AD96687BQ - 2.5 ns Dual Ultrafast ECL Comparator | Analog Devices
MPN: AD96687BQ ✗ Akhir HayatAD96687BQ Ringkasan
A high-speed comparator is a semiconductor component that determines whether an input voltage is above or below a reference threshold and then produces a corresponding logic output. The AD96687 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Its dual-channel architecture allows two independent threshold decisions, while its ECL output structure supports high-speed digital signaling in communications, clock, test, and data-conversion systems.
The principal performance characteristics are the 2.5 ns propagation delay, 50 ps propagation-delay dispersion, dual-comparator configuration, latch capability, and complementary open-emitter outputs. Propagation delay describes the time between a comparator input transition and the corresponding output response. Propagation-delay dispersion measures how that delay changes with overdrive, making the 50 ps figure useful when assessing decision timing under different input overdrive conditions.
The AD96687BQ is identified as a 16-pin CERDIP device and uses an ECL output interface with complementary outputs and open-emitter termination. Open-emitter outputs permit wired-connection and termination techniques commonly used in high-speed logic systems. Exact input-common-mode limits, supply requirements, input offset voltage, input capacitance, output levels, and operating-temperature limits must be confirmed in the Analog Devices data sheet before schematic capture or replacement qualification.
Typical uses include high-speed clock recovery, pulse-width qualification, threshold detection, telecom line-interface timing, data-conversion support, and legacy instrumentation. The 2.5 ns delay is the main reason to select this device over slower general-purpose comparators. Open-emitter outputs also make it useful where several outputs must share a common termination or pull-up arrangement, provided the board-level timing and logic-level design is verified carefully.
The primary design caution is board-level signal integrity. A 2.5 ns device leaves little timing margin for long traces, excessive loading, poorly terminated interconnects, or slow output rise and fall times. Keep interconnect paths short, use the recommended termination scheme, provide a low-impedance return path, and validate source and termination compatibility with an oscilloscope or high-speed simulation.
This product record combines manufacturer device information with practical comparisons, replacement criteria, and design guidance. Because the AD96687BQ is not recommended for new designs and no manufacturer-sanctioned drop-in replacement is identified, engineers should first confirm lifecycle requirements, exact pin compatibility, output logic, supply rails, and timing specifications before approving any substitute for an existing AD96687BQ design.
Pilihan pengganti yang segera untuk AD96687BQ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Tiada pilihan pengganti yang segera untuk produk ini.
Minta AlternatifAD96687BQ Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | Dual voltage comparator with latch |
| Number of Channels | 2 channels |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| Konfigurasi Output | Complementary |
| Output Logic | ECL |
| Jenis Output | Open-emitter |
| Latch Capability | Yes |
| Kemasan | 16-pin CERDIP |
| Bilangan Pin | 16 pins |
| Lifecycle Recommendation | Not recommended for new designs |
Panduan Konfigurasi Pin AD96687BQ 16-pin cerdip
Konfigurasi pin untuk AD96687BQ (16-pin cerdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk AD96687BQ.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
AD96687BQ patut untuk 6 aplikasis: High-Speed Clock Qualification, Pulse-Width Detection, Telecom Line-Interface Timing, Data-Conversion Support, Industrial Control and Instrumentation, Legacy Test Equipment Repair.
High-Speed Clock Qualification
The AD96687BQ is appropriate for legacy clock-qualification circuits that require a rapid threshold decision and two complementary logic outputs. Its 2.5 ns propagation delay leaves only a short interval between an input transition and the corresponding output response, while the 50 ps propagation-delay dispersion provides a defined measure of delay variation with overdrive. The device can compare a clock or pulse against a threshold and generate complementary status signals for downstream timing logic. Because its open-emitter ECL outputs require deliberate termination, the board should use short routes, a continuous ground reference, and the interface arrangement specified by Analog Devices. The part is best treated as a maintenance component because it is not recommended for new designs.
Disebarkan
Pulse-Width Detection
The AD96687BQ can support pulse-width or timing-window detection in legacy high-speed systems by comparing a pulse-derived voltage with a threshold and producing complementary ECL outputs. The dual-channel configuration permits two threshold relationships to be evaluated within one package, and the 2.5 ns propagation delay helps limit the comparator-added portion of the response time. The 50 ps dispersion figure is important when the design evaluates delay variation under different overdrive levels. Open-emitter outputs allow the two channels to be interfaced with an appropriate common termination arrangement. Exact input switching thresholds and common-mode limits must be established from the manufacturer data sheet before defining pulse timing tolerances.
Disebarkan
Telecom Line-Interface Timing
The AD96687BQ is relevant to maintenance of legacy telecom equipment that uses complementary ECL outputs for high-speed threshold decisions. Its 2.5 ns propagation delay and dual-channel architecture are well aligned with receiver timing and pulse-detection functions, while the open-emitter output structure supports conventional ECL wiring practices. A replacement design must preserve the established termination voltage, line loading, and logic polarity. PCB routing should minimize trace length and provide an uninterrupted ground reference because transmission-line effects can consume the timing margin more quickly than the nominal comparator delay. Since the family is not recommended for new designs, new telecom platforms should use a currently supported comparator unless legacy compatibility makes continued AD96687BQ use necessary.
Disebarkan
Data-Conversion Support
The AD96687BQ can serve as a fast threshold detector around high-speed data-conversion and digitization systems, particularly when an existing design uses ECL-compatible signaling. Its 2.5 ns propagation delay allows the comparator stage to respond quickly to an analog crossing, and the dual configuration can monitor two independent thresholds or provide complementary status indications. The 50 ps propagation-delay dispersion should be included in timing analysis because it describes delay changes with overdrive. Analog input conditioning, reference accuracy, and routing remain system-level responsibilities. The legacy CERDIP package and not-for-new-designs status make AD96687BQ most appropriate for maintaining an established converter or clocking subsystem rather than starting an unrestricted new design.
Disebarkan
Industrial Control and Instrumentation
In established industrial control and test-instrumentation equipment, the AD96687BQ can provide fast limit detection for analog signals that require complementary threshold outputs. The dual channels can monitor two limits, generate an over-range indication, or create complementary logic states for a downstream controller. The 2.5 ns propagation delay is useful for minimizing comparator contribution in short measurement windows, while the 50 ps dispersion figure helps characterize behavior across different overdrive conditions. The ECL open-emitter interface must match the existing system logic and termination strategy. Engineers should also account for the input network, reference stability, grounding, and any isolation barriers before treating the comparator as the sole protection mechanism.
Disebarkan
Legacy Test Equipment Repair
The AD96687BQ is particularly useful for repairing legacy oscilloscope, logic-analyzer, pulse-generator, and automated test equipment that originally used this dual ultrafast ECL comparator. A 2.5 ns propagation delay can preserve the intended behavior of fast threshold and trigger paths, while the dual configuration avoids replacing the function with two separate single-channel packages when footprint constraints exist. Exact replacement requires verification of the 16-pin CERDIP pinout, latch behavior, output polarity, supply requirements, common-mode range, and temperature grade. Inspect the ceramic package for damage and verify continuity before installation. For assets that must remain serviceable for many years, stock planning should reflect the device's not-recommended-for-new-designs lifecycle status.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk AD96687BQ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Package | 16-pin CERDIP |
| Brand | Analog Devices |
| Comparator Channels | 2 channels |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| Output Logic | ECL |
| Output Configuration | Complementary open-emitter |
| Latch Capability | Yes |
| Lifecycle Recommendation | Not recommended for new designs |
Penyeberangsung Jelas
- Dual-channel packaging (vsAD96685)
- Complementary open-emitter ECL output interface (vsAD96685)
- Defined high-speed timing characteristics (vsAD96685)
Catatan Desain
Treat the open-emitter ECL outputs as a high-speed transmission-line interface. Use the termination arrangement specified by Analog Devices, keep traces short, provide a continuous ground reference, and avoid unnecessary stubs or long test-point branches. Validate edge rate, ringing, and receiver setup margin at the logic device rather than relying only on the 2.5 ns nominal propagation delay.
Keep comparator inputs, latch-control connections, and supply decoupling paths compact. Place required termination and bypass components close to their associated pins, and maintain the standard pin-order definition of the 16-pin CERDIP footprint. Verify the physical package drawing because pin numbering and terminal functions must be taken directly from the manufacturer data sheet.
Do not assume that a similarly named AD96687 ordering code is automatically interchangeable. Packaging suffixes may identify different temperature grades, package constructions, or orderable forms. Confirm the exact suffix, operating-temperature grade, lifecycle status, pinout, latch behavior, ECL output configuration, supply rails, and common-mode range before approving a replacement.
Use the maximum expected ambient temperature and internal dissipation to evaluate the ceramic package condition, especially in sealed legacy instruments. Keep solder joints and connector contacts free of contamination and inspect the device after repeated thermal cycling. Exact power dissipation and junction-temperature limits must be calculated from the manufacturer operating data and the actual supply and output conditions.
Maklumat Kesediaan
The available product information identifies the lifecycle recommendation and device functionality but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.