PCA9539PWE4 - 16-Bit I2C I/O Expander | Texas Instruments
MPN: PCA9539PWE4 ✓ সক্রিয়PCA9539PWE4 সারাংশ
An I/O expander is a peripheral interface integrated circuit that connects digital input and output lines to a serial bus. Its functional hierarchy is I/O expander, bus interface controller, interface IC, and semiconductor. The PCA9539 family uses the I2C or SMBus protocol for register-based configuration and data transfer, making it suitable where adding a second parallel I/O port would otherwise require additional host pins or a separate controller.
The PCA9539PWE4 provides 16 individually configurable I/O lines, 400 kHz serial operation, interrupt output, hardware reset, and low-power behavior. Unlike the PCA9555, the PCA9539 removes the internal I/O pull-up resistors, reducing current consumption when outputs are held low. It also replaces the PCA9555 A2 address-control pin with RESET and uses a different device address range, so firmware and hardware address assignments must be reviewed carefully.
The 24-TSSOP package measures approximately 4.40 mm in body width and uses gull-wing leads. The device is offered in an industrial temperature grade. Its two supply pins support separate core and I/O voltage domains, allowing the interface to operate across systems with different logic levels when the voltage relationship remains within the device's operating requirements.
Typical uses include industrial controllers, programmable logic controllers, sensor and relay interfaces, keypad controllers, and embedded systems that need additional digital lines over a shared bus. The interrupt output allows the host to detect input changes without continuous register polling, helping reduce unnecessary serial activity. The RESET input provides a hardware mechanism for restoring the configurable registers to their default state.
PCB implementation should preserve the 24-TSSOP footprint, pin-1 orientation, bus pull-ups, supply decoupling, and accessible reset and interrupt routing. Because the I/O pins lack internal pull-ups, external resistors may be required for open-drain bus signals or inputs that must maintain a defined state. Check the manufacturer pin-description table before assigning tracks or external pull-up networks.
This product page combines the confirmed interface and package characteristics with practical implementation guidance, compatible-device comparisons, and design considerations for PCB layout, bus integrity, reset handling, and low-power I/O design.
এর জন্য ড্রপ-ইন বিকল্প PCA9539PWE4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible PCA9539PWE4 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.
TCA9539PWR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →PCA9539A
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
PCA9539PW,118
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
PCA9539APW,118
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
PCAL9539A
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
PCA9539PWE4 বিশেষণ
| Number of I/O Ports | 16 bits |
| ইন্টারফেস টাইপ | I2C and SMBus |
| Maximum Serial Clock Frequency | 400 kHz |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 0.4 MHz |
| Number of Supply Voltages | 2 |
| প্যাকেজ | 24-pin TSSOP |
| Package Body Width | 4.40 mm |
| Package Width | 0.173 inch |
| Terminal Count | 24 |
| Lead Form | Gull wing |
| মাউন্টিং স্টাইল | Surface mount |
| Temperature Grade | Industrial |
| Interrupt Output | Yes |
| Reset Function | Yes |
| Internal I/O Pull-Up Resistors | Not fitted |
PCA9539PWE4 0.173 inch পিন কনফিগারেশন গাইড
PCA9539PWE4 (0.173 inch প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PCA9539PWE4.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
PCA9539PWE4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Controller GPIO Expansion, PLC Digital Input and Output Module, Sensor and Relay Interface Board, Battery-Powered Sensor Node, Embedded Instrument Front Panel, General-Purpose Communication Interface.
Industrial Controller GPIO Expansion
The PCA9539PWE4 fits industrial controllers that need additional digital lines without consuming host-controller GPIO pins. A 16-bit I/O port can drive relay inputs, status LEDs, discrete enable signals, or digital sensors while the host communicates through the 2-wire I2C or SMBus interface at up to 400 kHz. The interrupt output allows the controller to react to input changes without continuously polling every port, reducing unnecessary processor activity. Because the PCA9539 has no internal I/O pull-ups, external resistors should be added wherever an input or open-drain interface requires one. Firmware should configure each port before use, verify the address assigned by A0 and A1, and preserve the separate core and I/O supply domains.
সুপারিশকৃত
PLC Digital Input and Output Module
PCA9539PWE4 is appropriate for programmable logic controller modules requiring a compact remote I/O bank. Sixteen configurable lines can represent digital inputs, outputs, or mixed functions, while the serial interface reduces the number of traces between the controller and field-I/O circuitry. The RESET input offers a defined hardware recovery path, and the interrupt output supports event-driven handling of changed inputs. In an industrial environment, external pull-ups and protection networks should be designed around the actual field signals. Confirm the I/O supply voltage against the logic requirements, isolate exposed connector circuits as required, and validate timing between the 400 kHz bus transaction and interrupt acknowledgement.
সুপারিশকৃত
Sensor and Relay Interface Board
The PCA9539PWE4 can concentrate digital sensor outputs and relay-control signals into one 24-TSSOP device. Input pins can monitor contact-closure or logic-level sensors, while output pins can control relay drivers or digital actuators, subject to the device's electrical limits. The interrupt line lets a host receive a prompt status change rather than polling all 16 lines continuously. Because the I/O ports do not contain internal pull-ups, use appropriate external resistors for open-collector sensors and control signals. Keep high-current or inductive loads away from the expander, place protection close to connector pins, and use a separate I/O supply when the field logic level differs from the host core voltage.
সুপারিশকৃত
Battery-Powered Sensor Node
PCA9539PWE4 supports compact, low-power sensor nodes because it provides 16 controllable lines from a serial bus and removes the PCA9555-family internal I/O pull-ups. The reduced standby current is especially useful when external pull-up networks would otherwise hold a line high continuously. A low-power host can use the interrupt output to wake from an idle state when an attached sensor changes state. Actual battery performance depends on external pull-up values, output duty cycle, bus activity, and the selected core and I/O supply voltages. In a wearable or portable design, minimize always-connected external pull-ups and disable unused port directions through the configuration registers.
সুপারিশকৃত
Embedded Instrument Front Panel
PCA9539PWE4 is useful in embedded instruments that need a bank of panel inputs and indicator outputs while preserving limited host-controller pins. Buttons, mode selectors, interlocks, and status LEDs can be connected through the 16-bit port, with the interrupt output notifying the host of user activity. The serial architecture also simplifies wiring compared with a direct parallel host port. Use the manufacturer pin table to preserve the interrupt and reset functions, and add external pull-ups where switches or open-drain signals require defined levels. For panel wiring exposed to electrostatic discharge or long cable runs, include suitable protection without loading the interrupt path.
সুপারিশকৃত
General-Purpose Communication Interface
PCA9539PWE4 can provide configurable parallel lines for communication adapters, programmable control panels, and general embedded interface boards. Its 400 kHz I2C/SMBus rate supports efficient register access while the 16-bit port handles discrete signals alongside a dedicated communication controller. The separate core and I/O supply pins support mixed voltage domains when the allowed operating relationship is satisfied. Interrupt-driven input handling improves responsiveness without a full polling loop, and RESET supports deterministic startup or fault recovery. Confirm the fixed address, address pins, bus pull-up arrangement, and power sequencing during schematic review so the host can reliably discover and initialize the peripheral.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PCA9539PWE4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TCA9539PWR | PCA9539A | PCA9539PW,118 | PCA9539APW,118 | PCAL9539A |
|---|---|---|---|---|---|---|
| Package | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP |
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| I/O Port Count | 16 bits | 16 bits | 16 bits | 16 bits | 16 bits | 16 bits |
| Serial Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Interrupt Output | Yes | Yes | Yes | Yes | Yes | Yes |
| Reset Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Special Features | Low-power design without internal I/O pull-ups | Configurable-register I/O expander | More fully featured pin-to-pin replacement | Base PCA9539 function in TSSOP-24 | PCA9539A family in TSSOP-24 | Agile I/O features |
মূল পার্থক্যসমূহ
- No internal I/O pull-up resistors (বনামPCA9555PW,112)
- Dedicated hardware reset and interrupt functions (বনামPCF8575PWR)
- Directly documented cross-brand replacement path (বনামPCA9539A)
- 400 kHz operation with 16 configurable lines (বনামTCA9539PWR)
ডিজাইন নোট
Route SDA and SCL as a compact, continuous bus with pull-up resistors placed near the master or the electrically appropriate end of the segment. Keep switching nodes, relay traces, and high-current return paths away from the bus to reduce injected noise. The 24-TSSOP footprint requires correct pin-1 orientation and gull-wing land patterns; review the manufacturer package drawing before finalizing the PCB footprint and solder mask.
Decouple the core and I/O supply pins separately and follow the manufacturer guidance for capacitor value and placement. Because PCA9539 I/O pins do not contain internal pull-ups, external pull-ups can create a continuous current path when an output is held low. Select resistor values from the logic voltage, leakage, transition speed, and maximum signal-loading requirements rather than copying a value without checking the actual interface.
Use the interrupt output as an edge-triggered event indication and service all pending port changes before returning to an idle state. Avoid treating the interrupt line as a level that can be ignored indefinitely. If several expanders share the bus, check address selection and confirm that each device has a unique address. Keep RESET deasserted during normal operation and define its startup state explicitly in the system power sequence.
Do not substitute PCA9555 without reviewing the address range, RESET/A2 arrangement, and missing internal I/O pull-ups. Configure unused pins as inputs or outputs according to the device's documented leakage behavior, and ensure external networks cannot back-power an unpowered I/O domain. Verify the exact register map after changing between PCA9539-family devices because similar descriptions do not guarantee identical software behavior.
কমপ্লায়েন্স তথ্য
The industrial temperature grade and component construction are documented, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. AEC-Q100 qualification is not applicable to the identified industrial-grade ordering code.