ATSAML10E16A-AF - 32MHz Cortex-M23 MCU | Microchip
MPN: ATSAML10E16A-AF ✓ 啟用中ATSAML10E16A-AF 概覽
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ATSAML10E16A belongs to the SAM L10 family and combines the Arm Cortex-M23 core with embedded flash, SRAM, serial interfaces, timing resources, and low-power peripherals. Its position in the hierarchy is microcontroller, embedded processor, semiconductor, and system-on-chip component for compact control systems.
The principal features include an operating frequency of 32 MHz, 64 KB of flash, 16 KB of SRAM, and 25 I/O in the 32-pin TQFP configuration. Microchip specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. The device also includes an enhanced peripheral touch controller, advanced analog resources, an ISO7816 smart-card interface, and an event system for coordinating peripheral activity.
The Arm Cortex-M23 core provides a 32-bit instruction set while maintaining a compact, power-conscious architecture suited to battery-operated equipment. Hardware-enforced TrustZone security domains can separate secure and non-secure software when the complete device configuration and development environment support them. Peripheral integration reduces the need for external sensors, analog converters, and communication controllers on small embedded boards.
Typical uses include capacitive-touch user interfaces, smart-card readers, low-power sensor nodes, compact industrial controllers, and connected security accessories. The enhanced touch controller is useful when a PCB overlay, keypad, or proximity surface must be scanned without a dedicated external controller. The ISO7816 interface supports smart-card communication designs, while the advanced analog section can reduce external signal-conditioning requirements.
Board design should preserve access to programming and debug functions, route sensitive analog and touch inputs away from fast digital signals, and provide the decoupling required by the Microchip device documentation. Confirm the exact pin functions, programming workflow, and external-component requirements against the manufacturer datasheet before committing a 7 x 7 mm TQFP layout to production.
This product page consolidates the principal processor, memory, package, low-power, analog, touch, and smart-card characteristics with practical design guidance, structured comparisons, and sourcing information for engineers evaluating the ATSAML10E16A-AF for compact embedded systems.
直接替換替代品,適用於 ATSAML10E16A-AF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ATSAML10E16A-AF (相同外形與佔位) — 差異在於 Core Architecture, Package, ADC, Active Mode Current, RoHS Status.
ATSAML10E16A-MFT
✅ 直接替換📋 參考替代品(不在目錄中)
ATSAML10E16A-AF 最大額定值與電氣特性
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M23 |
| Core Architecture | Armv8-M |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 64 KB |
| SRAM | 16 KB |
| I/O Count | 25 I/O |
| 封裝 | 32-pin TQFP, 7 x 7 mm |
| 安裝類型 | Surface mount |
| Active Mode Current | Less than 25 uA/MHz |
| Sleep Mode Current | Less than 100 nA |
| Maximum Temperature | 125 °C |
| Green Status | Green |
| Shipping Format | Tray |
| Touch Support | Enhanced peripheral touch controller |
| Analog Support | Advanced analog peripherals |
| Smart-Card Interface | ISO7816 interface |
| Event System | Event system |
ATSAML10E16A-AF 32-pin tqfp, 7 x 7 mm 腳位配置指南
ATSAML10E16A-AF(32-pin tqfp, 7 x 7 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATSAML10E16A-AF.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATSAML10E16A-AF 適用於 6 應用s: Capacitive-Touch User Interfaces, Smart-Card Readers and Access Controls, Battery-Powered Sensor Nodes, Compact Industrial Controllers, Low-Power Wearable Accessories, Secure Embedded Accessories.
Capacitive-Touch User Interfaces
The ATSAML10E16A-AF fits compact touch controls because its enhanced peripheral touch controller is integrated with a 32 MHz Arm Cortex-M23 core and 25 I/O in the 32-pin TQFP package. A firmware-based controller can scan touch electrodes, apply filtering, and drive indicators without requiring a separate touch-controller IC. The 64 KB of flash and 16 KB of SRAM provide room for interface firmware, event handling, and local state. Designers should validate electrode geometry, acquisition timing, grounding, and noise immunity against the Microchip application guidance, particularly when touch traces run near switching power circuitry.
推薦
Smart-Card Readers and Access Controls
The ATSAML10E16A-AF is suitable for smart-card access equipment because the SAM L10 family includes an ISO7816 smart-card interface alongside its 32 MHz Cortex-M23 processor. Designers can use the same device for protocol handling, card-presence detection, user-interface logic, and low-power standby control. Its less-than-100-nA sleep specification supports designs that spend most of their time waiting for a card or user event. Firmware must manage the external card interface, electrical levels, timing, security state, and secure boot requirements according to the manufacturer documentation.
推薦
Battery-Powered Sensor Nodes
The ATSAML10E16A-AF supports battery-powered sensor nodes that alternate between periodic measurements and long inactive intervals. Its 32 MHz Cortex-M23 core provides enough performance for local filtering, event logic, and communication framing, while the 64 KB flash and 16 KB SRAM avoid external memory in many designs. Microchip specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode, allowing the system designer to balance processing time against battery capacity. Select an external low-power sensor only when the integrated analog resources cannot meet the required measurement accuracy or sampling rate.
推薦
Compact Industrial Controllers
The ATSAML10E16A-AF fits compact industrial controllers that require deterministic embedded control, local I/O, and low standby consumption. Its 32-bit Cortex-M23 core runs at 32 MHz, while the 25 available I/O and advanced analog peripherals can connect sensors, actuators, status indicators, and service interfaces. The 32-pin TQFP footprint supports compact, standardized assemblies without forcing a fine-pitch package. For factory equipment, validate timing margins, input levels, isolation strategy, temperature behavior, and firmware update requirements; consumer compliance markings should not be treated as industrial qualification.
推薦
Low-Power Wearable Accessories
The ATSAML10E16A-AF can serve as the control center for a small wearable accessory that uses touch input, event processing, and intermittent wireless activity. The less-than-25-uA/MHz active specification supports duty-cycled operation, and the less-than-100-nA sleep figure helps preserve battery life when the product is idle. With 64 KB of flash, 16 KB of SRAM, and integrated touch support, the MCU can consolidate several discrete functions into one device. Battery-current budgeting should include the selected radio and sensors, because their consumption may dominate the controller and determine the useful duty cycle.
推薦
Secure Embedded Accessories
The ATSAML10E16A-AF is appropriate for connected accessories that benefit from isolated secure and non-secure software domains. The Cortex-M23 core includes hardware-enforced TrustZone capabilities, while the device's low-power operating characteristics support always-on accessory designs. Its 32-bit processing at 32 MHz can handle communication setup, local policy checks, user input, and peripheral coordination. Security still depends on enabling the correct device features, protecting keys, implementing secure boot, and following Microchip's configuration guidance. The 64 KB flash and 16 KB SRAM also require disciplined partitioning between trusted code, application code, and working buffers.
推薦
推薦產品摘要
工程參考資料,適用於 ATSAML10E16A-AF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATSAML10E16A-MFT |
|---|---|---|
| Package | 32-TQFP (7x7) | 32-TQFP (7x7) |
| Brand | Microchip Technology | Microchip Technology |
主要差異化特點
- Integrated touch, analog, smart-card, and event-management resources (對比ATSAML10E16A-MFT)
- Low-power operation for duty-cycled embedded products (對比ATSAML10E16A-MFT)
- Compact memory-balanced Cortex-M23 configuration (對比ATSAML10E16A-MFT)
設計說明
Estimated: the manufacturer specifies less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. Calculate the controller's average current from the planned active duration, sleep duration, and operating frequency rather than using only the sleep figure. Include sensor, radio, regulator, and leakage current in the complete power budget, then confirm the selected operating point against the Microchip datasheet before setting the battery-life target.
Place the required input capacitors directly beside their associated power pins and keep the return path short. Route touch-sensing and analog signals away from switching-node and high-current traces, and use a quiet ground strategy for analog references. Because the ATSAML10E16A-AF combines sensitive analog and touch functions with digital processing in one package, component placement and return-current control can materially affect measurement repeatability and electromagnetic immunity.
Do not treat the ATSAML10E16A, ATSAML10E16A-AF, and similarly named family ordering codes as interchangeable without checking their order codes. Confirm the 32-pin TQFP dimensions, pin numbering, temperature grade, memory configuration, packing format, and product status in the Microchip documentation. A package match alone is insufficient for firmware compatibility because bootloader behavior, peripheral configuration, and device identification can vary between ordering options.
Use the manufacturer's recommended programming and debug connections and preserve access to the reset and programming interface. For analog measurements and capacitive-touch channels, follow the documented acquisition sequence and source-impedance limits. Validate settling at the intended clock speed, compare measured noise against the required signal-to-noise ratio, and keep test points and debug clocks away from sensitive touch electrodes to avoid corrupting acquisition results.
合規資訊
The catalog identifies the ATSAML10E16A-AF as green, but no separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.