Analog Devices

ADM230LAN - 5V Dual RS-232 Interface | Analog Devices

MPN: ADM230LAN ✗ জীবনকালের সমাপ্তি
5 V Vdss EIA-232-E and V.28 Rds(on) PDIP-14 Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ADM230LAN সারাংশ

Analog Devices ADM230LAN is a 5 V powered CMOS RS-232 driver and receiver interface IC with a 120 kB/s data rate and integrated DC-DC converter, housed in a 14-pin PDIP package. It provides two RS-232 communication channels with approximately 9 V output swing from a single 5 V supply and is designed for systems that cannot provide separate positive and negative RS-232 supply rails.

An RS-232 interface IC is a line-driver and line-receiver device that converts logic-level signals into voltage levels suitable for RS-232 communications. The RS-232 interface sits between a host or controller and an external data link, performing electrical conversion while protecting the transmitting and receiving circuitry from voltage differences on the cable. The ADM230LAN belongs to the CMOS interface-IC hierarchy and supports EIA-232-E and V.28 communication requirements.

The principal features include operation from one 5 V supply, on-board DC-DC conversion, a 120 kB/s maximum data rate, 9 V output swing, small 1 F charge-pump capacitors, a low-power shutdown function, and receiver operation during shutdown. These characteristics make the device useful in systems that need full RS-232 levels without requiring the conventional plus-and-minus supply arrangement.

The integrated DC-DC converter allows the transmitter circuitry to develop the bipolar voltage swing required by RS-232 while the device itself operates from a single 5 V rail. This simplifies system power architecture, although charge-pump capacitor selection, startup behavior, and output slew rate still require attention in high-speed or long-cable applications. The CMOS implementation supports the 120 kB/s signaling rate identified for this device family.

Typical applications include point-of-sale terminals, serial instrumentation, industrial control equipment, data acquisition systems, and legacy peripheral interfaces. The ADM230LAN is particularly suitable when an embedded controller uses TTL or CMOS logic but the connected equipment requires an RS-232 port. It can also support bidirectional serial links when both sides of the interface are wired for communication rather than permanently configured as DTE or DCE.

When laying out the circuit, place the charge-pump capacitors and interface bypass capacitors close to their associated pins, and route the RS-232 driver and receiver traces away from sensitive clock, reset, and analog signals. Confirm signal polarity, grounding, and DTE-versus-DCE assignments before connecting equipment because a physically wired RS-232 link can fail even when both devices meet the same electrical specifications.

This page organizes the ADM230LAN specifications, sourcing information, compatible alternatives, and application guidance into a practical engineering reference. It also highlights the trade-offs involved when selecting an integrated single-supply transceiver for industrial, instrument, and embedded serial communication systems.

এর জন্য ড্রপ-ইন বিকল্প ADM230LAN — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible ADM230LAN (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Supply Voltage, Product Type.

Analog Devices
Package: 20-CDIP, 0.300 in (7.62 mm)
Product Type: 5 V powered CMOS RS-232 drivers/receivers
এর সাথে তুলনা করুন ADM230LAN →
Analog Devices
Package: PDIP-20 (plastic DIP-20)
Supply Voltage: +5 V (single supply)
এর সাথে তুলনা করুন ADM230LAN →

ADM230LJN

✅ ড্রপ-ইন
Analog Devices
📦 PDIP-14
RS-232 line driver / receiver (transceiver) · +5 V (single supply) · 120 kbps · EIA-232-E / V.28 · 0 °C to +70 °C · PDIP-20 (plastic DIP-20) · 20 pins · Through-hole

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

ADM230LAQ

✅ ড্রপ-ইন
Analog Devices
📦 PDIP-14
5 V powered CMOS RS-232 drivers/receivers · 5 V · 5 channels · 120 kB/s · 9 V · 1 A · 30 V · 1 F

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

ADM230LAN বিশেষণ

Product Type Dual RS-232 driver and receiver interface IC
সাপ্লাই ভোল্টেজ 5 V
Supply Configuration Single positive 5 V supply
Logic Technology CMOS
Maximum Data Rate 120 kB/s
RS-232 Output Swing 9 V
DC-DC Converter On-board
Charge-Pump Capacitor Value 1 F
Power Shutdown Low-power shutdown supported
Receiver Operation During Shutdown Receivers remain active
Receiver Input Voltage 30 V
RS-232 Standards EIA-232-E and V.28
প্যাকেজ PDIP-14
মাউন্টিং টাইপ Through-hole
পিনের সংখ্যা 14 pins

ADM230LAN pdip-14 পিন কনফিগারেশন গাইড

ADM230LAN (pdip-14 প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

ADM230LAN-এর জন্য pdip-14 প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADM230LAN.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ADM230LAN এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Point-of-Sale Terminal Interfaces, Industrial Serial Instrumentation, Data Acquisition Systems, Embedded Controller Serial Bridges, Legacy Peripheral Connectivity, Security and Access-Control Equipment.

🖥️

Point-of-Sale Terminal Interfaces

The ADM230LAN fits point-of-sale equipment that must connect a low-voltage controller to a legacy RS-232 peripheral. Its single 5 V supply eliminates the need for a separate positive and negative RS-232 rail, while the on-board DC-DC converter supports approximately 9 V of output swing. The 120 kB/s data rate is suitable for many receipt printers, scanners, and customer-display devices. Place the 1 F charge-pump capacitors and bypass capacitors close to the device, and confirm whether the peripheral expects DTE or DCE signal assignments before wiring the cable.

🏭

Industrial Serial Instrumentation

The ADM230LAN is appropriate for industrial instruments that expose an RS-232 configuration or maintenance port. The 5 V CMOS interface reduces the power-supply burden compared with a traditional bipolar RS-232 implementation, while the 120 kB/s rate supports configuration exchanges and moderate-rate telemetry. Its 30 V receiver input rating adds tolerance for externally applied interface signals, although it does not replace dedicated surge protection. Validate the operating temperature grade, isolation strategy, enclosure grounding, and applicable industrial immunity requirements before deployment.

📟

Data Acquisition Systems

The ADM230LAN can provide a legacy serial bridge in data acquisition systems whose controller operates with CMOS logic but whose external instrument uses RS-232. The integrated DC-DC converter permits operation from one 5 V rail, and the 120 kB/s data rate is useful for command traffic and sampled data streams that do not require high-speed serial links. The 14-pin PDIP package is easy to prototype and rework. Keep the RS-232 traces separated from sensitive analog inputs and use the circuit reference layout to control charge-pump noise near the converter.

🔧

Embedded Controller Serial Bridges

The ADM230LAN is useful when an embedded controller needs to communicate with equipment that retains an RS-232 port. Because the device accepts a single 5 V supply and includes its own DC-DC converter, it can simplify interface isolation and power distribution around a 3.3 V or 5 V controller. The 120 kB/s limit should be checked against the protocol's baud rate and framing overhead. Disable unused channels where appropriate, use controlled signal levels, and verify that software accounts for the RS-232 voltage polarity used by the connected DTE or DCE equipment.

🖨️

Legacy Peripheral Connectivity

The ADM230LAN supports cost-conscious designs that must retain compatibility with legacy RS-232 printers, scales, programmers, or service interfaces. A 5 V supply reduces the number of external rails, while the on-board converter preserves the bipolar signaling expected by RS-232 equipment. The 120 kB/s ceiling accommodates many command-oriented legacy protocols. Before installation, verify the connector gender, signal-ground arrangement, logic polarity, and whether the peripheral uses DTE or DCE timing. A software loopback test is recommended during production validation.

🧩

Security and Access-Control Equipment

The ADM230LAN can be used in access-control or security-system accessories that maintain an RS-232 service or configuration link. Its single 5 V operation is useful in compact equipment, and the receiver can remain active during shutdown when a low-power state must still monitor an incoming signal. The 30 V receiver input rating should not be interpreted as complete surge immunity, so cable protection may still be required for long or exposed installations. Confirm the equipment's grounding policy and test compatibility with the attached controller before field deployment.

What is the ADM230LAN?
The ADM230LAN is a 5 V powered CMOS RS-232 driver and receiver interface IC for serial communications. According to the Analog Devices manufacturer datasheet, it operates from a single 5 V supply, supports a maximum data rate of 120 kB/s, provides approximately 9 V of RS-232 output swing, and includes an on-board DC-DC converter. The device is offered in a 14-pin PDIP package.
What is the operating voltage of the ADM230LAN?
The ADM230LAN operates from a single 5 V supply. The Analog Devices manufacturer datasheet identifies an on-board DC-DC converter, allowing the RS-232 driver section to produce bipolar output levels from one positive supply rail. This differs from conventional RS-232 implementations that use positive and negative supply voltages. External circuitry must still provide a valid ground reference between connected RS-232 equipment.
What is the maximum data rate of the ADM230LAN?
The ADM230LAN supports a maximum data rate of 120 kB/s. The Analog Devices manufacturer datasheet lists this rate as a principal feature of the ADM2xx interface family. Actual application throughput can be lower because of cable length, receiver bandwidth, timing margin, protocol overhead, and the data format transmitted over the RS-232 link.
Does the ADM230LAN need external positive and negative supplies?
No. The ADM230LAN requires a single 5 V supply because its on-board DC-DC converter generates the voltage needed for RS-232 output swing. The Analog Devices manufacturer datasheet identifies approximately 9 V output swing from the 5 V supply. Charge-pump capacitors are required to support that converter, and their placement and capacitance values should follow the datasheet reference circuit.
Where can I download the ADM230LAN datasheet PDF?
The ADM230LAN datasheet PDF is linked from the Analog Devices manufacturer documentation and is also accessible through the datasheet listing on this page. The document covers the 5 V supply requirement, 120 kB/s data rate, on-board DC-DC converter, approximately 9 V output swing, shutdown behavior, electrical characteristics, and the ADM230L family application information. Use the manufacturer document as the authority for pin functions and final circuit values.
Where can I find the ADM230LAN pinout?
The ADM230LAN uses a 14-pin PDIP package, and its pin functions should be assigned from the pin-description table in the Analog Devices manufacturer datasheet. The 14-pin package outline is represented by the package diagram selected for this page. Because an exact numbered pin list is not shown here, use the datasheet pin-description table before assigning PCB nets or designing the footprint.
Can the ADM230LAN receivers operate while the device is in shutdown?
Yes. The Analog Devices manufacturer datasheet identifies the receiver section as active during shutdown. This feature allows a system to continue receiving a remote serial signal while the transmitter and selected power-management functions are disabled. The application must still provide the required supply and ground connections, and signal levels must remain within the receiver input rating of 30 V.
What is the best drop-in replacement for the ADM230LAN?
The ADM230LJN is a documented drop-in candidate for the ADM230LAN because it belongs to the same Analog Devices ADM230L family and is associated with the same 14-pin PDIP interface arrangement. The Analog Devices manufacturer datasheet should be used to confirm pin functions, temperature grade, and ordering details before substitution. Both devices use a single 5 V supply and support the same 120 kB/s family data rate.
Can the ADM230LAQ replace the ADM230LAN?
The ADM230LAQ can be considered as a pin-compatible ADM230L-family alternative when its temperature and qualification requirements are appropriate for the application. It retains the single 5 V architecture and 120 kB/s family performance, while its automotive-oriented ordering designation may differ from the commercial ADM230LAN. Confirm the exact package, temperature range, and lifecycle status against the Analog Devices manufacturer datasheet.
ADM230LAN versus ADM230LJN: which interface IC should I choose?
Choose the ADM230LAN when it matches the required grade, lifecycle status, and ordering configuration; choose the ADM230LJN when its documented package and temperature characteristics fit the design better. Both are associated with the same Analog Devices ADM230L family, 5 V single-supply operation, integrated DC-DC converter, and 120 kB/s data rate. Check the ordering table and lifecycle information before making a production substitution.
When should I choose the ADM230LAN instead of a discrete RS-232 transceiver?
Choose the ADM230LAN when the design needs a compact single-supply RS-232 solution with integrated DC-DC conversion and a 120 kB/s data rate. A discrete transceiver can offer greater freedom in power architecture and component selection, but it generally requires more board area and design effort. The ADM230LAN is advantageous when PCB space and implementation simplicity outweigh the need for a customized power stage.
Is the ADM230LAN suitable for industrial serial communication equipment?
The ADM230LAN is suitable for industrial serial interfaces when its specified operating temperature and lifecycle status meet the equipment requirements. Its single 5 V supply, integrated DC-DC converter, 120 kB/s data rate, and approximately 9 V output swing simplify systems that cannot provide conventional positive and negative RS-232 rails. Confirm temperature, isolation, grounding, and electromagnetic-compatibility requirements separately.
What is the best Analog Devices equivalent for the ADM230LAN?
The Analog Devices ADM230LJN is the closest documented same-family option for a 14-pin PDIP drop-in consideration because it uses the same ADM230L single-supply interface architecture and 120 kB/s performance class. The ADM230LAQ is another family alternative for applications whose qualification and temperature requirements match that variant. Verify package details and production availability before finalizing a replacement.
What can replace the ADM230LAN?
The ADM230LJN can replace the ADM230LAN when its exact pinout, electrical limits, temperature grade, and lifecycle status have been checked against the target design. Both devices are members of the Analog Devices ADM230L interface family and share the 5 V single-supply architecture and 120 kB/s data-rate class. An automotive-oriented ADM230LAQ may also be considered when its qualification profile suits the end product.
Is the ADM230LAN the same as the ADM230LJN?
The ADM230LAN and ADM230LJN are closely related ADM230L-family devices, but they are not interchangeable solely because they share the 5 V supply and 120 kB/s data-rate class. The package suffix, temperature grade, electrical limits, qualification, and lifecycle status must be compared in the Analog Devices manufacturer datasheet. A PCB replacement should follow only after those ordering and specification differences are resolved.
What are the key specifications of the ADM230LAN that engineers should know?
The ADM230LAN is a dual RS-232 interface IC with a 5 V supply, 120 kB/s data rate, on-board DC-DC converter, approximately 9 V output swing, 1 F charge-pump capacitors, low-power shutdown, and receiver operation during shutdown. The Analog Devices manufacturer datasheet also identifies EIA-232-E and V.28 support and a 30 V receiver input rating. Its 14-pin PDIP package makes it suitable for through-hole industrial and instrument designs.
Where can I buy the ADM230LAN and check its lead time?
Use the Request a Quote form on this page to ask about ADM230LAN pricing, current inventory, minimum order quantity, and production lead time. Quote requests allow the current supply position and exact suffix to be checked without relying on a stale price or generic listing. Include the required package, quantity, target date, and any automotive-grade requirements with the request.
What is the price of the ADM230LAN?
Current ADM230LAN pricing depends on the exact ordering suffix, quantity, packaging configuration, and supply position. Use the Request a Quote form on this page to request a current quotation and volume-break review. The quote team can confirm the applicable tier structure for the ADM230LAN rather than presenting a static price that may not reflect current availability.
Is the ADM230LAN in stock and what is its lead time?
Stock and lead time for the ADM230LAN should be confirmed through the Request a Quote form on this page. Include the required quantity, annual usage, date code needs, and acceptable packaging details. Because the device is distributed through multiple channels, current inventory and production allocation can vary by suffix and order quantity, making a direct availability check the most reliable approach.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADM230LAN — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ADM230LAN when the design needs a straightforward, single 5 V RS-232 interface with a 120 kB/s data rate, integrated DC-DC conversion, and approximately 9 V output swing. Its 14-pin PDIP format is particularly useful for through-hole prototypes, legacy equipment, and repair-oriented industrial products. Choose the ADM230LJN when its documented ordering suffix, temperature range, lifecycle status, and availability better match the production design. Consider the ADM230LAQ when its automotive-oriented qualification profile is required and the ordering conditions match the application. Both documented alternatives remain in the ADM230L family and use the same core single-supply architecture, but they are not selected solely on package name: verify pin functions, temperature limits, electrical characteristics, qualification, and supply status. For designs requiring higher speed, galvanic isolation, adjustable charge-pump capacitors, or a smaller surface-mount footprint, consider a different RS-232 interface family rather than forcing a drop-in substitution.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ADM230LJN ADM230LAQ
Manufacturer Analog Devices Analog Devices Analog Devices
Package PDIP-14 PDIP-14 PDIP-14
Supply Voltage 5 V 5 V 5 V
Maximum Data Rate 120 kB/s 120 kB/s 120 kB/s

মূল পার্থক্যসমূহ

  • Single-supply RS-232 implementation (বনামADM230LJN)
  • Established 120 kB/s communications class (বনামADM230LAQ)
  • Receiver availability during low-power shutdown (বনামADM230LJN)

ডিজাইন নোট

Place the 1 F charge-pump capacitors and local supply bypass components close to their specified ADM230LAN pins, following the Analog Devices manufacturer datasheet layout. Keep these high-current paths compact and connect the device ground directly to the interface ground reference. Long capacitor or supply routes can increase converter noise and make output behavior less repeatable, particularly when the transceiver operates near its 120 kB/s limit.

Route RS-232 driver outputs and receiver inputs away from clock, reset, ADC reference, and other sensitive analog nodes. The integrated DC-DC converter can couple switching energy into surrounding circuitry even though the complete interface operates from one supply rail. Use a quiet ground strategy, avoid routing return current beneath the transceiver, and maintain the separation recommended by the datasheet reference layout.

Do not infer DTE or DCE behavior from the IC alone; signal names, logic polarity, connector gender, and wiring must agree at both ends of the cable. Verify the receiver threshold, shutdown state, and supply sequence in hardware. A loopback test with representative software and peripheral equipment can expose swapped signals, incorrect grounding, or protocol assumptions before the board is deployed.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

Compliance declarations are not identified in the manufacturer material cited for this page. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status using the current manufacturer product documentation before qualification.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

ADM230LAN datasheet ADM230LAN datasheet pdf ADM230LAN pinout ADM230LAN specifications ADM230LAN equivalent ADM230LAN replacement ADM230LAN drop-in replacement ADM230LAN vs ADM230LJN ADM230LAN vs ADM230LAQ Analog Devices ADM230LAN ADM230LAN PDIP-14 pinout ADM230LAN application circuit ADM230LAN price ADM230LAN stock ADM230LAN 5V 120kB/s

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Analog Devices ADM230LAN ADM230LJN ADM230LAQ RS-232 EIA-232-E V.28 CMOS RS-232 transceiver line driver line receiver interface IC single-supply interface DC-DC converter charge-pump capacitor 5 V power supply 120 kB/s 9 V output swing low-power shutdown 30 V receiver input PDIP-14 DIP package family through-hole mounting serial communication RS-232 interface
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন