Texas Instruments

ADS574JH - 12-Bit 40 kSPS Parallel SAR ADC, 28-Pin DIP | Texas Instruments

MPN: ADS574JH ✓ সক্রিয়
5 V Vdss 28-pin plastic DIP (through-hole) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ADS574JH সারাংশ

The Texas Instruments ADS574JH is a 12-bit successive-approximation (SAR) analog-to-digital converter with a parallel 12-bit output bus, a conversion throughput of 40 kSPS, and a single 5 V analog supply, packaged in a 28-pin plastic DIP (through-hole) package specified for 0 °C to +70 °C.

An SAR ADC is one of the two dominant ADC architectures, alongside flash and delta-sigma converters. Each conversion cycle applies a sequence of internal comparator trials, resolving the analog input into a digital code in a fixed, deterministic number of clock periods. Because the conversion time is fixed and independent of input voltage, SAR converters deliver deterministic latency with no pipeline fill, and they are typically preferred wherever a sampled measurement must line up predictably with a control or comms cycle.

Key features of the ADS574JH include 12-bit resolution, single-channel conversion at 40 kSPS, a parallel digital output that transfers the complete code directly into a bus without serial clocking, operation from a single 5 V supply, and a 28-pin through-hole DIP footprint that simplifies both prototyping and legacy instrument refurbishment.

Technically, the device belongs to the classic ADS57x family of parallel-output SAR converters originally introduced by Burr-Brown and now supported by Texas Instruments. The parallel interface removes the need for a serial data clock, so the 12 output lines can be wired straight into a microcontroller data bus, an FPGA capture register, or a latch. Throughput of 40 kSPS is generous for slow industrial and motor-control variables such as shaft position, current feedback, or temperature, and the DIP package keeps the part attractive for designs where surface-mount assembly is not practical.

Typical uses include brushless DC and servo motor phase-current sensing, industrial pressure and level instrumentation, laboratory data acquisition, and position-feedback decoding in printers and robotics.

Designers should pay attention to three points: route the 12 parallel data lines as a matched-length group to avoid skew between bit lines, place the analog supply bypass capacitors directly at the device pins, and allow the full settling period between conversions if the source impedance is high.

This page consolidates manufacturer specifications, package and grade details, drop-in alternatives from the same converter family, and practical interface guidance into a single engineering reference for engineers evaluating legacy 12-bit parallel SAR converters.

এর জন্য ড্রপ-ইন বিকল্প ADS574JH — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible ADS574JH (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Supply Voltage, Mounting Type, Microprocessor Interface, RoHS Status.

Texas Instruments
Package: 28-pin PDIP through-hole
Supply Voltage: +5 V (single supply)
Mounting Type: Through-Hole
এর সাথে তুলনা করুন ADS574JH →
Texas Instruments
Package: 28-pin PDIP
Supply Voltage: +5 V
Mounting Type: Through-hole
এর সাথে তুলনা করুন ADS574JH →
Texas Instruments
Package: 28-pin PDIP
Supply Voltage: +5 V
Mounting Type: Through-hole
এর সাথে তুলনা করুন ADS574JH →

ADS574KE

✅ ড্রপ-ইন
Texas Instruments
📦 DIP-28
12 bit · 1 analog input · Successive approximation (SAR) · 40 kSPS · 25 µs · +5 V · Yes · Yes

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

ADS574JE

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
Texas Instruments
📦 DIP-28
12 bit · SAR (Successive Approximation) · 40 kSPS · 1 · 25 µs max · +5 V (single supply) · 0 to +10 V, 0 to +20 V, ±5 V, ±10 V · Yes (internal)

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

ADS574JG

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 DIP-28
Same 12-bit SAR core, 5 V supply and 28-pin DIP footprint; alternate lead-finish ordering code with the same commercial 0 °C to +70 °C grade

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ADS574JP

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
Texas Instruments
📦 DIP-28
12 bit · 1 channel · Successive approximation (SAR) · 25 µs · +5 V · Low-power CMOS · 28-pin PDIP · Through-hole

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

ADS574KG

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 DIP-28
Same 12-bit SAR core, 5 V supply and 28-pin DIP footprint; extended -40 °C to +85 °C grade with an alternate lead-finish code versus the ADS574JH commercial grade

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ADS574JH সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

ADC Type Successive approximation (SAR), single-channel
রেজোলিউশন 12 bit
Conversion Throughput 40 kSPS
Output Interface Parallel, 12-bit digital output bus
সাপ্লাই ভোল্টেজ 5 V
Number of Channels 1
Resolution Step 1 LSB
প্যাকেজ 28-pin plastic DIP (through-hole)
Package Code DIP, rectangular
Number of Terminals 28
Terminal Form Through-hole
মাউন্টিং টাইপ Through-hole (THT)
Temperature Grade Commercial
অপারেটিং তাপমাত্রার পরিসর 0 °C to +70 °C
RoHS স্ট্যাটাস Compliant (per distributor product listing)

ADS574JH dip, rectangular পিন কনফিগারেশন গাইড

ADS574JH (dip, rectangular প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

ADS574JH-এর জন্য dip, rectangular প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADS574JH.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ADS574JH এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Motor Phase-Current Sensing, Industrial Pressure and Level Instrumentation, Laboratory Data Acquisition and Instrumentation, Position and Encoder Feedback Decoding, Power Supply and Inverter Monitoring, Legacy Test Equipment and Line Retrofits.

🏭

Motor Phase-Current Sensing

The ADS574JH suits brushless DC and servo drive front ends that digitise low-bandwidth phase current or DC-link voltage for the control loop. A conversion throughput of 40 kSPS is comfortably above the tens of kilohertz current-loop bandwidth typical of industrial drives, and the fixed SAR conversion latency lets the sample instant be scheduled against a defined point in the PWM cycle. The 12 parallel data lines connect straight to the controller bus without a serial data clock, shortening the feedback path. Place the converter adjacent to the current-sense amplifier and reference it to the same analog ground so the 12-bit code remains meaningful at small shunt voltages.

⚡

Industrial Pressure and Level Instrumentation

Process instrumentation built around resistive or capacitive transducers commonly needs a compact, deterministic converter for slow-changing analog signals. The ADS574JH provides 12-bit resolution at 40 kSPS in a 28-pin plastic DIP, a package that is easy to socket for field serviceable transmitters. Because SAR conversion time is fixed and independent of input level, the instrument controller can run deterministic sampling intervals and apply digital linearisation and temperature compensation without variable latency artefacts. The single 5 V supply also simplifies power budgeting in transmitters that already regulate a 5 V rail from an isolated converter.

🖥️

Laboratory Data Acquisition and Instrumentation

Bench instruments that capture slow analog waveforms, calibration tables or transducer outputs benefit from the deterministic behaviour and simple hookup of a parallel-output SAR converter. The ADS574JH drives its 12-bit code directly onto a data bus, so a microcontroller can latch the value on the conversion-complete signal and forward it over USB or Ethernet without bit-serialisation firmware. The 40 kSPS ceiling supports sampling of thermal, pressure and position channels at rates well above the underlying mechanical bandwidths, and the through-hole DIP package allows socketed replacement on long-lived laboratory hardware.

🤖

Position and Encoder Feedback Decoding

Incremental encoder counters, linear position transducers and servo feedback loops need a converter whose sampling delay is predictable so that position estimates align with the mechanical reference. The ADS574JH resolves each sample in a fixed number of clock periods at up to 40 kSPS, giving the controller a deterministic latency budget for interpolation and filtering. The 12-bit parallel output avoids the serial clocking overhead that limits the update rate of many serial-interface converters. Keep the analog input path short and shielded, and synchronise the sample command to the encoder index pulse to avoid ambiguity near a count rollover.

🔋

Power Supply and Inverter Monitoring

Inverters, battery management controllers and power quality analysers routinely digitise bus voltages, output currents and temperature probes for supervisory functions rather than for high-bandwidth control loops. The ADS574JH is appropriate for these supervisory channels because 40 kSPS is far above the required update rate and the 12-bit code is ample for metering and protection thresholds. Its parallel output bus shares the same 5 V supply domain as most controller logic, simplifying level considerations, while the DIP package remains easy to socket in field-replaceable power modules. Provide local bulk and ceramic decoupling close to the analog supply pins to keep switching-node ripple off the reference.

🔧

Legacy Test Equipment and Line Retrofits

Refurbishing bench instruments, panel meters and production test fixtures often requires replacing a through-hole parallel converter rather than re-laying out a mixed-signal board. The ADS574JH in a 28-pin plastic DIP allows a direct socket-level or footprint-level swap in equipment designed around the original parallel 12-bit interface, avoiding the schematic, layout and firmware rework that a serial-interface replacement would demand. Its commercial 0 °C to +70 °C rating suits indoor factory and laboratory environments. When selecting a substitute for a wider temperature window, the extended-grade member of the same family shares the identical pinout and lead dimensions.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

ADS8329 companion SAR ADC for higher-resolution current feedback ব্যবহৃত হয়: Motor Phase-Current Sensing, Laboratory Data Acquisition and Instrumentation, Power Supply and Inverter Monitoring, Legacy Test Equipment and Line Retrofits OPA197 precision instrumentation amplifier for the shunt front end ব্যবহৃত হয়: Motor Phase-Current Sensing, Industrial Pressure and Level Instrumentation, Laboratory Data Acquisition and Instrumentation, Position and Encoder Feedback Decoding, Power Supply and Inverter Monitoring, Legacy Test Equipment and Line Retrofits REF5040 low-noise voltage reference for the analog supply ব্যবহৃত হয়: Motor Phase-Current Sensing, Industrial Pressure and Level Instrumentation, Position and Encoder Feedback Decoding, Power Supply and Inverter Monitoring SN74LVC245 level-shifting bus buffer for the parallel output ব্যবহৃত হয়: Industrial Pressure and Level Instrumentation, Laboratory Data Acquisition and Instrumentation, Position and Encoder Feedback Decoding, Legacy Test Equipment and Line Retrofits
What is the ADS574JH?
The ADS574JH is a 12-bit, single-channel, parallel-output successive-approximation analog-to-digital converter from Texas Instruments, converting analog signals into a 12-bit digital code at up to 40 kSPS from a single 5 V supply. The device is packaged in a 28-pin plastic DIP through-hole package and is specified for the commercial 0 °C to +70 °C temperature grade. Because the output is presented as a parallel bus, no serial data clock is required, which simplifies connection to microcontrollers, FPGAs and data-capture logic.
What is the resolution and conversion rate of the ADS574JH?
The ADS574JH delivers 12-bit resolution at a conversion throughput of 40 kSPS. That combination gives roughly 2.9 microseconds of full-scale conversion time, which is fast enough for most slow industrial, instrumentation and motor-feedback loops. The 12-bit code corresponds to 4096 discrete levels, one LSB per code step. For measurements that require more dynamic range or faster sampling, a higher-resolution or higher-rate converter from the same supplier family would be the natural next step.
What package does the ADS574JH come in?
The ADS574JH is offered in a 28-pin plastic DIP package with a rectangular body and through-hole terminal form. The DIP footprint is a deliberate choice for laboratory, instrumentation and legacy industrial equipment where hand insertion, socketed prototyping and field replacement of a through-hole part are all still required. The 28 terminals also include the analog supply, digital supply, control signals, analog input and the 12 parallel data lines, plus any associated reference and control pins described in the manufacturer datasheet.
What is the operating temperature range of the ADS574JH?
The ADS574JH is rated for 0 °C to +70 °C, which places it in the commercial temperature grade. This makes it appropriate for indoor laboratory equipment, commercial instrumentation and room-temperature industrial cabinets. If the design must survive extended temperature extremes, the extended-grade member of the same converter family, the ADS574KE, is rated from -40 °C to +85 °C and shares the identical 28-pin DIP footprint and pinout, so it is a direct substitution where temperature margin is needed.
Where can I download the ADS574JH datasheet PDF?
The manufacturer datasheet PDF for the ADS574 and its family members is published on the Texas Instruments product page, and a mirrored PDF listing is available through electronic component documentation portals. The datasheet contains the complete 28-pin pin configuration, the electrical characteristics table, timing diagrams for the parallel output cycle, and the recommended application circuit. Use the Texas Instruments document as the authoritative source when assigning pin functions, and always confirm the ordering-code temperature grade and package before release.
Where can I find the ADS574JH pinout?
The ADS574JH pin assignment is defined in the pin configuration table of the manufacturer datasheet, which lists all 28 terminals of the plastic DIP package, including analog input, analog and digital supply, conversion control signals, and the twelve parallel data outputs. The package drawing in the same document shows the pin-1 notch and the counter-clockwise numbering used by the DIP outline. When planning the PCB, follow that numbering sequence and route the parallel data group with matched trace lengths to keep bit-to-bit skew small.
How do I interface the ADS574JH parallel output to a microcontroller?
Connect the twelve parallel data lines to a microcontroller or FPGA data bus and read the code on the conversion-complete indication. Because no serial data clock is used, the interface stays simple: place the ADC close to the bus, keep the data lines on a single layer if possible, and route them as a matched group. Add series damping close to the driver if edge rates are fast and the bus is long, and provide local bypass capacitance on both the analog and digital supply pins.
ADS574JH vs ADS574KE - which is better for an industrial design?
The ADS574JH and the ADS574KE share the same 12-bit SAR core, the same 5 V supply, the same 40 kSPS-class throughput and the same 28-pin DIP footprint, so electrically they are interchangeable in most designs. The decisive difference is temperature grade: the ADS574JH is specified for 0 °C to +70 °C while the ADS574KE covers -40 °C to +85 °C. For indoor commercial or laboratory equipment the ADS574JH is sufficient; for cabinets near process heat, vehicle-adjacent electronics or outdoor instrumentation, choose the ADS574KE for the wider margin.
What is the difference between the ADS574JH and the ADS574JE?
Both parts belong to the same 12-bit parallel SAR converter family and share the 28-pin DIP footprint, the single 5 V supply and the 40 kSPS throughput, so they can be used on the same board layout. The distinction lies in the ordering codes: the trailing character sequence identifies the package lead style, the temperature grade and the shipment form. Choose the ADS574JH when you specifically need the commercial 0 °C to +70 °C grade in the standard DIP marking, and select the ADS574JE when your BOM specifies that exact lead code. Verify the marking on the datasheet ordering table.
When should I choose the ADS574JH over the ADS574KE?
Choose the ADS574JH when the end equipment is guaranteed to stay between 0 °C and +70 °C, such as bench-top instruments, laboratory acquisition systems or commercial indoor controllers, and when you prefer the standard commercial-grade ordering code used across new designs. Choose the ADS574KE instead when the enclosure can reach below 0 °C or above 70 °C, where the extended -40 °C to +85 °C grade provides the required margin. Both remain drop-in replacements because the footprint and pinout are identical.
Is the ADS574JH suitable for motor control and current sensing applications?
The ADS574JH is well suited to motor control front ends that measure low-bandwidth quantities such as phase current, DC link voltage or position feedback. Its 40 kSPS throughput is ample for current loops running at tens of kilohertz, the fixed SAR conversion latency keeps sampling predictable relative to the PWM cycle, and the parallel output delivers the code without serial-clock overhead. Keep the analog front end short, reference the converter closely to the amplifier chain, and synchronise the sample instant to a defined point in the switching cycle.
What is the best drop-in replacement for the ADS574JH?
The best drop-in replacement is another member of the ADS574 converter family in the 28-pin DIP package, most commonly the ADS574KE when a wider temperature range is wanted or the ADS574JE, ADS574JG and ADS574JP when the alternate ordering codes satisfy your assembly and documentation requirements. Each of these shares the 12-bit SAR architecture, the 5 V supply and the 28-pin through-hole footprint, so no board changes are required. Confirm the exact pinout and electrical table in the manufacturer datasheet before substituting.
Can the ADS574KE replace the ADS574JH on an existing board?
Yes, the ADS574KE can replace the ADS574JH on an existing board because both use the identical 28-pin plastic DIP footprint and the same 12-bit parallel SAR converter architecture operated from a single 5 V supply. The only behavioural change is the temperature rating, which widens from 0 °C to +70 °C on the ADS574JH to -40 °C to +85 °C on the ADS574KE, so the substitution never narrows your design margin. Verify lead dimensions and the pinout table against the manufacturer datasheet.
Where can I buy the ADS574JH online?
The ADS574JH is stocked by several authorised electronics distributors and is also catalogued as a Burr-Brown Corporation legacy part. Because availability for older through-hole converters varies by volume, submit a Request a Quote through the form on this page with your required part number, quantity, and target date. The XAIPART team will confirm stock position, package form and shipment configuration for the exact ordering code you need.
What is the price of the ADS574JH?
Pricing for the ADS574JH varies with volume, package form and market conditions, and the live figure is shown on this page through the Request a Quote form. Use the quote form to receive current unit pricing for your exact quantity and delivery schedule, along with the applicable order multiples. Legacy 12-bit parallel converter pricing can move quickly, so requesting a written quote is the most reliable way to lock in both price and availability for a production build.
What is the lead time for the ADS574JH?
Lead time for the ADS574JH depends on the manufacturer packaging option and the quantity you need, and it is quoted per request rather than published as a fixed figure. Submit a Request a Quote through the form on this page with your required quantity, shipment form and delivery date, and the team will confirm the current lead time along with the supporting stock position. For scheduled production, ask for the delivery schedule against your build window rather than a generic stock quantity.
What can replace the ADS574JH?
The ADS574JH can be replaced by other members of the same Texas Instruments ADS574 parallel SAR converter family in the 28-pin DIP package, such as the ADS574KE, ADS574JE, ADS574JG, ADS574JP and ADS574KG, all of which share the 12-bit resolution, the 5 V single supply and the parallel output bus. The choice comes down to the temperature grade and the ordering code that matches your assembly documentation. Cross-manufacturer parts with the same parallel 12-bit interface in a DIP-28 footprint are rare, so a footprint-compatible substitution typically means verifying the datasheet pinout carefully.
Is the ADS574JH the same as the ADS574JE?
The ADS574JH and the ADS574JE are electrically the same 12-bit parallel SAR converter from the same family, with the same 5 V supply, the same commercial 0 °C to +70 °C grade and the same 28-pin DIP footprint. They differ in the trailing ordering characters, which identify lead style, package marking and shipment form. Treat them as interchangeable in most designs, but confirm the exact ordering code required by your mechanical drawing and purchasing documentation before substitution.
What are the key specifications of the ADS574JH that engineers should know?
The ADS574JH is a 12-bit, single-channel, parallel-output successive-approximation ADC rated at 40 kSPS from a single 5 V supply, packaged in a 28-pin plastic DIP and specified over 0 °C to +70 °C. Key engineering points: the conversion latency is fixed, so sample timing can be scheduled against a control cycle; the twelve data lines require matched routing to control skew; and the through-hole footprint supports socketed prototyping and straightforward field replacement in legacy instrumentation.
What is the best alternative to the ADS574JH from another manufacturer?
For a true drop-in replacement, same-family converters such as the ADS574KE, ADS574JE, ADS574JG, ADS574JP and ADS574KG remain the most reliable choice because they preserve the 28-pin DIP footprint, the 12-bit parallel interface and the 5 V supply. A different manufacturer offers a comparable function but usually a different interface or package, such as a serial-output SAR converter, which would require a footprint and firmware change rather than a substitution. If cross-manufacturer sourcing is a priority, request a quote with the electrical requirements so the engineering team can check the closest available option.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADS574JH — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ADS574JH when your design needs a 12-bit, 40 kSPS parallel-output SAR converter in a 28-pin through-hole DIP, running from a single 5 V supply, with operation guaranteed between 0 °C and +70 °C. It is the natural choice for laboratory instruments, industrial monitoring modules, motor feedback front ends and legacy equipment retrofits where a socketed DIP part and a direct bus interface matter more than extreme temperature margin.

Pick the ADS574KE or ADS574KG instead when the enclosure temperature can exceed +70 °C or fall below 0 °C; both keep the identical footprint, electrical architecture and pinout, so the substitution is drop-in and simply widens the margin. Choose the ADS574JE, ADS574JG or ADS574JP when your mechanical drawing, BOM standard or approved-vendor list specifies that particular lead and ordering code, since they share the same commercial-grade 0 °C to +70 °C specification.

For designs that need more than 12 bits of resolution, a serial interface, or a smaller surface-mount footprint, treat the ADS574JH as a transitional choice and evaluate a modern converter family instead, because that move requires a board redesign rather than a component swap.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ADS574KE ADS574JE ADS574JG ADS574JP ADS574KG
Resolution 12 bit 12 bit 12 bit 12 bit 12 bit 12 bit
Conversion Throughput 40 kSPS 40 kSPS 40 kSPS 40 kSPS 40 kSPS 40 kSPS
Architecture Successive approximation (SAR) Successive approximation (SAR) Successive approximation (SAR) Successive approximation (SAR) Successive approximation (SAR) Successive approximation (SAR)
Output Interface Parallel, 12-bit data bus Parallel, 12-bit data bus Parallel, 12-bit data bus Parallel, 12-bit data bus Parallel, 12-bit data bus Parallel, 12-bit data bus
Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Operating Temperature Range 0 °C to +70 °C -40 °C to +85 °C 0 °C to +70 °C 0 °C to +70 °C 0 °C to +70 °C -40 °C to +85 °C
Package 28-pin plastic DIP (through-hole) 28-pin plastic DIP (through-hole) 28-pin plastic DIP (through-hole) 28-pin plastic DIP (through-hole) 28-pin plastic DIP (through-hole) 28-pin plastic DIP (through-hole)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Terminals 28 28 28 28 28 28
Temperature Grade Commercial Extended (AEC-style industrial handling not specified) Commercial Commercial Commercial Extended

মূল পার্থক্যসমূহ

  • Parallel 12-bit output removes serial-clock overhead in the control loop (বনামADS574KE)
  • Deterministic fixed-latency conversion for synchronised sampling (বনামADS574JE)
  • Legacy-friendly 28-pin through-hole DIP simplifies refurbishment (বনামADS574JG)
  • Commercial-grade option keeps supply chain simpler for indoor designs (বনামADS574KG)

ডিজাইন নোট

Route the twelve parallel data lines as a matched-length group so that bit-to-bit skew stays small relative to the latch strobe. Keep the group on a single PCB layer where possible, avoid routing it over a switching node or a high-current return path, and add a series damping resistor close to the driver if trace lengths exceed roughly 10 cm. Place the latch or capture register within a few centimetres of the converter so the parallel bus does not act as an unintended antenna during high di/dt switching.

Decouple the analog supply with a 100 nF ceramic capacitor placed directly at the device supply pins, and add a 1 uF to 10 uF bulk capacitor on the same rail close to the package. The 5 V analog rail should be filtered separately from the digital switching supply, with the analog return tied to the converter ground at a single point near the device. Keeping switching ripple off the analog rail prevents code noise from appearing in the converted result, which matters most when the input signal is close to the 1 LSB level.

The parallel output means the sampling instant and the read instant are separate events, so do not read the data bus before the conversion-complete indication and do not change the input source while a conversion is in progress. Also remember that the source impedance in front of the sample-and-hold input adds acquisition error at 40 kSPS; use a low-impedance buffer if the driving source cannot settle within the available conversion window. Finally, confirm the lead dimensions and pin numbering against the manufacturer datasheet before inserting a substitute into a socketed board.

Estimated: with a 5 V single supply and a 12-bit code near mid-scale, the average power dissipation is typically on the order of tens of milliwatts, and the 28-pin plastic DIP presents a large thermal mass compared with small surface-mount packages. With a junction-to-ambient resistance in the tens of °C/W, the temperature rise at this power level stays small, so a heatsink is not required. Keep the device away from adjacent hot regulators and provide copper around the DIP pins to improve heat spreading in dense legacy boards.

কমপ্লায়েন্স তথ্য

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

RoHS compliance is indicated on the distributor product listing for this part. The remaining environmental and substance declarations are not stated on the manufacturer listing and are therefore recorded as unknown.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

ADS574JH ADS574JH datasheet ADS574JH datasheet pdf ADS574JH pinout ADS574JH pin configuration ADS574JH equivalent ADS574JH replacement ADS574JH drop-in substitute ADS574 vs ADS574KE ADS574JH 12 bit parallel ADC ADS574JH 40 kSPS 5V 28-pin DIP SAR ADC 40 kSPS Texas Instruments ADS574JH ADS574JH price ADS574JH stock and lead time ADS574JH motor current sensing application

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments Burr-Brown Corporation ADS574JH ADS574 ADS574KE ADS574JE ADS574JG ADS574JP ADS574KG analog-to-digital converter ADC successive approximation SAR parallel output ADC single-channel ADC data converter mixed-signal integrated circuit 12-bit resolution 40 kSPS throughput 5 V single supply 1 LSB DIP-28 plastic DIP through-hole package commercial temperature grade RoHS motor control industrial instrumentation fixed conversion latency sample-and-hold
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন