উপশ্রেণী

পণ্য (46,000+)

MAX378EWG+ - 8:1 Fault-Protected Multiplexer | Analog Devices
MAX378EWG+

MAX378EWG+ - 8:1 Fault-Protected Multiplexer | Analog Devices

The Analog Devices MAX378EWG+ is an 8-channel, single-ended 1-of-8 multiplexer with a specified on-resistance of 3.5 kOhm, fault protection, and a 24-pin SOIC package. The device is designed for routing one of eight analog inputs to a common output while providing protection when supply voltages are inadvertently removed from a powered system. The MAX378 uses a series N-channel, P-channel, and N-channel switch arrangement that supports fault-protected operation in demanding measurement and control circuits. A multiplexer is an analog switch that connects multiple signal sources to one destination. In the broader hierarchy of electronic components, the MAX378EWG+ is an analog multiplexer, an analog switch, an interface IC, and ultimately a semiconductor. Its eight-to-one configuration reduces the number of external signal lines needed when several sensors, voltage sources, or measurement channels must be evaluated by one downstream converter. The fault-protected architecture is particularly useful when an input may remain energized while the device's own supply rails are off. The manufacturer identifies the MAX378 as an 8-channel, high-voltage, fault-protected multiplexer and lists it in production. Its principal specifications include an 8:1 configuration, one multiplexer circuit, 3.5 kOhm on-resistance, and a 24-SOIC package. The MAX378EWG+ ordering code is listed by distributors as a 24-pin SOIC analog switch or multiplexer. The similarly named MAX379 is a different 4-channel differential multiplexer and therefore is not an interchangeable functional substitute for the single-ended MAX378. The N-channel, P-channel, and N-channel topology distinguishes this device from a basic eight-channel analog multiplexer. According to the Analog Devices MAX378 product page, the fault-protection structure causes all mux channels to turn off if the power supplies are inadvertently turned off while input voltages remain applied. This behavior limits unintended signal paths during an abnormal power sequence and is valuable in equipment where external sources can outlive the local control electronics. Typical uses include battery-powered instrumentation, industrial test equipment, data acquisition, automated measurement systems, and analog sensor interfaces. The 8:1 organization is useful when one analog-to-digital converter or measurement front end must interrogate multiple inputs without requiring a separate switch for every channel. Engineers should also account for the relatively high 3.5 kOhm on-resistance when designing sensors that require low source impedance or when calculating the resulting signal attenuation. For layout and protection, place the multiplexer near the routed analog signals, keep the selected-channel traces compact, and provide a defined return path for every switched input. Review the manufacturer's datasheet pin description, absolute maximum ratings, and typical application circuit before connecting high-voltage sources. The fault-protection feature should not be interpreted as permission to exceed those ratings or as a substitute for external surge protection. This product page consolidates the manufacturer identity, package, multiplexing configuration, fault-protection architecture, ordering information, sourcing guidance, and design considerations into an engineering-focused reference. It also distinguishes true drop-in alternatives from related devices whose channel count, signal architecture, or package implementation differs, helping PCB designers avoid substitutions that require schematic or layout changes.

RFQ যোগাযোগ
MAX379CPE+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated
MAX379CPE+

MAX379CPE+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated

The Maxim Integrated MAX379CPE+ is a high-voltage, fault-protected analog multiplexer with two 4:1 switches, a 3.5 kOhm on-resistance, and a 16-pin PDIP package. It is a differential 2-of-8 multiplexer, allowing eight source inputs to be organized into four selectable differential pairs for measurement, routing, and instrumentation systems. A multiplexer is an analog switch network that routes one of several signal sources to a common output. The MAX379 belongs to the broader analog switch and multiplexer hierarchy within interface ICs. Its differential architecture is intended for paired signals, while its 4:1 configuration provides four selections per switch. The series N-channel, P-channel, and N-channel structure is specifically designed to improve protection when the device supplies are off but external input voltages remain present. The key features of the MAX379CPE+ include its fault-tolerant input structure, two independent 4:1 circuits, and 3.5 kOhm switch resistance. Differential routing reduces the influence of common-mode effects when paired signals are measured together. The high-voltage, fault-protected design is useful when transient or powered-off conditions could otherwise stress the input network. Two circuits in one package also reduce board area compared with separate single-ended or differential switch assemblies. Technically, the MAX379 is described as an 8-channel, high-voltage, fault-protected multiplexer. The manufacturer identifies the MAX379 as a four-channel differential, 2-of-8 multiplexer, while the MAX378 in the same family is an eight-channel single-ended, 1-of-8 device. During an unintended power-off condition, the MAX379 channels turn off and the input current falls to only a few nanoamperes. This behavior helps isolate applied signals from the internal switching path when supply power is absent. Typical uses include automated test equipment, data-acquisition systems, battery or power-system monitoring, industrial control interfaces, and laboratory measurement equipment. The differential configuration is especially appropriate for bridge sensors, paired analog channels, and systems where a common measurement reference is required. PCB layout should preserve the pin assignments of the 16-pin PDIP package and route high-impedance analog nodes with short, guarded traces. Check signal amplitude and fault conditions against the manufacturer operating limits before connecting external sources. Because this is a through-hole package, component height, lead spacing, and connector orientation also require mechanical validation. This product page combines the manufacturer function description, exact distributor package and resistance information, lifecycle context, and practical guidance for selecting, sourcing, and implementing the MAX379CPE+ in analog-routing systems.

RFQ যোগাযোগ
MAX379CWG+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated
MAX379CWG+

MAX379CWG+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated

The Maxim Integrated MAX379CWG+ is a high-voltage, fault-protected analog multiplexer with two 4:1 circuits, an on-resistance of 3.5 kOhm, and a 24-pin SOIC package. It selects four differential signal pairs, or eight single-ended inputs in differential operating mode, making it suitable for routing controlled signals in instrumentation, test, measurement, and industrial systems. The MAX379 family is designed to limit fault-current exposure when input voltages remain present while the device supplies are turned off. An analog multiplexer is an interface IC that connects multiple signal paths to a smaller number of shared pins. The MAX379 belongs to the broader multiplexer hierarchy, where its differential 4:1 architecture reduces the number of external connections required by a system with several paired inputs. This is particularly useful when board space, connector count, or routing complexity must be controlled without sacrificing selectable signal channels. Key features include two independent 4:1 circuits, 3.5 kOhm on-resistance, an eight-channel high-voltage fault-protected configuration, and operation from dual supply rails. The manufacturer describes the implementation as a series N-channel, P-channel, and N-channel structure. This arrangement provides meaningful fault protection by turning the channels off when the supplies are removed while signal inputs can still be present, limiting unintended current paths. The MAX379CWG+ is a differential rather than single-ended multiplexer. Each selected channel can carry a pair of related signals, supporting balanced measurement, instrumentation, or test systems where signal polarity and common-mode behavior matter. Its 24-pin SOIC footprint is a surface-mount package intended for conventional PCB assembly, while the operating limits and exact channel ratings should be checked against the manufacturer datasheet before using it outside laboratory voltages. Typical uses include automated test equipment, data-acquisition systems, industrial control interfaces, oscilloscope input routing, and multichannel sensor conditioning. It is particularly appropriate when multiple high-impedance sources must be connected to downstream instrumentation. Designers should account for the 3.5 kOhm on-resistance, assess leakage and off-channel behavior, and ensure that external circuitry keeps faulted inputs within the absolute maximum ratings. For a robust layout, place the device close to the multiplexer bus and use a quiet ground-plane connection. Signal traces should avoid crossing high-current switching paths, and unused inputs should be handled according to the datasheet guidance. Supply decoupling must follow the manufacturer recommendation, while external series resistance may be needed to limit fault current in higher-energy systems. This product summary combines the manufacturer's device description with package, interface, and application analysis, helping engineers identify whether the MAX379CWG+ provides the required differential channel count and fault-protected behavior. The accompanying comparison, pinout, sourcing, and design guidance make the selection process more practical than a basic distributor listing alone.

RFQ যোগাযোগ
MAX381CPE+ - Dual 35Ω SPST Analog Switch | Maxim Integrated
MAX381CPE+

MAX381CPE+ - Dual 35Ω SPST Analog Switch | Maxim Integrated

Maxim Integrated MAX381CPE+ is a dual, single-pole single-throw normally open CMOS analog switch with 35 Ω on-resistance, supplied in a 16-pin PDIP package. The device operates from 3 V to 15 V, supports single-supply or bipolar operation, and is designed to route low-voltage analog signals with low on-resistance and rail-to-rail signal handling. A CMOS analog switch is an integrated semiconductor device that uses controlled transistors to connect or disconnect an analog signal path. The MAX381/MAX383/MAX385 family comprises precision, low-voltage switches for instrumentation, test equipment, control systems, and signal-routing applications. Within the broader semiconductor hierarchy, an analog switch belongs to the interface-IC category and provides a controllable connection between an input terminal and an output terminal. The MAX381CPE+ contains two independent SPST, normally open switch circuits in a 1:1 configuration. Its specified 35 Ω on-resistance minimizes signal attenuation in moderate-impedance analog systems. The device also features matched channels, with a specified channel-to-channel on-resistance matching of 500 mΩ, helping preserve balance in differential or dual-channel signal paths. Analog-signal performance includes charge injection of 2 pC, off-state channel capacitance of 12 pF, and crosstalk of -90 dB at 1 MHz. The MAX381 family supports both single-supply and bipolar-supply operation, allowing the switch to process signals referenced to ground or operate within positive and negative voltage rails. Its normally open configuration keeps the switched paths disconnected when the control state is inactive. Typical uses include precision measurement front ends, automated test equipment, sensor signal routing, sample-and-hold circuits, and industrial control systems. The two integrated switches can route two related channels when matched behavior is useful, or independently route separate low-voltage signals. The 16-pin PDIP package also supports through-hole prototyping and legacy industrial equipment where surface-mount conversion would be inconvenient. When laying out a design, place the IC close to the switched signal paths and keep analog traces short to minimize parasitic capacitance and interference. Treat the control inputs as logic signals while ensuring that every driven input remains within the device's specified supply-voltage limits. Verify signal amplitude, bandwidth, charge injection, and off-state leakage against the application before committing to a high-impedance instrumentation design. This product page combines the MAX381CPE+ electrical characteristics, package details, lifecycle information, sourcing workflow, application guidance, and verified cross-reference analysis. It also distinguishes true pin-and-package drop-in options from related switches that use different packages or implement different circuit topologies.

RFQ যোগাযোগ
MAX383CPE+ - Dual SPDT 35Ω Analog Switch | Analog Devices
MAX383CPE+

MAX383CPE+ - Dual SPDT 35Ω Analog Switch | Analog Devices

The Analog Devices MAX383CPE+ is a precision, low-voltage CMOS analog switch containing two independent single-pole double-throw channels, a maximum on-resistance of 35Ω, and a 16-pin PDIP package. It operates from 3V to 15V, supports supply configurations of ±3V to ±8V, and is specified for commercial temperatures from 0°C to +70°C. An analog switch is an electronic routing device that connects one signal terminal to one of two alternatives under digital control. A single-pole double-throw switch, or SPDT, has one common terminal and two switched terminals. The MAX383 places two SPDT switches in one 16-pin package, placing it in the hierarchy of CMOS analog switches, analog multiplexers, interface ICs, and semiconductor signal-routing components. Each MAX383 channel has one normally open and one normally closed path. According to the manufacturer product page, the on-resistance is less than 35Ω, channel matching is guaranteed within 2Ω, and the resistance remains flat over the operating signal range. These characteristics make the matched channels useful when amplitude accuracy across a dual-channel path is more important than minimizing resistance absolutely. The MAX383 family supports both single-supply and dual-supply operation. Its specified turn-on and turn-off times are 175ns and 100ns, respectively, enabling controlled signal routing with relatively little transition delay. The low-voltage CMOS implementation is suited to battery-powered, industrial control, instrumentation, and test-equipment systems where low-voltage logic and analog signals share the same board. Typical uses include selecting between two sensor channels, routing test signals, switching bipolar or unipolar analog inputs, and implementing sample-and-hold paths. Two integrated SPDT switches can route complementary or paired signals while keeping channel timing and resistance characteristics closely matched. Designers should maintain the specified 3V to 15V supply range, use pull-up or pull-down resistors where control or common-pin states require defined levels, and account for charge injection and off-state leakage when switching high-impedance or precision measurement circuits. The through-hole PDIP-16 package also simplifies prototype assembly and legacy PCB maintenance. This page combines manufacturer specifications, matched-channel design guidance, sourcing information, package details, and same-family replacement analysis to support practical analog-switch selection beyond a basic distributor parameter summary.

RFQ যোগাযোগ
MAX383CSE+ - Dual Precision SPDT Analog Switch | Analog Devices
MAX383CSE+

MAX383CSE+ - Dual Precision SPDT Analog Switch | Analog Devices

The Analog Devices MAX383CSE+ is a dual precision, low-voltage CMOS analog switch with two independently controlled single-pole double-throw channels, less than 35 ohm on-resistance, and operation from +3 V to +15 V. The device is packaged in a 16-pin SOIC for surface-mount designs that require low-leakage, low-charge-injection signal routing. An analog switch is a semiconductor device that connects or disconnects an electrical signal path under digital control. The MAX383 belongs to the analog-switch and multiplexer hierarchy, combining low-voltage CMOS construction with precision on-resistance characteristics. Its two SPDT switches can select between two signal sources for each channel, making the device useful for analog signal multiplexing, source selection, test-equipment routing, and bidirectional signal-path control. Key characteristics include on-resistance below 35 ohm, channel-to-channel matching within 2 ohm, flat on-resistance across the specified analog signal range, and operation in either single-supply or bipolar-supply systems. According to the Analog Devices MAX383 product page, the MAX381, MAX383, and MAX385 family uses precision, low-voltage analog switches, while the MAX383 specifically provides two normally open and two normally closed poles. This switching arrangement supports complementary routing rather than simple on/off isolation. The MAX383 supports +3 V to +15 V single-supply operation and ±3 V to ±8 V bipolar-supply operation. These ranges make it appropriate for low-voltage instrumentation, industrial control, communications, and measurement systems. Its low on-resistance can reduce signal attenuation, while matched channels help minimize path-to-path gain variation. The guaranteed charge injection of less than 5 pC and off-channel leakage below 2.5 nA at +85 °C are particularly useful when switching precision or high-impedance signals. Analog Devices also identifies the MAX383 as pin-compatible with the DG401, DG403, and DG405. These compatibility relationships allow engineers to evaluate the MAX383 in existing routed designs while still checking control logic, supply level, signal range, and electrical limits against the complete manufacturer datasheet. The device also supports TTL/CMOS-compatible logic, making it practical to combine with common microcontroller and digital control systems. PCB implementation requires care around high-impedance nodes. Keep routing short, provide a stable ground reference, and avoid placing sensitive analog traces beside fast digital or switching-converter paths. Input and output traces should not be forced beyond the device's absolute-maximum ratings, and control inputs must remain within their specified logic thresholds. The SOIC-16 outline supports conventional surface-mount assembly and provides adequate routing space for two complete SPDT channels. This page consolidates manufacturer specifications, package details, sourcing guidance, and design-oriented guidance into one engineering reference. It also identifies verified pin-compatible options while clearly separating exact drop-in candidates from functionally related devices that require a different package or a full electrical review.

RFQ যোগাযোগ
MAX388CWG+ - 8:1 18V Analog Multiplexer | Analog Devices
MAX388CWG+

MAX388CWG+ - 8:1 18V Analog Multiplexer | Analog Devices

Analog Devices MAX388CWG+ is a single-ended, 8-channel CMOS analog multiplexer with an 8:1 configuration, 3 kohm on-state resistance, and a 4.5V to 18V supply range. The device is offered in a 24-pin SOIC package for surface-mount instrumentation and test systems. Its eight-channel single-ended architecture lets one source be routed to eight analog inputs, while the high-voltage operating range supports signals and control circuits above conventional low-voltage logic levels. An analog multiplexer is an interface IC that connects multiple signal paths to a shared processing channel through controlled switches. The MAX388CWG+ belongs to the broader multiplexer and switch family within the semiconductor hierarchy. By selecting one of eight inputs for a common output, it can reduce the number of dedicated input channels required by a measurement, control, or signal-routing system while preserving a compact PCB footprint. Key specifications include an 8:1 multiplexing configuration, one multiplexed function, eight channels, 3 kohm on-state resistance, and operation from 4.5V to 18V. The CMOS implementation supports integration with digital control logic, while the 24-pin SOIC package is compatible with conventional surface-mount assembly. The MAX388CWG+ is identified as a commercial-temperature-grade part for general-purpose equipment applications. The MAX388CWG+ is based on a single-ended analog switching arrangement rather than a differential multiplexer. This makes it suitable when the system has one common signal bus and multiple inputs to route, provided that the source impedance and downstream amplifier account for the 3 kohm on resistance. The 4.5V to 18V supply span gives designers room for both lower-voltage precision systems and higher-voltage industrial signal environments. Typical applications include automated test equipment, data-acquisition systems, instrumentation control, industrial measurement interfaces, battery and power-system monitoring, and signal routing in industrial controllers. The eight-input structure is especially useful when a controller must inspect several sensors or conditioned analog channels through one shared converter or measurement front end. A key design consideration is that every signal passing through the selected switch sees the device's 3 kohm on-state resistance. Source impedance, amplifier bias current, capacitance, settling time, and injected noise should therefore be evaluated together. Keep routed analog traces short, maintain a common ground reference, and place input and supply bypassing close to the device to preserve measurement stability. This product page consolidates the MAX388CWG+ electrical identity, ordering-code distinction, sourcing information, and application guidance. It also provides the practical selection criteria and design considerations needed to determine whether this 8:1 CMOS multiplexer is appropriate for a particular analog-routing architecture.

RFQ যোগাযোগ
MAX388EPN+ - 8:1 3kOhm Analog Multiplexer | Analog Devices
MAX388EPN+

MAX388EPN+ - 8:1 3kOhm Analog Multiplexer | Analog Devices

The Analog Devices MAX388EPN+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 3 kOhm on-resistance and an 18-pin PDIP package. The device uses internal data latches to hold the selected channel, allowing control signals to change the active input without disrupting the selected analog path. Its high-voltage, N-channel, P-channel, N-channel switch architecture improves fault protection when voltage remains present after the device power is removed. An analog multiplexer is an interface IC that routes one of several analog inputs to a shared output. The MAX388 family combines an 8:1 single-ended multiplexer with internal selection latches, placing it in the interface IC hierarchy alongside analog switches, mux/demux devices and signal-routing components. This makes the device useful when several sensor, measurement, or control signals must share a limited number of converter inputs. Key features include an 8:1 multiplexing ratio, 3 kOhm on-resistance and a high-voltage fault-protected architecture. The internal latches remove the need to hold a control input in a defined state after selection. The product family also provides an off behavior when power is removed but input voltages remain applied, allowing all channels to turn off and limiting unintended signal paths. The MAX388EPN+ is specifically listed in an 18-pin PDIP package. The MAX388 family uses a high-voltage series N-channel, P-channel, N-channel structure rather than a conventional single-polarity switch arrangement. This topology is specifically intended to improve fault protection in systems where external inputs can exceed the supply voltage or where power can be removed before the analog signals. The 3 kOhm on-resistance is appropriate for medium-impedance sensor and instrumentation paths, although system gain, leakage and settling requirements must be evaluated in the complete signal chain. Typical uses include multi-sensor signal selection, instrumentation measurement multiplexing, industrial control signal routing, test-equipment input selection and embedded analog measurement systems. The latched channel selection is especially useful when a host controller writes a channel address and then performs an analog conversion. In these systems, the mux reduces the number of analog input channels required at the converter while preserving a defined route through the selected switch. Designers should confirm the absolute maximum input and supply ratings, channel leakage, off isolation, on-state resistance tolerance and acquisition settling time in the manufacturer datasheet before finalizing signal paths. Input and ground connections should be arranged to minimize coupling between adjacent channels, and unused digital control inputs should be driven to valid logic levels. Because the MAX388 family is obsolete, long-life programs should verify availability, alternate sourcing and any required qualification before release to production. This product page consolidates the confirmed switch ratio, on-resistance, package, fault-protection architecture and lifecycle information with practical design guidance. It also identifies the limited number of verified drop-in alternatives, helping engineers distinguish a true pin-compatible replacement from a broader functional equivalent before modifying an existing 18-pin PCB layout.

RFQ যোগাযোগ
MAX389CWG+ - 4:1 Fault-Protected Analog MUX | Analog Devices
MAX389CWG+

MAX389CWG+ - 4:1 Fault-Protected Analog MUX | Analog Devices

The Analog Devices MAX389CWG+ is a dual-circuit, 4:1 analog multiplexer in a 24-pin SOIC package, featuring a 3 kOhm on-resistance and fault-protected high-voltage analog switching. Its two independent switch circuits make it suitable for routing multiple analog signals through a shared measurement or control channel without introducing an external discrete protection network. The manufacturer positions the MAX389 family as high-voltage, fault-protected analog multiplexers. An analog multiplexer is a switching interface that connects one of several inputs to a shared output. In the signal-chain hierarchy, the MAX389CWG+ belongs to the analog switch and multiplexer category, where fault protection and high-voltage tolerance help isolate external circuitry from downstream measurement channels. The 24-SOIC footprint provides a conventional surface-mount option for instrumentation, industrial control, and test equipment designs. Key features include two switching circuits, a 4:1 configuration, and 3 kOhm on-resistance. The 4:1 arrangement allows four input paths to be selected for each of two circuits, while the fault-protected architecture is intended to improve system robustness when connected to external analog sources. Its surface-mount SOIC package supports automated assembly and compact PCB layouts, although the relatively long 24-pin footprint requires more board area than modern leadless packages. MAX389 devices are used where analog signals must be routed before measurement, excitation, conversion, or control. Typical signal types include sensor outputs, external test points, and conditioned analog inputs. The integrated protection function is especially relevant when a selected channel connects to a source that may carry a higher voltage than the downstream circuitry expects. Board design must still include suitable grounding, decoupling, and protection around the selected pins. Typical applications include automated test equipment, process-control interfaces, laboratory measurement systems, data acquisition modules, and industrial sensor-conditioning boards. The 24-pin SOIC package is appropriate where a proven through-hole-style lead arrangement and external prototyping access are more valuable than minimum board area. When laying out the PCB, route each mux channel as a short, guarded analog trace and place input protection close to the connector. Confirm the absolute maximum ratings and switch-state behavior in the manufacturer datasheet before applying external voltages. This page consolidates package details, sourcing guidance, drop-in alternatives, and practical layout considerations for engineers evaluating the MAX389CWG+.

RFQ যোগাযোগ
MAX389EPN+ - 4:1 Differential Multiplexer | Analog Devices
MAX389EPN+

MAX389EPN+ - 4:1 Differential Multiplexer | Analog Devices

The Analog Devices MAX389EPN+ is a dual 4:1 analog multiplexer IC with an on-resistance of 3 kOhm, supplied in an 18-pin PDIP package. It is designed as a differential multiplexer for routing analog signals while adding the fault-protection function identified in the MAX389 family documentation. The device belongs to the interface IC hierarchy and provides a practical way to connect multiple signal sources to downstream analog measurement or control circuitry. An analog multiplexer is an interface IC that selects one of several input paths and connects it to an output. A 4:1 configuration gives the MAX389EPN+ four input positions per internal switch, while the two-circuit designation identifies the two switching sections used by this differential implementation. This arrangement can reduce the number of separate signal paths required in instrumentation, test systems, and other analog-routing designs. The primary verified characteristics of the MAX389EPN+ are its dual-circuit organization, 4:1 multiplexing ratio, 3 kOhm on resistance, differential operating arrangement, industrial temperature grade, and 18-pin PDIP construction. The PDIP format uses through-hole mounting and provides generous pin spacing for laboratory, industrial control, educational, and legacy equipment designs where surface-mount assembly is not required. The MAX389 family documentation identifies these devices as high-voltage, fault-protected analog multiplexers. That positioning makes signal-path protection an important part of circuit planning because the selected switch must tolerate the voltage and fault conditions present in the intended system. Engineers should use the manufacturer datasheet for the complete absolute maximum ratings, switching characteristics, channel configuration, control logic, and truth table before finalizing a high-energy analog front end. Typical uses include routing differential sensor signals, selecting test points in automated measurement systems, multiplexing analog channels in industrial control equipment, and connecting external instrumentation to a shared processing chain. Because the verified information identifies a differential 4:1 architecture, the part is particularly relevant to circuits that need paired signal routing rather than a single-ended selector. PCB design should preserve the through-hole footprint of the 18-pin PDIP package and route sensitive analog traces away from switching nodes and other high-energy circuitry. Confirm the exact pin numbering, control inputs, common-mode limits, and maximum signal voltage in the manufacturer datasheet before fabrication. This page combines the verified device identity, package and switching characteristics with drop-in comparison information and practical guidance for industrial analog-routing designs. It distinguishes confirmed specifications from parameters that must be checked directly in the MAX389EPN+ datasheet.

RFQ যোগাযোগ
MAX391CSE+ - Precision Quad SPST Analog Switch | Analog Devices
MAX391CSE+

MAX391CSE+ - Precision Quad SPST Analog Switch | Analog Devices

Analog Devices MAX391CSE+ is a precision quad, SPST analog switch with four independently controlled normally closed channels, a typical on-resistance of 20 Ω, and a 16-pin narrow SOIC package. It operates from a single +3 V to +15 V supply or from dual ±3 V to ±8 V supplies, making it suitable for low-power instrumentation and precision signal-routing systems. An analog switch is an integrated semiconductor device that routes electrical signals between input and output terminals under digital control. The MAX391 belongs to the hierarchy analog switch → interface IC → semiconductor and is commonly used where a compact, low-power signal multiplexer must present low resistance and limited charge injection. Its four SPST channels provide independent routing rather than requiring one multiplexer to share a common terminal. Key electrical characteristics include a 20 Ω typical on-resistance, guaranteed matching between channels, less than 2 Ω guaranteed on-resistance flatness over the signal range, maximum charge injection of 4 pC, and leakage below 2.5 nA at +85 °C. The manufacturer specifies ESD withstand above 2000 V by Method 3015.7, while power consumption remains below 1 µW. These characteristics support accurate acquisition, measurement, and control circuits where switch-induced error must remain small. The MAX391 architecture uses complementary analog switches to provide normally closed operation and balanced switching behavior. Its specified on-resistance matching and flatness reduce gain variation between channels, while low charge injection limits timing errors when the device switches bipolar or high-impedance signals. The low-leakage specification is particularly useful in multiplexed measurement systems where off-state input current can create errors in high-impedance nodes. Typical uses include battery-powered measurement systems, precision signal routers, automated test equipment, data acquisition modules, and industrial control interfaces. The +3 V to +15 V single-supply range supports modern low-voltage systems, while ±3 V to ±8 V dual-supply operation allows direct handling of bipolar signals without shifting the common-mode range. The 16-pin narrow SOIC package also simplifies assembly on conventional surface-mount PCB layouts. When laying out a MAX391CSE+ circuit, keep analog input and output traces short, provide a stable ground reference, and place supply bypass capacitance close to the device. Consider the off-state leakage when the source impedance is high, because the specified 2.5 nA maximum at +85 °C can create an error comparable to several nanovolts across a megohm-scale source impedance. Use the manufacturer pin description and package drawing when making PCB assignments. This product guide combines the MAX391CSE+ electrical characteristics, operating limits, package details, verified sourcing information, and practical design guidance. It also distinguishes true pin-compatible alternatives from functionally related devices, helping engineers evaluate replacement options without introducing a different footprint or unacceptable on-resistance change.

RFQ যোগাযোগ
MAX392CSE+ - Quad SPST Analog Switch, 20 Ohm, 16-SOIC | Analog Devices
MAX392CSE+

MAX392CSE+ - Quad SPST Analog Switch, 20 Ohm, 16-SOIC | Analog Devices

The Analog Devices MAX392CSE+ is a precision quad SPST analog switch with 20 Ω typical on-resistance, 4 pC maximum charge injection and less than 1 µW of power consumption, packaged in a 16-pin SOIC (CSE) package. An analog switch, also called an analog multiplexer or solid-state relay, is a semiconductor device that routes a signal from one node to another under digital control without moving the signal physically. The MAX392 belongs to the product hierarchy analog switch > multiplexer > interface IC > integrated circuit. Each of the four independent switches in the MAX392 is a single-pole single-throw (SPST) type, so it provides a simple on/off path for analog signals rather than a multi-channel selection function. Key features of the MAX392 family include guaranteed on-resistance matching between channels below 2 Ω, on-resistance flatness over the signal range below 4 Ω, charge injection limited to 4 pC maximum, and improved off leakage of less than 2.5 nA at +85 °C. The part operates from a single +3 V to +15 V supply or from dual bipolar supplies of ±3 V to ±8 V, which allows it to sit alongside both modern low-voltage digital rails and legacy ±5 V analog instrumentation. Internally the device uses MOSFET pass elements switched by CMOS control logic, which keeps the control input compatible with standard TTL and CMOS levels. The very low power consumption of less than 1 µW per switch makes the MAX392 attractive for battery-powered and portable measurement systems where leakage and standby draw dominate the power budget. Electrostatic discharge withstand above 2000 V per Method 3015.7 protects the pins during handling and board assembly. Typical applications include precision test and measurement multiplexing, audio and low-level signal routing in instrumentation, industrial process control module switching, and general-purpose analog signal isolation in data acquisition systems. The quad SPST arrangement lets one package handle four separate signal paths, which reduces both board area and the number of control lines needed. When designing with the MAX392CSE+, pay attention to the negative rail requirement in dual-supply operation and to off-state leakage when the switched node sits near the supply rails. Place the device close to the source and destination so that trace capacitance does not degrade the small charge-injection and switching-glitch performance that make this switch precise in the first place. This page brings together parametric detail, package information, drop-in alternatives and practical design notes so that engineers can qualify the MAX392CSE+ for a precision analog switching requirement without having to piece the data together from several documents.

RFQ যোগাযোগ
MAX393CPE+ - 35 Ohm Quad SPST Analog Switch | Maxim
MAX393CPE+

MAX393CPE+ - 35 Ohm Quad SPST Analog Switch | Maxim

The Maxim Integrated MAX393CPE+ is a precision, quad SPST analog switch with four independently controlled 1:1 channels, 35 ohm maximum on-resistance, and a 16-pin PDIP package. It operates from a single +3 V to +15 V supply or from dual ±3 V to ±8 V rails. The MAX393 family supports 130 ns maximum on-time and 75 ns maximum off-time, making it suitable for precision signal routing, instrumentation, and test systems. An analog switch is an integrated semiconductor device that connects or disconnects an electrical signal path under logic control. The MAX393CPE+ belongs to the analog-switch hierarchy within interface ICs, where multiplexers and switches route sensors, test points, and control signals without the conversion noise associated with mechanical relays. Each of its four channels provides a normally open SPST connection with matching on-resistance characteristics. Key electrical features include 20 ohm typical on-resistance, less than 2 ohm guaranteed on-resistance matching between channels, and less than 2 ohm guaranteed on-resistance flatness across the signal range. Maximum charge injection is 4 pC, which limits control-signal-induced voltage steps in precision measurement paths. Leakage current is below 2.5 nA at +85 °C, and the specified operating temperature range is 0 °C to +70 °C. The MAX393 operates from +3 V to +15 V in single-supply configurations and from ±3 V to ±8 V in bipolar configurations. Its precision SPST topology makes each switch independent, allowing one control signal to be asserted without changing the conductive state of the other three channels. This is useful in multiplexed test systems, where consistent channel resistance simplifies calibration of downstream amplifiers and converters. Typical uses include automated test equipment, data-acquisition front ends, sample-and-hold instrumentation, signal-routing modules, and precision measurement interfaces. Because the device is specified for 0 °C to +70 °C, it is best suited to commercial and industrial indoor environments rather than extended-temperature or automotive environments. When laying out a board, route each switched signal as a short, guarded trace and keep the four control inputs away from sensitive analog nets. Use a ground plane for return currents and place the device where the switched signals can reach the connector or measurement circuitry without crossing digital control traces. Verify the logic-high and logic-low input levels against the selected supply configuration before relying on the stated switching timing. This page combines the manufacturer device information with distributor package and ordering details, structured electrical characteristics, application guidance, and a pin-to-pin comparison of the MAX393 switching family. It also identifies the trade-offs involved when choosing this PDIP precision switch for new designs.

RFQ যোগাযোগ
MAX393EPE - Quad SPST Analog Switch | Analog Devices
MAX393EPE

MAX393EPE - Quad SPST Analog Switch | Analog Devices

The Analog Devices MAX393EPE is a precision, quad, single-pole single-throw analog switch with a typical low on-resistance of 20 Ω, guaranteed on-resistance matching below 2 Ω, and guaranteed on-resistance flatness below 2 Ω across the signal range. The device is packaged in a 16-pin through-hole DIP and supports single-supply operation from +3 V to +15 V or bipolar operation from ±3 V to ±8 V. An analog switch is an electronically controlled semiconductor interconnect that routes a signal between circuit nodes while providing high impedance in its open state. The MAX393 belongs to the analog-switch hierarchy within interface ICs. Its four independent SPST switches are intended for precision signal routing where low channel-to-channel resistance variation, controlled charge injection, low leakage, and low power consumption are important. Key electrical characteristics include a typical on-resistance of 20 Ω, on-resistance matching below 2 Ω, on-resistance flatness below 2 Ω, and power consumption below 1 µW. The Analog Devices MAX393 product page lists single-supply operation over +3 V to +15 V, bipolar operation over ±3 V to ±8 V, and electrostatic-discharge withstand above 2000 V per Method 3015.7. These characteristics distinguish the device from higher-resistance general-purpose switch arrays. The four switches are designed to preserve signal integrity when a system changes source or measurement paths. Tight on-resistance matching limits gain or attenuation differences between channels, while flat on-resistance reduces signal-dependent distortion as the analog input changes. The MAX393EPE uses a 16-pin DIP package for through-hole assembly, providing ample spacing between pins and straightforward socket or PCB mounting in laboratory and industrial equipment. Typical uses include precision test and measurement systems, data-acquisition input networks, industrial instrumentation, sample-and-hold circuits, and controlled analog-signal routing. The part can operate from a single positive supply or from split bipolar rails, allowing it to fit both compact single-supply designs and instrumentation with bipolar signal ranges. Its low power consumption is especially useful when the switched signals are not continuously active. A critical design consideration is to keep control-signal transitions away from sensitive analog traces because charge injection can create a temporary output disturbance when a switch changes state. Confirm that the selected supply configuration, input voltage, control logic level, and signal amplitude satisfy the MAX393 absolute-maximum and operating limits in the manufacturer data sheet before finalizing the circuit. This page combines the manufacturer’s MAX393 electrical characteristics with package details, practical routing guidance, application analysis, and same-package replacement considerations. It is structured to help engineers evaluate the MAX393EPE for precision analog switching without relying on a generic catalog summary.

RFQ যোগাযোগ
MAX394CAP+ - Quad SPDT 35Ω Analog Switch | Analog Devices
MAX394CAP+

MAX394CAP+ - Quad SPDT 35Ω Analog Switch | Analog Devices

The Analog Devices MAX394CAP+ is a low-voltage, quad SPDT CMOS analog switch with four independently selectable 2:1 channels, a 35 Ω on-resistance, and a 20-pin SSOP package. The device supports a 5 V supply, 130 ns maximum on-time, 75 ns maximum off-time, and 200 pA maximum off leakage. These characteristics make it suitable for routing low-voltage analog signals in test, measurement, communication, and industrial control systems. A CMOS analog switch is a semiconductor device that uses MOSFETs to connect or disconnect signal paths under digital control. The MAX394 belongs to the broader analog switch and multiplexer hierarchy, which sits within interface ICs and semiconductor signal-routing components. Each SPDT channel can select one of two signal sources or route a common node to a selected destination, depending on the application and external connection arrangement. The MAX394CAP+ provides four 2:1 switch circuits with a specified 35 Ω on-resistance. Its low-voltage operation is suitable for systems using 5 V-powered logic and low-level analog signals. The 130 ns on-time and 75 ns off-time provide fast transition behavior, while break-before-make operation helps prevent two switched paths from conducting simultaneously during changeover. The 200 pA off-leakage specification supports low-level measurement and sampling circuits. The 20-SSOP package provides a compact surface-mount footprint for multiplexed analog routing. Because the package is not thermally exposed, board layout and ambient conditions remain important when multiple channels switch continuously. Signal integrity is influenced by source and load impedance, cable or trace capacitance, supply bypassing, and the timing of control signals. The device’s analog characteristics should therefore be evaluated together with the complete signal path rather than treated as isolated switch ratings. Typical uses include multimeter and oscilloscope input routing, data-acquisition systems, communication-interface signal multiplexing, automated test equipment, and industrial measurement modules. The four channels can support parallel routing or switching functions, reducing the number of discrete relays or mechanical switch elements required on a compact instrument board. The device is also useful when a circuit must select between sensors, amplifiers, or external test signals. Designers should place the supply bypass capacitor close to the device and route high-impedance signal traces away from switching-node outputs to minimize coupling. Control signals should meet the device’s input logic levels, and unused inputs should be connected to defined potentials rather than left floating. Confirm that source and load voltages remain within the device’s absolute maximum ratings and signal limits before finalizing the analog front end. This page combines the MAX394CAP+ device specifications, sourcing guidance, functional comparison, and application-focused design notes to support faster component selection and PCB implementation. It also distinguishes exact drop-in interchangeability from merely similar analog switches, helping engineers preserve package, pinout, timing, and channel requirements during redesigns.

RFQ যোগাযোগ
MAX394EPP+ - 4-Channel SPDT 35Ω Switch | Analog Devices
MAX394EPP+

MAX394EPP+ - 4-Channel SPDT 35Ω Switch | Analog Devices

The Analog Devices MAX394EPP+ is a low-voltage, quad, SPDT CMOS analog switch with four independent channels, 35Ω on resistance, and a 20-pin PDIP package. It accepts bipolar supplies from ±2.7V to ±8V or a single supply from +2.7V to +15V, making it suitable for routing low-voltage analog and digital signals where multiple signal paths must be selected. A CMOS analog switch is an electrically controlled pass-device multiplexer that connects one signal terminal to one of two alternatives. The SPDT configuration provides a common terminal and two switched terminals per channel. As part of the semiconductor hierarchy, the MAX394 belongs to the integrated-circuit, interface-IC, analog-switch, and multiplexer families used to route signals between sensors, converters, amplifiers, test equipment, and system controllers. The MAX394 uses a low-voltage silicon-gate process and is designed to provide low power consumption of 10μW and extremely low charge injection of 10pC. Its ESD protection exceeds 2000V. The four on-resistance channels are matched closely, helping minimize gain and timing variation when the same switch network handles several related signals. The MAX394EPP+ also replaces the MAX333A according to the manufacturer product page. Dual-supply operation allows the switch to pass signals around ground without requiring a mid-supply reference, while single-supply operation supports systems with a +2.7V to +15V rail. The device provides four independent switching sections rather than a multiplexed shared path, allowing each channel to select its own source. Control inputs determine which terminal is connected to the corresponding common terminal, with actual transition behavior, logic levels, and timing defined by the manufacturer datasheet. Typical uses include precision test-and-measurement systems, data-acquisition front ends, battery-powered instrumentation, industrial control interfaces, and low-voltage communication equipment. The 20-pin PDIP format also makes the device practical for prototypes, legacy industrial equipment, and hand-assembled test boards where a surface-mount package would complicate inspection or rework. For reliable operation, confirm the control-logic levels against the supply configuration and observe the absolute maximum ratings before applying signals. Keep connected external circuitry within the specified common-mode range, route high-impedance nodes conservatively, and account for charge injection when changing channel state. The DIP package should also be protected from conductive contamination and cleaned with an appropriate solvent during maintenance. This page consolidates the manufacturer switch specifications, lifecycle status, package details, engineering guidance, and documented comparison points into a design-oriented reference. It also distinguishes the PDIP MAX394EPP+ from surface-mount MAX394 variants, helping engineers confirm footprint and ordering requirements before beginning a PCB or replacement design.

RFQ যোগাযোগ
MAX395CNG+ 8-Channel SPST Analog Switch | Maxim Integrated
MAX395CNG+

MAX395CNG+ 8-Channel SPST Analog Switch | Maxim Integrated

Analog Devices MAX395CNG+ is an 8-channel, serially controlled SPST analog switch with 100 ohm on-resistance, a 2.7 V to 16 V supply range, and a 24-pin PDIP package. It combines eight independently controlled switches with a serial shift register for compact signal-routing designs. An analog switch is an electronic semiconductor device that connects or disects analog signal paths under digital control. Within the product hierarchy, the MAX395CNG+ is an analog switch IC, also described as a multiplexer or switch array. Its eight SPST channels can route low-voltage signals in test equipment, instrumentation, control systems, data acquisition, and embedded measurement products without requiring eight separate mechanical or discrete switch devices. The MAX395CNG+ uses a serial interface compatible with SPI, QSPI, and MICROWIRE protocols. Data enters at DIN and is clocked synchronously into the internal shift register on the rising edge of SCLK, allowing the eight switch states to be loaded from a host processor. The 2.7 V to 16 V operating supply supports low-voltage systems, while the cited dual-supply operating range extends from ±2.7 V to ±8 V for bipolar signal applications. Eight separately controlled SPST switches provide 1:1 routing for each channel. The manufacturer describes the MAX395 as electrically equivalent to two MAX391 quad switches controlled by a serial interface. This architecture consolidates channel control into one package and is particularly useful when a design needs multiple analog paths to share a common serial-control structure. Typical applications include automated test equipment, analog measurement systems, industrial control interfaces, programmable signal-routing boards, and compact data-acquisition equipment. The serial architecture is useful when the number of host GPIO pins is limited, while the 24-pin PDIP package simplifies prototyping, inspection, and through-hole assembly. Designers should account for the control signal levels, supply sequencing, and signal amplitudes applied to each switched node. Because the MAX395 uses edge-triggered serial loading, the host must clock the intended bit pattern in the correct order and keep SCLK stable around each rising edge. The MAX395CNG+ also requires board-space allocation for a through-hole 24-pin package rather than a compact surface-mount land pattern. This product overview combines the manufacturer's device description with practical guidance on serial control, routing architecture, package considerations, and verified drop-in alternatives. It is intended to help engineers identify whether an eight-channel serially addressed switch fits a new analog-routing design before beginning board layout.

RFQ যোগাযোগ
MAX395EAG+ - 8-Channel Serial SPST Switch | Analog Devices
MAX395EAG+

MAX395EAG+ - 8-Channel Serial SPST Switch | Analog Devices

The Analog Devices MAX395EAG+ is a serially controlled, 8-channel single-pole single-throw analog switch with a maximum on-resistance of 100 ohm, operating from 2.7 V to 16 V and housed in a 24-pin SSOP package. Each of its eight switches can be controlled independently through a serial shift-register interface compatible with SPI, QSPI, and MICROWIRE protocols. An analog switch is a semiconductor device that routes analog or digital signals between circuit nodes under electronic control. The MAX395 combines eight SPST switches with a serial control register, placing it in the hierarchy of analog switch, multiplexer or demultiplexer, interface IC, and semiconductor. It is useful where a microcontroller or test system must address multiple signal paths while minimizing the number of dedicated control pins. The device supports single-supply operation from 2.7 V to 16 V as well as dual-supply operation from ±2.7 V to ±8 V. Its maximum on-resistance is 100 ohm, and switching times are specified at up to 400 ns. Off leakage is 0.1 nA at +25°C and 5 nA at +85°C, helping preserve the integrity of high-impedance analog nodes during disconnected intervals. The internal serial interface shifts command data into the device on the rising edge of SCLK. Data presented at DIN is clocked into the internal shift register, where it controls the states of the eight SPST channels. According to the Analog Devices product page, the MAX395 is electrically equivalent to two MAX391 quad switches and is pin compatible with the MAX335. Typical uses include battery-powered measurement systems, automated test equipment, audio routing, industrial control interfaces, and general-purpose signal multiplexing. The serial interface reduces control-logic wiring, while the eight independently controlled channels provide flexible routing across a compact PCB footprint. Designers should account for the 100 ohm channel resistance when driving the switched nodes, especially with long PCB traces or high-frequency signals. Supply bypassing, grounded return paths, and careful routing of the serial clock and data lines are necessary to limit coupling into the analog channels. The power-up state leaves all switches off and resets the internal shift registers to zero. This page summarizes the device function, operating limits, pin-compatible family relationships, selection trade-offs, and practical integration guidance. It also organizes manufacturer information and technical alternatives to support faster component evaluation and board-level sourcing decisions.

RFQ যোগাযোগ
MAX396CPI+ - 16-Channel 100Ω Analog Multiplexer | Analog Devices
MAX396CPI+

MAX396CPI+ - 16-Channel 100Ω Analog Multiplexer | Analog Devices

The Analog Devices MAX396CPI+ is a precision 16-channel analog multiplexer with a 100Ω maximum on-resistance, 16:1 configuration, and a 28-pin PDIP package. It operates from a single +2.7V to +16V supply or from dual ±2.7V to ±8V supplies, making it suitable for low-voltage precision signal-routing systems. An analog multiplexer is an analog switch that connects one of several input signals to a shared output. A 16:1 device such as the MAX396CPI+ provides one common output and four binary address inputs for selecting among 16 channels. In the broader semiconductor hierarchy, it belongs to the analog switch and multiplexer family within interface integrated circuits. Its low-voltage CMOS implementation supports instrumentation, data acquisition, control, and test systems that route bipolar or single-ended signals. The MAX396 family provides maximum on-resistance of 100Ω, with resistance matching between switches maintained within 6Ω. The on-resistance remains flat within 10Ω over the specified signal range. Charge injection is limited to 5pC maximum, helping minimize switching transients in measurement paths. According to the manufacturer data sheet, the devices also provide electrostatic-discharge protection greater than 2000V using Method 3015.7. The device accepts either a single positive supply from +2.7V to +16V or dual supplies from ±2.7V to ±8V while retaining CMOS-compatible logic inputs. Switching timing is specified at 150ns, enabling the mux to serve both moderate-speed acquisition systems and precision measurement circuits. The MAX396 is offered in dual 8-channel configurations, while MAX396CPI+ is the 16-channel, 28-pin PDIP implementation. Typical uses include multiplexed sensor acquisition, programmable instrumentation, industrial control interfaces, automated test equipment, and low-level signal routing. The 100Ω on-resistance is particularly suitable for high-impedance sensors and amplifier inputs where insertion resistance must remain controlled. The low-voltage supply options also simplify systems using modern low-voltage analog and mixed-signal systems. PCB design should minimize trace resistance on muxed analog paths and keep switching-node capacitance low. Enable and address transitions should be sequenced so that unwanted channels do not connect during signal acquisition. The 28-pin PDIP footprint is also mechanically straightforward to prototype, although production designs must consider its through-hole package versus smaller surface-mount options. This page combines the manufacturer's electrical characteristics, packaging information, application guidance, pin-compatible comparisons, and practical layout considerations to support component selection and board-level implementation. It also identifies the operating limits and functional distinctions that matter when choosing between related MAX396 and MAX397 family members.

RFQ যোগাযোগ
MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices
MAX396EPI+

MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices

Analog Devices MAX396EPI+ is a precision, low-voltage CMOS analog multiplexer with one 16:1 switch, a maximum on-resistance of 100 ohms, and a 28-pin PDIP package. The device operates from a single +2.7 V to +16 V supply or from ±2.7 V to ±8 V dual supplies while maintaining compatibility with CMOS logic inputs. An analog multiplexer is an interface IC that connects multiple analog signal sources to a shared processing channel. The MAX396 belongs to the broader analog switch and multiplexer hierarchy, where switch resistance, channel matching, charge injection, leakage, and supply voltage determine how accurately a selected signal reaches the output. This makes the device suitable for precision measurement, data acquisition, test equipment, and industrial control systems. The MAX396EPI+ provides maximum on-resistance of 100 ohms, with on-resistance matching between switches maintained within 6 ohms. Its on-resistance remains flat over the specified signal range, with a maximum variation of 10 ohms. These characteristics make channel resistance less dependent on signal amplitude than in some multiplexers and support repeatable analog measurements. Charge injection is limited to 5 pC maximum. The low-voltage silicon-gate CMOS process supports low-power operation while providing fast switching. The multiplexer retains CMOS-logic input compatibility and includes electrostatic-discharge protection greater than 2,000 V per Method 3015.7. Single-supply operation supports +2.7 V to +16 V systems, while dual-supply operation permits bipolar signal ranges of ±2.7 V to ±8 V. Typical applications include multiplexed data acquisition, sensor signal routing, automated test systems, industrial measurement interfaces, and control systems that must connect several low-voltage analog inputs to one downstream converter or amplifier. Single-supply operation is convenient for compact equipment, whereas dual supplies allow the device to process signals around ground. When laying out a circuit, keep analog traces short and provide a stable ground reference. Place input and supply decoupling capacitors close to the device, and confirm that the selected signal amplitude, common-mode range, and switching frequency remain within the electrical limits of the application. This page organizes the key MAX396EPI+ specifications, pin-compatible replacement options, application guidance, and practical design considerations to support faster component selection and PCB implementation.

RFQ যোগাযোগ
MAX396EQI - 16:1 Precision CMOS Analog Multiplexer | Maxim
MAX396EQI

MAX396EQI - 16:1 Precision CMOS Analog Multiplexer | Maxim

The Maxim Integrated (Analog Devices) MAX396EQI is a precision 16-channel/dual 8-channel low-voltage CMOS analog multiplexer housed in a 28-pin PLCC (11.51 x 11.51 mm) package, specified over the industrial -40C to +85C temperature range. The device is built on Maxim's low-voltage CMOS process and integrates a single 16:1 mux (or two 8:1 muxes in parallel mode) with parallel address logic, making it a classic Maxim precision signal-routing building block. It is the original E-series (extended-industrial) part of the MAX396 family. What is an analog multiplexer? An analog multiplexer (mux) is a switch network that routes one of N analog input signals to a single output line under digital control. Muxes are the foundational building block of analog signal chains, sitting between sensors, test points, instrumentation amplifiers, and an ADC. The MAX396EQI specifically belongs to the CMOS analog mux family, characterized by low on-resistance, low leakage, and rail-to-rail analog signal handling - critical for instrumentation and data-acquisition front-ends. Key specifications include 100 ohm maximum on-resistance (matched within 6 ohm between channels), on-resistance flatness of 10 ohm maximum across the specified analog signal range, transition time under 250 ns, and input off-leakage current below 1 nA at +85C. These characteristics make the MAX396EQI well suited for low-distortion multiplexing of precision signals without the channel-mismatch errors that plague generic muxes. The device operates from a single +2.7V to +16V supply (or split +/- supplies), draws a low quiescent current, and provides ESD-rated inputs with TTL/CMOS-compatible address logic. Architecturally it uses charge-pump driven CMOS analog switches that keep the on-resistance flat over the analog signal range - a hallmark of Maxim's precision muxes versus competing JFET or DMOS parts. Typical applications include data-acquisition front-ends, automated test equipment (ATE) signal routing, audio signal routing, instrumentation multiplexing, and process-control analog input boards. Engineers typically pair the MAX396EQI with a precision op-amp buffer and a successive-approximation ADC to build a 16-channel low-noise analog front-end. When designing with the MAX396EQI, observe the absolute maximum analog signal range of V+ and V- rails; exceeding these destroys the switches. Use a low-ESR bypass capacitor of 0.1 uF close to the supply pin and reserve a small RC network on the address lines to suppress digital switching transients that couple into the analog path. Compared with modern pin-compatible successors, the MAX396EQI delivers superior channel matching but consumes more supply current and occupies a larger PLCC footprint than today's TSSOP muxes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not typically consolidated on the manufacturer datasheet, helping engineers select, source, and implement the MAX396EQI more confidently.

RFQ যোগাযোগ
MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated
MAX397CPI+

MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated

The Maxim Integrated MAX397CPI+ is a precision dual 8:1 CMOS analog multiplexer with a maximum on-resistance of 100 ohms, a 28-pin PDIP package, and support for single or dual supplies. The device provides 16 switch channels organized as two 8:1 muxes, with charge injection limited to 5 pC maximum and ESD protection greater than 2,000 V under Method 3015.7. An analog multiplexer is an analog switch network that routes a selected input channel to an output terminal under digital control. In the signal-chain hierarchy, the MAX397CPI+ is a CMOS analog switch IC, also described as a 16-channel or dual 8-channel precision multiplexer. It reduces the number of external connections required when several low-frequency analog signals must share one downstream converter, amplifier, or measurement circuit. The MAX397CPI+ uses Maxim's low-voltage silicon-gate process to provide low on-resistance, tightly matched switch resistance, low charge injection, and fast switching. Its maximum on-resistance is 100 ohms, with matching between switches specified within 6 ohms. The on-resistance remains flat within 10 ohms over the specified signal range, helping preserve signal amplitude and accuracy when different channels are selected. The multiplexer accepts a single supply from +2.7 V to +16 V or dual supplies from ±2.7 V to ±8 V. CMOS-compatible logic inputs simplify control from common digital systems. These supply options allow operation from low-voltage equipment as well as higher-range instrumentation while supporting bipolar signal paths when dual supplies are used. Typical uses include battery instrumentation, data acquisition, process monitoring, automated test equipment, and mixed-signal measurement systems. The two multiplexers can monitor paired or sequential sensor channels, select test points, or route instrumentation signals while limiting the number of external converter inputs. Design around the 100-ohm maximum on-resistance because it forms a signal-dependent voltage divider with the input and load impedances. Keep control traces away from analog inputs, use a low-impedance reference for digital controls, and observe the absolute maximum supply and signal voltages listed in the manufacturer datasheet. This page combines the device's documented electrical characteristics, package information, supply options, pin-compatible alternatives, and practical design guidance. It also organizes purchasing questions around the Request a Quote workflow on this page so engineers can evaluate supply and procurement without relying on static price information.

RFQ যোগাযোগ
MAX398CPE+ - 8:1 Precision Analog Multiplexer | Analog Devices
MAX398CPE+

MAX398CPE+ - 8:1 Precision Analog Multiplexer | Analog Devices

The Analog Devices MAX398CPE+ is a precision, single 8:1 CMOS analog multiplexer with on-resistance below 100 ohms, channel matching within 6 ohms, and a maximum on-resistance variation of 11 ohms across the specified analog signal range. It operates from 3 V to 15 V and is packaged in a 16-pin PDIP. An analog multiplexer is an integrated switching device that connects one common analog terminal to one of several channel terminals. In the broader semiconductor hierarchy, the MAX398 belongs to interface ICs, analog switches, multiplexers, and signal-routing semiconductors. Its 8:1 configuration allows eight analog inputs or outputs to share a common signal path, reducing component count in sample-and-hold systems, test equipment, signal routing, and embedded measurement circuits. The principal features include an 8:1 single-channel architecture, low on-resistance below 100 ohms, channel-to-channel matching within 6 ohms, and flat operation over the specified analog signal range. The MAX398CPE+ is manufactured in CMOS and accepts a 3 V to 15 V supply. Its PDIP package is suitable for through-hole assemblies, socketed legacy equipment, prototype boards, and systems where a rugged replaceable package is preferred over a surface-mount option. The multiplexer uses address-controlled selection to connect the common terminal to one of eight channels. Low and relatively consistent on-resistance helps limit signal attenuation as the selected channel changes, while the specified 11 ohm maximum variation supports predictable behavior across the analog range. These characteristics are particularly useful when the same acquisition or control circuitry handles multiple analog sources without redesigning the analog path for every input. Typical uses include sample-and-hold circuits, heads-up displays, guidance and control systems, military radios, battery-operated systems, PBX and PABX equipment, and audio signal routing. The 3 V to 15 V supply range supports both modern low-voltage systems and legacy industrial or communications equipment, although the complete signal range must remain compatible with the device's operating limits. Designers should place the multiplexer close to the source or destination of the analog signal to minimize PCB trace resistance and coupling. Address traces should be kept away from sensitive analog inputs, and unused control inputs should be driven to defined logic levels. Verify signal amplitude, supply voltage, and temperature against the manufacturer datasheet before substituting it into an existing assembly. This page combines the manufacturer's architecture information, package and multiplexing details, application references, pin-compatible alternatives, and practical design guidance to support component selection and replacement decisions beyond a basic distributor specification listing.

RFQ যোগাযোগ
MAX398ESE+ - 8:1 100Ω CMOS Analog Multiplexer | Analog Devices
MAX398ESE+

MAX398ESE+ - 8:1 100Ω CMOS Analog Multiplexer | Analog Devices

The Analog Devices MAX398ESE+ is a precision, single 8:1 CMOS analog multiplexer with 100 Ω on-resistance, a 3 V to 15 V supply range, and a 16-pin NSOIC package. The device routes one of eight analog inputs to a common output, making it suitable for precision signal-routing, data-acquisition, sample-and-hold, and automated-test systems. Its operating-temperature range is -40°C to +85°C for the MAX398ESE+ configuration. An analog multiplexer is a semiconductor switching device that connects multiple input channels to one shared output under digital control. It belongs to the analog switch and multiplexer hierarchy, which supports the broader field of interface ICs. By reducing the number of signal paths required on a circuit board, a multiplexed architecture can simplify wiring, conserve connector space, and support sequential acquisition from multiple sensors or test points. The MAX398 family provides precision channel matching and low on-resistance variation. According to the manufacturer product information, on-resistance is matched within 6 Ω between channels, while the maximum change across the specified analog signal range is 11 Ω. These characteristics help minimize gain error and distortion when signals pass through the selected channel. The device also uses low-voltage CMOS circuitry and supports dual 4-channel operation in appropriate device configurations. The MAX398ESE+ uses address and enable controls to select the active analog path. Its 8:1 organization allows one common output to be connected sequentially to eight source signals, reducing the number of analog switches required in multichannel systems. Signal integrity depends on keeping control traces short, using a stable low-impedance reference around the selected channel, and minimizing loading on the common output. Supply bypassing and grounding are especially important when low-level signals are measured. Typical uses include audio-signal routing, battery-powered acquisition systems, automated test equipment, communication equipment, guidance and control systems, heads-up displays, military radios, PBX and PABX systems, and sample-and-hold circuits. The precision matching is valuable in data-acquisition and test systems where channel-to-channel consistency directly affects calibration accuracy and measurement repeatability. Design the MAX398ESE+ with the required 3 V to 15 V operating range in mind and account for the voltage limits of every signal routed through the mux. Check the absolute maximum ratings and pin descriptions in the manufacturer datasheet before applying signals, especially when the analog input can exceed the selected supply rail. This page combines the device architecture, operating limits, pin-level routing guidance, application analysis, and same-package replacement information to support faster component selection and PCB-level replacement decisions.

RFQ যোগাযোগ