OPA187ID - 36V Zero-Drift Precision Op Amp | Texas Instruments
MPN: OPA187ID ✓ সক্রিয়OPA187ID সারাংশ
An operational amplifier is an analog building block that amplifies the voltage difference between its inverting and non-inverting inputs while providing high open-loop gain. The OPA187 belongs to the zero-drift precision operational-amplifier family, combining chopper-stabilized input-stage techniques with rail-to-rail output capability. This makes it suitable for instrumentation, sensor interfaces, current measurement, data acquisition, and test-equipment signal paths.
Key features include 10 µV typical input offset voltage, 0.001 µV/°C typical offset drift, rail-to-rail output operation, and a 36 V supply range. The device is also identified by Texas Instruments as MUX-friendly and low power. MUX-friendly operation is useful when a precision amplifier follows an analog multiplexer, where residual channel charge and switching transients can create input errors. Low power reduces system dissipation while retaining the low offset required by instrumentation applications.
The OPA187ID uses a CMOS precision architecture intended to minimize offset voltage and its temperature coefficient. Unlike a conventional bipolar precision amplifier whose offset behavior can change significantly over broad temperature ranges, the zero-drift architecture is intended to keep input-referred error nearly constant. Its rail-to-rail output allows useful output swing near the supply rails, although designers should consult the datasheet output-current and output-voltage limits before operating close to those boundaries.
Typical uses include precision sensor amplification, strain-gauge and bridge excitation measurement, low-current monitoring, industrial process-control signals, laboratory instrumentation, and high-resolution analog-to-digital converter input stages. In these applications, the 10 µV offset and 0.001 µV/°C drift help reduce stationary measurement error. The 36 V supply capability also permits operation from higher-voltage industrial rails when the signal and output-swing requirements remain within the device limits.
A critical design consideration is input-bias-current behavior at higher temperatures and the handling of source impedances. Follow the manufacturer datasheet when selecting input and output networks, bypassing supply pins, and defining the usable output range. The manufacturer also recommends limiting input current to 10 mA because excessive input current can forward-bias internal structures and cause input behavior to change.
This page combines manufacturer specifications, sourcing guidance, package information, application analysis, and verified drop-in comparison details to support faster component selection and PCB-level implementation decisions.
এর জন্য ড্রপ-ইন বিকল্প OPA187ID — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
OPA187IDR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
OPA187ID সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Single zero-drift precision operational amplifier |
| Number of Channels | 1 channel |
| Input Offset Voltage | 10 µV typical |
| Input Offset Voltage Drift | 0.001 µV/°C typical |
| Maximum Supply Voltage | 36 V |
| আউটপুট টাইপ | Rail-to-rail output |
| Technology | CMOS |
| Mux Friendly | Yes |
| অপারেটিং তাপমাত্রার পরিসর | -40 °C to +125 °C |
| প্যাকেজ | 8-pin SOIC (D) |
| মাউন্টিং টাইপ | Surface mount |
| Recommended Input Current Limit | 10 mA maximum |
OPA187ID পিন কনফিগারেশন
| পিন 1 | NC — No connect per the manufacturer pin description |
| পিন 2 | IN- — Inverting input |
| পিন 3 | IN+ — Non-inverting input |
| পিন 4 | V- — Negative supply connection |
| পিন 5 | NC — No connect per the manufacturer pin description |
| পিন 6 | OUT — Output |
| পিন 7 | V+ — Positive supply connection |
| পিন 8 | NC — No connect per the manufacturer pin description |
সাধারণ ব্যবহার
OPA187ID এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Strain-Gauge Bridge Amplification, Precision Current Measurement, Industrial Sensor Signal Conditioning, High-Resolution ADC Input Stage, Precision Instrumentation and Test Equipment, Low-Level Sensor Multiplexing.
Strain-Gauge Bridge Amplification
The OPA187ID is well suited to precision bridge measurement because its 10 µV typical input offset and 0.001 µV/°C typical drift limit input-referred error as temperature changes. It can serve as a difference amplifier or the precision input stage of an instrumentation amplifier for resistive bridges. The 36 V maximum supply voltage supports higher-voltage excitation or signal-chain requirements, while rail-to-rail output improves usable output range near the ADC input. Designers should confirm the amplifier's common-mode range, bias-current behavior, and output limits against the bridge excitation and full-scale sensor output.
সুপারিশকৃত
Precision Current Measurement
OPA187ID can amplify the small voltage produced by a shunt or current sensor where offset and thermal drift determine measurement accuracy. Its 10 µV typical input offset and 0.001 µV/°C typical drift are valuable when resolving microvolt-level signals, and the MUX-friendly characteristic supports designs that sample multiple current channels. The 8-pin SOIC package simplifies conventional analog routing, while the 36 V rating permits operation from an industrial supply. Verify input bias current and common-mode limits before choosing shunt resistance or sensor technology.
সুপারিশকৃত
Industrial Sensor Signal Conditioning
The OPA187ID fits low-level industrial sensor conditioning where long cable runs and temperature changes can create errors smaller than the signal itself. Its zero-drift architecture targets offset stability rather than simply minimizing broadband noise, making it appropriate for temperature, pressure, position, and resistance sensors. Rail-to-rail output provides useful headroom for driving an ADC, and the 36 V maximum supply supports higher-voltage industrial rails. Add input protection against surge and common-mode events rather than relying on amplifier inputs to absorb field-sourced energy.
সুপারিশকৃত
High-Resolution ADC Input Stage
OPA187ID can form the final voltage-gain stage before a high-resolution ADC when DC offset and drift would otherwise consume meaningful code space. Its 10 µV typical offset and 0.001 µV/°C typical drift are especially useful for slow, high-resolution measurements, while rail-to-rail output can increase the usable ADC input span. Place the amplifier close to the ADC when possible to reduce noise pickup, and confirm settling time and output-swing limits against the ADC sampling rate and acquisition window.
সুপারিশকৃত
Precision Instrumentation and Test Equipment
The OPA187ID is appropriate for laboratory and industrial instrumentation that must preserve small DC signals through amplification and measurement. Its zero-drift characteristics reduce calibration sensitivity to ambient temperature, while the MUX-friendly construction can simplify switched-input measurement systems. The 8-pin SOIC format is compatible with conventional instrument-board layouts, and the 36 V supply rating offers design flexibility. Engineers should evaluate noise density, settling behavior, input bias current, and overload behavior as part of the complete signal-chain budget.
সুপারিশকৃত
Low-Level Sensor Multiplexing
OPA187ID fits a multiplexed measurement front end because it is specifically identified as MUX-friendly and maintains very low offset drift. The amplifier can condition one selected sensor output at a time, helping preserve repeatability across channels. Rail-to-rail output leaves more of the available supply span for the selected signal, while the compact 8-pin SOIC package supports straightforward routing. The design must still account for mux charge injection, settling after channel selection, source impedance, and input bias current, particularly when the sensor has high impedance.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা OPA187ID — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | OPA187IDR |
|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) - same |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Type | Single zero-drift precision operational amplifier | Single zero-drift precision operational amplifier |
| Number of Channels | 1 channel | 1 channel |
| Input Offset Voltage | 10 µV typical | 10 µV typical |
| Offset Voltage Drift | 0.001 µV/°C typical | 0.001 µV/°C typical |
| Maximum Supply Voltage | 36 V | 36 V |
| Output Architecture | Rail-to-rail output | Rail-to-rail output |
| Multiplexer Compatibility | MUX-friendly | MUX-friendly |
| Technology | CMOS | CMOS |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C |
| Orderable Packaging Form | OPA187ID base ordering code | OPA187IDR tape-and-reel ordering code |
মূল পার্থক্যসমূহ
- Exceptionally low temperature-dependent offset drift (বনামOPA187IDR)
- Precision offset suitable for slow high-resolution signals (বনামOPA187IDR)
- Rail-to-rail operation with a 36 V maximum supply (বনামOPA187IDR)
- MUX-friendly precision architecture (বনামOPA187IDR)
ডিজাইন নোট
Keep the OPA187ID input current below the manufacturer's recommended 10 mA limit. Excessive input current can forward-bias internal structures, causing the input to source current and alter the apparent positive-supply behavior. Use series input resistance, source impedance, and appropriate clamping when the source can experience transients, floating conditions, or fault voltages. This limit is especially important when the amplifier follows protection networks whose leakage may rise at temperature.
Route the OPA187ID as a precision analog amplifier rather than as a general-purpose high-speed signal path. Keep the feedback network close to pins 2 and 6, provide a direct return from the ground connection to the analog ground reference, and place input and output paths away from switching nodes and high-current traces. Verify that the chosen SOIC layout has no exposed-pad requirement. The manufacturer pin diagram remains the controlling reference for every connection.
Account for amplifier offset, input bias current, mux charge injection, and settling after channel selection as separate error sources. A 10 µV offset specification alone does not establish total accuracy. For high-impedance sensors, calculate the bias-current-induced voltage error at the source impedance and confirm that the selected feedback resistors do not create unacceptable Johnson noise or introduce excessive parasitic capacitance. Bench-test mux transitions at the intended sampling rate.
The 36 V maximum supply rating is an absolute operating constraint, not a recommended operating point. Include transient margin for industrial supply variation and protection against ESD or wiring surges. Decouple the supply pins close to the device according to the manufacturer application guidance, and confirm the amplifier's common-mode and output ranges at the actual supply voltage. The 8-pin SOIC has no specified exposed thermal pad in the listed package configuration.
কমপ্লায়েন্স তথ্য
The manufacturer product page and ordering information identify the device as an 8-pin SOIC with an operating range of -40 °C to +125 °C. Separate environmental and material-compliance declarations were not present in the retrieved records, so these fields remain unknown.