ADS574JH - 12-Bit 40 kSPS Parallel SAR ADC, 28-Pin DIP | Texas Instruments
MPN: ADS574JH ✓ Hoạt độngADS574JH Tóm tắt
An SAR ADC is one of the two dominant ADC architectures, alongside flash and delta-sigma converters. Each conversion cycle applies a sequence of internal comparator trials, resolving the analog input into a digital code in a fixed, deterministic number of clock periods. Because the conversion time is fixed and independent of input voltage, SAR converters deliver deterministic latency with no pipeline fill, and they are typically preferred wherever a sampled measurement must line up predictably with a control or comms cycle.
Key features of the ADS574JH include 12-bit resolution, single-channel conversion at 40 kSPS, a parallel digital output that transfers the complete code directly into a bus without serial clocking, operation from a single 5 V supply, and a 28-pin through-hole DIP footprint that simplifies both prototyping and legacy instrument refurbishment.
Technically, the device belongs to the classic ADS57x family of parallel-output SAR converters originally introduced by Burr-Brown and now supported by Texas Instruments. The parallel interface removes the need for a serial data clock, so the 12 output lines can be wired straight into a microcontroller data bus, an FPGA capture register, or a latch. Throughput of 40 kSPS is generous for slow industrial and motor-control variables such as shaft position, current feedback, or temperature, and the DIP package keeps the part attractive for designs where surface-mount assembly is not practical.
Typical uses include brushless DC and servo motor phase-current sensing, industrial pressure and level instrumentation, laboratory data acquisition, and position-feedback decoding in printers and robotics.
Designers should pay attention to three points: route the 12 parallel data lines as a matched-length group to avoid skew between bit lines, place the analog supply bypass capacitors directly at the device pins, and allow the full settling period between conversions if the source impedance is high.
This page consolidates manufacturer specifications, package and grade details, drop-in alternatives from the same converter family, and practical interface guidance into a single engineering reference for engineers evaluating legacy 12-bit parallel SAR converters.
Bộ thay thế dễ dàng lắp đặt cho ADS574JH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADS574JH (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage, Mounting Type, Microprocessor Interface, RoHS Status.
ADS574KE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADS574JE
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ADS574JG
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADS574JP
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ADS574KG
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADS574JH Tỷ lệ tối đa & tính chất điện
| ADC Type | Successive approximation (SAR), single-channel |
| Độ phân giải | 12 bit |
| Conversion Throughput | 40 kSPS |
| Output Interface | Parallel, 12-bit digital output bus |
| Điện áp cung cấp | 5 V |
| Number of Channels | 1 |
| Resolution Step | 1 LSB |
| Hộp | 28-pin plastic DIP (through-hole) |
| Package Code | DIP, rectangular |
| Number of Terminals | 28 |
| Terminal Form | Through-hole |
| Kiểu lắp đặt | Through-hole (THT) |
| Temperature Grade | Commercial |
| Khoảng nhiệt độ hoạt động | 0 °C to +70 °C |
| Trạng thái RoHS | Compliant (per distributor product listing) |
Hướng dẫn cấu hình chân ADS574JH dip, rectangular
Cấu hình chân cho ADS574JH (dip, rectangular gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho ADS574JH.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADS574JH phù hợp cho 6 Áp dụngs: Motor Phase-Current Sensing, Industrial Pressure and Level Instrumentation, Laboratory Data Acquisition and Instrumentation, Position and Encoder Feedback Decoding, Power Supply and Inverter Monitoring, Legacy Test Equipment and Line Retrofits.
Motor Phase-Current Sensing
The ADS574JH suits brushless DC and servo drive front ends that digitise low-bandwidth phase current or DC-link voltage for the control loop. A conversion throughput of 40 kSPS is comfortably above the tens of kilohertz current-loop bandwidth typical of industrial drives, and the fixed SAR conversion latency lets the sample instant be scheduled against a defined point in the PWM cycle. The 12 parallel data lines connect straight to the controller bus without a serial data clock, shortening the feedback path. Place the converter adjacent to the current-sense amplifier and reference it to the same analog ground so the 12-bit code remains meaningful at small shunt voltages.
Được đề xuất
Industrial Pressure and Level Instrumentation
Process instrumentation built around resistive or capacitive transducers commonly needs a compact, deterministic converter for slow-changing analog signals. The ADS574JH provides 12-bit resolution at 40 kSPS in a 28-pin plastic DIP, a package that is easy to socket for field serviceable transmitters. Because SAR conversion time is fixed and independent of input level, the instrument controller can run deterministic sampling intervals and apply digital linearisation and temperature compensation without variable latency artefacts. The single 5 V supply also simplifies power budgeting in transmitters that already regulate a 5 V rail from an isolated converter.
Được đề xuất
Laboratory Data Acquisition and Instrumentation
Bench instruments that capture slow analog waveforms, calibration tables or transducer outputs benefit from the deterministic behaviour and simple hookup of a parallel-output SAR converter. The ADS574JH drives its 12-bit code directly onto a data bus, so a microcontroller can latch the value on the conversion-complete signal and forward it over USB or Ethernet without bit-serialisation firmware. The 40 kSPS ceiling supports sampling of thermal, pressure and position channels at rates well above the underlying mechanical bandwidths, and the through-hole DIP package allows socketed replacement on long-lived laboratory hardware.
Được đề xuất
Position and Encoder Feedback Decoding
Incremental encoder counters, linear position transducers and servo feedback loops need a converter whose sampling delay is predictable so that position estimates align with the mechanical reference. The ADS574JH resolves each sample in a fixed number of clock periods at up to 40 kSPS, giving the controller a deterministic latency budget for interpolation and filtering. The 12-bit parallel output avoids the serial clocking overhead that limits the update rate of many serial-interface converters. Keep the analog input path short and shielded, and synchronise the sample command to the encoder index pulse to avoid ambiguity near a count rollover.
Được đề xuất
Power Supply and Inverter Monitoring
Inverters, battery management controllers and power quality analysers routinely digitise bus voltages, output currents and temperature probes for supervisory functions rather than for high-bandwidth control loops. The ADS574JH is appropriate for these supervisory channels because 40 kSPS is far above the required update rate and the 12-bit code is ample for metering and protection thresholds. Its parallel output bus shares the same 5 V supply domain as most controller logic, simplifying level considerations, while the DIP package remains easy to socket in field-replaceable power modules. Provide local bulk and ceramic decoupling close to the analog supply pins to keep switching-node ripple off the reference.
Được đề xuất
Legacy Test Equipment and Line Retrofits
Refurbishing bench instruments, panel meters and production test fixtures often requires replacing a through-hole parallel converter rather than re-laying out a mixed-signal board. The ADS574JH in a 28-pin plastic DIP allows a direct socket-level or footprint-level swap in equipment designed around the original parallel 12-bit interface, avoiding the schematic, layout and firmware rework that a serial-interface replacement would demand. Its commercial 0 °C to +70 °C rating suits indoor factory and laboratory environments. When selecting a substitute for a wider temperature window, the extended-grade member of the same family shares the identical pinout and lead dimensions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADS574JH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Pick the ADS574KE or ADS574KG instead when the enclosure temperature can exceed +70 °C or fall below 0 °C; both keep the identical footprint, electrical architecture and pinout, so the substitution is drop-in and simply widens the margin. Choose the ADS574JE, ADS574JG or ADS574JP when your mechanical drawing, BOM standard or approved-vendor list specifies that particular lead and ordering code, since they share the same commercial-grade 0 °C to +70 °C specification.
For designs that need more than 12 bits of resolution, a serial interface, or a smaller surface-mount footprint, treat the ADS574JH as a transitional choice and evaluate a modern converter family instead, because that move requires a board redesign rather than a component swap.
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADS574KE | ADS574JE | ADS574JG | ADS574JP | ADS574KG |
|---|---|---|---|---|---|---|
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Conversion Throughput | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS | 40 kSPS |
| Architecture | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Output Interface | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus | Parallel, 12-bit data bus |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Operating Temperature Range | 0 °C to +70 °C | -40 °C to +85 °C | 0 °C to +70 °C | 0 °C to +70 °C | 0 °C to +70 °C | -40 °C to +85 °C |
| Package | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) | 28-pin plastic DIP (through-hole) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Terminals | 28 | 28 | 28 | 28 | 28 | 28 |
| Temperature Grade | Commercial | Extended (AEC-style industrial handling not specified) | Commercial | Commercial | Commercial | Extended |
Bảo phân biệt quan trọng
- Parallel 12-bit output removes serial-clock overhead in the control loop (vsADS574KE)
- Deterministic fixed-latency conversion for synchronised sampling (vsADS574JE)
- Legacy-friendly 28-pin through-hole DIP simplifies refurbishment (vsADS574JG)
- Commercial-grade option keeps supply chain simpler for indoor designs (vsADS574KG)
Ghi chú thiết kế
Route the twelve parallel data lines as a matched-length group so that bit-to-bit skew stays small relative to the latch strobe. Keep the group on a single PCB layer where possible, avoid routing it over a switching node or a high-current return path, and add a series damping resistor close to the driver if trace lengths exceed roughly 10 cm. Place the latch or capture register within a few centimetres of the converter so the parallel bus does not act as an unintended antenna during high di/dt switching.
Decouple the analog supply with a 100 nF ceramic capacitor placed directly at the device supply pins, and add a 1 uF to 10 uF bulk capacitor on the same rail close to the package. The 5 V analog rail should be filtered separately from the digital switching supply, with the analog return tied to the converter ground at a single point near the device. Keeping switching ripple off the analog rail prevents code noise from appearing in the converted result, which matters most when the input signal is close to the 1 LSB level.
The parallel output means the sampling instant and the read instant are separate events, so do not read the data bus before the conversion-complete indication and do not change the input source while a conversion is in progress. Also remember that the source impedance in front of the sample-and-hold input adds acquisition error at 40 kSPS; use a low-impedance buffer if the driving source cannot settle within the available conversion window. Finally, confirm the lead dimensions and pin numbering against the manufacturer datasheet before inserting a substitute into a socketed board.
Estimated: with a 5 V single supply and a 12-bit code near mid-scale, the average power dissipation is typically on the order of tens of milliwatts, and the 28-pin plastic DIP presents a large thermal mass compared with small surface-mount packages. With a junction-to-ambient resistance in the tens of °C/W, the temperature rise at this power level stays small, so a heatsink is not required. Keep the device away from adjacent hot regulators and provide copper around the DIP pins to improve heat spreading in dense legacy boards.
Thông tin tuân thủ
RoHS compliance is indicated on the distributor product listing for this part. The remaining environmental and substance declarations are not stated on the manufacturer listing and are therefore recorded as unknown.