LM393BIDR - Dual Open-Collector Comparator | Texas Instruments
MPN: LM393BIDR ✓ সক্রিয়LM393BIDR সারাংশ
A comparator is an analog signal-conditioning IC that evaluates the voltage difference between its non-inverting and inverting inputs. When the non-inverting input rises above the inverting input, the associated output transistor turns off; when the relationship reverses, the output transistor turns on and pulls the output low. The LM393 family belongs to the comparator category within the broader analog IC and semiconductor hierarchies.
The B-version LM393 improves several parameters relative to the original LM393 family while remaining a drop-in replacement for LM293, LM393, and LM2903 A and V versions. Manufacturer product information lists a maximum input offset voltage of 2.5 mV, a response time of 1 µs, an input bias current of 3.5 nA, and supply current of 200 µA per comparator. The open-collector outputs are compatible with TTL, MOS, and CMOS logic.
Internally, the LM393 uses independent comparator channels referenced to a stable internal reference. Each output requires an external pull-up resistor because the open-drain transistor cannot actively drive a high state. The output sink current, low-level output voltage, and response performance are affected by the pull-up value, load capacitance, and the distance between the comparator and the receiving logic device.
Typical uses include DC overvoltage and undervoltage detection, zero-cross detection, battery monitoring, window comparators, and sensing switches for relays or MOSFETs. The wide differential input range also allows the device to compare signals that exceed the local supply voltage, provided the absolute maximum ratings and common-mode limits are respected.
When laying out a PCB, connect input traces away from switching nodes and route the pull-up resistor directly to the destination logic supply. Keep the input bias path short, decouple the supply pin close to the device, and verify the output pull-up voltage against the logic family being driven. Check the minimum operating supply and the absolute maximum supply rating separately because the input tolerance and supply rating are not interchangeable.
This page organizes pricing channels, drop-in alternatives, comparator pin assignments, and practical application guidance into a design-focused reference that helps engineers evaluate the LM393BIDR faster than a distributor parameter table alone.
এর জন্য ড্রপ-ইন বিকল্প LM393BIDR — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM393BIDR (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Operating Temperature Range, Comparator Type, Response Time, Output Type.
LM393DR
✅ ড্রপ-ইন✓ স্টকে আছে
$0.11 / ইউনিট
ডেটাশিট দেখুন →LM2903DR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM393AIDR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM2903AIDR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LMV393DR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM393BIDR সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Comparator Type | Dual differential general-purpose comparator |
| Number of Channels | 2 channels |
| আউটপুট টাইপ | Open-collector |
| Maximum Rated Supply Voltage | 38 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Common-Mode Input Range | Includes ground |
| Maximum Input Offset Voltage | 2.5 mV |
| Typical Low Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| সাপ্লাই কারেন্ট | 200 µA per comparator |
| Response Time | 1 µs |
| ESD Rating (HBM) | 2 kV |
| অপারেটিং তাপমাত্রার পরিসর | -40°C to +85°C |
| Output Compatibility | TTL, MOS, and CMOS |
| প্যাকেজ | 8-pin SOIC (D) |
| মাউন্টিং টাইপ | Surface mount |
LM393BIDR পিন কনফিগারেশন
| পিন 1 | OUT 1 — Open-collector output for comparator channel 1 |
| পিন 2 | IN 1- — Inverting input for comparator channel 1 |
| পিন 3 | IN 1+ — Non-inverting input for comparator channel 1 |
| পিন 4 | GND — Ground connection |
| পিন 5 | IN 2+ — Non-inverting input for comparator channel 2 |
| পিন 6 | IN 2- — Inverting input for comparator channel 2 |
| পিন 7 | OUT 2 — Open-collector output for comparator channel 2 |
| পিন 8 | VCC — Positive supply connection |
সাধারণ ব্যবহার
LM393BIDR এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: DC Overvoltage and Undervoltage Detection, Window Comparator for Limit Monitoring, Zero-Cross and AC Signal Detection, Motor and Relay Control Interface, Battery Pack Threshold Monitoring, Sensor Signal Conditioning and Limit Switching.
DC Overvoltage and Undervoltage Detection
The LM393BIDR fits battery and power-supply supervision because each channel compares a divided rail voltage with a reference and provides a pulled-up fault signal. A 38 V maximum rated supply and differential input range extending to -38 V and +38 V allow useful sensing ranges beyond the local supply, provided resistor dividers keep every pin within its rating. The 0.37 mV typical input offset voltage supports reasonably precise thresholds. One channel can monitor overvoltage and the other undervoltage, then drive a supervisor, relay, or system enable through the open-collector output.
সুপারিশকৃত
Window Comparator for Limit Monitoring
Two LM393BIDR channels can create an upper and lower voltage window around a precision reference. Divide the monitored signal into separate upper and lower threshold networks, connect each comparator to the appropriate reference polarity, and pull both open-collector outputs into a wired logic function. The 1 µs response time is useful for signals that require prompt state changes. The principal design concern is offset error around the thresholds, so use matched resistor networks and provide adequate supply bypassing to keep the reference node quiet.
সুপারিশকৃত
Zero-Cross and AC Signal Detection
The LM393BIDR can detect the point where an AC waveform crosses a reference level by comparing the signal with ground through one input and a bias node through the other. Its common-mode input range includes ground, making zero-volt sensing straightforward, while the wide differential input capability accommodates signals larger than the local logic supply. Because the output is open collector, a pull-up resistor can establish a clean logic-high pulse at the crossing. Keep the input network away from motor windings and use filtering if the detected edge must meet a specific timing requirement.
সুপারিশকৃত
Motor and Relay Control Interface
An LM393BIDR channel can turn a control-level request into a low-side switch drive for a relay, solenoid driver, or MOSFET gate stage. The open-collector output can sink the control current directly when the load is compatible, or it can drive an additional N-channel MOSFET when higher current is required. The 200 µA supply current per comparator is low enough for continuously powered control boards. Always include a flyback path for inductive loads and confirm that the output sink current and pull-up voltage remain within the device ratings.
সুপারিশকৃত
Battery Pack Threshold Monitoring
The LM393BIDR supports low-power battery monitoring by comparing a resistor-divided pack voltage against a precision reference on each channel. The comparator consumes 200 µA per channel according to manufacturer product information, making it practical for always-on protection circuits. Its differential input tolerance allows the sensing network to operate across several cell voltages without exposing the inputs to the full pack voltage. Add a temperature-stable reference, verify the divider tolerance, and choose resistor values that limit divider current to avoid dominating the comparator input current.
সুপারিশকৃত
Sensor Signal Conditioning and Limit Switching
The LM393BIDR can convert an analog sensor output into a hardware threshold event for thermistors, light sensors, pressure elements, or resistive dividers. Place the sensor network on one input and a reference on the other; the open-collector output then provides a pull-up-defined high level until the threshold is crossed. The dual-channel arrangement allows two limits or two independent sensor channels within one package. Minimize input trace length, keep high-impedance nodes away from switching nodes, and bypass the supply pin close to the package to avoid false threshold transitions.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM393BIDR — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM393DR | LM2903DR | LM393AIDR | LM2903AIDR | LMV393DR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Comparator Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-drain |
মূল পার্থক্যসমূহ
- Improved B-version offset performance in the standard SOIC-8 footprint (বনামLM393DR)
- Wide differential sensing capability for industrial threshold circuits (বনামLMV393DR)
- Direct family migration across LM393 and LM2903 base devices (বনামLM2903DR)
ডিজাইন নোট
Every open-collector output needs an external pull-up resistor. Calculate the worst-case pull-up current as (VLOGIC - VOLSAT) divided by the pull-up resistance, and confirm that this current remains below the comparator output sink-current rating. Place the resistor close to the receiving logic input or the comparator output so that a long trace does not add capacitance or pick up noise.
Keep the two differential input networks away from switching nodes, relay contacts, high-current return paths, and the pull-up resistor where possible. Connect the supply bypass capacitor close to pin 8 and ground pin 4. High-impedance input nodes should be surrounded by a grounded guard or keep-out area where practical, because capacitive coupling can cause false switching at the threshold.
Do not confuse the 38 V maximum rated supply with the permitted operating supply range. Likewise, the ability to accept differential inputs up to ±38 V does not make every input pin safe at ±38 V relative to ground. Verify each pin's absolute maximum voltage, common-mode limits, supply current, and output loading under worst-case temperature conditions before releasing the layout.
If a comparator drives a cable, relay, or long wiring harness, keep the sensitive input section compact and add protection close to the connector. The 2 kV HBM ESD rating describes device-level immunity, not unlimited connector protection. Use series resistors or clamping devices where the external harness can introduce transients, and ensure the ground reference at the comparator is not shared with high-current return paths.
কমপ্লায়েন্স তথ্য
The device is a commercial-grade dual comparator rated for -40°C to +85°C. Confirm current material and environmental compliance declarations for the exact ordering code with the manufacturer.