Analog Devices

AD96687BQ - 2.5 ns Dual Ultrafast ECL Comparator | Analog Devices

MPN: AD96687BQ ✗ জীবনকালের সমাপ্তি
16-pin CERDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

AD96687BQ সারাংশ

The Analog Devices AD96687BQ is an ultrafast dual voltage comparator with 2.5 ns propagation delay, 50 ps propagation-delay dispersion, complementary outputs, and an open-emitter ECL output stage in a 16-pin CERDIP package. The AD96687BQ is marked not recommended for new designs, so it is best suited to maintenance, repair, and qualified legacy systems rather than new product development.

A high-speed comparator is a semiconductor component that determines whether an input voltage is above or below a reference threshold and then produces a corresponding logic output. The AD96687 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Its dual-channel architecture allows two independent threshold decisions, while its ECL output structure supports high-speed digital signaling in communications, clock, test, and data-conversion systems.

The principal performance characteristics are the 2.5 ns propagation delay, 50 ps propagation-delay dispersion, dual-comparator configuration, latch capability, and complementary open-emitter outputs. Propagation delay describes the time between a comparator input transition and the corresponding output response. Propagation-delay dispersion measures how that delay changes with overdrive, making the 50 ps figure useful when assessing decision timing under different input overdrive conditions.

The AD96687BQ is identified as a 16-pin CERDIP device and uses an ECL output interface with complementary outputs and open-emitter termination. Open-emitter outputs permit wired-connection and termination techniques commonly used in high-speed logic systems. Exact input-common-mode limits, supply requirements, input offset voltage, input capacitance, output levels, and operating-temperature limits must be confirmed in the Analog Devices data sheet before schematic capture or replacement qualification.

Typical uses include high-speed clock recovery, pulse-width qualification, threshold detection, telecom line-interface timing, data-conversion support, and legacy instrumentation. The 2.5 ns delay is the main reason to select this device over slower general-purpose comparators. Open-emitter outputs also make it useful where several outputs must share a common termination or pull-up arrangement, provided the board-level timing and logic-level design is verified carefully.

The primary design caution is board-level signal integrity. A 2.5 ns device leaves little timing margin for long traces, excessive loading, poorly terminated interconnects, or slow output rise and fall times. Keep interconnect paths short, use the recommended termination scheme, provide a low-impedance return path, and validate source and termination compatibility with an oscilloscope or high-speed simulation.

This product record combines manufacturer device information with practical comparisons, replacement criteria, and design guidance. Because the AD96687BQ is not recommended for new designs and no manufacturer-sanctioned drop-in replacement is identified, engineers should first confirm lifecycle requirements, exact pin compatibility, output logic, supply rails, and timing specifications before approving any substitute for an existing AD96687BQ design.

এর জন্য ড্রপ-ইন বিকল্প AD96687BQ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।

বিকল্প অনুরোধ করুন

AD96687BQ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Comparator Type Dual voltage comparator with latch
Number of Channels 2 channels
Propagation Delay 2.5 ns
Propagation Delay Dispersion 50 ps
আউটপুট কনফিগারেশন Complementary
Output Logic ECL
আউটপুট টাইপ Open-emitter
Latch Capability Yes
প্যাকেজ 16-pin CERDIP
পিনের সংখ্যা 16 pins
Lifecycle Recommendation Not recommended for new designs

AD96687BQ 16-pin cerdip পিন কনফিগারেশন গাইড

AD96687BQ (16-pin cerdip প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

AD96687BQ-এর জন্য 16-pin cerdip প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি AD96687BQ.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

AD96687BQ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: High-Speed Clock Qualification, Pulse-Width Detection, Telecom Line-Interface Timing, Data-Conversion Support, Industrial Control and Instrumentation, Legacy Test Equipment Repair.

⚡

High-Speed Clock Qualification

The AD96687BQ is appropriate for legacy clock-qualification circuits that require a rapid threshold decision and two complementary logic outputs. Its 2.5 ns propagation delay leaves only a short interval between an input transition and the corresponding output response, while the 50 ps propagation-delay dispersion provides a defined measure of delay variation with overdrive. The device can compare a clock or pulse against a threshold and generate complementary status signals for downstream timing logic. Because its open-emitter ECL outputs require deliberate termination, the board should use short routes, a continuous ground reference, and the interface arrangement specified by Analog Devices. The part is best treated as a maintenance component because it is not recommended for new designs.

🖥️

Pulse-Width Detection

The AD96687BQ can support pulse-width or timing-window detection in legacy high-speed systems by comparing a pulse-derived voltage with a threshold and producing complementary ECL outputs. The dual-channel configuration permits two threshold relationships to be evaluated within one package, and the 2.5 ns propagation delay helps limit the comparator-added portion of the response time. The 50 ps dispersion figure is important when the design evaluates delay variation under different overdrive levels. Open-emitter outputs allow the two channels to be interfaced with an appropriate common termination arrangement. Exact input switching thresholds and common-mode limits must be established from the manufacturer data sheet before defining pulse timing tolerances.

🌐

Telecom Line-Interface Timing

The AD96687BQ is relevant to maintenance of legacy telecom equipment that uses complementary ECL outputs for high-speed threshold decisions. Its 2.5 ns propagation delay and dual-channel architecture are well aligned with receiver timing and pulse-detection functions, while the open-emitter output structure supports conventional ECL wiring practices. A replacement design must preserve the established termination voltage, line loading, and logic polarity. PCB routing should minimize trace length and provide an uninterrupted ground reference because transmission-line effects can consume the timing margin more quickly than the nominal comparator delay. Since the family is not recommended for new designs, new telecom platforms should use a currently supported comparator unless legacy compatibility makes continued AD96687BQ use necessary.

📺

Data-Conversion Support

The AD96687BQ can serve as a fast threshold detector around high-speed data-conversion and digitization systems, particularly when an existing design uses ECL-compatible signaling. Its 2.5 ns propagation delay allows the comparator stage to respond quickly to an analog crossing, and the dual configuration can monitor two independent thresholds or provide complementary status indications. The 50 ps propagation-delay dispersion should be included in timing analysis because it describes delay changes with overdrive. Analog input conditioning, reference accuracy, and routing remain system-level responsibilities. The legacy CERDIP package and not-for-new-designs status make AD96687BQ most appropriate for maintaining an established converter or clocking subsystem rather than starting an unrestricted new design.

🏭

Industrial Control and Instrumentation

In established industrial control and test-instrumentation equipment, the AD96687BQ can provide fast limit detection for analog signals that require complementary threshold outputs. The dual channels can monitor two limits, generate an over-range indication, or create complementary logic states for a downstream controller. The 2.5 ns propagation delay is useful for minimizing comparator contribution in short measurement windows, while the 50 ps dispersion figure helps characterize behavior across different overdrive conditions. The ECL open-emitter interface must match the existing system logic and termination strategy. Engineers should also account for the input network, reference stability, grounding, and any isolation barriers before treating the comparator as the sole protection mechanism.

🔧

Legacy Test Equipment Repair

The AD96687BQ is particularly useful for repairing legacy oscilloscope, logic-analyzer, pulse-generator, and automated test equipment that originally used this dual ultrafast ECL comparator. A 2.5 ns propagation delay can preserve the intended behavior of fast threshold and trigger paths, while the dual configuration avoids replacing the function with two separate single-channel packages when footprint constraints exist. Exact replacement requires verification of the 16-pin CERDIP pinout, latch behavior, output polarity, supply requirements, common-mode range, and temperature grade. Inspect the ceramic package for damage and verify continuity before installation. For assets that must remain serviceable for many years, stock planning should reflect the device's not-recommended-for-new-designs lifecycle status.

What is the AD96687BQ and what are its key specifications?
The AD96687BQ is a dual ultrafast voltage comparator with 2.5 ns propagation delay, 50 ps propagation-delay dispersion, complementary ECL outputs, and a 16-pin CERDIP package. Analog Devices describes the AD96687 as an equally fast dual counterpart to the AD96685 single comparator. Its open-emitter outputs and latch capability make it suitable for high-speed timing, pulse-qualification, and legacy ECL interface designs. According to the Analog Devices product page and Data Sheet, Rev. D, these are the principal reasons the device remains relevant for maintenance of established equipment.
Is the AD96687BQ suitable for new designs?
The AD96687BQ is not recommended for new designs because Analog Devices marks the AD96687 family NOT RECOMMENDED FOR NEW DESIGNS. It remains appropriate for repairing or maintaining systems in which the part is already qualified. For a new high-speed comparator design, evaluate an active device whose lifecycle status supports new development. If a legacy design must retain the AD96687BQ, verify operating-temperature grade, supply requirements, pinout, and timing against the Analog Devices Data Sheet, Rev. D before releasing the circuit for production.
Where can I download the AD96687BQ datasheet PDF?
The official AD96687BQ documentation is available from the Analog Devices AD96687 product page at https://www.analog.com/en/products/ad96687.html. The product materials identify the data sheet as Rev. D and provide the device description, selection table, documentation, and ordering information. Use the manufacturer data sheet rather than an automatically generated mirror when defining the circuit. The pin-description table, recommended operating conditions, supply rails, and timing limits should be checked directly before using AD96687BQ in a replacement or revision.
Where can I find the AD96687BQ pinout?
The AD96687BQ pinout should be taken from the pin-description table in the Analog Devices AD96687 Data Sheet, Rev. D, accessed through the official AD96687 product page. AD96687BQ is identified as a 16-pin CERDIP device, but that package description alone does not establish the function of every terminal. Use the package drawing and pin table together to confirm input polarity, latch-control connections, supply pins, complementary outputs, and exposed connections before assigning a PCB footprint.
What does the 2.5 ns propagation delay of AD96687BQ mean?
The 2.5 ns propagation delay is the interval between a comparator input transition and the corresponding output response under the conditions specified by Analog Devices. This very short delay allows the AD96687BQ to make timing decisions much faster than conventional slow comparators. The related 50 ps propagation-delay dispersion indicates how much response timing can change with different overdrive conditions. System timing budgets should include comparator delay, output transition time, interconnect delay, receiver setup time, and any external termination effects.
How do AD96687BQ and AD96685 differ?
The AD96687BQ is a dual comparator, while the AD96685 is a single comparator; both are identified by Analog Devices as ultrafast devices with 2.5 ns propagation delay. The AD96687 therefore provides two comparator channels in one package and offers complementary, open-emitter ECL outputs with latch capability. The AD96685 is not a pin-for-pin substitute for the dual AD96687BQ. Choose between them according to channel count and package requirements rather than treating the single comparator as a drop-in replacement.
When should I choose AD96687BQ instead of a single-channel high-speed comparator?
Choose AD96687BQ when the circuit requires two independent high-speed threshold decisions and the surrounding logic is compatible with complementary ECL outputs, open-emitter termination, and the 16-pin CERDIP package. Its 2.5 ns propagation delay and 50 ps dispersion make it useful when timing margin is important. Select a single-channel device instead when only one decision path is required. Either way, verify the complete input, supply, latch, output, and timing specifications in the manufacturer data sheet.
What is the best drop-in replacement for AD96687BQ?
No manufacturer-sanctioned drop-in replacement for AD96687BQ is identified. A valid replacement must match the 16-pin CERDIP footprint and pin functions, provide complementary open-emitter ECL outputs, support the required latch operation, and meet the original supply, common-mode, timing, and temperature requirements. The AD96685 is a single-channel family member and therefore is not a drop-in replacement. Before substituting any part, compare the manufacturer pinout and timing tables and validate the complete interface in hardware.
Can a cross-brand comparator replace AD96687BQ without PCB changes?
A cross-brand comparator should not be treated as a drop-in replacement unless its documentation proves the same 16-pin CERDIP footprint, identical pin assignments, compatible ECL output structure, latch behavior, supply rails, input common-mode range, and timing performance. The available cross-reference information does not identify a qualified cross-brand equivalent for AD96687BQ. For an installed or safety-relevant system, use a component specifically qualified by its manufacturer or obtain explicit engineering approval after laboratory verification.
What can replace AD96687BQ in a legacy design?
Only a part with verified pin compatibility and equivalent electrical behavior should replace AD96687BQ in a legacy design. Search requirements include the 16-pin CERDIP package, complementary open-emitter ECL outputs, latch behavior, 2.5 ns-class timing, and the original supply and common-mode conditions. Packaging-code variants of AD96687BQ may differ in temperature grade or orderable form and must be checked rather than assumed interchangeable. If qualification data is unavailable, retain the originally qualified device.
Where can I request a quote for AD96687BQ?
Use the Request a Quote form on this page to request current AD96687BQ availability, lead time, and order handling. Because the device is marked not recommended for new designs, availability can depend on remaining manufacturer or channel inventory rather than current production. Provide the exact AD96687BQ suffix, required quantity, and any target temperature grade when requesting the quote. Do not assume that a similarly named AD96687 ordering code has the same grade, package, or lifecycle status.
What is the price of AD96687BQ?
Current pricing for AD96687BQ should be requested through the Request a Quote form on this page because availability and lifecycle conditions can change for a device not recommended for new designs. The quote request should state the exact AD96687BQ MPN and quantity. Engineers should also confirm the condition, inspectability, and traceability of legacy ceramic packages before authorizing procurement, since different channels may represent new, unused, or previously handled stock differently.
What is the lead time and stock status for AD96687BQ?
Current stock and lead time for AD96687BQ should be confirmed through the Request a Quote form on this page. Analog Devices marks the AD96687 family as not recommended for new designs, so an order commitment should not be based on the general active-part expectations applied to current production ICs. State the required quantity, acceptable date code, inspection requirements, and target date in the request. For long-life maintenance programs, consider periodic inventory planning because continuity may depend on remaining legacy stock.
How should open-emitter ECL outputs be terminated for AD96687BQ?
The AD96687BQ outputs are complementary open-emitter ECL outputs, so termination must match the output structure and the logic architecture. Use the pull-up or termination arrangement specified by Analog Devices for the intended ECL interface rather than treating the outputs like conventional push-pull CMOS outputs. Keep traces short, provide a continuous ground reference, and verify the termination voltage and current requirements. Board-level behavior should be checked because external resistance, loading, and interconnect geometry affect both edge rate and timing margin.
What PCB layout practices are important for a 2.5 ns AD96687BQ comparator?
Use short comparator traces, a continuous return plane, and the manufacturer-recommended output termination for a 2.5 ns AD96687BQ design. Avoid long stubs and unnecessary test-point branches on timing-critical nets, and place any required bypass or termination components close to their associated pins. Validate rise and fall times, ringing, and decision-point timing at the receiver with a suitable high-bandwidth oscilloscope. The small device delay does not compensate for excessive interconnect delay or poor return-path continuity.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা AD96687BQ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose AD96687BQ when maintaining an established 16-pin CERDIP design that requires two high-speed threshold channels, complementary open-emitter ECL outputs, and approximately 2.5 ns propagation delay. Its 50 ps propagation-delay dispersion makes it useful where overdrive-dependent timing must be characterized. The AD96685 is appropriate only when a single comparator is required; it is not a drop-in substitute for the dual AD96687BQ. No cross-brand drop-in alternative has been established from the available documentation, so procurement should focus on exact suffix and condition verification. For new designs, favor a currently supported high-speed comparator with a documented pinout, termination arrangement, and timing distribution. For legacy repair, confirm the original device’s latch behavior, supply rails, common-mode range, output polarity, and temperature grade before installation.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য
Package 16-pin CERDIP
Brand Analog Devices
Comparator Channels 2 channels
Propagation Delay 2.5 ns
Propagation Delay Dispersion 50 ps
Output Logic ECL
Output Configuration Complementary open-emitter
Latch Capability Yes
Lifecycle Recommendation Not recommended for new designs

মূল পার্থক্যসমূহ

  • Dual-channel packaging (বনামAD96685)
  • Complementary open-emitter ECL output interface (বনামAD96685)
  • Defined high-speed timing characteristics (বনামAD96685)

ডিজাইন নোট

Treat the open-emitter ECL outputs as a high-speed transmission-line interface. Use the termination arrangement specified by Analog Devices, keep traces short, provide a continuous ground reference, and avoid unnecessary stubs or long test-point branches. Validate edge rate, ringing, and receiver setup margin at the logic device rather than relying only on the 2.5 ns nominal propagation delay.

Keep comparator inputs, latch-control connections, and supply decoupling paths compact. Place required termination and bypass components close to their associated pins, and maintain the standard pin-order definition of the 16-pin CERDIP footprint. Verify the physical package drawing because pin numbering and terminal functions must be taken directly from the manufacturer data sheet.

Do not assume that a similarly named AD96687 ordering code is automatically interchangeable. Packaging suffixes may identify different temperature grades, package constructions, or orderable forms. Confirm the exact suffix, operating-temperature grade, lifecycle status, pinout, latch behavior, ECL output configuration, supply rails, and common-mode range before approving a replacement.

Use the maximum expected ambient temperature and internal dissipation to evaluate the ceramic package condition, especially in sealed legacy instruments. Keep solder joints and connector contacts free of contamination and inspect the device after repeated thermal cycling. Exact power dissipation and junction-temperature limits must be calculated from the manufacturer operating data and the actual supply and output conditions.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The available product information identifies the lifecycle recommendation and device functionality but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

AD96687BQ datasheet AD96687BQ pinout AD96687BQ datasheet pdf AD96687BQ replacement AD96687BQ equivalent AD96687BQ price AD96687BQ stock AD96687BQ 16 pin CERDIP AD96687BQ 2.5 ns comparator AD96687BQ ECL open emitter AD96687BQ vs AD96685 Analog Devices AD96687BQ AD96687BQ high speed clock circuit AD96687BQ open emitter termination AD96687BQ 50 ps dispersion

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Analog Devices AD96687BQ AD96687 AD96685 dual voltage comparator comparator high-speed comparator logic IC semiconductor ECL open-emitter output complementary output propagation delay propagation-delay dispersion overdrive latch 16-pin CERDIP through-hole package high-speed signal integrity clock qualification pulse-width detection legacy test equipment not recommended for new designs
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন