ADS574JH - 12-Bit 40 kSPS Parallel SAR ADC, 28-Pin DIP | Texas Instruments
料号: ADS574JH ✓ 量产中ADS574JH 概述
An SAR ADC is one of the two dominant ADC architectures, alongside flash and delta-sigma converters. Each conversion cycle applies a sequence of internal comparator trials, resolving the analog input into a digital code in a fixed, deterministic number of clock periods. Because the conversion time is fixed and independent of input voltage, SAR converters deliver deterministic latency with no pipeline fill, and they are typically preferred wherever a sampled measurement must line up predictably with a control or comms cycle.
Key features of the ADS574JH include 12-bit resolution, single-channel conversion at 40 kSPS, a parallel digital output that transfers the complete code directly into a bus without serial clocking, operation from a single 5 V supply, and a 28-pin through-hole DIP footprint that simplifies both prototyping and legacy instrument refurbishment.
Technically, the device belongs to the classic ADS57x family of parallel-output SAR converters originally introduced by Burr-Brown and now supported by Texas Instruments. The parallel interface removes the need for a serial data clock, so the 12 output lines can be wired straight into a microcontroller data bus, an FPGA capture register, or a latch. Throughput of 40 kSPS is generous for slow industrial and motor-control variables such as shaft position, current feedback, or temperature, and the DIP package keeps the part attractive for designs where surface-mount assembly is not practical.
Typical uses include brushless DC and servo motor phase-current sensing, industrial pressure and level instrumentation, laboratory data acquisition, and position-feedback decoding in printers and robotics.
Designers should pay attention to three points: route the 12 parallel data lines as a matched-length group to avoid skew between bit lines, place the analog supply bypass capacitors directly at the device pins, and allow the full settling period between conversions if the source impedance is high.
This page consolidates manufacturer specifications, package and grade details, drop-in alternatives from the same converter family, and practical interface guidance into a single engineering reference for engineers evaluating legacy 12-bit parallel SAR converters.
直接替换替代料: ADS574JH ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADS574JH (相同外形与封装尺寸) ——差异在于 Package, Supply Voltage, Mounting Type, Microprocessor Interface, RoHS Status.
ADS574KE
✅ 直接替换联系询价
查看数据手册 →ADS574JE
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →ADS574JG
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ADS574JP
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →ADS574KG
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
ADS574JH 最大额定值与电气特性
| ADC Type | Successive approximation (SAR), single-channel |
| 分辨率 | 12 bit |
| Conversion Throughput | 40 kSPS |
| Output Interface | Parallel, 12-bit digital output bus |
| 电源电压 | 5 V |
| Number of Channels | 1 |
| Resolution Step | 1 LSB |
| 封装 | 28-pin plastic DIP (through-hole) |
| Package Code | DIP, rectangular |
| Number of Terminals | 28 |
| Terminal Form | Through-hole |
| 安装类型 | Through-hole (THT) |
| Temperature Grade | Commercial |
| 工作温度范围 | 0 °C to +70 °C |
| RoHS 状态 | Compliant (per distributor product listing) |
ADS574JH dip, rectangular 引脚配置指南
ADS574JH(dip, rectangular 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS574JH.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS574JH 适用于 6 应用s: Motor Phase-Current Sensing, Industrial Pressure and Level Instrumentation, Laboratory Data Acquisition and Instrumentation, Position and Encoder Feedback Decoding, Power Supply and Inverter Monitoring, Legacy Test Equipment and Line Retrofits.
Motor Phase-Current Sensing
The ADS574JH suits brushless DC and servo drive front ends that digitise low-bandwidth phase current or DC-link voltage for the control loop. A conversion throughput of 40 kSPS is comfortably above the tens of kilohertz current-loop bandwidth typical of industrial drives, and the fixed SAR conversion latency lets the sample instant be scheduled against a defined point in the PWM cycle. The 12 parallel data lines connect straight to the controller bus without a serial data clock, shortening the feedback path. Place the converter adjacent to the current-sense amplifier and reference it to the same analog ground so the 12-bit code remains meaningful at small shunt voltages.
推荐
Industrial Pressure and Level Instrumentation
Process instrumentation built around resistive or capacitive transducers commonly needs a compact, deterministic converter for slow-changing analog signals. The ADS574JH provides 12-bit resolution at 40 kSPS in a 28-pin plastic DIP, a package that is easy to socket for field serviceable transmitters. Because SAR conversion time is fixed and independent of input level, the instrument controller can run deterministic sampling intervals and apply digital linearisation and temperature compensation without variable latency artefacts. The single 5 V supply also simplifies power budgeting in transmitters that already regulate a 5 V rail from an isolated converter.
推荐
Laboratory Data Acquisition and Instrumentation
Bench instruments that capture slow analog waveforms, calibration tables or transducer outputs benefit from the deterministic behaviour and simple hookup of a parallel-output SAR converter. The ADS574JH drives its 12-bit code directly onto a data bus, so a microcontroller can latch the value on the conversion-complete signal and forward it over USB or Ethernet without bit-serialisation firmware. The 40 kSPS ceiling supports sampling of thermal, pressure and position channels at rates well above the underlying mechanical bandwidths, and the through-hole DIP package allows socketed replacement on long-lived laboratory hardware.
推荐
Position and Encoder Feedback Decoding
Incremental encoder counters, linear position transducers and servo feedback loops need a converter whose sampling delay is predictable so that position estimates align with the mechanical reference. The ADS574JH resolves each sample in a fixed number of clock periods at up to 40 kSPS, giving the controller a deterministic latency budget for interpolation and filtering. The 12-bit parallel output avoids the serial clocking overhead that limits the update rate of many serial-interface converters. Keep the analog input path short and shielded, and synchronise the sample command to the encoder index pulse to avoid ambiguity near a count rollover.
推荐
Power Supply and Inverter Monitoring
Inverters, battery management controllers and power quality analysers routinely digitise bus voltages, output currents and temperature probes for supervisory functions rather than for high-bandwidth control loops. The ADS574JH is appropriate for these supervisory channels because 40 kSPS is far above the required update rate and the 12-bit code is ample for metering and protection thresholds. Its parallel output bus shares the same 5 V supply domain as most controller logic, simplifying level considerations, while the DIP package remains easy to socket in field-replaceable power modules. Provide local bulk and ceramic decoupling close to the analog supply pins to keep switching-node ripple off the reference.
推荐
Legacy Test Equipment and Line Retrofits
Refurbishing bench instruments, panel meters and production test fixtures often requires replacing a through-hole parallel converter rather than re-laying out a mixed-signal board. The ADS574JH in a 28-pin plastic DIP allows a direct socket-level or footprint-level swap in equipment designed around the original parallel 12-bit interface, avoiding the schematic, layout and firmware rework that a serial-interface replacement would demand. Its commercial 0 °C to +70 °C rating suits indoor factory and laboratory environments. When selecting a substitute for a wider temperature window, the extended-grade member of the same family shares the identical pinout and lead dimensions.
推荐
推荐产品汇总
工程参考数据: ADS574JH ——对比、设计指导和合规信息。
选型指南
Pick the ADS574KE or ADS574KG instead when the enclosure temperature can exceed +70 °C or fall below 0 °C; both keep the identical footprint, electrical architecture and pinout, so the substitution is drop-in and simply widens the margin. Choose the ADS574JE, ADS574JG or ADS574JP when your mechanical drawing, BOM standard or approved-vendor list specifies that particular lead and ordering code, since they share the same commercial-grade 0 °C to +70 °C specification.
For designs that need more than 12 bits of resolution, a serial interface, or a smaller surface-mount footprint, treat the ADS574JH as a transitional choice and evaluate a modern converter family instead, because that move requires a board redesign rather than a component swap.
与替代料对比
| 参数 | 本产品 | ADS574KE | ADS574JE | ADS574JG | ADS574JP | ADS574KG |
|---|---|---|---|---|---|---|
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Conversion Throughput | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Output Interface | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Operating Temperature Range | 0 °C to +70 °C | -40 °C to +85 °C | 0 °C to +70 °C | 0 °C to +70 °C | 0 °C to +70 °C | -40 °C to +85 °C |
| Package | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Terminals | 28 | 28 | 28 | 28 | 28 | 28 |
| Temperature Grade | Commercial | Extended (AEC-style industrial handling not specified) | Commercial | Commercial | Commercial | Extended |
关键差异点
- Parallel 12-bit output removes serial-clock overhead in the control loop (对比 ADS574KE)
- Deterministic fixed-latency conversion for synchronised sampling (对比 ADS574JE)
- Legacy-friendly 28-pin through-hole DIP simplifies refurbishment (对比 ADS574JG)
- Commercial-grade option keeps supply chain simpler for indoor designs (对比 ADS574KG)
设计说明
Route the twelve parallel data lines as a matched-length group so that bit-to-bit skew stays small relative to the latch strobe. Keep the group on a single PCB layer where possible, avoid routing it over a switching node or a high-current return path, and add a series damping resistor close to the driver if trace lengths exceed roughly 10 cm. Place the latch or capture register within a few centimetres of the converter so the parallel bus does not act as an unintended antenna during high di/dt switching.
Decouple the analog supply with a 100 nF ceramic capacitor placed directly at the device supply pins, and add a 1 uF to 10 uF bulk capacitor on the same rail close to the package. The 5 V analog rail should be filtered separately from the digital switching supply, with the analog return tied to the converter ground at a single point near the device. Keeping switching ripple off the analog rail prevents code noise from appearing in the converted result, which matters most when the input signal is close to the 1 LSB level.
The parallel output means the sampling instant and the read instant are separate events, so do not read the data bus before the conversion-complete indication and do not change the input source while a conversion is in progress. Also remember that the source impedance in front of the sample-and-hold input adds acquisition error at 40 kSPS; use a low-impedance buffer if the driving source cannot settle within the available conversion window. Finally, confirm the lead dimensions and pin numbering against the manufacturer datasheet before inserting a substitute into a socketed board.
Estimated: with a 5 V single supply and a 12-bit code near mid-scale, the average power dissipation is typically on the order of tens of milliwatts, and the 28-pin plastic DIP presents a large thermal mass compared with small surface-mount packages. With a junction-to-ambient resistance in the tens of °C/W, the temperature rise at this power level stays small, so a heatsink is not required. Keep the device away from adjacent hot regulators and provide copper around the DIP pins to improve heat spreading in dense legacy boards.
合规信息
RoHS compliance is indicated on the distributor product listing for this part. The remaining environmental and substance declarations are not stated on the manufacturer listing and are therefore recorded as unknown.