to the MAX359 manufacturer product page, the MAX359 is the four-channel differential, 2-of-8 multiplexer, while the MAX358 is an eight-channel single-ended 1-of-8 device. Its specified on resistance is 1.8 kOhm. The MAX359EPE is identified as an industrial-temperature component, and the E suffix denotes the manufacturer ordering variant shown in the product records. The internal series N-channel, P-channel, N-channel arrangement is specifically intended to improve fault protection compared with simpler multiplexer implementations. This architecture matters when analog inputs can temporarily exceed the supply voltages. The active device still has defined supply limits, and the manufacturer should be consulted before applying voltages beyond its absolute maximum ratings or using the multiplexer as a substitute for dedicated protection components. Typical uses include multichannel instrumentation, sensor acquisition, battery and power-system monitoring, industrial control, and laboratory test equipment. Differential routing is particularly useful for rejecting common-mode disturbance when paired signals share similar noise characteristics. The two 4:1 sections can also support redundant or comparative measurements when the system must route more than one signal group to shared processing circuitry. For PCB design, place the device so that muxed analog traces remain short and are surrounded by a stable ground reference. Keep external switching or protection components close to exposed connector pins, and route digital select inputs away from sensitive analog inputs to reduce crosstalk. Before power-up, verify every control and signal pin against the manufacturer's operating limits. The family datasheet and pin-description table should define the correct pin assignments and supply requirements. This page combines the manufacturer function description, package and routing characteristics, practical design guidance, sourcing questions, and qualified drop-in alternatives. It also separates exact ordering variants from package changes, helping engineers identify whether a proposed replacement preserves the original 16-pin PDIP footprint and electrical behavior.

RFQ যোগাযোগ
MAX361CSE+ - Quad SPST Analog Switch | Analog Devices
MAX361CSE+

MAX361CSE+ - Quad SPST Analog Switch | Analog Devices

Analog Devices MAX361CSE+ is a precision, quad, single-pole single-throw analog switch with four normally closed switches, packaged in a 16-pin SOIC. The device provides low channel on resistance of less than 85 ohms, with on-resistance matching maintained within 3 ohms between channels. Its on resistance remains flat across the analog signal range, with a maximum change of 9 ohms. The MAX361CSE+ is designed for precision signal-routing systems where repeatable resistance, low leakage, and consistent channel behavior are important. An analog switch is a semiconductor device that routes analog signals between terminals under digital control. The MAX361CSE+ belongs to the analog switch and multiplexer hierarchy, where a multiplexer combines switching functions with signal selection. Its four normally closed SPST channels default to the connected state when the control input is inactive. This architecture is useful in test systems, measurement instruments, audio paths, sensor interfaces, and communication equipment that require controlled switching of low-voltage signals. The primary benefit of the MAX361CSE+ is channel-to-channel consistency. According to the Analog Devices MAX361 product page, the device guarantees less than 85 ohms of on resistance and matching within 3 ohms among channels. The on-resistance characteristic changes by no more than 9 ohms across the supported analog signal range. These specifications reduce gain error and channel-to-channel variation when the same source resistance, amplifier gain, or measurement calibration is used across multiple switched paths. The MAX361CSE+ contains four independent precision SPST switches, allowing a system to connect or isolate several signal lines without changing the PCB footprint. Its 16-pin narrow SOIC package supports conventional surface-mount assembly and keeps the routing distance between external circuitry and the switch short. The manufacturer identifies the MAX361 family as being in production and lists the MAX361 data sheet as Revision 2. Typical uses include front-end signal selection, instrumentation amplifiers, automated test equipment, data acquisition systems, and audio routing networks. Because the switches are normally closed, they can also preserve signal continuity during control-signal transitions or provide a default connection when an external controller is unavailable. Designers should still account for injected power, off-state isolation, control logic levels, and signal amplitude when constructing the surrounding analog circuit. Layout and signal integrity require attention around high-impedance analog paths. Keep input and output traces short, use a continuous ground reference, and avoid routing sensitive signals next to clocked or switching circuitry. Verify the control levels and operating conditions in the MAX361 data sheet before relying on a default state during power-up. Decoupling and protection components should be selected from the actual signal bandwidth, source impedance, and external voltage limits. This product page combines the MAX361CSE+ technical description with package information, application guidance, design notes, and a focused comparison against identified same-package alternatives. It is intended to help engineers distinguish the normally closed MAX361 from other switching functions and to plan PCB, sourcing, and signal-path decisions around the verified 16-pin SOIC implementation.

RFQ যোগাযোগ
MAX361ESE+ - 85 Ohm Quad SPST Analog Switch | Maxim Integrated
MAX361ESE+

MAX361ESE+ - 85 Ohm Quad SPST Analog Switch | Maxim Integrated

The Maxim Integrated MAX361ESE+ is a precision quad SPST analog switch with four normally closed channels, 85 ohm on resistance, and a 16-SOIC package. The device is designed for precision signal routing applications where four independent channels must switch between analog signals. Its 1:1 configuration, matched on-resistance behavior, and low-leakage design make it suitable for instrumentation, test systems, and signal-chain control. An analog switch is an integrated semiconductor device that routes signals between circuit nodes under digital control. The MAX361ESE+ belongs to the analog switch and multiplexer category, where its normally closed SPST architecture connects each input to its corresponding output when the control state is inactive. The four channels provide convenient parallel routing without requiring four separate discrete switch packages. The main electrical feature of the MAX361ESE+ is its maximum channel on resistance of 85 ohms. Maxim specifies that channel resistance is guaranteed to match within 3 ohms between channels and remain flat over the analog signal range, with a maximum variation of 9 ohms. This matching behavior is important in precision systems because unequal channel resistance can create gain errors, distortion, or inconsistent attenuation when different channels are selected. The MAX361ESE+ is a single-pole single-throw device with four normally closed switches. Its control interface supports external digital control of the four signal paths, allowing an instrument, measurement system, or controller to select a signal route while minimizing external discrete components. The device is also specified for low leakage, which helps preserve the integrity of high-impedance measurement nodes when switches are open. Typical applications include precision instrumentation, automated test equipment, multiplexed sensor interfaces, signal patching, sample-and-hold systems, and laboratory measurement setups. In these systems, the four matched channels can route several sensor or reference signals into a common measurement chain while reducing insertion-resistance variation between channels. The principal design consideration is signal integrity. Traces connected to the analog pins should be kept short, and the switch should be placed close to the source and destination circuitry when possible. Power-supply bypassing and grounding are important in high-impedance systems because parasitic capacitance and leakage can degrade the measured signal even when the nominal on-resistance is well controlled. This page combines the manufacturer product information, verified distributor listings, package details, comparison data, and practical routing guidance for engineers evaluating the MAX361ESE+ in precision analog-switch designs.

RFQ যোগাযোগ
MAX362CPE+ - Quad SPST NO Analog Switch | Analog Devices
MAX362CPE+

MAX362CPE+ - Quad SPST NO Analog Switch | Analog Devices

The Analog Devices MAX362CPE+ is a precision quad single-pole single-throw analog switch with four normally open channels, less than 85 ohms on-resistance, and a 16-pin PDIP package. It provides a 1:1 signal-routing architecture for analog and digital test systems, measurement equipment, instrumentation, and signal isolation applications. Each of the four independent switches connects one external signal terminal to one common signal terminal when its control input is asserted. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX362 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs, and signal-management semiconductors. Unlike a mechanical relay, it offers faster electronic control, while its precision on-resistance and channel matching help reduce signal degradation when multiple channels are switched. The MAX362CPE+ features a maximum specified on-resistance below 85 ohms. According to the Analog Devices MAX362 product information, on-resistance can match within 2 ohms between channels and remain flat with a maximum variation of 9 ohms over the analog signal range. These characteristics are important where channel-to-channel gain variation, insertion loss, or switching consistency affects measurement accuracy. The device uses four normally open switches, so each channel is disconnected until its corresponding control input is driven active. Technical differentiation comes from the combination of four independent channels in one package, low channel on-resistance, close channel matching, and flat resistance behavior. These characteristics make the MAX362 useful when a system needs repeatable analog multiplexing without the larger footprint or higher control complexity of a multi-channel relay matrix. The 16-pin PDIP package is also appropriate for through-hole assembly, prototype boards, test fixtures, and legacy industrial equipment. Typical uses include multimeter and oscilloscope input routing, automated test equipment, signal routing in data-acquisition systems, sample-and-hold circuitry, and analog measurement front ends. Each switch can route one of four external nodes to a shared destination, allowing a compact controller to select among multiple sensors or sources. Because the MAX362 is normally open, it also supports isolation-style routing where an inactive channel presents an open path. PCB design should keep each switched signal trace short and place the device close to the signal source or shared destination. Long traces can add parasitic capacitance and inductance, especially when signals change rapidly between the open and closed states. Confirm control-logic levels, supply requirements, allowable input voltage range, and absolute maximum ratings in the manufacturer datasheet before finalizing the interface circuit. This product page combines the manufacturer function description, package and switching characteristics, lifecycle information, sourcing guidance, and application-focused design guidance. It also distinguishes verified drop-in alternatives from functionally related but mechanically or electrically unsuitable parts, helping engineers shorten component-selection and PCB-validation work.

RFQ যোগাযোগ
MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices
MAX362CSE+

MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices

The Analog Devices MAX362CSE+ is a precision quad, single-pole single-throw analog switch with four normally open switches, packaged in a 16-pin SOIC. The device provides a 1:1 signal configuration and an on resistance of 85 ohms, making it suitable for routing precision analog signals in test, measurement, instrumentation, and communication equipment. An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw, or SPST, switch contains one signal path that is either connected or disconnected. The MAX362 uses four normally open channels, so each channel is off during its inactive state and connects the selected signal when the corresponding control input is asserted. This topology is useful when a system must route one source to one destination without connecting the active path permanently. The MAX362 family is designed for precision signal handling. According to the Analog Devices MAX362 product page, the on resistance is less than 85 ohms, channel-to-channel matching is guaranteed within 3 ohms, and resistance variation across the analog signal range is limited to a maximum change of 9 ohms. These characteristics support predictable signal attenuation when the same switch is used with different channels or operating signal levels. The MAX362CSE+ provides four independently controlled switch channels in a 16-SOIC package. The MAX362 product family is also available in complementary normally closed form as the MAX361, allowing complementary routing behavior to be considered when designing control logic. The MAX362CSE+ ordering suffix denotes the leaded SOIC package configuration identified in the product listing. Typical applications include precision signal routing, bench-test equipment, data-acquisition systems, communication-channel selection, and analog measurement paths. Because the switch resistance and matching characteristics are central to its performance, system-level calculations should include the effective source and load impedances, expected signal amplitude, settling behavior, and the contribution of switch on resistance. When laying out a board around the MAX362CSE+, keep analog input and output traces short and connect the device ground pins to a low-impedance ground plane. Place nearby bypassing capacitors at the supply entry point and keep digital control traces away from sensitive analog paths. Review the manufacturer datasheet for the exact pin assignments, absolute maximum ratings, recommended operating conditions, and electrical characteristics before releasing the layout. This product page combines the manufacturer family description, package identification, sourcing information, practical layout guidance, and a structured comparison framework to support component selection and PCB design. It also distinguishes verified product facts from parameters that require confirmation in the MAX362 datasheet.

RFQ যোগাযোগ
MAX362EPE - 4-Channel 85Ω SPST Analog Switch | Maxim
MAX362EPE

MAX362EPE - 4-Channel 85Ω SPST Analog Switch | Maxim

Maxim MAX362EPE is a precision quad-channel, single-pole single-throw analog switch with four normally open circuits, an 85 Ω on resistance, and a 16-pin PDIP package. The device provides 1:1 signal routing for four independent analog channels and is packaged for through-hole PCB assembly rather than surface mounting. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST architecture provides one selectable path for each circuit, while the quad configuration integrates four independent switches into one package. Within the signal-path hierarchy, MAX362EPE belongs to the analog switch and multiplexing category, where low on resistance, predictable channel behavior, and control-signal compatibility are central design considerations. The MAX362EPE differentiates itself through its four normally open switch functions and listed 85 Ω on resistance. Its 1:1 configuration preserves signal polarity rather than inverting the selected path. The device is listed in an industrial temperature grade and uses a rectangular PDIP-16 package. Four independent control inputs allow a microcontroller or logic circuit to route separate analog nodes without requiring a separate single-channel package for each function. The MAX361 and MAX362 share the same precision quad-SPST family, but their default contact states differ. MAX362 uses normally open switches, which leave each channel disconnected until the corresponding control signal asserts the connection. This behavior is useful when signal isolation during reset or power-up is required. Exact voltage ratings, leakage currents, channel-to-channel resistance matching, switching-time limits, and absolute maximum conditions should be confirmed in the manufacturer datasheet before a new design is released. Typical uses include multiplexed sensor acquisition, instrumentation signal routing, test-equipment input selection, industrial control interfaces, and precision analog measurement systems. In these applications, the four switch channels can reduce the number of discrete relays or routing components while allowing software-controlled path selection. Engineers must still check the signal amplitude, bandwidth, leakage, and control-logic thresholds against the complete operating specification. A practical design consideration is to route each analog trace away from fast digital or switching-regulator nodes, and to place any protection or filtering components close to the connector or source. Because the MAX362EPE uses normally open contacts, system startup and fault-response logic should account for the unasserted state. Confirm the complete pin mapping and control polarity against the manufacturer datasheet before laying out a board. This product page consolidates the exact MPN identity, package information, lifecycle information, commercial ordering path, and available drop-in comparison for the obsolete MAX362EPE. It also adds practical guidance on analog-signal integrity, default switch state, control sequencing, and the checks required when replacing legacy through-hole analog switches.

RFQ যোগাযোগ
MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices
MAX362ESE+

MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices

Analog Devices MAX362ESE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 85Ω, and a 16-pin SOIC package. The switch is designed for controlled routing of low-frequency analog signals where consistent channel resistance, low leakage, and a compact surface-mount footprint are important. An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw switch provides one signal path that is normally disconnected and closes when its control input is asserted. The quad architecture gives the MAX362ESE+ four independent switch paths, reducing component count in test systems, measurement instruments, signal-conditioning circuits, and controlled analog-routing designs. The MAX362 family provides on-resistance below 85Ω across the analog signal range. Analog Devices specifies channel matching within 3Ω and a maximum on-resistance change of 9Ω, helping preserve amplitude relationships when signals pass through multiple channels. These characteristics are especially useful when attenuation, calibration, or measurement accuracy depends on similar resistance among switched paths. The MAX362ESE+ differs from the MAX361 family member through its normally open switch configuration: MAX362 uses normally open channels, while MAX361 uses normally closed channels. Its 1:1 circuit arrangement means the device does not inherently invert the signal. The industrial temperature-grade designation and 16-lead SOIC packaging support conventional surface-mount assembly for industrial and instrumentation applications. Typical uses include low-frequency sensor multiplexing, sample-and-hold signal routing, automated test equipment, programmable gain networks, and laboratory measurement interfaces. The four channels can route related nodes to a common analog processing chain, although system timing and control logic must ensure that only the intended channel is closed when signal integrity matters. Layout should keep analog traces short and place bypass and interface components near their associated pins. Control signals should transition cleanly, and unused control or signal pins should be connected according to the manufacturer pin-description table. Because switch resistance can vary with signal amplitude, verify the complete signal path and account for Ron when designing precision dividers, current loops, or low-amplitude sensor interfaces. This page consolidates the manufacturer switch characteristics, package information, sourcing workflow, verified replacement reference, and practical implementation guidance. It is designed to help engineers evaluate the MAX362ESE+ for new analog-routing designs and assess PCB reuse without relying on generic analog-switch descriptions.

RFQ যোগাযোগ
MAX364ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices
MAX364ESE+

MAX364ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices

Analog Devices MAX364ESE+ is a precision, quad, single-pole single-throw analog switch with four normally closed channels, a maximum on-resistance of 85Ω, and a 16-pin narrow SOIC package. The device supports 1:1 signal routing and is designed for precision analog systems where channel resistance matching, low leakage, and consistent off-state isolation are important. An analog switch is an electronic routing component that connects or disconnects analog signals under digital control. A SPST switch provides one conducting path, while the MAX364's normally closed configuration connects each signal path when its control input is inactive. Within the broader semiconductor hierarchy, this device is an analog switch, then a switch IC and interface IC. It is intended to bridge low-frequency or precision analog signals without using a mechanical relay. The MAX364 provides four independent normally closed channels, low on-resistance below 85Ω, on-resistance matching within 2Ω between channels, and on-resistance variation of no more than 9Ω across the analog signal range. These characteristics help limit insertion-error differences between channels. The equalized resistance also supports reproducible measurements when several switched nodes participate in the same precision measurement path. Each MAX364/MAX365 family member uses the same precision switch architecture, but the MAX364 has four normally closed switches while the MAX365 has four normally open switches. The MAX364ESE+ suffix identifies the narrow 16-SOIC configuration. Its four control inputs allow independent routing of four analog nodes, making it practical for scanning, signal isolation, sample-and-hold interfaces, and programmable test systems. Typical applications include precision multimeter input switching, automated test equipment, data-acquisition systems, instrumentation signal routing, and analog measurement front ends. In each case, the normally closed state can preserve signal continuity during reset or control-signal absence. The matched low on-resistance also reduces channel-dependent errors when the same source drives different measurement paths. For layout, route high-impedance signals directly to the switch pins and keep the analog traces short and away from fast digital or switching nodes. Check the control-logic levels and supply conditions in the manufacturer datasheet before designing the driver. Treat the 85Ω on-resistance as part of the complete source impedance rather than as an isolated component value, because series source resistance and switch resistance combine to determine signal attenuation.

RFQ যোগাযোগ