ADM230LAN - 5V Dual RS-232 Interface | Analog Devices
MPN: ADM230LAN ✗ Cuối đờiADM230LAN Tóm tắt
An RS-232 interface IC is a line-driver and line-receiver device that converts logic-level signals into voltage levels suitable for RS-232 communications. The RS-232 interface sits between a host or controller and an external data link, performing electrical conversion while protecting the transmitting and receiving circuitry from voltage differences on the cable. The ADM230LAN belongs to the CMOS interface-IC hierarchy and supports EIA-232-E and V.28 communication requirements.
The principal features include operation from one 5 V supply, on-board DC-DC conversion, a 120 kB/s maximum data rate, 9 V output swing, small 1 F charge-pump capacitors, a low-power shutdown function, and receiver operation during shutdown. These characteristics make the device useful in systems that need full RS-232 levels without requiring the conventional plus-and-minus supply arrangement.
The integrated DC-DC converter allows the transmitter circuitry to develop the bipolar voltage swing required by RS-232 while the device itself operates from a single 5 V rail. This simplifies system power architecture, although charge-pump capacitor selection, startup behavior, and output slew rate still require attention in high-speed or long-cable applications. The CMOS implementation supports the 120 kB/s signaling rate identified for this device family.
Typical applications include point-of-sale terminals, serial instrumentation, industrial control equipment, data acquisition systems, and legacy peripheral interfaces. The ADM230LAN is particularly suitable when an embedded controller uses TTL or CMOS logic but the connected equipment requires an RS-232 port. It can also support bidirectional serial links when both sides of the interface are wired for communication rather than permanently configured as DTE or DCE.
When laying out the circuit, place the charge-pump capacitors and interface bypass capacitors close to their associated pins, and route the RS-232 driver and receiver traces away from sensitive clock, reset, and analog signals. Confirm signal polarity, grounding, and DTE-versus-DCE assignments before connecting equipment because a physically wired RS-232 link can fail even when both devices meet the same electrical specifications.
This page organizes the ADM230LAN specifications, sourcing information, compatible alternatives, and application guidance into a practical engineering reference. It also highlights the trade-offs involved when selecting an integrated single-supply transceiver for industrial, instrument, and embedded serial communication systems.
Bộ thay thế dễ dàng lắp đặt cho ADM230LAN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM230LAN (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage, Product Type.
ADM230LJN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM230LAQ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM230LAN Thông số kỹ thuật
| Product Type | Dual RS-232 driver and receiver interface IC |
| Điện áp cung cấp | 5 V |
| Supply Configuration | Single positive 5 V supply |
| Logic Technology | CMOS |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | 9 V |
| DC-DC Converter | On-board |
| Charge-Pump Capacitor Value | 1 F |
| Power Shutdown | Low-power shutdown supported |
| Receiver Operation During Shutdown | Receivers remain active |
| Receiver Input Voltage | 30 V |
| RS-232 Standards | EIA-232-E and V.28 |
| Hộp | PDIP-14 |
| Kiểu lắp đặt | Through-hole |
| Số lượng chân | 14 pins |
Hướng dẫn cấu hình chân ADM230LAN pdip-14
Cấu hình chân cho ADM230LAN (pdip-14 gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM230LAN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM230LAN phù hợp cho 6 Áp dụngs: Point-of-Sale Terminal Interfaces, Industrial Serial Instrumentation, Data Acquisition Systems, Embedded Controller Serial Bridges, Legacy Peripheral Connectivity, Security and Access-Control Equipment.
Point-of-Sale Terminal Interfaces
The ADM230LAN fits point-of-sale equipment that must connect a low-voltage controller to a legacy RS-232 peripheral. Its single 5 V supply eliminates the need for a separate positive and negative RS-232 rail, while the on-board DC-DC converter supports approximately 9 V of output swing. The 120 kB/s data rate is suitable for many receipt printers, scanners, and customer-display devices. Place the 1 F charge-pump capacitors and bypass capacitors close to the device, and confirm whether the peripheral expects DTE or DCE signal assignments before wiring the cable.
Được đề xuất
Industrial Serial Instrumentation
The ADM230LAN is appropriate for industrial instruments that expose an RS-232 configuration or maintenance port. The 5 V CMOS interface reduces the power-supply burden compared with a traditional bipolar RS-232 implementation, while the 120 kB/s rate supports configuration exchanges and moderate-rate telemetry. Its 30 V receiver input rating adds tolerance for externally applied interface signals, although it does not replace dedicated surge protection. Validate the operating temperature grade, isolation strategy, enclosure grounding, and applicable industrial immunity requirements before deployment.
Được đề xuất
Data Acquisition Systems
The ADM230LAN can provide a legacy serial bridge in data acquisition systems whose controller operates with CMOS logic but whose external instrument uses RS-232. The integrated DC-DC converter permits operation from one 5 V rail, and the 120 kB/s data rate is useful for command traffic and sampled data streams that do not require high-speed serial links. The 14-pin PDIP package is easy to prototype and rework. Keep the RS-232 traces separated from sensitive analog inputs and use the circuit reference layout to control charge-pump noise near the converter.
Được đề xuất
Embedded Controller Serial Bridges
The ADM230LAN is useful when an embedded controller needs to communicate with equipment that retains an RS-232 port. Because the device accepts a single 5 V supply and includes its own DC-DC converter, it can simplify interface isolation and power distribution around a 3.3 V or 5 V controller. The 120 kB/s limit should be checked against the protocol's baud rate and framing overhead. Disable unused channels where appropriate, use controlled signal levels, and verify that software accounts for the RS-232 voltage polarity used by the connected DTE or DCE equipment.
Được đề xuất
Legacy Peripheral Connectivity
The ADM230LAN supports cost-conscious designs that must retain compatibility with legacy RS-232 printers, scales, programmers, or service interfaces. A 5 V supply reduces the number of external rails, while the on-board converter preserves the bipolar signaling expected by RS-232 equipment. The 120 kB/s ceiling accommodates many command-oriented legacy protocols. Before installation, verify the connector gender, signal-ground arrangement, logic polarity, and whether the peripheral uses DTE or DCE timing. A software loopback test is recommended during production validation.
Được đề xuất
Security and Access-Control Equipment
The ADM230LAN can be used in access-control or security-system accessories that maintain an RS-232 service or configuration link. Its single 5 V operation is useful in compact equipment, and the receiver can remain active during shutdown when a low-power state must still monitor an incoming signal. The 30 V receiver input rating should not be interpreted as complete surge immunity, so cable protection may still be required for long or exposed installations. Confirm the equipment's grounding policy and test compatibility with the attached controller before field deployment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM230LAN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM230LJN | ADM230LAQ |
|---|---|---|---|
| Manufacturer | Analog Devices | Analog Devices | Analog Devices |
| Package | PDIP-14 | PDIP-14 | PDIP-14 |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 120 kB/s | 120 kB/s | 120 kB/s |
Bảo phân biệt quan trọng
- Single-supply RS-232 implementation (vsADM230LJN)
- Established 120 kB/s communications class (vsADM230LAQ)
- Receiver availability during low-power shutdown (vsADM230LJN)
Ghi chú thiết kế
Place the 1 F charge-pump capacitors and local supply bypass components close to their specified ADM230LAN pins, following the Analog Devices manufacturer datasheet layout. Keep these high-current paths compact and connect the device ground directly to the interface ground reference. Long capacitor or supply routes can increase converter noise and make output behavior less repeatable, particularly when the transceiver operates near its 120 kB/s limit.
Route RS-232 driver outputs and receiver inputs away from clock, reset, ADC reference, and other sensitive analog nodes. The integrated DC-DC converter can couple switching energy into surrounding circuitry even though the complete interface operates from one supply rail. Use a quiet ground strategy, avoid routing return current beneath the transceiver, and maintain the separation recommended by the datasheet reference layout.
Do not infer DTE or DCE behavior from the IC alone; signal names, logic polarity, connector gender, and wiring must agree at both ends of the cable. Verify the receiver threshold, shutdown state, and supply sequence in hardware. A loopback test with representative software and peripheral equipment can expose swapped signals, incorrect grounding, or protocol assumptions before the board is deployed.
Thông tin tuân thủ
Compliance declarations are not identified in the manufacturer material cited for this page. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status using the current manufacturer product documentation before qualification.