Microchip Technology

MCP6548-I/P - 1.6V Open-Drain CMOS Comparator | Microchip

N.º da peça: MCP6548-I/P ✓ Ativo
1.6V to 5.5V Vdss 600 nA Id 8-DIP, 0.300 inch pitch, 7.62 mm Package
MOQ: 1 |

MCP6548-I/P Visão geral

The Microchip Technology MCP6548-I/P is a single, general-purpose CMOS comparator with an open-drain output, operating from 1.6V to 5.5V. It is packaged in an 8-pin through-hole DIP and is designed for precision voltage comparison, threshold monitoring, signal detection, and interfacing between analog signals and digital logic. The device provides rail-to-rail input operation and TTL-compatible open-drain output behavior.

A comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The MCP6548 belongs to the comparator hierarchy within analog and interface ICs, providing a simple alternative to discrete transistor or op-amp threshold circuits. Its open-drain output can be pulled upward to a suitable logic supply and can also be wired with other open-drain outputs to form wired-AND behavior.

The MCP6548-I/P operates from 1.6V to 5.5V, supports rail-to-rail inputs, and has a typical quiescent current of 600 nA, with a maximum of 1 microamp as stated on the Microchip product page. The output is capable of handling voltages up to 10V, allowing the open-drain output to interface with logic systems whose supply voltage exceeds the comparator's own operating range. The part is identified as a single-ended general-purpose comparator.

The comparator's CMOS architecture is appropriate for low-voltage embedded systems where supply current and signal headroom matter. Rail-to-rail input behavior allows the input signals to operate across the device supply range, while the open-drain output provides flexible voltage-level connection. Because the output is open drain, an external pull-up resistor is required when a high output state is needed. The pull-up voltage should be selected to remain compatible with the receiving logic and the comparator's output ratings.

Typical uses include battery-powered sensing, power-good and overvoltage detection, industrial threshold monitoring, digital control thresholds, sensor conditioning, and general-purpose analog-to-digital decision circuits. The low quiescent current is useful in portable equipment, while the 8-DIP package supports conventional through-hole assembly and prototyping.

For layout, place the pull-up resistor close to the open-drain output and keep comparator input traces short and away from switching nodes. Confirm input and output voltage limits, supply decoupling requirements, pull-up voltage, and temperature-range requirements against the manufacturer datasheet before production release. This page also organizes comparison information, practical application guidance, and design considerations around the MCP6548-I/P.

Alternativas drop-in para MCP6548-I/P — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

MCP6548-E/P

✅ Drop-In
📦 8-DIP
Same MCP6548 family and 8-DIP package; E/P and I/P differ in temperature-grade designation, with no verified numeric electrical difference stated in the supplied references.

📋 Alternativa de referência (fora do catálogo)

MCP6548-I/P Classificações máximas e características elétricas

Comparator Type Single, general-purpose comparator
Number of Elements 1
Supply Voltage Range 1.6V to 5.5V
Input Common-Mode Range Rail-to-rail
Tipo de saída Open-drain CMOS, rail-to-rail, TTL-compatible
Quiescent Current, Typical 600 nA
Quiescent Current, Maximum 1 uA
Maximum Output Voltage 10V
Input Configuration Single-ended
Encapsulamento 8-DIP, 0.300 inch pitch, 7.62 mm
Tipo de montagem Through-hole
Output Pull-up Requirement External pull-up resistor required
Logic Compatibility TTL-compatible

Guia de Configuração de Pinos do MCP6548-I/P 8-dip, 0.300 inch pitch, 7.62 mm

Configuração de pinos para MCP6548-I/P (pacote 8-dip, 0.300 inch pitch, 7.62 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.

Diagrama de pinagem do pacote 8-dip, 0.300 inch pitch, 7.62 mm para MCP6548-I/P

Nenhum dado detalhado de pinagem disponível para MCP6548-I/P.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

MCP6548-I/P é adequado para 6 aplicaçãos: Battery-Powered Threshold Monitoring, Power-Good and Overvoltage Detection, Sensor Signal Detection, Industrial Digital Threshold Control, Digital Logic Interfacing, Portable and Embedded Equipment.

🔋

Battery-Powered Threshold Monitoring

The MCP6548-I/P is appropriate for monitoring a battery-derived or sensor-derived voltage against a reference in a compact, low-power system. Its 1.6V to 5.5V operating range supports common low-voltage rails, while the 600 nA typical quiescent current helps limit standby consumption. Place the device across the two comparison inputs and use the open-drain output to signal a threshold event. Because the output is open drain, the system requires an external pull-up to the logic rail. Check the input common-mode range, output timing, and pull-up current in the manufacturer datasheet before using the comparator as a battery protection decision element.

⚡

Power-Good and Overvoltage Detection

The MCP6548-I/P can compare a divided power rail with a reference and produce an open-drain power-good or fault indication for a controller. Its rail-to-rail input behavior is useful when the monitored signal spans the operating supply range, and the output can be pulled up to the system logic voltage. In a multi-rail design, the comparator helps reduce the need for a dedicated supervisor when the required accuracy and timing are within its specified limits. Use resistor-divider values that keep the signal within the allowed input range and account for comparator offset when defining the switching threshold.

🧩

Sensor Signal Detection

The MCP6548-I/P fits simple sensor thresholding, such as deciding when a temperature, light, or analog sensor output has crossed a set level. The single-ended comparator configuration converts a continuously varying analog condition into a logic-readable event without requiring a full amplifier chain. Rail-to-rail inputs help preserve usable signal range in low-voltage systems, while the open-drain output supports connection to MCU inputs or other open-drain logic. Keep the sensor reference or divider close to the comparator inputs to reduce noise pickup and select a pull-up resistor that satisfies the required rise time.

🏭

Industrial Digital Threshold Control

The MCP6548-I/P can provide a local threshold decision in industrial control boards where a field sensor must be converted into a logic event. Its 1.6V to 5.5V supply range is compatible with embedded logic rails, and the open-drain output can be used to drive an alert, relay-control input, or digital isolation stage. For an industrial installation, select the ordering-code temperature grade that covers the expected ambient range and provide protection against transient inputs at the board interface. The comparator should sit behind appropriately scaled sensor inputs and surge-protection networks rather than directly handling unprotected field wiring.

🖥️

Digital Logic Interfacing

The MCP6548-I/P is useful when an analog condition must be converted to a digital signal for an MCU, programmable controller, or logic gate. Its TTL-compatible open-drain output supports standard digital interfacing, while the stated 10V output capability allows the pull-up rail to be selected for a compatible receiver. The output can be used to drive an enable, interrupt, or alarm input. Confirm the output current, propagation delay, and input thresholds in the manufacturer documentation, especially when the pull-up voltage is higher than the comparator's own supply.

📱

Portable and Embedded Equipment

The MCP6548-I/P is suitable for portable and embedded equipment where a compact comparator can perform a local decision without continuously powering a larger analog subsystem. The 600 nA typical quiescent current and 1 uA maximum specification are attractive for low-power designs, while the 8-DIP package supports through-hole prototypes and conventional assemblies. Keep the pull-up resistor value low enough for the required signal transition but high enough to remain within the output-current rating. Confirm the device's operating-temperature grade for the enclosure environment and account for leakage and pull-up current in the complete standby budget.

Resumo dos produtos recomendados

MCP6548-E/P Same MCP6548 family comparator with a different ordering grade Usado em: Battery-Powered Threshold Monitoring, Power-Good and Overvoltage Detection, Sensor Signal Detection, Industrial Digital Threshold Control, Digital Logic Interfacing, Portable and Embedded Equipment
What is the operating voltage of MCP6548-I/P?
The MCP6548-I/P operates from 1.6V to 5.5V. According to the Microchip MCP6548 product page, this single comparator is designed for low-voltage CMOS systems and includes a typical quiescent current of 600 nA, with a maximum of 1 uA. The supply range makes it suitable for battery-powered and embedded applications, while the separately stated 10V output capability supports compatible open-drain interface designs.
What type of output does the MCP6548-I/P have?
The MCP6548-I/P has an open-drain CMOS output with rail-to-rail and TTL-compatible characteristics. The Microchip product page identifies the MCP6548 as an open-drain single comparator, and the distributor listing describes the I/P version as a CMOS, open-drain, rail-to-rail, TTL-compatible device. An external pull-up resistor is required to establish a high output level, and the pull-up voltage must match the receiving logic.
Is MCP6548-I/P a single or dual comparator?
The MCP6548-I/P is a single comparator with one comparator element. The DigiKey listing identifies it as a one-element, standard general-purpose comparator in an 8-PDIP package, while the Microchip family description identifies MCP6548 as a single-ended, open-drain device. The 8-pin package provides the comparator pins, power connections, and control functions described in the manufacturer documentation.
What is the quiescent current of MCP6548-I/P?
The MCP6548-I/P has a typical quiescent current of 600 nA and a maximum of 1 uA according to the Microchip product page. This low operating current supports portable and battery-powered equipment where comparator standby consumption affects the total system budget. The figure is measured for the comparator's specified operating conditions and should be checked against the datasheet before using it as a worst-case design limit.
Where can I find the MCP6548-I/P datasheet?
The official MCP6548 product information is available on the Microchip product page at https://www.microchip.com/en-us/product/MCP6548. The MCP6548-I/P is also indexed as an 8-PDIP open-drain comparator on distributor and datasheet-reference pages. Use the manufacturer documentation to confirm the complete pin assignment, electrical limits, recommended application circuit, and temperature and qualification details before finalizing a PCB or production BOM.
Where can I find the MCP6548-I/P pinout?
The MCP6548-I/P pinout is documented with the MCP6548 family information on the Microchip product page and in the corresponding manufacturer datasheet. The component uses an 8-pin DIP package with 0.300 inch pin spacing. Assign PCB connections from the datasheet pin-description table rather than relying on generic comparator diagrams, because enable, chip-select, and power-pin functions must match the specific ordering code.
Can MCP6548-I/P interface with TTL logic?
Yes. The MCP6548-I/P is identified as TTL-compatible and uses an open-drain output. Connect an external pull-up resistor to the logic supply used by the receiving circuit, then connect the open-drain output to the logic input. The output can also withstand a voltage up to 10V according to the Microchip product description, but the pull-up voltage, output current, and timing should remain within the limits defined in the datasheet.
What is the best drop-in replacement for MCP6548-I/P?
The MCP6548-E/P is the closest identified same-package option because it uses the same 8-PDIP form and belongs to the same MCP6548 family. Its temperature-grade designation differs from the I/P version, so it is not automatically interchangeable for every operating condition. The available cross-reference information does not establish five pin-compatible alternatives, and no alternative should be selected without checking the pin functions, electrical limits, and temperature requirements in the manufacturer datasheet.
What can replace MCP6548-I/P?
MCP6548-E/P is the identified family replacement candidate that preserves the 8-PDIP package and MCP6548 comparator function. The I/P and E/P ordering codes refer to different temperature grades, which can affect suitability across the full operating-temperature range. A true drop-in substitution must also preserve open-drain behavior, supply range, chip-select functionality, and electrical timing; no unqualified cross-brand replacement is confirmed by the available technical references.
MCP6548-I/P vs MCP6548-E/P - which is better for industrial use?
Choose between MCP6548-I/P and MCP6548-E/P by matching the required ambient-temperature range to the ordering-code grade. Both are identified as 8-PDIP MCP6548-family devices, so the mechanical package is suitable for the same through-hole footprint. The E/P designation identifies a different temperature grade, so the device with the grade covering the required industrial ambient range is preferable after checking the exact datasheet limits.
When should I choose MCP6548-I/P instead of MCP6548-E/P?
Choose MCP6548-I/P when its specified temperature grade covers the required ambient range and the design does not need the alternative grade. Choose MCP6548-E/P when its temperature grade is the correct fit for the installation environment. Both devices use the 8-DIP package and implement the same general-purpose open-drain comparator function, so the decision should be based on the ordering-code grade, operating-temperature requirement, and any additional procurement considerations.
Is MCP6548-I/P suitable for battery-powered monitoring?
The MCP6548-I/P is suitable for low-power monitoring because its operating supply range is 1.6V to 5.5V and its typical quiescent current is only 600 nA. It can compare a sensor or battery-derived signal against a reference and provide an open-drain logic indication. The external pull-up resistor and the surrounding sensor circuitry may dominate total standby current, so calculate the complete current path rather than relying on the comparator figure alone.
How do I use the MCP6548-I/P open-drain output?
Connect a pull-up resistor from the MCP6548-I/P output to the voltage required by the receiving logic. The output transistor pulls the node low when the comparator indicates its low state, while the resistor produces the high state when the transistor is off. If the output must remain valid when the comparator supply is disabled, include an appropriate pull-up arrangement and verify the system's power-sequencing requirements in the manufacturer documentation.
Where to buy MCP6548-I/P online?
Use the Request a Quote form on this page to request the current MCP6548-I/P quotation, availability, and lead time. The form keeps the request tied to the exact MPN and ordering code rather than a family-level listing. Distributor and comparison pages are indexed for this part, but current commercial terms can change and should be confirmed through the quote workflow for the exact MCP6548-I/P package and quantity.
What is the price of MCP6548-I/P?
The current MCP6548-I/P quotation is available through the Request a Quote form on this page. The available technical references identify the exact device and its distributor listings, but they do not provide a qualifying unit-quantity price table for this MPN. A quote for the exact ordering code is therefore the appropriate way to obtain current commercial terms, including stock, breaks, and lead time.
Is MCP6548-I/P in stock and what is its lead time?
Current MCP6548-I/P stock and lead time should be requested through the Request a Quote form on this page. The part is shown in distributor indexes and a listing snippet states that it ships today, but listing availability is not a guaranteed allocation for a specific order quantity. The quote response should confirm stock, scheduled delivery, and any manufacturer or distributor lead-time constraints for the exact 8-DIP ordering code.

Dados de referência de engenharia para MCP6548-I/P — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose MCP6548-I/P for a single, low-voltage threshold or power-monitoring function when the required temperature range matches the I/P ordering grade and the design benefits from open-drain logic interfacing. Its 1.6V to 5.5V supply range, 600 nA typical quiescent current, and 10V output capability make it suitable for portable and embedded systems. Choose MCP6548-E/P when that ordering grade covers the required ambient environment while retaining the same identified 8-DIP family package. Do not select a replacement solely from the comparator description: verify the pinout, chip-select behavior, input limits, offset, timing, and output current against the manufacturer datasheet. If an open-drain output is not required or the application needs a push-pull signal, a different comparator architecture may be more appropriate.

Comparação com alternativas

Parâmetro Este produto MCP6548-E/P
Brand Microchip Technology Microchip Technology
Package 8-DIP, 0.300 inch pitch, 7.62 mm 8-DIP, 0.300 inch pitch, 7.62 mm
Comparator Elements 1 1
Ordering-Code Grade I/P E/P

Principais diferenciais

  • Low-power single-comparator operation (vs MCP6548-E/P)
  • Wide low-voltage supply range (vs MCP6548-E/P)
  • Output voltage flexibility (vs MCP6548-E/P)

Notas de projeto

The MCP6548-I/P requires an external pull-up resistor for its open-drain output. Select the pull-up voltage for the receiving logic, then calculate the resistor using the required transition time and the load current. Keep the pull-up path short and verify that the output remains within the comparator's stated 10V capability. The comparator's 600 nA typical quiescent current should be added to the pull-up and external-circuit current when evaluating battery standby consumption.

Keep the two comparator inputs, especially the threshold or reference input, away from switching nodes and high-current return paths. Place the input resistors and any reference components close to the relevant pins, and route the pull-up resistor directly from the output to its intended logic supply. For a sensor input, use a physically quiet ground reference and maintain a short path from the sensor buffer or divider to the comparator.

Do not treat the open-drain output as a push-pull logic output: without a pull-up, the output has no actively driven high state. Also verify that the input voltages remain within the rail-to-rail operating range and that the selected ordering-code temperature grade covers the assembly's ambient temperature. Before production, check the manufacturer datasheet for input offset, propagation delay, output-current limits, and any power-up behavior requirements.

Use the lowest supply voltage that still provides the required comparator input range and output timing, while confirming that the pull-up rail is permitted for the open-drain output. The MCP6548-I/P can operate down to 1.6V, making it useful in low-voltage systems. If the comparator is powered separately from the logic receiver, sequence or isolate the rails so that the output is never exposed to an unsupported voltage during startup or shutdown.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

Compliance status was not explicitly stated in the available product and distributor references. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Microchip before production release.

Buscas relacionadas

MCP6548-I/P datasheet MCP6548-I/P pinout MCP6548-I/P datasheet pdf MCP6548-I/P 8-DIP MCP6548 open drain comparator MCP6548-I/P equivalent MCP6548-I/P replacement MCP6548-I/P vs MCP6548-E/P MCP6548-I/P price MCP6548-I/P stock Microchip MCP6548-I/P MCP6548-I/P application circuit MCP6548-I/P TTL output MCP6548-I/P 1.6V 5.5V

Componentes & termos relacionados

Microchip Technology MCP6548-I/P MCP6548 MCP6548-E/P Comparator Analog integrated circuit Interface IC Amplifier IC CMOS comparator Open-drain output Rail-to-rail input TTL-compatible logic 1.6V to 5.5V supply 600 nA quiescent current 10V output capability 8-DIP package Through-hole mounting 0.300 inch pin pitch Voltage threshold monitoring Power-good detection Sensor signal detection Digital logic interface Wired-AND interface Low-dropout power management hierarchy
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ