Texas Instruments

INA331IDGKR - 25 V/V Rail-to-Rail Instrumentation Amp | TI

MPN: INA331IDGKR ✓ সক্রিয়
±250 µV Vdss 1.00E-5 µA Id 8-pin VSSOP (DGK) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

INA331IDGKR সারাংশ

The Texas Instruments INA331IDGKR is a low-power, single-supply CMOS instrumentation amplifier with a closed-loop gain of 25 V/V, 2.0 MHz bandwidth, and 5 V/us slew rate, housed in an 8-pin VSSOP (DGK) package. It is designed for low-cost, high-gain accuracy with gain set by external resistors, 0.02% gain accuracy, and a 2 ppm/°C temperature coefficient. Additional headline specifications include ±250 µV offset voltage, 90 dB CMRR, and rail-to-rail operation.

An instrumentation amplifier is a differential-input analog signal-conditioning IC that amplifies the voltage difference between two sensors while rejecting common-mode interference. The INA331 belongs to the hierarchy of instrumentation amplifier, differential amplifier, analog amplifier, and amplifier IC. It is used where a small sensor differential must be measured accurately in the presence of larger common-mode voltages, particularly in battery-powered industrial, medical, and portable systems.

Key features include gain accuracy of 0.02% and a gain temperature coefficient of 2 ppm/°C for gains above 5 V/V. The device has an input offset voltage of ±250 µV, low input bias current, 90 dB CMRR, and a 2.0 MHz bandwidth. Its 5 V/us slew rate supports faster signal transitions, while single-supply and rail-to-rail operation simplify systems operating from a low-voltage source. The low-power design is suited to portable instrumentation and sensor interfaces.

The INA331 uses external gain-setting resistors, allowing the closed-loop gain to be adjusted for the required measurement range without changing the package. At the specified 25 V/V gain, the device combines useful bandwidth for low-frequency sensor measurements with common-mode rejection for noisy industrial environments. The input and output stages operate from a single supply, reducing the number of rails required in portable equipment.

Typical applications include low-side current sensing in battery systems, differential pressure and temperature measurement, biomedical instrumentation, portable sensor acquisition, industrial bridge excitation, and precision current measurement. The INA331 is especially appropriate when the sensor output is small, the required gain is above 5 V/V, and system power consumption must remain low.

When implementing the circuit, place the gain-setting resistors close to the gain inputs and keep the input differential loop area small to minimize noise pickup. Check the common-mode input range at the selected supply voltage and gain because the amplifier must remain within its valid operating region. Decoupling capacitors should be positioned close to the supply pins, with the layout verified against the manufacturer reference layout.

This page combines the exact orderable part information, package characteristics, gain and common-mode performance, application guidance, replacement analysis, and PCB considerations needed to evaluate INA331IDGKR before implementation.

এর জন্য ড্রপ-ইন বিকল্প INA331IDGKR — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

INA331AIDGKR

✅ ড্রপ-ইন
📦 VSSOP-8 (DGK)
Same INA331 family and DGK 8-pin footprint; the A suffix identifies a different orderable device or revision, with exact revision-specific limits requiring datasheet confirmation.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

INA331IDGKR সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Device Type Single-supply CMOS instrumentation amplifier
Number of Amplifiers 1 circuit
Closed-Loop Gain 25 V/V
Gain Accuracy 0.02%
Gain Temperature Coefficient 2 ppm/°C
Minimum External-Resistor Gain >5 V/V
Input Offset Voltage ±250 µV
CMRR 90 dB
CMRR at 45 kHz 94 dB
Bandwidth 2.0 MHz
Slew Rate 5 V/µs
Input Bias Current 1.00E-5 µA
সাপ্লাই ভোল্টেজ 5 V
অপারেটিং তাপমাত্রার পরিসর -55 °C to +125 °C
প্যাকেজ 8-pin VSSOP (DGK)
মাউন্টিং টাইপ Surface mount
আউটপুট টাইপ Rail-to-rail
Supply Type Single supply

INA331IDGKR 8-pin vssop (dgk) পিন কনফিগারেশন গাইড

INA331IDGKR (8-pin vssop (dgk) প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

INA331IDGKR-এর জন্য 8-pin vssop (dgk) প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি INA331IDGKR.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

INA331IDGKR এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Low-Side Current Sensing, Industrial Bridge-Sensor Interface, Portable Medical-Sensor Signal Conditioning, Portable Temperature and Pressure Sensing, Precision Current Monitoring, Low-Level Differential Voltage Acquisition.

⚡

Battery-Powered Low-Side Current Sensing

INA331IDGKR is appropriate for amplifying the small differential voltage produced by a low-side shunt while the power rail carries a much larger common-mode voltage. Its characterized 25 V/V closed-loop gain increases the shunt signal for an ADC, while 90 dB CMRR reduces errors caused by supply ripple and current-path variations. The 5 V/µs slew rate supports signals with moderate frequency content, and the 2.0 MHz bandwidth is appropriate for many power-control and battery-management channels. Keep the shunt and amplifier ground paths compact, verify the common-mode range at the selected gain, and place the supply bypass capacitor close to the device.

🏭

Industrial Bridge-Sensor Interface

INA331IDGKR can condition the small differential output of a resistive bridge sensor in an industrial measurement system. A 25 V/V gain accommodates millivolt-level bridge signals without requiring multiple amplifier stages, and the specified 0.02% gain accuracy supports repeatable conversion results. Its 90 dB CMRR helps preserve measurement integrity when the bridge shares ground paths with motors, relays, or switching converters. The single-supply, rail-to-rail architecture also suits compact sensor modules. Designers should use low-noise gain resistors, maintain a small differential input loop, and confirm that excitation and output levels remain within the datasheet limits.

💊

Portable Medical-Sensor Signal Conditioning

INA331IDGKR is suitable for low-level biomedical sensor conditioning when the selected gain, accuracy, and supply conditions satisfy the medical application's requirements. The 25 V/V gain can increase a weak differential sensor output before digitization, while ±250 µV offset and 0.02% gain accuracy support precision measurement. Low input bias current is valuable with high-impedance sensors, and the low-power single-supply design fits portable equipment. The -55 °C to +125 °C operating rating covers industrial temperature ranges, but it does not itself establish medical certification. Final designs must separately verify isolation, leakage current, electrode protection, noise performance, and applicable regulatory requirements.

🧩

Portable Temperature and Pressure Sensing

INA331IDGKR provides a compact analog front end for resistive temperature detectors, strain-based pressure sensors, and other differential transducers. Its 25 V/V gain reduces the dynamic range burden placed on the following ADC, while 90 dB CMRR improves rejection of common-mode noise found in longer cable runs. The 2.0 MHz bandwidth is more than adequate for many thermal and pressure measurements whose useful bandwidth is much lower. For portable systems, the single-supply architecture simplifies power management, and rail-to-rail output operation improves usable range. Place gain resistors close to the amplifier, protect inputs from ESD, and verify sensor excitation requirements and shutdown behavior during inactive periods.

🔧

Precision Current Monitoring

INA331IDGKR is well matched to precision current monitoring in power converters, battery packs, and portable test equipment. A shunt produces a differential voltage proportional to current, and the amplifier's 25 V/V gain raises that signal for measurement by an ADC or comparator. The 90 dB CMRR helps reject the fast common-mode transitions present in switching power paths, while 5 V/µs slew rate preserves response during current changes. The single-supply design is compatible with low-voltage systems. Use Kelvin routing where practical, keep the gain resistors close to the device, and verify both input and output headroom across the intended current range and supply tolerance.

📱

Low-Level Differential Voltage Acquisition

INA331IDGKR is useful when a system must measure a small differential voltage riding on a larger common-mode potential. Its characterized gain of 25 V/V, offset voltage of ±250 µV, and CMRR of 90 dB reduce the number of precision analog stages required. The 2.0 MHz bandwidth accommodates signal bandwidth beyond that of basic temperature sensors while avoiding unnecessary high-speed power requirements. The device can therefore serve in laboratory instrumentation, portable analyzers, and embedded sensor nodes. Confirm the valid common-mode range for the chosen gain and supply, review the resistor-based gain equation, and ensure the source impedance and input bias current meet the datasheet recommendations.

What is INA331IDGKR?
INA331IDGKR is a Texas Instruments single-supply CMOS instrumentation amplifier with a 25 V/V closed-loop gain, 2.0 MHz bandwidth, and 5 V/µs slew rate. According to the Texas Instruments INA331 datasheet, it uses external resistors to set gains above 5 V/V and is packaged in an 8-pin VSSOP. The part is intended for low-power sensor measurement, current sensing, and other applications requiring accurate differential amplification.
What are the key specifications of INA331IDGKR that engineers should know?
The principal INA331IDGKR specifications are 25 V/V closed-loop gain, 0.02% gain accuracy, ±250 µV input offset, 90 dB CMRR, 2.0 MHz bandwidth, and 5 V/µs slew rate. The Texas Instruments datasheet also specifies a 2 ppm/°C gain temperature coefficient for gains above 5 V/V and an operating range of -55 °C to +125 °C. The device operates from a single supply and provides rail-to-rail output operation.
Where can I download the INA331IDGKR datasheet PDF?
The official INA331IDGKR technical documentation is available through the Texas Instruments INA331 product page at https://www.ti.com/product/INA331. The orderable-part details identify INA331IDGKR as an 8-pin DGK VSSOP device rated from -55 °C to +125 °C. Use the datasheet linked from that page for pin descriptions, gain equations, electrical limits, typical performance curves, and recommended application layouts.
Where is the INA331IDGKR pinout?
The INA331IDGKR pinout is published in the pin-configuration section of the Texas Instruments INA331 datasheet. The exact orderable part uses an 8-pin VSSOP in the DGK package. Use the manufacturer pin-description table when assigning supply, ground, differential input, feedback, and gain-set functions, because the VSSOP-8 drawing is not represented by the package-diagram library available for this page.
How is the gain set on the INA331IDGKR?
The INA331IDGKR uses external gain-setting resistors, with gain established above 5 V/V. The Texas Instruments INA331 datasheet specifies 0.02% gain accuracy and a 2 ppm/°C gain temperature coefficient for this operating region. At the characterized 25 V/V configuration, the amplifier combines a 2.0 MHz bandwidth with 5 V/µs slew rate. Follow the datasheet gain equation and recommended resistor values when finalizing the circuit.
Can INA331IDGKR be used for low-side current sensing?
Yes, INA331IDGKR is suitable for low-side current sensing when the shunt differential voltage remains within the amplifier's valid input and output ranges. Its 25 V/V gain can increase the shunt signal before ADC conversion, while 90 dB CMRR helps reject common-mode voltage from the power path. The -55 °C to +125 °C rating and low-power single-supply architecture also suit industrial current-measurement channels.
What is the difference between INA331IDGKR and INA331AIDGKR?
INA331IDGKR and INA331AIDGKR are both Texas Instruments INA331-family devices in the DGK package, but the A designation identifies a different orderable device or product revision. The manufacturer cross-reference information associates INA331AIDGKR with INA331IDGKR and identifies both as low-power, single-supply CMOS instrumentation amplifiers. Confirm the exact ordering details, gain configuration, and temperature coverage against the manufacturer datasheet before substitution.
What is the best drop-in replacement for INA331IDGKR?
INA331AIDGKR is the closest documented drop-in candidate for INA331IDGKR because it belongs to the same INA331 family, uses the DGK package, and is associated with the target in manufacturer-oriented cross-reference information. The two orderable-device suffixes should still be checked for gain configuration and revision-specific operating limits. Use the Request a Quote form on this page to confirm current procurement status for the exact suffix.
Can INA331AIDGKR replace INA331IDGKR without PCB changes?
INA331AIDGKR can be treated as a drop-in candidate for INA331IDGKR because both are INA331-family DGK package devices and the cross-reference information identifies a direct relationship. Both use an 8-pin VSSOP format, eliminating a package-footprint change. Before release, compare the exact gain equation, input and output limits, supply range, and qualification requirements in the manufacturer documentation for both suffixes.
When should I choose INA331IDGKR over a general-purpose op amp?
Choose INA331IDGKR when the input is a small differential sensor signal that must be measured in the presence of a larger common-mode voltage. The integrated 25 V/V gain, 90 dB CMRR, ±250 µV offset, and single-supply operation simplify designs that would otherwise require several precision op-amp stages. A general-purpose op amp may offer more flexibility, but it requires additional gain-setting and common-mode rejection circuitry.
Is INA331IDGKR suitable for bridge-sensor and biomedical measurements?
INA331IDGKR is suitable for bridge-sensor and biomedical signal conditioning when the circuit's voltage, gain, noise, and accuracy requirements align with its specifications. The device provides 25 V/V gain, 0.02% gain accuracy, 90 dB CMRR, and low input bias current for weak differential sources. Biomedical designs must also independently verify patient-safety isolation, leakage, applicable qualification requirements, and system-level isolation.
How should INA331IDGKR be placed on a PCB for low noise?
Place the INA331IDGKR gain-setting resistors close to their associated pins and minimize the area of the differential input traces to reduce capacitive pickup. Connect the supply bypass capacitor directly to the supply and ground pins, and route return currents without sharing narrow paths with the sensor input. The Texas Instruments datasheet layout should be followed because PCB leakage and ground current can degrade the specified input offset and CMRR performance.
Where can I buy INA331IDGKR online?
Use the Request a Quote form on this page to request INA331IDGKR availability, current lead time, and a purchase quotation. The target is the Texas Instruments 8-pin DGK VSSOP orderable part, so quote the complete MPN INA331IDGKR to avoid receiving a different suffix or package. The form is the appropriate purchasing channel for exact-part sourcing and schedule confirmation.
What is the price of INA331IDGKR?
Current INA331IDGKR pricing is generated through the Request a Quote form on this page rather than displayed as a static value. Submit the complete MPN and required quantity, along with the desired delivery schedule, for a current quotation. This approach also allows the distributor channel to confirm whether the exact 8-pin DGK suffix is available for your production schedule.
What is the lead time and stock status for INA331IDGKR?
The current INA331IDGKR lead time and stock status should be confirmed through the Request a Quote form on this page. Request the exact complete MPN and include your target quantity, production date, and acceptable delivery window. For design planning, identify the part as the Texas Instruments INA331 in an 8-pin DGK VSSOP package rated for -55 °C to +125 °C operation.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা INA331IDGKR — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose INA331IDGKR for low-power, single-supply instrumentation designs that use external gain-setting resistors and need a compact 8-pin VSSOP implementation. Its characterized 25 V/V gain, 0.02% gain accuracy, ±250 µV offset, and 90 dB CMRR make it appropriate for low-side current sensing, bridge sensors, pressure sensing, and portable medical-signal conditioning. INA331AIDGKR is the closest documented drop-in candidate because it is associated with the same INA331 family and DGK package; confirm the exact suffix's electrical limits and revision details before substitution. A general-purpose op-amp design may be preferable when the gain must be selected independently, the signal bandwidth is much lower, or rail-to-rail input operation is required. No other cross-brand drop-in candidates were confirmed with both package and parametric compatibility, so they are not recommended for footprint reuse.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য INA331AIDGKR
Manufacturer Texas Instruments Texas Instruments
Package 8-pin VSSOP (DGK) 8-pin VSSOP (DGK)
Device Family INA331 INA331
Amplifier Type Single-supply CMOS instrumentation amplifier Single-supply CMOS instrumentation amplifier

মূল পার্থক্যসমূহ

  • Integrated precision gain for weak differential sensors (বনামINA331AIDGKR)
  • Common-mode rejection for noisy measurement paths (বনামINA331AIDGKR)
  • Low-power single-supply operation (বনামINA331AIDGKR)

ডিজাইন নোট

Place the external gain-setting resistors close to the INA331 gain-input pins and keep the differential input traces short and tightly coupled. High-impedance input nodes can pick up leakage and capacitive noise when routed near switching nodes. Connect the supply bypass capacitor directly between the supply and ground pins, and follow the manufacturer layout and grounding recommendations to preserve the specified offset and common-mode rejection behavior.

Before fixing the gain and supply voltage, verify the complete signal path against the input common-mode range, output swing, and gain-dependent limitations in the Texas Instruments INA331 datasheet. A low-side shunt measurement can have a large common-mode voltage even when its differential signal is small. The amplifier's single-supply architecture does not remove the need to check headroom at both input and output under worst-case load and supply conditions.

Do not substitute INA331AIDGKR solely because it uses the same DGK package. Although it is a documented same-family drop-in candidate, confirm the exact suffix's gain configuration, revision-specific electrical limits, temperature coverage, and ordering information in the manufacturer documentation. Also verify that the selected resistor values produce the intended gain and that the gain network's noise and temperature drift meet the measurement requirement.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The exact orderable-part information identifies INA331IDGKR as a Texas Instruments INA331 device in an 8-pin VSSOP (DGK) package. Specific environmental and material-compliance declarations were not stated in the orderable-part information and must be confirmed on the manufacturer product page before procurement.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

INA331IDGKR datasheet INA331IDGKR pinout INA331IDGKR datasheet pdf INA331IDGKR equivalent INA331IDGKR replacement INA331IDGKR vs INA331AIDGKR INA331IDGKR price INA331IDGKR stock INA331 VSSOP-8 pinout INA331 instrumentation amplifier application circuit Texas Instruments INA331IDGKR INA331 25 V/V instrumentation amplifier

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments INA331IDGKR INA331AIDGKR INA331 instrumentation amplifier differential amplifier analog amplifier amplifier IC CMOS single-supply operation rail-to-rail output closed-loop gain CMRR input offset voltage gain accuracy gain temperature coefficient bandwidth slew rate input bias current VSSOP-8 DGK package surface-mount package low-side current sensing bridge sensor sensor signal conditioning
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন