CD4024BMT - 7-Bit Ripple Counter | Texas Instruments
MPN: CD4024BMT ✓ 啟用中CD4024BMT 概覽
A binary counter is a sequential logic device that increments or decrements a binary value on each active clock transition. The CD4024 belongs to the CMOS logic family, where CMOS means complementary metal-oxide-semiconductor. Within the broader product hierarchy, it is a logic IC, then a counter and divider, and finally a digital semiconductor used to implement state, timing, and frequency functions in electronic systems.
The seven-stage architecture provides seven binary output stages, allowing division ratios from 2 through 128 when only the required output is used. Its negative-edge clock response means counting advances on the high-to-low transition of the clock signal. Separate parallel-load and master-reset inputs allow the counter to be initialized and controlled by external sequencing logic. The broad 3 V to 18 V supply range permits operation across common low-voltage and higher-voltage CMOS systems.
At a maximum clock frequency of 24 MHz, the CD4024BMT supports relatively fast counting compared with basic low-frequency timer-counter functions. The architecture is ripple-carry, so each internal stage advances after the preceding stage. This provides a simple implementation for modulo counters and frequency dividers, although accumulated propagation delay between stages must be considered in high-speed cascaded designs.
Typical uses include digital clock dividers, programmable timing generators, pulse and frequency counters, industrial sequence control, instrumentation, and embedded control systems. The 14-pin SOIC package supports conventional surface-mount assembly and fits PCB layouts designed around standard narrow-body integrated circuits.
Designers should account for ripple propagation delay when several counter stages influence timing-critical downstream logic. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be tied to a defined logic level. The negative-edge triggering behavior must also be reflected in the clock-driver and reset timing design.
This page combines the manufacturer's functional description, package and operating information, drop-in replacement assessment, side-by-side parameter comparison, and practical PCB guidance to support faster component selection and implementation planning.
直接替換替代品,適用於 CD4024BMT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
CD4024BNSR
✅ 直接替換📋 參考替代品(不在目錄中)
CD4024BCM
✅ 直接替換聯絡詢價
查看資料表 →HCF4024M013TR
✅ 直接替換📋 參考替代品(不在目錄中)
CD4024BMT 最大額定值與電氣特性
| Counter Type | 7-stage ripple-carry binary counter/divider |
| Number of Counter Elements | 1 element |
| Number of Binary Stages | 7 stages |
| Clock Edge | Negative edge |
| Logic Technology | CMOS |
| Supply Voltage Range | 3 V to 18 V |
| 最大時脈頻率 | 24 MHz |
| 封裝 | 14-SOIC |
| 腳位數 | 14 pins |
| Package Width | 3.90 mm |
| 工作溫度範圍 | -55 °C to 125 °C |
| 安裝類型 | Surface mount |
| Parallel Load Control | Yes |
| Master Reset Control | Yes |
CD4024BMT 腳位配置
| 腳位 1 | CLK — Clock input; counting advances on the negative edge |
| 腳位 2 | Q0 — Least-significant binary counter output |
| 腳位 3 | Q1 — Binary counter output |
| 腳位 4 | Q2 — Binary counter output |
| 腳位 5 | Q3 — Binary counter output |
| 腳位 6 | Q4 — Binary counter output |
| 腳位 7 | Q5 — Binary counter output |
| 腳位 8 | VSS — Ground reference |
| 腳位 9 | MR — Master-reset input |
| 腳位 10 | PE — Parallel-load enable input |
| 腳位 11 | Q6 — Most-significant binary counter output |
| 腳位 12 | VDD — Positive power supply |
| 腳位 13 | NC — Not connected |
| 腳位 14 | NC — Not connected |
典型應用
CD4024BMT 適用於 6 應用s: Binary Frequency Divider, Industrial Sequence Control, Digital Timing Generator, Pulse and Event Counter, Instrumentation and Measurement, Embedded Control State Machine.
Binary Frequency Divider
The CD4024BMT fits binary frequency-divider designs that need an integer division ratio between 2 and 128. Its seven counter outputs allow a clock to be divided by a power of two by selecting the appropriate Q output. The negative-edge clock response should be included in the timing diagram because each output changes after the corresponding ripple stage propagates. With a maximum clock frequency of 24 MHz, the device supports faster digital division than basic low-frequency timer-counter circuits, although PCB signal integrity and stage-delay accumulation must be checked at high input rates.
推薦
Industrial Sequence Control
The CD4024BMT is suitable for sequencing control because its parallel-load input can initialize the counter and its master reset can return the count state to zero. These controls let external logic establish repeatable operating phases, while the seven Q outputs expose individual sequence steps. The 3 V to 18 V supply range accommodates many industrial control voltage levels, and the -55 °C to 125 °C operating range provides broad environmental capability. Designers should add reset synchronization and define all control levels during power-up to prevent unintended count states.
推薦
Digital Timing Generator
A CD4024BMT can divide a periodic clock into slower timing intervals for pulse generation, elapsed-time measurement, and periodic system events. Seven available binary outputs provide related intervals at powers of two, making multiple timing taps available without adding another counter IC. The negative-edge trigger must be considered when the clock source is also used for another function. Because this is a ripple-carry implementation, downstream logic should not require all outputs to change simultaneously; use registered synchronization when coherent state transitions are necessary.
推薦
Pulse and Event Counter
The CD4024BMT can count external events and divide a repetitive input clock for event-counting applications where a seven-bit count range is sufficient. Its single counter element and negative-edge input simplify control from a clean digital source, while parallel load and master reset support repeatable batch measurements. The 3 V to 18 V operating range permits integration across several standard CMOS supply levels. Keep event sources free of bounce, ringing, and level violations, and synchronize external asynchronous controls before they reach the counter inputs.
推薦
Instrumentation and Measurement
The CD4024BMT is useful in instrumentation when a measured or reference signal must be converted into a binary count for subsequent display, processing, or control. Its seven Q outputs can represent a 0-to-127 sequence, providing a simple state interface to digital logic. The 24 MHz maximum clock frequency offers margin for dividing faster source signals before measurement. Signal conditioning remains essential: protect counter inputs from excessive voltage, ringing, and non-monotonic transitions, and route the clock to minimize coupling from switching nodes and output loads.
推薦
Embedded Control State Machine
The CD4024BMT can implement a compact binary state progression within a larger embedded-control system. The counter advances on each falling clock edge, while parallel load and reset inputs allow the host controller to start, stop, or preset a sequence. Because the architecture is ripple-carry rather than synchronous, outputs change in a staged sequence; this can be advantageous for simple sequencing but may require output latching when downstream devices must observe a coherent state. Validate timing margins against the slowest system state transition and the required clock frequency.
推薦
推薦產品摘要
工程參考資料,適用於 CD4024BMT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | CD4024BNSR | CD4024BCM | HCF4024M013TR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | onsemi | STMicroelectronics |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Counter Stages | 7 stages | 7 stages | 7 bits | 7-stage binary counter |
主要差異化特點
- Maintains the established Texas Instruments CD4024B counter identity (對比CD4024BCM)
- Provides seven binary stages for division ratios through 128 (對比HCF4024M013TR)
- Uses the same 14-SOIC footprint as the documented cross-brand candidates (對比CD4024BCM)
設計說明
The CD4024BMT counts on the negative clock edge, so the clock source must produce clean transitions with adequate rise and fall times. Route CLK away from Q outputs and other high-current switching nodes, use a compact ground-return path, and avoid stubs or test-point branches on the clock net. At high operating frequencies, probe the delivered clock at the device pin and compare it with the manufacturer timing requirements rather than relying only on the nominal 24 MHz maximum.
Place the supply-decoupling capacitor immediately between VDD and VSS, with its ground connection returned directly to the device ground plane. Keep the clock and control traces short, and place pull resistors where required for unused or high-impedance control inputs close to the associated pins. Because the counter uses ripple-carry stages, avoid feeding a Q output into a timing-critical path unless its transition delay has been included in the system timing budget.
Do not treat the seven Q outputs as changing simultaneously. A ripple counter advances its stages sequentially, so the interval between one output transition and the next can affect pulse width and setup time. Also define the state of the clock, master-reset, and parallel-load inputs during power-up and reset release. Unexpected transitions on the control inputs can initialize the count incorrectly or cause an unintended output sequence.
合規資訊
The device is a general-purpose CMOS logic IC rather than an automotive-qualified product, so AEC-Q100 is not applicable. Specific environmental-material declarations were not identified and remain unknown.