CD4024BMT - 7-Bit Ripple Counter | Texas Instruments
MPN: CD4024BMT ✓ সক্রিয়CD4024BMT সারাংশ
A binary counter is a sequential logic device that increments or decrements a binary value on each active clock transition. The CD4024 belongs to the CMOS logic family, where CMOS means complementary metal-oxide-semiconductor. Within the broader product hierarchy, it is a logic IC, then a counter and divider, and finally a digital semiconductor used to implement state, timing, and frequency functions in electronic systems.
The seven-stage architecture provides seven binary output stages, allowing division ratios from 2 through 128 when only the required output is used. Its negative-edge clock response means counting advances on the high-to-low transition of the clock signal. Separate parallel-load and master-reset inputs allow the counter to be initialized and controlled by external sequencing logic. The broad 3 V to 18 V supply range permits operation across common low-voltage and higher-voltage CMOS systems.
At a maximum clock frequency of 24 MHz, the CD4024BMT supports relatively fast counting compared with basic low-frequency timer-counter functions. The architecture is ripple-carry, so each internal stage advances after the preceding stage. This provides a simple implementation for modulo counters and frequency dividers, although accumulated propagation delay between stages must be considered in high-speed cascaded designs.
Typical uses include digital clock dividers, programmable timing generators, pulse and frequency counters, industrial sequence control, instrumentation, and embedded control systems. The 14-pin SOIC package supports conventional surface-mount assembly and fits PCB layouts designed around standard narrow-body integrated circuits.
Designers should account for ripple propagation delay when several counter stages influence timing-critical downstream logic. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be tied to a defined logic level. The negative-edge triggering behavior must also be reflected in the clock-driver and reset timing design.
This page combines the manufacturer's functional description, package and operating information, drop-in replacement assessment, side-by-side parameter comparison, and practical PCB guidance to support faster component selection and implementation planning.
এর জন্য ড্রপ-ইন বিকল্প CD4024BMT — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
CD4024BNSR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
CD4024BCM
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →HCF4024M013TR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
CD4024BMT সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Counter Type | 7-stage ripple-carry binary counter/divider |
| Number of Counter Elements | 1 element |
| Number of Binary Stages | 7 stages |
| Clock Edge | Negative edge |
| Logic Technology | CMOS |
| Supply Voltage Range | 3 V to 18 V |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 24 MHz |
| প্যাকেজ | 14-SOIC |
| পিন সংখ্যা | 14 pins |
| Package Width | 3.90 mm |
| অপারেটিং তাপমাত্রার পরিসর | -55 °C to 125 °C |
| মাউন্টিং টাইপ | Surface mount |
| Parallel Load Control | Yes |
| Master Reset Control | Yes |
CD4024BMT পিন কনফিগারেশন
| পিন 1 | CLK — Clock input; counting advances on the negative edge |
| পিন 2 | Q0 — Least-significant binary counter output |
| পিন 3 | Q1 — Binary counter output |
| পিন 4 | Q2 — Binary counter output |
| পিন 5 | Q3 — Binary counter output |
| পিন 6 | Q4 — Binary counter output |
| পিন 7 | Q5 — Binary counter output |
| পিন 8 | VSS — Ground reference |
| পিন 9 | MR — Master-reset input |
| পিন 10 | PE — Parallel-load enable input |
| পিন 11 | Q6 — Most-significant binary counter output |
| পিন 12 | VDD — Positive power supply |
| পিন 13 | NC — Not connected |
| পিন 14 | NC — Not connected |
সাধারণ ব্যবহার
CD4024BMT এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Binary Frequency Divider, Industrial Sequence Control, Digital Timing Generator, Pulse and Event Counter, Instrumentation and Measurement, Embedded Control State Machine.
Binary Frequency Divider
The CD4024BMT fits binary frequency-divider designs that need an integer division ratio between 2 and 128. Its seven counter outputs allow a clock to be divided by a power of two by selecting the appropriate Q output. The negative-edge clock response should be included in the timing diagram because each output changes after the corresponding ripple stage propagates. With a maximum clock frequency of 24 MHz, the device supports faster digital division than basic low-frequency timer-counter circuits, although PCB signal integrity and stage-delay accumulation must be checked at high input rates.
সুপারিশকৃত
Industrial Sequence Control
The CD4024BMT is suitable for sequencing control because its parallel-load input can initialize the counter and its master reset can return the count state to zero. These controls let external logic establish repeatable operating phases, while the seven Q outputs expose individual sequence steps. The 3 V to 18 V supply range accommodates many industrial control voltage levels, and the -55 °C to 125 °C operating range provides broad environmental capability. Designers should add reset synchronization and define all control levels during power-up to prevent unintended count states.
সুপারিশকৃত
Digital Timing Generator
A CD4024BMT can divide a periodic clock into slower timing intervals for pulse generation, elapsed-time measurement, and periodic system events. Seven available binary outputs provide related intervals at powers of two, making multiple timing taps available without adding another counter IC. The negative-edge trigger must be considered when the clock source is also used for another function. Because this is a ripple-carry implementation, downstream logic should not require all outputs to change simultaneously; use registered synchronization when coherent state transitions are necessary.
সুপারিশকৃত
Pulse and Event Counter
The CD4024BMT can count external events and divide a repetitive input clock for event-counting applications where a seven-bit count range is sufficient. Its single counter element and negative-edge input simplify control from a clean digital source, while parallel load and master reset support repeatable batch measurements. The 3 V to 18 V operating range permits integration across several standard CMOS supply levels. Keep event sources free of bounce, ringing, and level violations, and synchronize external asynchronous controls before they reach the counter inputs.
সুপারিশকৃত
Instrumentation and Measurement
The CD4024BMT is useful in instrumentation when a measured or reference signal must be converted into a binary count for subsequent display, processing, or control. Its seven Q outputs can represent a 0-to-127 sequence, providing a simple state interface to digital logic. The 24 MHz maximum clock frequency offers margin for dividing faster source signals before measurement. Signal conditioning remains essential: protect counter inputs from excessive voltage, ringing, and non-monotonic transitions, and route the clock to minimize coupling from switching nodes and output loads.
সুপারিশকৃত
Embedded Control State Machine
The CD4024BMT can implement a compact binary state progression within a larger embedded-control system. The counter advances on each falling clock edge, while parallel load and reset inputs allow the host controller to start, stop, or preset a sequence. Because the architecture is ripple-carry rather than synchronous, outputs change in a staged sequence; this can be advantageous for simple sequencing but may require output latching when downstream devices must observe a coherent state. Validate timing margins against the slowest system state transition and the required clock frequency.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা CD4024BMT — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | CD4024BNSR | CD4024BCM | HCF4024M013TR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi | STMicroelectronics |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Counter Stages | 7 stages | 7 stages | 7 bits | 7-stage binary counter |
মূল পার্থক্যসমূহ
- Maintains the established Texas Instruments CD4024B counter identity (বনামCD4024BCM)
- Provides seven binary stages for division ratios through 128 (বনামHCF4024M013TR)
- Uses the same 14-SOIC footprint as the documented cross-brand candidates (বনামCD4024BCM)
ডিজাইন নোট
The CD4024BMT counts on the negative clock edge, so the clock source must produce clean transitions with adequate rise and fall times. Route CLK away from Q outputs and other high-current switching nodes, use a compact ground-return path, and avoid stubs or test-point branches on the clock net. At high operating frequencies, probe the delivered clock at the device pin and compare it with the manufacturer timing requirements rather than relying only on the nominal 24 MHz maximum.
Place the supply-decoupling capacitor immediately between VDD and VSS, with its ground connection returned directly to the device ground plane. Keep the clock and control traces short, and place pull resistors where required for unused or high-impedance control inputs close to the associated pins. Because the counter uses ripple-carry stages, avoid feeding a Q output into a timing-critical path unless its transition delay has been included in the system timing budget.
Do not treat the seven Q outputs as changing simultaneously. A ripple counter advances its stages sequentially, so the interval between one output transition and the next can affect pulse width and setup time. Also define the state of the clock, master-reset, and parallel-load inputs during power-up and reset release. Unexpected transitions on the control inputs can initialize the count incorrectly or cause an unintended output sequence.
কমপ্লায়েন্স তথ্য
The device is a general-purpose CMOS logic IC rather than an automotive-qualified product, so AEC-Q100 is not applicable. Specific environmental-material declarations were not identified and remain unknown.