AD96687BQ - 2.5 ns Dual Ultrafast ECL Comparator | Analog Devices
MPN: AD96687BQ ✗ 停產AD96687BQ 概覽
A high-speed comparator is a semiconductor component that determines whether an input voltage is above or below a reference threshold and then produces a corresponding logic output. The AD96687 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Its dual-channel architecture allows two independent threshold decisions, while its ECL output structure supports high-speed digital signaling in communications, clock, test, and data-conversion systems.
The principal performance characteristics are the 2.5 ns propagation delay, 50 ps propagation-delay dispersion, dual-comparator configuration, latch capability, and complementary open-emitter outputs. Propagation delay describes the time between a comparator input transition and the corresponding output response. Propagation-delay dispersion measures how that delay changes with overdrive, making the 50 ps figure useful when assessing decision timing under different input overdrive conditions.
The AD96687BQ is identified as a 16-pin CERDIP device and uses an ECL output interface with complementary outputs and open-emitter termination. Open-emitter outputs permit wired-connection and termination techniques commonly used in high-speed logic systems. Exact input-common-mode limits, supply requirements, input offset voltage, input capacitance, output levels, and operating-temperature limits must be confirmed in the Analog Devices data sheet before schematic capture or replacement qualification.
Typical uses include high-speed clock recovery, pulse-width qualification, threshold detection, telecom line-interface timing, data-conversion support, and legacy instrumentation. The 2.5 ns delay is the main reason to select this device over slower general-purpose comparators. Open-emitter outputs also make it useful where several outputs must share a common termination or pull-up arrangement, provided the board-level timing and logic-level design is verified carefully.
The primary design caution is board-level signal integrity. A 2.5 ns device leaves little timing margin for long traces, excessive loading, poorly terminated interconnects, or slow output rise and fall times. Keep interconnect paths short, use the recommended termination scheme, provide a low-impedance return path, and validate source and termination compatibility with an oscilloscope or high-speed simulation.
This product record combines manufacturer device information with practical comparisons, replacement criteria, and design guidance. Because the AD96687BQ is not recommended for new designs and no manufacturer-sanctioned drop-in replacement is identified, engineers should first confirm lifecycle requirements, exact pin compatibility, output logic, supply rails, and timing specifications before approving any substitute for an existing AD96687BQ design.
直接替換替代品,適用於 AD96687BQ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品AD96687BQ 最大額定值與電氣特性
| Comparator Type | Dual voltage comparator with latch |
| Number of Channels | 2 channels |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| 輸出配置 | Complementary |
| Output Logic | ECL |
| 輸出類型 | Open-emitter |
| Latch Capability | Yes |
| 封裝 | 16-pin CERDIP |
| 腳位數 | 16 pins |
| Lifecycle Recommendation | Not recommended for new designs |
AD96687BQ 16-pin cerdip 腳位配置指南
AD96687BQ(16-pin cerdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD96687BQ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD96687BQ 適用於 6 應用s: High-Speed Clock Qualification, Pulse-Width Detection, Telecom Line-Interface Timing, Data-Conversion Support, Industrial Control and Instrumentation, Legacy Test Equipment Repair.
High-Speed Clock Qualification
The AD96687BQ is appropriate for legacy clock-qualification circuits that require a rapid threshold decision and two complementary logic outputs. Its 2.5 ns propagation delay leaves only a short interval between an input transition and the corresponding output response, while the 50 ps propagation-delay dispersion provides a defined measure of delay variation with overdrive. The device can compare a clock or pulse against a threshold and generate complementary status signals for downstream timing logic. Because its open-emitter ECL outputs require deliberate termination, the board should use short routes, a continuous ground reference, and the interface arrangement specified by Analog Devices. The part is best treated as a maintenance component because it is not recommended for new designs.
推薦
Pulse-Width Detection
The AD96687BQ can support pulse-width or timing-window detection in legacy high-speed systems by comparing a pulse-derived voltage with a threshold and producing complementary ECL outputs. The dual-channel configuration permits two threshold relationships to be evaluated within one package, and the 2.5 ns propagation delay helps limit the comparator-added portion of the response time. The 50 ps dispersion figure is important when the design evaluates delay variation under different overdrive levels. Open-emitter outputs allow the two channels to be interfaced with an appropriate common termination arrangement. Exact input switching thresholds and common-mode limits must be established from the manufacturer data sheet before defining pulse timing tolerances.
推薦
Telecom Line-Interface Timing
The AD96687BQ is relevant to maintenance of legacy telecom equipment that uses complementary ECL outputs for high-speed threshold decisions. Its 2.5 ns propagation delay and dual-channel architecture are well aligned with receiver timing and pulse-detection functions, while the open-emitter output structure supports conventional ECL wiring practices. A replacement design must preserve the established termination voltage, line loading, and logic polarity. PCB routing should minimize trace length and provide an uninterrupted ground reference because transmission-line effects can consume the timing margin more quickly than the nominal comparator delay. Since the family is not recommended for new designs, new telecom platforms should use a currently supported comparator unless legacy compatibility makes continued AD96687BQ use necessary.
推薦
Data-Conversion Support
The AD96687BQ can serve as a fast threshold detector around high-speed data-conversion and digitization systems, particularly when an existing design uses ECL-compatible signaling. Its 2.5 ns propagation delay allows the comparator stage to respond quickly to an analog crossing, and the dual configuration can monitor two independent thresholds or provide complementary status indications. The 50 ps propagation-delay dispersion should be included in timing analysis because it describes delay changes with overdrive. Analog input conditioning, reference accuracy, and routing remain system-level responsibilities. The legacy CERDIP package and not-for-new-designs status make AD96687BQ most appropriate for maintaining an established converter or clocking subsystem rather than starting an unrestricted new design.
推薦
Industrial Control and Instrumentation
In established industrial control and test-instrumentation equipment, the AD96687BQ can provide fast limit detection for analog signals that require complementary threshold outputs. The dual channels can monitor two limits, generate an over-range indication, or create complementary logic states for a downstream controller. The 2.5 ns propagation delay is useful for minimizing comparator contribution in short measurement windows, while the 50 ps dispersion figure helps characterize behavior across different overdrive conditions. The ECL open-emitter interface must match the existing system logic and termination strategy. Engineers should also account for the input network, reference stability, grounding, and any isolation barriers before treating the comparator as the sole protection mechanism.
推薦
Legacy Test Equipment Repair
The AD96687BQ is particularly useful for repairing legacy oscilloscope, logic-analyzer, pulse-generator, and automated test equipment that originally used this dual ultrafast ECL comparator. A 2.5 ns propagation delay can preserve the intended behavior of fast threshold and trigger paths, while the dual configuration avoids replacing the function with two separate single-channel packages when footprint constraints exist. Exact replacement requires verification of the 16-pin CERDIP pinout, latch behavior, output polarity, supply requirements, common-mode range, and temperature grade. Inspect the ceramic package for damage and verify continuity before installation. For assets that must remain serviceable for many years, stock planning should reflect the device's not-recommended-for-new-designs lifecycle status.
推薦
推薦產品摘要
工程參考資料,適用於 AD96687BQ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | 16-pin CERDIP |
| Brand | Analog Devices |
| Comparator Channels | 2 channels |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| Output Logic | ECL |
| Output Configuration | Complementary open-emitter |
| Latch Capability | Yes |
| Lifecycle Recommendation | Not recommended for new designs |
主要差異化特點
- Dual-channel packaging (對比AD96685)
- Complementary open-emitter ECL output interface (對比AD96685)
- Defined high-speed timing characteristics (對比AD96685)
設計說明
Treat the open-emitter ECL outputs as a high-speed transmission-line interface. Use the termination arrangement specified by Analog Devices, keep traces short, provide a continuous ground reference, and avoid unnecessary stubs or long test-point branches. Validate edge rate, ringing, and receiver setup margin at the logic device rather than relying only on the 2.5 ns nominal propagation delay.
Keep comparator inputs, latch-control connections, and supply decoupling paths compact. Place required termination and bypass components close to their associated pins, and maintain the standard pin-order definition of the 16-pin CERDIP footprint. Verify the physical package drawing because pin numbering and terminal functions must be taken directly from the manufacturer data sheet.
Do not assume that a similarly named AD96687 ordering code is automatically interchangeable. Packaging suffixes may identify different temperature grades, package constructions, or orderable forms. Confirm the exact suffix, operating-temperature grade, lifecycle status, pinout, latch behavior, ECL output configuration, supply rails, and common-mode range before approving a replacement.
Use the maximum expected ambient temperature and internal dissipation to evaluate the ceramic package condition, especially in sealed legacy instruments. Keep solder joints and connector contacts free of contamination and inspect the device after repeated thermal cycling. Exact power dissipation and junction-temperature limits must be calculated from the manufacturer operating data and the actual supply and output conditions.
合規資訊
The available product information identifies the lifecycle recommendation and device functionality but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.