MCP6548-I/P - 1.6V Open-Drain CMOS Comparator | Microchip
MPN: MCP6548-I/P ✓ সক্রিয়MCP6548-I/P সারাংশ
A comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The MCP6548 belongs to the comparator hierarchy within analog and interface ICs, providing a simple alternative to discrete transistor or op-amp threshold circuits. Its open-drain output can be pulled upward to a suitable logic supply and can also be wired with other open-drain outputs to form wired-AND behavior.
The MCP6548-I/P operates from 1.6V to 5.5V, supports rail-to-rail inputs, and has a typical quiescent current of 600 nA, with a maximum of 1 microamp as stated on the Microchip product page. The output is capable of handling voltages up to 10V, allowing the open-drain output to interface with logic systems whose supply voltage exceeds the comparator's own operating range. The part is identified as a single-ended general-purpose comparator.
The comparator's CMOS architecture is appropriate for low-voltage embedded systems where supply current and signal headroom matter. Rail-to-rail input behavior allows the input signals to operate across the device supply range, while the open-drain output provides flexible voltage-level connection. Because the output is open drain, an external pull-up resistor is required when a high output state is needed. The pull-up voltage should be selected to remain compatible with the receiving logic and the comparator's output ratings.
Typical uses include battery-powered sensing, power-good and overvoltage detection, industrial threshold monitoring, digital control thresholds, sensor conditioning, and general-purpose analog-to-digital decision circuits. The low quiescent current is useful in portable equipment, while the 8-DIP package supports conventional through-hole assembly and prototyping.
For layout, place the pull-up resistor close to the open-drain output and keep comparator input traces short and away from switching nodes. Confirm input and output voltage limits, supply decoupling requirements, pull-up voltage, and temperature-range requirements against the manufacturer datasheet before production release. This page also organizes comparison information, practical application guidance, and design considerations around the MCP6548-I/P.
এর জন্য ড্রপ-ইন বিকল্প MCP6548-I/P — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
MCP6548-E/P
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MCP6548-I/P সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Comparator Type | Single, general-purpose comparator |
| Number of Elements | 1 |
| Supply Voltage Range | 1.6V to 5.5V |
| Input Common-Mode Range | Rail-to-rail |
| আউটপুট টাইপ | Open-drain CMOS, rail-to-rail, TTL-compatible |
| Quiescent Current, Typical | 600 nA |
| Quiescent Current, Maximum | 1 uA |
| Maximum Output Voltage | 10V |
| Input Configuration | Single-ended |
| প্যাকেজ | 8-DIP, 0.300 inch pitch, 7.62 mm |
| মাউন্টিং টাইপ | Through-hole |
| Output Pull-up Requirement | External pull-up resistor required |
| Logic Compatibility | TTL-compatible |
MCP6548-I/P 8-dip, 0.300 inch pitch, 7.62 mm পিন কনফিগারেশন গাইড
MCP6548-I/P (8-dip, 0.300 inch pitch, 7.62 mm প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MCP6548-I/P.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MCP6548-I/P এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Threshold Monitoring, Power-Good and Overvoltage Detection, Sensor Signal Detection, Industrial Digital Threshold Control, Digital Logic Interfacing, Portable and Embedded Equipment.
Battery-Powered Threshold Monitoring
The MCP6548-I/P is appropriate for monitoring a battery-derived or sensor-derived voltage against a reference in a compact, low-power system. Its 1.6V to 5.5V operating range supports common low-voltage rails, while the 600 nA typical quiescent current helps limit standby consumption. Place the device across the two comparison inputs and use the open-drain output to signal a threshold event. Because the output is open drain, the system requires an external pull-up to the logic rail. Check the input common-mode range, output timing, and pull-up current in the manufacturer datasheet before using the comparator as a battery protection decision element.
সুপারিশকৃত
Power-Good and Overvoltage Detection
The MCP6548-I/P can compare a divided power rail with a reference and produce an open-drain power-good or fault indication for a controller. Its rail-to-rail input behavior is useful when the monitored signal spans the operating supply range, and the output can be pulled up to the system logic voltage. In a multi-rail design, the comparator helps reduce the need for a dedicated supervisor when the required accuracy and timing are within its specified limits. Use resistor-divider values that keep the signal within the allowed input range and account for comparator offset when defining the switching threshold.
সুপারিশকৃত
Sensor Signal Detection
The MCP6548-I/P fits simple sensor thresholding, such as deciding when a temperature, light, or analog sensor output has crossed a set level. The single-ended comparator configuration converts a continuously varying analog condition into a logic-readable event without requiring a full amplifier chain. Rail-to-rail inputs help preserve usable signal range in low-voltage systems, while the open-drain output supports connection to MCU inputs or other open-drain logic. Keep the sensor reference or divider close to the comparator inputs to reduce noise pickup and select a pull-up resistor that satisfies the required rise time.
সুপারিশকৃত
Industrial Digital Threshold Control
The MCP6548-I/P can provide a local threshold decision in industrial control boards where a field sensor must be converted into a logic event. Its 1.6V to 5.5V supply range is compatible with embedded logic rails, and the open-drain output can be used to drive an alert, relay-control input, or digital isolation stage. For an industrial installation, select the ordering-code temperature grade that covers the expected ambient range and provide protection against transient inputs at the board interface. The comparator should sit behind appropriately scaled sensor inputs and surge-protection networks rather than directly handling unprotected field wiring.
সুপারিশকৃত
Digital Logic Interfacing
The MCP6548-I/P is useful when an analog condition must be converted to a digital signal for an MCU, programmable controller, or logic gate. Its TTL-compatible open-drain output supports standard digital interfacing, while the stated 10V output capability allows the pull-up rail to be selected for a compatible receiver. The output can be used to drive an enable, interrupt, or alarm input. Confirm the output current, propagation delay, and input thresholds in the manufacturer documentation, especially when the pull-up voltage is higher than the comparator's own supply.
সুপারিশকৃত
Portable and Embedded Equipment
The MCP6548-I/P is suitable for portable and embedded equipment where a compact comparator can perform a local decision without continuously powering a larger analog subsystem. The 600 nA typical quiescent current and 1 uA maximum specification are attractive for low-power designs, while the 8-DIP package supports through-hole prototypes and conventional assemblies. Keep the pull-up resistor value low enough for the required signal transition but high enough to remain within the output-current rating. Confirm the device's operating-temperature grade for the enclosure environment and account for leakage and pull-up current in the complete standby budget.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MCP6548-I/P — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MCP6548-E/P |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-DIP, 0.300 inch pitch, 7.62 mm | 8-DIP, 0.300 inch pitch, 7.62 mm |
| Comparator Elements | 1 | 1 |
| Ordering-Code Grade | I/P | E/P |
মূল পার্থক্যসমূহ
- Low-power single-comparator operation (বনামMCP6548-E/P)
- Wide low-voltage supply range (বনামMCP6548-E/P)
- Output voltage flexibility (বনামMCP6548-E/P)
ডিজাইন নোট
The MCP6548-I/P requires an external pull-up resistor for its open-drain output. Select the pull-up voltage for the receiving logic, then calculate the resistor using the required transition time and the load current. Keep the pull-up path short and verify that the output remains within the comparator's stated 10V capability. The comparator's 600 nA typical quiescent current should be added to the pull-up and external-circuit current when evaluating battery standby consumption.
Keep the two comparator inputs, especially the threshold or reference input, away from switching nodes and high-current return paths. Place the input resistors and any reference components close to the relevant pins, and route the pull-up resistor directly from the output to its intended logic supply. For a sensor input, use a physically quiet ground reference and maintain a short path from the sensor buffer or divider to the comparator.
Do not treat the open-drain output as a push-pull logic output: without a pull-up, the output has no actively driven high state. Also verify that the input voltages remain within the rail-to-rail operating range and that the selected ordering-code temperature grade covers the assembly's ambient temperature. Before production, check the manufacturer datasheet for input offset, propagation delay, output-current limits, and any power-up behavior requirements.
Use the lowest supply voltage that still provides the required comparator input range and output timing, while confirming that the pull-up rail is permitted for the open-drain output. The MCP6548-I/P can operate down to 1.6V, making it useful in low-voltage systems. If the comparator is powered separately from the logic receiver, sequence or isolate the rails so that the output is never exposed to an unsupported voltage during startup or shutdown.
কমপ্লায়েন্স তথ্য
Compliance status was not explicitly stated in the available product and distributor references. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Microchip before production release.