ATSAML10E16A-AF - 32MHz Cortex-M23 MCU | Microchip
MPN: ATSAML10E16A-AF ✓ সক্রিয়ATSAML10E16A-AF সারাংশ
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ATSAML10E16A belongs to the SAM L10 family and combines the Arm Cortex-M23 core with embedded flash, SRAM, serial interfaces, timing resources, and low-power peripherals. Its position in the hierarchy is microcontroller, embedded processor, semiconductor, and system-on-chip component for compact control systems.
The principal features include an operating frequency of 32 MHz, 64 KB of flash, 16 KB of SRAM, and 25 I/O in the 32-pin TQFP configuration. Microchip specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. The device also includes an enhanced peripheral touch controller, advanced analog resources, an ISO7816 smart-card interface, and an event system for coordinating peripheral activity.
The Arm Cortex-M23 core provides a 32-bit instruction set while maintaining a compact, power-conscious architecture suited to battery-operated equipment. Hardware-enforced TrustZone security domains can separate secure and non-secure software when the complete device configuration and development environment support them. Peripheral integration reduces the need for external sensors, analog converters, and communication controllers on small embedded boards.
Typical uses include capacitive-touch user interfaces, smart-card readers, low-power sensor nodes, compact industrial controllers, and connected security accessories. The enhanced touch controller is useful when a PCB overlay, keypad, or proximity surface must be scanned without a dedicated external controller. The ISO7816 interface supports smart-card communication designs, while the advanced analog section can reduce external signal-conditioning requirements.
Board design should preserve access to programming and debug functions, route sensitive analog and touch inputs away from fast digital signals, and provide the decoupling required by the Microchip device documentation. Confirm the exact pin functions, programming workflow, and external-component requirements against the manufacturer datasheet before committing a 7 x 7 mm TQFP layout to production.
This product page consolidates the principal processor, memory, package, low-power, analog, touch, and smart-card characteristics with practical design guidance, structured comparisons, and sourcing information for engineers evaluating the ATSAML10E16A-AF for compact embedded systems.
এর জন্য ড্রপ-ইন বিকল্প ATSAML10E16A-AF — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible ATSAML10E16A-AF (একই form factor এবং footprint) — পার্থক্য রয়েছে Core Architecture, Package, ADC, Active Mode Current, RoHS Status.
ATSAML10E16A-MFT
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
ATSAML10E16A-AF সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M23 |
| Core Architecture | Armv8-M |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 64 KB |
| SRAM | 16 KB |
| I/O Count | 25 I/O |
| প্যাকেজ | 32-pin TQFP, 7 x 7 mm |
| মাউন্টিং টাইপ | Surface mount |
| Active Mode Current | Less than 25 uA/MHz |
| Sleep Mode Current | Less than 100 nA |
| Maximum Temperature | 125 °C |
| Green Status | Green |
| Shipping Format | Tray |
| Touch Support | Enhanced peripheral touch controller |
| Analog Support | Advanced analog peripherals |
| Smart-Card Interface | ISO7816 interface |
| Event System | Event system |
ATSAML10E16A-AF 32-pin tqfp, 7 x 7 mm পিন কনফিগারেশন গাইড
ATSAML10E16A-AF (32-pin tqfp, 7 x 7 mm প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ATSAML10E16A-AF.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ATSAML10E16A-AF এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Capacitive-Touch User Interfaces, Smart-Card Readers and Access Controls, Battery-Powered Sensor Nodes, Compact Industrial Controllers, Low-Power Wearable Accessories, Secure Embedded Accessories.
Capacitive-Touch User Interfaces
The ATSAML10E16A-AF fits compact touch controls because its enhanced peripheral touch controller is integrated with a 32 MHz Arm Cortex-M23 core and 25 I/O in the 32-pin TQFP package. A firmware-based controller can scan touch electrodes, apply filtering, and drive indicators without requiring a separate touch-controller IC. The 64 KB of flash and 16 KB of SRAM provide room for interface firmware, event handling, and local state. Designers should validate electrode geometry, acquisition timing, grounding, and noise immunity against the Microchip application guidance, particularly when touch traces run near switching power circuitry.
সুপারিশকৃত
Smart-Card Readers and Access Controls
The ATSAML10E16A-AF is suitable for smart-card access equipment because the SAM L10 family includes an ISO7816 smart-card interface alongside its 32 MHz Cortex-M23 processor. Designers can use the same device for protocol handling, card-presence detection, user-interface logic, and low-power standby control. Its less-than-100-nA sleep specification supports designs that spend most of their time waiting for a card or user event. Firmware must manage the external card interface, electrical levels, timing, security state, and secure boot requirements according to the manufacturer documentation.
সুপারিশকৃত
Battery-Powered Sensor Nodes
The ATSAML10E16A-AF supports battery-powered sensor nodes that alternate between periodic measurements and long inactive intervals. Its 32 MHz Cortex-M23 core provides enough performance for local filtering, event logic, and communication framing, while the 64 KB flash and 16 KB SRAM avoid external memory in many designs. Microchip specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode, allowing the system designer to balance processing time against battery capacity. Select an external low-power sensor only when the integrated analog resources cannot meet the required measurement accuracy or sampling rate.
সুপারিশকৃত
Compact Industrial Controllers
The ATSAML10E16A-AF fits compact industrial controllers that require deterministic embedded control, local I/O, and low standby consumption. Its 32-bit Cortex-M23 core runs at 32 MHz, while the 25 available I/O and advanced analog peripherals can connect sensors, actuators, status indicators, and service interfaces. The 32-pin TQFP footprint supports compact, standardized assemblies without forcing a fine-pitch package. For factory equipment, validate timing margins, input levels, isolation strategy, temperature behavior, and firmware update requirements; consumer compliance markings should not be treated as industrial qualification.
সুপারিশকৃত
Low-Power Wearable Accessories
The ATSAML10E16A-AF can serve as the control center for a small wearable accessory that uses touch input, event processing, and intermittent wireless activity. The less-than-25-uA/MHz active specification supports duty-cycled operation, and the less-than-100-nA sleep figure helps preserve battery life when the product is idle. With 64 KB of flash, 16 KB of SRAM, and integrated touch support, the MCU can consolidate several discrete functions into one device. Battery-current budgeting should include the selected radio and sensors, because their consumption may dominate the controller and determine the useful duty cycle.
সুপারিশকৃত
Secure Embedded Accessories
The ATSAML10E16A-AF is appropriate for connected accessories that benefit from isolated secure and non-secure software domains. The Cortex-M23 core includes hardware-enforced TrustZone capabilities, while the device's low-power operating characteristics support always-on accessory designs. Its 32-bit processing at 32 MHz can handle communication setup, local policy checks, user input, and peripheral coordination. Security still depends on enabling the correct device features, protecting keys, implementing secure boot, and following Microchip's configuration guidance. The 64 KB flash and 16 KB SRAM also require disciplined partitioning between trusted code, application code, and working buffers.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ATSAML10E16A-AF — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | ATSAML10E16A-MFT |
|---|---|---|
| Package | 32-TQFP (7x7) | 32-TQFP (7x7) |
| Brand | Microchip Technology | Microchip Technology |
মূল পার্থক্যসমূহ
- Integrated touch, analog, smart-card, and event-management resources (বনামATSAML10E16A-MFT)
- Low-power operation for duty-cycled embedded products (বনামATSAML10E16A-MFT)
- Compact memory-balanced Cortex-M23 configuration (বনামATSAML10E16A-MFT)
ডিজাইন নোট
Estimated: the manufacturer specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. Calculate the controller's average current from the planned active duration, sleep duration, and operating frequency rather than using only the sleep figure. Include sensor, radio, regulator, and leakage current in the complete power budget, then confirm the selected operating point against the Microchip datasheet before setting the battery-life target.
Place the required input capacitors directly beside their associated power pins and keep the return path short. Route touch-sensing and analog signals away from switching-node and high-current traces, and use a quiet ground strategy for analog references. Because the ATSAML10E16A-AF combines sensitive analog and touch functions with digital processing in one package, component placement and return-current control can materially affect measurement repeatability and electromagnetic immunity.
Do not treat the ATSAML10E16A, ATSAML10E16A-AF, and similarly named family ordering codes as interchangeable without checking their order codes. Confirm the 32-pin TQFP dimensions, pin numbering, temperature grade, memory configuration, packing format, and product status in the Microchip documentation. A package match alone is insufficient for firmware compatibility because bootloader behavior, peripheral configuration, and device identification can vary between ordering options.
Use the manufacturer's recommended programming and debug connections and preserve access to the reset and programming interface. For analog measurements and capacitive-touch channels, follow the documented acquisition sequence and source-impedance limits. Validate settling at the intended clock speed, compare measured noise against the required signal-to-noise ratio, and keep test points and debug clocks away from sensitive touch electrodes to avoid corrupting acquisition results.
কমপ্লায়েন্স তথ্য
The catalog identifies the ATSAML10E16A-AF as green, but no separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.