Maxim Integrated

MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim

MPN: MAX355CWE+ ✓ সক্রিয়
4.5 V to 36 V Vdss 500 pA maximum Id 350 ohm maximum Rds(on) 16-SOIC, 7.50 mm width Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MAX355CWE+ সারাংশ

The Maxim Integrated MAX355CWE+ is a dual 4:1 fault-protected analog multiplexer with two independently controlled 4:1 switches, 350 ohm on-resistance, and a 16-pin WSOIC package. Its 4.5 V to 36 V operating supply range and protection against overvoltage up to 40 V beyond the supply rails make it suitable for routing signals through systems where input pins may temporarily exceed the normal supply limits during power-up, power-down, or fault conditions.

An analog multiplexer is a switching interface that connects one signal source to one of several destinations. In this case, each MAX355CWE+ channel implements a 4:1 configuration, allowing two multiplexers to route four sources per channel. Within the broader semiconductor hierarchy, the MAX355CWE+ is an analog switch IC, then a multiplexer, then an interface IC used to connect external signals to analog processing circuitry.

Key electrical characteristics include a maximum on-resistance of 350 ohms, maximum off leakage of 500 pA, and crosstalk of -92 dB at 100 kHz. The 350 ohm resistance is suitable for moderate-impedance sensor, measurement, and control paths rather than high-bandwidth, low-impedance video networks. Fault protection extends to 40 V beyond the supply rails, helping isolate sensitive downstream circuitry during abnormal input conditions.

The device uses a series N-channel, P-channel, and N-channel switching structure to provide fault protection. Its dual-mux architecture makes it useful where multiple analog inputs must be selected under software or hardware control. Control inputs allow the selected paths to be changed without mechanical switching, making the MAX355CWE+ appropriate for test systems, industrial controls, data acquisition modules, and instrumentation.

Typical uses include battery-powered monitoring equipment, industrial sensor interfaces, laboratory measurement systems, and analog test equipment. The 4.5 V minimum supply supports systems operating from a 5 V rail, while the 36 V maximum expands applicability to higher-voltage industrial environments. Protection is especially relevant where an external cable or sensor may present an overvoltage before system power stabilizes.

Designers should verify the input and output voltage limits against the specific fault condition and avoid treating the 40 V protection rating as a continuous operating rating. Keep analog routing paths away from high-current switching nodes, provide a stable bypass capacitor near the supply pins, and use high-impedance sensing circuits to reduce errors caused by the 350 ohm on-resistance.

This page combines the MAX355CWE+ electrical characteristics, application guidance, package information, and verified drop-in alternatives to support faster component selection and PCB replacement decisions.

এর জন্য ড্রপ-ইন বিকল্প MAX355CWE+ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible MAX355CWE+ (একই form factor এবং footprint) — পার্থক্য রয়েছে Multiplexer Configuration, On-Resistance, Package.

Maxim Integrated
Multiplexer Configuration: Dual 4:1 analog multiplexer
On-Resistance: 350 ohm
Package: 16-pin WSOIC, 7.62 mm body
এর সাথে তুলনা করুন MAX355CWE+ →

MAX355CWE

✅ ড্রপ-ইন
📦 16-SOIC
Same dual 4:1 configuration, 350 ohm maximum on-resistance, and 16-SOIC footprint; MAX355CWE lacks the plus suffix associated with the lead-free ordering option.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX355EWE+

✅ ড্রপ-ইন
Maxim Integrated
📦 16-SOIC
Dual 4:1 analog multiplexer · 2 circuits · 8 channels total · SP4T · 350 ohm · 4.5 V to 36 V · Up to 40 V beyond supply rails · Series N-channel, P-channel, N-channel structure

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MAX355CWE+ বিশেষণ

Multiplexer Configuration Dual 4:1
Number of Circuits 2 circuits
On-Resistance 350 ohm maximum
Supply Voltage Range 4.5 V to 36 V
Overvoltage Protection Up to 40 V beyond supply rails
Off Leakage Current 500 pA maximum
Crosstalk -92 dB at 100 kHz
অপারেটিং তাপমাত্রা 0°C to 70°C
প্যাকেজ 16-SOIC, 7.50 mm width
Package Type WSOIC-16
মাউন্টিং টাইপ Surface mount
Switch Structure Series N-channel, P-channel, N-channel
Fault Protection Protected during power-up, power-down, and fault conditions
Lead-Free Finish Yes for MAX355CWE+ ordering suffix

MAX355CWE+ wsoic-16 পিন কনফিগারেশন গাইড

MAX355CWE+ (wsoic-16 প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

MAX355CWE+-এর জন্য wsoic-16 প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX355CWE+.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MAX355CWE+ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Multiplexing, Data Acquisition Modules, Automated Test Equipment, Battery-Powered Monitoring Equipment, Laboratory Measurement Systems, High-Voltage Control Interfaces.

🏭

Industrial Sensor Multiplexing

The MAX355CWE+ fits industrial sensor interfaces that require several measured signals to share a limited analog front end. Each of its two independent 4:1 sections can connect one of four inputs to a common terminal, reducing the number of analog routing components needed. The 4.5 V to 36 V supply range supports both 5 V instrumentation and higher-voltage industrial rails, while protection up to 40 V beyond the supply rails helps manage transient faults. Because on-resistance reaches 350 ohm, the selected sensor impedance and allowable measurement error must be included in the signal-chain design.

📊

Data Acquisition Modules

A dual 4:1 analog multiplexer is useful in compact data-acquisition modules where several inputs must be routed to a shared converter or measurement amplifier. The MAX355CWE+ provides two selectable four-input groups in one 16-WSOIC package, simplifying control logic and conserving board area. Its maximum off leakage of 500 pA and -92 dB crosstalk at 100 kHz help preserve signal integrity between channels, although the 350 ohm switch resistance should be compensated when the source impedance is finite. The 4.5 V minimum supply also supports conventional 5 V acquisition systems.

🖥️

Automated Test Equipment

The MAX355CWE+ can route test signals among multiple sources in automated test equipment while providing fault isolation during startup or abnormal fixture conditions. Two 4:1 sections allow compact control of several test paths without requiring a separate switch for every channel. The maximum on-resistance of 350 ohm is generally appropriate for high-impedance test fixtures, and the -92 dB crosstalk specification at 100 kHz supports low-level signal measurements. Designers should still account for switch resistance, leakage, and settling time in the measurement accuracy budget.

📱

Battery-Powered Monitoring Equipment

The MAX355CWE+ is suitable for battery-powered monitoring equipment that multiplexes sensor inputs while operating from a regulated 5 V system. Its dual 4:1 organization reduces wiring and component count in portable instruments, and fault protection helps prevent external sensor lines from exposing downstream circuitry to startup or shutdown overvoltage. The 4.5 V minimum supply fits a 5 V rail, while the 350 ohm maximum on-resistance is best matched to high-impedance sensors. Confirm that injected channel error remains acceptable at the lowest expected source impedance.

🔬

Laboratory Measurement Systems

Laboratory measurement systems can use the MAX355CWE+ to select among four input paths in each of two switch sections. The -92 dB crosstalk at 100 kHz and 500 pA maximum off leakage help maintain channel separation for precision measurements, while the 4:1 topology supports compact instrument front ends. The 350 ohm on-resistance is the primary accuracy consideration when driving amplifier inputs with finite impedance. Keep the routing traces short, maintain a quiet ground reference, and compare the complete measurement uncertainty against the selected switch resistance.

⚡

High-Voltage Control Interfaces

The MAX355CWE+ can interface control signals in systems operating across a broad supply range, including industrial 24 V and 36 V applications. Its 4.5 V to 36 V operating specification supports higher-voltage logic environments, and the fault-protected series N-channel, P-channel, and N-channel structure limits fault exposure beyond the normal rails. When switching external control lines, verify the absolute maximum input and output ratings, ensure the selected switch path does not exceed them, and provide local supply bypassing to maintain stable operation.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

MAX355CWE Same-family non-plus ordering option ব্যবহৃত হয়: Industrial Sensor Multiplexing, Data Acquisition Modules, Automated Test Equipment, Battery-Powered Monitoring Equipment, Laboratory Measurement Systems, High-Voltage Control Interfaces MAX355EWE+ Maxim Integrated ব্যবহৃত হয়: Industrial Sensor Multiplexing, Data Acquisition Modules, Automated Test Equipment, Battery-Powered Monitoring Equipment, Laboratory Measurement Systems, High-Voltage Control Interfaces
What is the MAX355CWE+?
The MAX355CWE+ is a dual 4:1 fault-protected analog multiplexer from Maxim Integrated. It contains two independent 4:1 analog switches, has a maximum on-resistance of 350 ohms, operates from 4.5 V to 36 V, and is packaged in a 16-pin WSOIC. According to the manufacturer product page, the MAX355 family is in production and uses fault-protection circuitry to withstand overvoltage up to 40 V beyond the supply rails.
What is the operating voltage of MAX355CWE+?
The MAX355CWE+ operates from 4.5 V to 36 V. The manufacturer documentation identifies the MAX355 as a production fault-protected analog multiplexer, while product listings specify a 4.5 V to 36 V operating range for the 16-SOIC device. Its 36 V upper limit makes it suitable for 5 V instrumentation and higher-voltage industrial systems, provided signal amplitudes remain within the applicable input limits.
What is the on-resistance of MAX355CWE+?
The MAX355CWE+ has a maximum on-resistance of 350 ohms, as stated in its manufacturer specifications and distributor product records. This figure applies when a selected analog path is conducting. It is suitable for high-impedance sensors, test inputs, and instrumentation signals, but it can create measurable voltage errors when driving substantially lower-impedance networks.
How much overvoltage can the MAX355CWE+ withstand?
The MAX355 family can protect against overvoltage up to 40 V beyond the supply rails during power-up, power-down, and fault conditions. According to the manufacturer product page, its series N-channel, P-channel, and N-channel structure performs this protection function. This rating concerns fault events and should not be interpreted as permission to apply 40 V beyond the rails continuously.
Where can I download the MAX355CWE+ datasheet PDF?
The MAX355CWE+ datasheet and product resources are available through the Analog Devices MAX355 product page at https://www.analog.com/en/products/max355.html. Use the manufacturer datasheet to confirm the complete pin configuration, absolute maximum ratings, electrical characteristics, control truth table, and recommended operating conditions before placing a component in a production design.
Where can I find the MAX355CWE+ pinout?
The MAX355CWE+ uses a 16-pin WSOIC package, and its complete pin assignment appears in the manufacturer MAX355 datasheet. Use the pin-description table and package drawing for connections to A0/A1, S0/S1, common terminals, supply, and ground. Do not infer pin functions from a generic SOIC diagram because numbering and signal assignments are specific to the MAX355 family.
Is MAX355CWE+ suitable for industrial sensor multiplexing?
The MAX355CWE+ is suitable for many industrial sensor-multiplexing applications because it supports a 4.5 V to 36 V supply range, provides two 4:1 switch sections, and includes fault protection up to 40 V beyond the supply rails. The 350 ohm maximum on-resistance should be checked against the sensor output impedance and required accuracy. For precision measurements, include switch resistance and leakage in the complete error budget.
What is the difference between MAX355CWE+ and MAX355EWE+?
The principal difference is the operating-temperature grade: MAX355CWE+ is specified from 0°C to 70°C, while MAX355EWE+ is specified from -40°C to 85°C. Both use a 16-SOIC package and belong to the same MAX355 family. The MAX355EWE+ is therefore the better choice when the board must operate below 0°C or above 70°C, provided its operating range is acceptable.
Can MAX355EWE+ replace MAX355CWE+?
The MAX355EWE+ can be considered for a MAX355CWE+ replacement when the original circuit stays within 0°C to 70°C and the PCB accepts the 16-SOIC footprint. The MAX355EWE+ expands the rated temperature range to -40°C to 85°C while retaining the same family architecture. Confirm pin assignments, control logic, absolute maximum ratings, and production availability against the manufacturer datasheet before approving the substitution.
What is the best drop-in replacement for MAX355CWE+?
The closest verified drop-in choice is the MAX355CWE without the plus suffix, which retains the same dual 4:1 configuration, 350 ohm on-resistance, 16-SOIC package, and core electrical function. The MAX355EWE+ is another same-package option when its -40°C to 85°C rating is preferable. Use the Request a Quote form on this page for current availability of exact MPNs and verified replacements.
When should I choose MAX355CWE+ over MAX355EWE+?
Choose MAX355CWE+ when the assembly is guaranteed to remain within 0°C to 70°C and the lead-free ordering suffix suits the procurement plan. Choose MAX355EWE+ when extended-temperature operation from -40°C to 85°C is required. Both devices use the same 16-SOIC package and support two 4:1 analog switch sections, so the temperature requirement is normally the principal selection criterion.
Is MAX355CWE+ suitable for 5 V test and measurement equipment?
The MAX355CWE+ is suitable for many 5 V test and measurement systems because its minimum operating voltage is 4.5 V and it provides two 4:1 analog multiplexing sections. The 350 ohm maximum on-resistance and -92 dB crosstalk at 100 kHz should be evaluated against the measurement bandwidth and source impedance. Use short analog traces and a stable supply bypass capacitor to minimize added noise and settling error.
What can replace MAX355CWE+?
Verified same-family replacements include the MAX355CWE and MAX355EWE+, both in a 16-SOIC package. The MAX355CWE preserves the target’s core electrical configuration, while the MAX355EWE+ provides a wider -40°C to 85°C operating range. No verified cross-brand, pin-compatible alternative was identified, so production substitution should focus on these same-family options until a candidate is independently validated.
What are the key specifications of MAX355CWE+ that engineers should know?
The principal MAX355CWE+ specifications are dual 4:1 multiplexing, two switch circuits, 350 ohm maximum on-resistance, 4.5 V to 36 V operation, 500 pA maximum off leakage, -92 dB crosstalk at 100 kHz, and a 16-WSOIC package. Fault protection reaches up to 40 V beyond the supply rails during startup, shutdown, and abnormal conditions. These characteristics position it for high-impedance industrial and instrumentation signals rather than low-impedance high-speed video paths.
Where to buy MAX355CWE+ online and what is the lead time?
Use the Request a Quote form on this page to request the current price, stock status, minimum order quantity, and lead time for MAX355CWE+. The part is identified as a production MAX355 family device by the manufacturer, but current commercial terms can vary with order quantity and packaging. The form avoids static quotations and provides the purchasing details needed for a current production decision.
What is the price of MAX355CWE+?
The current commercial price for MAX355CWE+ is obtained through the Request a Quote form on this page. Pricing can change with quantity, package, and market conditions, so a static price should not be used for budgeting. Submit the required MPN, quantity, and delivery details through the quote form to obtain current availability, lead time, and ordering terms.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX355CWE+ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose MAX355CWE+ for a dual 4:1 analog multiplexer in a 16-SOIC design that operates from 4.5 V to 36 V and remains within 0°C to 70°C. Its 350 ohm maximum on-resistance is most appropriate for high-impedance sensor, instrumentation, and test paths, while fault protection up to 40 V beyond the rails adds resilience during startup, shutdown, and abnormal input conditions. Choose MAX355CWE when the exact core MAX355 function is needed without the plus ordering suffix. Choose MAX355EWE+ when the assembly requires the wider -40°C to 85°C temperature range while retaining the same package and family architecture. For a cross-brand substitution, require evidence of identical pinout, control logic, on-resistance, leakage, supply range, absolute maximum ratings, and fault behavior; a package match alone is not sufficient.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MAX355CWE MAX355EWE+
Package 16-SOIC 16-SOIC 16-SOIC
Brand Maxim Integrated Maxim Integrated Maxim Integrated
Multiplexer Configuration Dual 4:1 Dual 4:1 Dual 4:1
Number of Circuits 2 circuits 2 circuits 2 circuits
On-Resistance 350 ohm maximum 350 ohm maximum 350 ohm maximum
Supply Voltage Range 4.5 V to 36 V 4.5 V to 36 V 4.5 V to 36 V
Off Leakage Current 500 pA maximum 500 pA maximum 500 pA maximum
Crosstalk -92 dB at 100 kHz -92 dB at 100 kHz -92 dB at 100 kHz
Operating Temperature 0°C to 70°C 0°C to 70°C -40°C to 85°C
Overvoltage Protection Up to 40 V beyond supply rails Up to 40 V beyond supply rails Up to 40 V beyond supply rails

মূল পার্থক্যসমূহ

  • Combines two protected 4:1 multiplexers in one package (বনামMAX355CWE)
  • Maintains the same protected analog-switch architecture for exact-family replacement (বনামMAX355EWE+)
  • Commercial grade supports a 0°C to 70°C operating range (বনামMAX355EWE+)

ডিজাইন নোট

Treat the 350 ohm maximum on-resistance as part of the signal-path impedance rather than as an ideal switch resistance. For a divider formed by this resistance and the receiving input impedance, the resulting error can be significant when the input impedance is only tens of kilohms. Use a high-impedance receiver or amplifier input, and include channel resistance and leakage in the measurement uncertainty calculation.

Place the supply bypass capacitor close to the device supply and ground pins, and keep analog switch traces short and separated from switching-current paths. The dual 4:1 topology can place sensitive signals near control or routed channels, so route the two groups with attention to crosstalk and ground return paths. A continuous ground reference under the device helps reduce coupling into the high-impedance measurement paths.

Do not confuse fault protection with a continuous overvoltage rating. The MAX355 family protects against overvoltage up to 40 V beyond the supply rails during power-up, power-down, and fault conditions, but normal operating voltages and absolute maximum ratings must still be respected. Also confirm the selected control logic and pin functions against the manufacturer datasheet rather than assigning control signals from generic multiplexer conventions.

Reserve the same 16-SOIC land pattern when evaluating MAX355CWE and MAX355EWE+ replacements. Verify body width, lead pitch, and pin orientation on the PCB rather than relying only on the generic package name. The two identified replacements use the same family architecture, but production qualification should still include control-state timing, temperature behavior, and the worst-case analog accuracy at the required source impedance.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Yes
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The plus suffix identifies the lead-free ordering option. No explicit RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 statement was included in the cited product records.

ডেটা যাচাই করা হয়েছে: 2026-11-14 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MAX355CWE+ datasheet MAX355CWE+ pinout MAX355CWE+ datasheet pdf MAX355CWE+ equivalent MAX355CWE+ replacement MAX355CWE+ cross reference MAX355CWE+ vs MAX355EWE+ MAX355CWE+ 16-SOIC footprint MAX355CWE+ application circuit MAX355CWE+ price MAX355CWE+ stock Maxim Integrated MAX355CWE+ dual 4:1 350 ohm multiplexer IC 4.5V to 36V fault protected mux

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Maxim Integrated Analog Devices MAX355CWE+ MAX355CWE MAX355EWE+ MAX355 analog multiplexer analog switch IC interface IC multiplexer semiconductor dual 4:1 configuration on-resistance off leakage crosstalk fault protection overvoltage protection WSOIC-16 16-SOIC surface mount industrial instrumentation data acquisition test and measurement N-channel P-channel
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন