MC33172PG - Dual 44V Low-Power Op Amp | onsemi
MPN: MC33172PG ✓ সক্রিয়MC33172PG সারাংশ
An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences. The MC33172 belongs to the operational-amplifier hierarchy within analog signal-conditioning ICs. Its bipolar input stage uses conventional bipolar transistor technology rather than JFET devices, combining relatively low input-offset behavior with moderate bandwidth. The dual configuration permits two independent amplifier channels in one package, reducing board area when paired gain, filtering, or buffering functions are required.
The MC33172PG is particularly suited to single-supply systems because its 3.0 V minimum supply voltage allows operation from regulated 3.3 V or 5 V rails. Split supplies are also supported when the circuit requires a bipolar signal range around ground. The 44 V maximum supply voltage provides additional headroom for higher-voltage industrial interfaces, although input and output common-mode limits must still be respected. Both channels are intended for low-power operation at approximately 180 mA per amplifier.
With a gain-bandwidth product of 1.8 MHz and slew rate of 2.1 V/µs, the device is suitable for moderate-frequency precision rather than high-speed video or RF amplification. The 1.8 MHz gain-bandwidth product allows useful closed-loop bandwidth in lower-gain configurations, while the 2.1 V/µs slew rate limits large-signal response in wideband designs. These characteristics make signal rise times and stability more important than raw bandwidth in most applications.
Typical uses include industrial sensor conditioning, current-loop receivers, low-frequency active filters, audio preamplification, transducer interfaces, and general-purpose buffer stages. It is especially useful when two channels can share the same supply and ground arrangement. Because the package is an 8-pin PDIP, the device is also convenient for through-hole prototyping and repair assemblies where a surface-mount footprint would be inconvenient.
Design the input network, output loading, and supply decoupling around the ratings in the onsemi MC33172 datasheet. Place bypass capacitors close to the supply pins, observe the input common-mode range, and avoid driving capacitive loads unless stability compensation is provided. Confirm the exact pin assignments and operating limits against the manufacturer pin-description table before finalizing a PCB layout.
This product page combines the manufacturer specifications, commercial guidance, same-package replacement analysis, and application-oriented design considerations. It supports faster part selection while keeping the decisive checks—supply range, amplifier bandwidth, package, pin compatibility, and common-mode limits—visible at the design stage.
এর জন্য ড্রপ-ইন বিকল্প MC33172PG — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
MC33172P
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MC33172PG সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Count | 2 amplifiers |
| Product Type | Dual operational amplifier |
| Supply Voltage Range | 3.0 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz |
| Slew Rate | 2.1 V/µs |
| Operating Current per Amplifier | Approximately 180 mA |
| Input Transistor Technology | Bipolar |
| Supply Configuration | Single supply or split supply |
| প্যাকেজ | 8-pin PDIP |
| মাউন্টিং টাইপ | Through-hole |
| Temperature Grade | Industrial temperature range |
| Automotive Temperature Version | Available in the MC33171/72/74 series |
MC33172PG 8-pin pdip পিন কনফিগারেশন গাইড
MC33172PG (8-pin pdip প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MC33172PG.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MC33172PG এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filter, Current-Loop Receiver, Audio Preamplifier, Transducer Interface, Power Supply Feedback Buffer.
Industrial Sensor Signal Conditioning
The MC33172PG suits two-channel industrial sensor conditioning because it combines a 3.0 V minimum supply with approximately 180 mA operating current per amplifier. Place one channel around a sensor amplifier and use the second for filtering or an output buffer when the source impedance is high. The 1.8 MHz gain-bandwidth product supports moderate-gain stages, while the 2.1 V/µs slew rate handles sensor transients without operating as a high-speed amplifier. Protect inputs against excessive common-mode voltage and use local supply bypassing to prevent sensor excitation noise from coupling into the measurement chain.
সুপারিশকৃত
Low-Frequency Active Filter
The MC33172PG can implement dual-section low-frequency active filters using its two amplifier channels. The 1.8 MHz gain-bandwidth product is suitable for filters whose operating frequencies remain well below the closed-loop bandwidth limit, and the bipolar input stage supports general-purpose precision-oriented designs. Keep the feedback network values consistent with the selected topology and account for the amplifier's slew rate when processing large low-frequency signals. Decoupling capacitors should be placed near the supply pins, while sensitive filter nodes should remain away from high-current return paths.
সুপারিশকৃত
Current-Loop Receiver
The MC33172PG is appropriate for a 4-20 mA current-loop receiver when the application operates from a 5 V or higher supply and does not require modern micropower features. One channel can provide the main transimpedance or difference-amplifier function, while the other can add active filtering or a diagnostic buffer. Its 2.1 V/µs slew rate provides adequate response for many industrial process-control loops, but shunt-resistor values, common-mode limits, and input protection must be designed carefully. Verify loop bandwidth and transient behavior against the complete manufacturer electrical characteristics.
সুপারিশকৃত
Audio Preamplifier
The MC33172PG can serve as a dual-channel audio preamplifier in equipment that prioritizes simplicity and supply flexibility over low-noise performance. Its bipolar input stage, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate are suitable for low- and mid-frequency audio paths. Use one amplifier per channel to preserve channel symmetry, and configure input and feedback networks for the intended source impedance. Check the input noise, offset voltage, and output-swing requirements in the onsemi datasheet because a general-purpose operational amplifier may not match a dedicated audio amplifier.
সুপারিশকৃত
Transducer Interface
The MC33172PG is useful for bridge, resistive, or other transducer interfaces where two low-frequency amplifier stages are required. Its single-supply capability from 3.0 V simplifies systems that also use a 3.3 V embedded controller, and the second channel can provide excitation-buffer support, gain, or active filtering. The device's approximately 180 mA per-amplifier operating current must be included in the power budget. Input bias current, offset voltage, noise, and common-mode range are important when working with high-impedance sensors and should be checked against the final bridge impedance.
সুপারিশকৃত
Power Supply Feedback Buffer
The MC33172PG can buffer a remote or high-impedance feedback node in a linear power-supply control loop, with the second channel used for error amplification or signal conditioning. The 3.0 V to 44 V operating range permits use across multiple regulated-rail domains, while the 1.8 MHz gain-bandwidth product can support many compensation networks that operate at substantially lower crossover frequencies. Verify the input and output ranges at the exact rail voltages, maintain adequate phase margin, and avoid capacitive loading on the buffered feedback node unless stability has been evaluated.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC33172PG — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MC33172P |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | onsemi |
| Amplifier Configuration | Dual | Dual |
| Supply Voltage Range | 3.0 V to 44 V | 3.0 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz | 1.8 MHz |
| Slew Rate | 2.1 V/µs | 2.1 V/µs |
| Operating Current per Amplifier | Approximately 180 mA | Approximately 180 mA |
| Input Technology | Bipolar | Bipolar |
| Supply Modes | Single supply or split supply | Single supply or split supply |
| Special Ordering Detail | MC33172PG suffix | MC33172P ordering suffix; temperature and qualification details require comparison |
মূল পার্থক্যসমূহ
- Combines two channels with a broad supply range in one 8-pin PDIP package (বনামMC33172P)
- Moderate bandwidth and slew performance for low-power instrumentation (বনামMC33172P)
- Supports both 3.3 V and 5 V single-supply architectures (বনামMC33172P)
ডিজাইন নোট
Account for both channels when estimating the supply budget. Estimated: at a 5 V supply and approximately 180 mA per amplifier, the device can dissipate about 1.8 W with both outputs at their quiescent operating points. Actual dissipation changes with output voltage, load, and channel activity. Use the onsemi package dissipation and thermal information to determine whether the 8-pin PDIP requires a particular copper area or heat-spreading arrangement.
Route the two channels to minimize shared-impedance coupling between inputs, outputs, and ground returns. Place the supply bypass capacitor close to the positive and ground pins, and keep sensitive input traces away from power-supply switching nodes. In a dual-channel design, avoid routing one channel's output near the other channel's high-impedance input because parasitic coupling can create crosstalk or oscillation.
Do not treat the 3.0 V to 44 V supply rating as the usable input or output range. Common-mode voltage, output swing, and input-current limits are narrower and depend on the actual supply voltage. Confirm these boundaries in the manufacturer pin-description and electrical-characteristics tables. Also verify the complete MC33172 ordering suffix before substituting MC33172P, since temperature grade and qualification requirements may differ even though the package and principal family characteristics match.
কমপ্লায়েন্স তথ্য
The onsemi product-page material identifies industrial and automotive-temperature versions within the MC33171/72/74 family, but it does not state the MC33172PG suffix's individual RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.