MCP6548-I/P - 1.6V Open-Drain CMOS Comparator | Microchip
MPN: MCP6548-I/P ✓ Hoạt độngMCP6548-I/P Tóm tắt
A comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The MCP6548 belongs to the comparator hierarchy within analog and interface ICs, providing a simple alternative to discrete transistor or op-amp threshold circuits. Its open-drain output can be pulled upward to a suitable logic supply and can also be wired with other open-drain outputs to form wired-AND behavior.
The MCP6548-I/P operates from 1.6V to 5.5V, supports rail-to-rail inputs, and has a typical quiescent current of 600 nA, with a maximum of 1 microamp as stated on the Microchip product page. The output is capable of handling voltages up to 10V, allowing the open-drain output to interface with logic systems whose supply voltage exceeds the comparator's own operating range. The part is identified as a single-ended general-purpose comparator.
The comparator's CMOS architecture is appropriate for low-voltage embedded systems where supply current and signal headroom matter. Rail-to-rail input behavior allows the input signals to operate across the device supply range, while the open-drain output provides flexible voltage-level connection. Because the output is open drain, an external pull-up resistor is required when a high output state is needed. The pull-up voltage should be selected to remain compatible with the receiving logic and the comparator's output ratings.
Typical uses include battery-powered sensing, power-good and overvoltage detection, industrial threshold monitoring, digital control thresholds, sensor conditioning, and general-purpose analog-to-digital decision circuits. The low quiescent current is useful in portable equipment, while the 8-DIP package supports conventional through-hole assembly and prototyping.
For layout, place the pull-up resistor close to the open-drain output and keep comparator input traces short and away from switching nodes. Confirm input and output voltage limits, supply decoupling requirements, pull-up voltage, and temperature-range requirements against the manufacturer datasheet before production release. This page also organizes comparison information, practical application guidance, and design considerations around the MCP6548-I/P.
Bộ thay thế dễ dàng lắp đặt cho MCP6548-I/P — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MCP6548-E/P
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCP6548-I/P Tỷ lệ tối đa & tính chất điện
| Comparator Type | Single, general-purpose comparator |
| Number of Elements | 1 |
| Supply Voltage Range | 1.6V to 5.5V |
| Input Common-Mode Range | Rail-to-rail |
| Kiểu đầu ra | Open-drain CMOS, rail-to-rail, TTL-compatible |
| Quiescent Current, Typical | 600 nA |
| Quiescent Current, Maximum | 1 uA |
| Maximum Output Voltage | 10V |
| Input Configuration | Single-ended |
| Hộp | 8-DIP, 0.300 inch pitch, 7.62 mm |
| Kiểu lắp đặt | Through-hole |
| Output Pull-up Requirement | External pull-up resistor required |
| Logic Compatibility | TTL-compatible |
Hướng dẫn cấu hình chân MCP6548-I/P 8-dip, 0.300 inch pitch, 7.62 mm
Cấu hình chân cho MCP6548-I/P (8-dip, 0.300 inch pitch, 7.62 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP6548-I/P.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP6548-I/P phù hợp cho 6 Áp dụngs: Battery-Powered Threshold Monitoring, Power-Good and Overvoltage Detection, Sensor Signal Detection, Industrial Digital Threshold Control, Digital Logic Interfacing, Portable and Embedded Equipment.
Battery-Powered Threshold Monitoring
The MCP6548-I/P is appropriate for monitoring a battery-derived or sensor-derived voltage against a reference in a compact, low-power system. Its 1.6V to 5.5V operating range supports common low-voltage rails, while the 600 nA typical quiescent current helps limit standby consumption. Place the device across the two comparison inputs and use the open-drain output to signal a threshold event. Because the output is open drain, the system requires an external pull-up to the logic rail. Check the input common-mode range, output timing, and pull-up current in the manufacturer datasheet before using the comparator as a battery protection decision element.
Được đề xuất
Power-Good and Overvoltage Detection
The MCP6548-I/P can compare a divided power rail with a reference and produce an open-drain power-good or fault indication for a controller. Its rail-to-rail input behavior is useful when the monitored signal spans the operating supply range, and the output can be pulled up to the system logic voltage. In a multi-rail design, the comparator helps reduce the need for a dedicated supervisor when the required accuracy and timing are within its specified limits. Use resistor-divider values that keep the signal within the allowed input range and account for comparator offset when defining the switching threshold.
Được đề xuất
Sensor Signal Detection
The MCP6548-I/P fits simple sensor thresholding, such as deciding when a temperature, light, or analog sensor output has crossed a set level. The single-ended comparator configuration converts a continuously varying analog condition into a logic-readable event without requiring a full amplifier chain. Rail-to-rail inputs help preserve usable signal range in low-voltage systems, while the open-drain output supports connection to MCU inputs or other open-drain logic. Keep the sensor reference or divider close to the comparator inputs to reduce noise pickup and select a pull-up resistor that satisfies the required rise time.
Được đề xuất
Industrial Digital Threshold Control
The MCP6548-I/P can provide a local threshold decision in industrial control boards where a field sensor must be converted into a logic event. Its 1.6V to 5.5V supply range is compatible with embedded logic rails, and the open-drain output can be used to drive an alert, relay-control input, or digital isolation stage. For an industrial installation, select the ordering-code temperature grade that covers the expected ambient range and provide protection against transient inputs at the board interface. The comparator should sit behind appropriately scaled sensor inputs and surge-protection networks rather than directly handling unprotected field wiring.
Được đề xuất
Digital Logic Interfacing
The MCP6548-I/P is useful when an analog condition must be converted to a digital signal for an MCU, programmable controller, or logic gate. Its TTL-compatible open-drain output supports standard digital interfacing, while the stated 10V output capability allows the pull-up rail to be selected for a compatible receiver. The output can be used to drive an enable, interrupt, or alarm input. Confirm the output current, propagation delay, and input thresholds in the manufacturer documentation, especially when the pull-up voltage is higher than the comparator's own supply.
Được đề xuất
Portable and Embedded Equipment
The MCP6548-I/P is suitable for portable and embedded equipment where a compact comparator can perform a local decision without continuously powering a larger analog subsystem. The 600 nA typical quiescent current and 1 uA maximum specification are attractive for low-power designs, while the 8-DIP package supports through-hole prototypes and conventional assemblies. Keep the pull-up resistor value low enough for the required signal transition but high enough to remain within the output-current rating. Confirm the device's operating-temperature grade for the enclosure environment and account for leakage and pull-up current in the complete standby budget.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP6548-I/P — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP6548-E/P |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-DIP, 0.300 inch pitch, 7.62 mm | 8-DIP, 0.300 inch pitch, 7.62 mm |
| Comparator Elements | 1 | 1 |
| Ordering-Code Grade | I/P | E/P |
Bảo phân biệt quan trọng
- Low-power single-comparator operation (vsMCP6548-E/P)
- Wide low-voltage supply range (vsMCP6548-E/P)
- Output voltage flexibility (vsMCP6548-E/P)
Ghi chú thiết kế
The MCP6548-I/P requires an external pull-up resistor for its open-drain output. Select the pull-up voltage for the receiving logic, then calculate the resistor using the required transition time and the load current. Keep the pull-up path short and verify that the output remains within the comparator's stated 10V capability. The comparator's 600 nA typical quiescent current should be added to the pull-up and external-circuit current when evaluating battery standby consumption.
Keep the two comparator inputs, especially the threshold or reference input, away from switching nodes and high-current return paths. Place the input resistors and any reference components close to the relevant pins, and route the pull-up resistor directly from the output to its intended logic supply. For a sensor input, use a physically quiet ground reference and maintain a short path from the sensor buffer or divider to the comparator.
Do not treat the open-drain output as a push-pull logic output: without a pull-up, the output has no actively driven high state. Also verify that the input voltages remain within the rail-to-rail operating range and that the selected ordering-code temperature grade covers the assembly's ambient temperature. Before production, check the manufacturer datasheet for input offset, propagation delay, output-current limits, and any power-up behavior requirements.
Use the lowest supply voltage that still provides the required comparator input range and output timing, while confirming that the pull-up rail is permitted for the open-drain output. The MCP6548-I/P can operate down to 1.6V, making it useful in low-voltage systems. If the comparator is powered separately from the logic receiver, sequence or isolate the rails so that the output is never exposed to an unsupported voltage during startup or shutdown.
Thông tin tuân thủ
Compliance status was not explicitly stated in the available product and distributor references. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Microchip before production release.