MC33172PG - Dual 44V Low-Power Op Amp | onsemi
部品番号: MC33172PG ✓ 生産中MC33172PG 概要
An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences. The MC33172 belongs to the operational-amplifier hierarchy within analog signal-conditioning ICs. Its bipolar input stage uses conventional bipolar transistor technology rather than JFET devices, combining relatively low input-offset behavior with moderate bandwidth. The dual configuration permits two independent amplifier channels in one package, reducing board area when paired gain, filtering, or buffering functions are required.
The MC33172PG is particularly suited to single-supply systems because its 3.0 V minimum supply voltage allows operation from regulated 3.3 V or 5 V rails. Split supplies are also supported when the circuit requires a bipolar signal range around ground. The 44 V maximum supply voltage provides additional headroom for higher-voltage industrial interfaces, although input and output common-mode limits must still be respected. Both channels are intended for low-power operation at approximately 180 mA per amplifier.
With a gain-bandwidth product of 1.8 MHz and slew rate of 2.1 V/µs, the device is suitable for moderate-frequency precision rather than high-speed video or RF amplification. The 1.8 MHz gain-bandwidth product allows useful closed-loop bandwidth in lower-gain configurations, while the 2.1 V/µs slew rate limits large-signal response in wideband designs. These characteristics make signal rise times and stability more important than raw bandwidth in most applications.
Typical uses include industrial sensor conditioning, current-loop receivers, low-frequency active filters, audio preamplification, transducer interfaces, and general-purpose buffer stages. It is especially useful when two channels can share the same supply and ground arrangement. Because the package is an 8-pin PDIP, the device is also convenient for through-hole prototyping and repair assemblies where a surface-mount footprint would be inconvenient.
Design the input network, output loading, and supply decoupling around the ratings in the onsemi MC33172 datasheet. Place bypass capacitors close to the supply pins, observe the input common-mode range, and avoid driving capacitive loads unless stability compensation is provided. Confirm the exact pin assignments and operating limits against the manufacturer pin-description table before finalizing a PCB layout.
This product page combines the manufacturer specifications, commercial guidance, same-package replacement analysis, and application-oriented design considerations. It supports faster part selection while keeping the decisive checks—supply range, amplifier bandwidth, package, pin compatibility, and common-mode limits—visible at the design stage.
ドロップイン代替品: MC33172PG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
MC33172P
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MC33172PG 最大定格&電気的特性
| Amplifier Count | 2 amplifiers |
| Product Type | Dual operational amplifier |
| Supply Voltage Range | 3.0 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz |
| Slew Rate | 2.1 V/µs |
| Operating Current per Amplifier | Approximately 180 mA |
| Input Transistor Technology | Bipolar |
| Supply Configuration | Single supply or split supply |
| パッケージ | 8-pin PDIP |
| 実装タイプ | Through-hole |
| Temperature Grade | Industrial temperature range |
| Automotive Temperature Version | Available in the MC33171/72/74 series |
MC33172PG 8-pin pdip ピン配置ガイド
MC33172PG (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: MC33172PG.
詳細は データシート をご参照ください。
主な用途
MC33172PG の用途: 6 件s: Industrial Sensor Signal Conditioning, Low-Frequency Active Filter, Current-Loop Receiver, Audio Preamplifier, Transducer Interface, Power Supply Feedback Buffer.
Industrial Sensor Signal Conditioning
The MC33172PG suits two-channel industrial sensor conditioning because it combines a 3.0 V minimum supply with approximately 180 mA operating current per amplifier. Place one channel around a sensor amplifier and use the second for filtering or an output buffer when the source impedance is high. The 1.8 MHz gain-bandwidth product supports moderate-gain stages, while the 2.1 V/µs slew rate handles sensor transients without operating as a high-speed amplifier. Protect inputs against excessive common-mode voltage and use local supply bypassing to prevent sensor excitation noise from coupling into the measurement chain.
おすすめ
Low-Frequency Active Filter
The MC33172PG can implement dual-section low-frequency active filters using its two amplifier channels. The 1.8 MHz gain-bandwidth product is suitable for filters whose operating frequencies remain well below the closed-loop bandwidth limit, and the bipolar input stage supports general-purpose precision-oriented designs. Keep the feedback network values consistent with the selected topology and account for the amplifier's slew rate when processing large low-frequency signals. Decoupling capacitors should be placed near the supply pins, while sensitive filter nodes should remain away from high-current return paths.
おすすめ
Current-Loop Receiver
The MC33172PG is appropriate for a 4-20 mA current-loop receiver when the application operates from a 5 V or higher supply and does not require modern micropower features. One channel can provide the main transimpedance or difference-amplifier function, while the other can add active filtering or a diagnostic buffer. Its 2.1 V/µs slew rate provides adequate response for many industrial process-control loops, but shunt-resistor values, common-mode limits, and input protection must be designed carefully. Verify loop bandwidth and transient behavior against the complete manufacturer electrical characteristics.
おすすめ
Audio Preamplifier
The MC33172PG can serve as a dual-channel audio preamplifier in equipment that prioritizes simplicity and supply flexibility over low-noise performance. Its bipolar input stage, 1.8 MHz gain-bandwidth product, and 2.1 V/µs slew rate are suitable for low- and mid-frequency audio paths. Use one amplifier per channel to preserve channel symmetry, and configure input and feedback networks for the intended source impedance. Check the input noise, offset voltage, and output-swing requirements in the onsemi datasheet because a general-purpose operational amplifier may not match a dedicated audio amplifier.
おすすめ
Transducer Interface
The MC33172PG is useful for bridge, resistive, or other transducer interfaces where two low-frequency amplifier stages are required. Its single-supply capability from 3.0 V simplifies systems that also use a 3.3 V embedded controller, and the second channel can provide excitation-buffer support, gain, or active filtering. The device's approximately 180 mA per-amplifier operating current must be included in the power budget. Input bias current, offset voltage, noise, and common-mode range are important when working with high-impedance sensors and should be checked against the final bridge impedance.
おすすめ
Power Supply Feedback Buffer
The MC33172PG can buffer a remote or high-impedance feedback node in a linear power-supply control loop, with the second channel used for error amplification or signal conditioning. The 3.0 V to 44 V operating range permits use across multiple regulated-rail domains, while the 1.8 MHz gain-bandwidth product can support many compensation networks that operate at substantially lower crossover frequencies. Verify the input and output ranges at the exact rail voltages, maintain adequate phase margin, and avoid capacitive loading on the buffered feedback node unless stability has been evaluated.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC33172PG — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC33172P |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | onsemi |
| Amplifier Configuration | Dual | Dual |
| Supply Voltage Range | 3.0 V to 44 V | 3.0 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz | 1.8 MHz |
| Slew Rate | 2.1 V/µs | 2.1 V/µs |
| Operating Current per Amplifier | Approximately 180 mA | Approximately 180 mA |
| Input Technology | Bipolar | Bipolar |
| Supply Modes | Single supply or split supply | Single supply or split supply |
| Special Ordering Detail | MC33172PG suffix | MC33172P ordering suffix; temperature and qualification details require comparison |
主な差別化要因
- Combines two channels with a broad supply range in one 8-pin PDIP package (vs MC33172P)
- Moderate bandwidth and slew performance for low-power instrumentation (vs MC33172P)
- Supports both 3.3 V and 5 V single-supply architectures (vs MC33172P)
設計ノート
Account for both channels when estimating the supply budget. Estimated: at a 5 V supply and approximately 180 mA per amplifier, the device can dissipate about 1.8 W with both outputs at their quiescent operating points. Actual dissipation changes with output voltage, load, and channel activity. Use the onsemi package dissipation and thermal information to determine whether the 8-pin PDIP requires a particular copper area or heat-spreading arrangement.
Route the two channels to minimize shared-impedance coupling between inputs, outputs, and ground returns. Place the supply bypass capacitor close to the positive and ground pins, and keep sensitive input traces away from power-supply switching nodes. In a dual-channel design, avoid routing one channel's output near the other channel's high-impedance input because parasitic coupling can create crosstalk or oscillation.
Do not treat the 3.0 V to 44 V supply rating as the usable input or output range. Common-mode voltage, output swing, and input-current limits are narrower and depend on the actual supply voltage. Confirm these boundaries in the manufacturer pin-description and electrical-characteristics tables. Also verify the complete MC33172 ordering suffix before substituting MC33172P, since temperature grade and qualification requirements may differ even though the package and principal family characteristics match.
コンプライアンス情報
The onsemi product-page material identifies industrial and automotive-temperature versions within the MC33171/72/74 family, but it does not state the MC33172PG suffix's individual RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.