Texas Instruments

PCA9539PWE4 - 16-Bit I2C I/O Expander | Texas Instruments

N.º de pieza: PCA9539PWE4 ✓ Activo
2 Vdss 24-pin TSSOP Package 400 kHz Speed
MOQ: 1 |

PCA9539PWE4 Descripción general

Texas Instruments PCA9539PWE4 is a 16-bit I2C and SMBus low-power I/O expander operating up to 400 kHz, with interrupt and reset functions, housed in a 24-pin TSSOP package. The device expands a host controller's limited GPIO capability by providing 16 general-purpose input or output ports while retaining compact serial control over an I2C bus.

An I/O expander is a peripheral interface integrated circuit that connects digital input and output lines to a serial bus. Its functional hierarchy is I/O expander, bus interface controller, interface IC, and semiconductor. The PCA9539 family uses the I2C or SMBus protocol for register-based configuration and data transfer, making it suitable where adding a second parallel I/O port would otherwise require additional host pins or a separate controller.

The PCA9539PWE4 provides 16 individually configurable I/O lines, 400 kHz serial operation, interrupt output, hardware reset, and low-power behavior. Unlike the PCA9555, the PCA9539 removes the internal I/O pull-up resistors, reducing current consumption when outputs are held low. It also replaces the PCA9555 A2 address-control pin with RESET and uses a different device address range, so firmware and hardware address assignments must be reviewed carefully.

The 24-TSSOP package measures approximately 4.40 mm in body width and uses gull-wing leads. The device is offered in an industrial temperature grade. Its two supply pins support separate core and I/O voltage domains, allowing the interface to operate across systems with different logic levels when the voltage relationship remains within the device's operating requirements.

Typical uses include industrial controllers, programmable logic controllers, sensor and relay interfaces, keypad controllers, and embedded systems that need additional digital lines over a shared bus. The interrupt output allows the host to detect input changes without continuous register polling, helping reduce unnecessary serial activity. The RESET input provides a hardware mechanism for restoring the configurable registers to their default state.

PCB implementation should preserve the 24-TSSOP footprint, pin-1 orientation, bus pull-ups, supply decoupling, and accessible reset and interrupt routing. Because the I/O pins lack internal pull-ups, external resistors may be required for open-drain bus signals or inputs that must maintain a defined state. Check the manufacturer pin-description table before assigning tracks or external pull-up networks.

This product page combines the confirmed interface and package characteristics with practical implementation guidance, compatible-device comparisons, and design considerations for PCB layout, bus integrity, reset handling, and low-power I/O design.

Alternativas directas para PCA9539PWE4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con PCA9539PWE4 (mismo factor de forma y huella) — difiere en Package.

Texas Instruments
Package: 24-pin TSSOP (PW)
Comparar con PCA9539PWE4 →

TCA9539PWR

✅ Sustitución directa
Texas Instruments
📦 24-TSSOP
16-bit I2C and SMBus low-power I/O expander · 16 · 1.65 V to 5.5 V · 400 kHz · I2C and SMBus · 24-pin TSSOP (PW) · Surface mount · A0 and A1 hardware-selectable inputs

Consulte el precio

Ver hoja de datos →

PCA9539A

✅ Sustitución directa
📦 24-TSSOP
Explicitly documented as pin-to-pin replacement; additional device features and register behavior must be checked

📋 Alternativa de referencia (no en el catálogo)

PCA9539PW,118

✅ Sustitución directa
📦 24-TSSOP
Consistent terminals and package with compatible 16-bit I2C/SMBus operation; ordering code denotes bulk packaging

📋 Alternativa de referencia (no en el catálogo)

PCA9539APW,118

✅ Sustitución directa
📦 24-TSSOP
Pin-compatible PCA9539A family device in TSSOP-24; compare added features and register map against PCA9539

📋 Alternativa de referencia (no en el catálogo)

PCAL9539A

✅ Sustitución directa
📦 24-TSSOP
Same 24-TSSOP family and PCA9539-related pin-compatible platform; Agile I/O features differ from the base PCA9539

📋 Alternativa de referencia (no en el catálogo)

PCA9539PWE4 Especificaciones

Number of I/O Ports 16 bits
Tipo de interfaz I2C and SMBus
Maximum Serial Clock Frequency 400 kHz
Frecuencia de reloj máxima 0.4 MHz
Number of Supply Voltages 2
Encapsulado 24-pin TSSOP
Package Body Width 4.40 mm
Package Width 0.173 inch
Terminal Count 24
Lead Form Gull wing
Estilo de montaje Surface mount
Temperature Grade Industrial
Interrupt Output Yes
Reset Function Yes
Internal I/O Pull-Up Resistors Not fitted

Guía de configuración de pines de PCA9539PWE4 0.173 inch

Configuración de pines para PCA9539PWE4 (encapsulado 0.173 inch). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 0.173 inch para PCA9539PWE4

No hay datos detallados de patillaje disponibles para PCA9539PWE4.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

PCA9539PWE4 es adecuado para 6 aplicacións: Industrial Controller GPIO Expansion, PLC Digital Input and Output Module, Sensor and Relay Interface Board, Battery-Powered Sensor Node, Embedded Instrument Front Panel, General-Purpose Communication Interface.

🏭

Industrial Controller GPIO Expansion

The PCA9539PWE4 fits industrial controllers that need additional digital lines without consuming host-controller GPIO pins. A 16-bit I/O port can drive relay inputs, status LEDs, discrete enable signals, or digital sensors while the host communicates through the 2-wire I2C or SMBus interface at up to 400 kHz. The interrupt output allows the controller to react to input changes without continuously polling every port, reducing unnecessary processor activity. Because the PCA9539 has no internal I/O pull-ups, external resistors should be added wherever an input or open-drain interface requires one. Firmware should configure each port before use, verify the address assigned by A0 and A1, and preserve the separate core and I/O supply domains.

🏭

PLC Digital Input and Output Module

PCA9539PWE4 is appropriate for programmable logic controller modules requiring a compact remote I/O bank. Sixteen configurable lines can represent digital inputs, outputs, or mixed functions, while the serial interface reduces the number of traces between the controller and field-I/O circuitry. The RESET input offers a defined hardware recovery path, and the interrupt output supports event-driven handling of changed inputs. In an industrial environment, external pull-ups and protection networks should be designed around the actual field signals. Confirm the I/O supply voltage against the logic requirements, isolate exposed connector circuits as required, and validate timing between the 400 kHz bus transaction and interrupt acknowledgement.

🧩

Sensor and Relay Interface Board

The PCA9539PWE4 can concentrate digital sensor outputs and relay-control signals into one 24-TSSOP device. Input pins can monitor contact-closure or logic-level sensors, while output pins can control relay drivers or digital actuators, subject to the device's electrical limits. The interrupt line lets a host receive a prompt status change rather than polling all 16 lines continuously. Because the I/O ports do not contain internal pull-ups, use appropriate external resistors for open-collector sensors and control signals. Keep high-current or inductive loads away from the expander, place protection close to connector pins, and use a separate I/O supply when the field logic level differs from the host core voltage.

📱

Battery-Powered Sensor Node

PCA9539PWE4 supports compact, low-power sensor nodes because it provides 16 controllable lines from a serial bus and removes the PCA9555-family internal I/O pull-ups. The reduced standby current is especially useful when external pull-up networks would otherwise hold a line high continuously. A low-power host can use the interrupt output to wake from an idle state when an attached sensor changes state. Actual battery performance depends on external pull-up values, output duty cycle, bus activity, and the selected core and I/O supply voltages. In a wearable or portable design, minimize always-connected external pull-ups and disable unused port directions through the configuration registers.

🔧

Embedded Instrument Front Panel

PCA9539PWE4 is useful in embedded instruments that need a bank of panel inputs and indicator outputs while preserving limited host-controller pins. Buttons, mode selectors, interlocks, and status LEDs can be connected through the 16-bit port, with the interrupt output notifying the host of user activity. The serial architecture also simplifies wiring compared with a direct parallel host port. Use the manufacturer pin table to preserve the interrupt and reset functions, and add external pull-ups where switches or open-drain signals require defined levels. For panel wiring exposed to electrostatic discharge or long cable runs, include suitable protection without loading the interrupt path.

🌐

General-Purpose Communication Interface

PCA9539PWE4 can provide configurable parallel lines for communication adapters, programmable control panels, and general embedded interface boards. Its 400 kHz I2C/SMBus rate supports efficient register access while the 16-bit port handles discrete signals alongside a dedicated communication controller. The separate core and I/O supply pins support mixed voltage domains when the allowed operating relationship is satisfied. Interrupt-driven input handling improves responsiveness without a full polling loop, and RESET supports deterministic startup or fault recovery. Confirm the fixed address, address pins, bus pull-up arrangement, and power sequencing during schematic review so the host can reliably discover and initialize the peripheral.

What are the key specifications of PCA9539PWE4 that engineers should know?
The PCA9539PWE4 is a 16-bit I2C and SMBus I/O expander with a maximum clock frequency of 400 kHz in a 24-pin TSSOP package. It provides interrupt and reset functions, operates as a low-power peripheral, and uses two supply-voltage domains. According to the Texas Instruments product page, the PCA9539 has no internal I/O pull-up resistors, which reduces current consumption when outputs are held low.
What is the PCA9539PWE4 used for?
The PCA9539PWE4 adds 16 configurable digital I/O lines to a host controller through an I2C or SMBus interface. It is useful in embedded products, industrial controllers, sensor interfaces, relay-control boards, and programmable logic systems where the host lacks enough GPIO pins. Each port can be configured through registers for input or output operation, while the interrupt output can signal input-state changes.
Where can I download the PCA9539PWE4 datasheet PDF?
The official PCA9539 documentation is available through the Texas Instruments product page at https://www.ti.com/product/PCA9539. From that page, open the datasheet link for the complete pin descriptions, register map, electrical characteristics, and application information. The product page also distinguishes PCA9539 from PCA9555 by documenting the removal of internal I/O pull-ups, the RESET function, and the changed address range.
Where is the PCA9539PWE4 pinout?
The PCA9539PWE4 pinout is published in the Texas Instruments PCA9539 datasheet under the pin configuration and pin-description tables. The device uses a 24-pin TSSOP package with gull-wing leads and counter-clockwise numbering as viewed from the top. Use the manufacturer table to assign the 16 I/O pins, VDD, VDDIO, GND, address pins, RESET, and interrupt signal without relying on assumptions based on another 24-pin interface IC.
Is PCA9539PWE4 pin-compatible with PCA9539A?
Yes, the NXP PCA9539A is identified as a pin-to-pin replacement for the PCA9539 and other industry-standard devices. Its additional functional capabilities should still be reviewed in its own datasheet, including register behavior and electrical characteristics. Before substitution, confirm the package, supply-voltage limits, address selection, reset implementation, and interrupt polarity in the target system.
What is the difference between PCA9539 and PCA9555?
The PCA9539 is functionally similar to the PCA9555 but removes the internal I/O pull-up resistors, which reduces power consumption when I/O lines are held low. The PCA9539 also replaces the PCA9555 A2 pin with RESET and implements a different address range. According to the Texas Instruments product page, those differences require firmware and board-level review, even though both devices serve as 16-bit remote I/O expanders.
When should I choose PCA9539PWE4 over TCA9539PWR?
Choose PCA9539PWE4 when its 16-bit I2C/SMBus configuration, interrupt output, reset behavior, and 400 kHz operating limit match the design requirements. Choose TCA9539PWR when its independently documented register map or device-specific characteristics provide a functional advantage. Both are presented in the same TSSOP-24 package family, but firmware must use the register definition matching the selected device rather than assuming every register is identical.
PCA9539PWE4 vs TCA9539PWR - which is better for an industrial controller?
PCA9539PWE4 is the better-supported choice when the board has already been designed around the PCA9539 register map or when the Texas Instruments device is the specified source. TCA9539PWR may be preferable when its documented electrical and register characteristics better match a new design. Both use a 24-pin TSSOP package, so the mechanical fit is compatible, but interrupt polarity, reset behavior, address options, and register access must be checked.
What is the best drop-in replacement for PCA9539PWE4?
The PCA9539A is the clearest documented drop-in replacement because NXP identifies it as pin-to-pin compatible with the PCA9539. The NXP PCA9539PW,118 is another documented package-and-terminal-compatible option for the 24-pin TSSOP implementation. A PCB substitution should still confirm supply levels, reset behavior, interrupt polarity, pull-up requirements, and the exact register map before production release.
Can TCA9539PWR replace PCA9539PWE4 without changing the PCB?
TCA9539PWR uses the same 24-pin TSSOP package and is identified as a 16-bit remote I2C/SMBus low-power I/O expander with interrupt, reset, and configurable registers. A hardware replacement is plausible when pin functions and electrical limits match the target design. Treat it as a qualified drop-in only after checking the TCA9539PWR pin table, reset polarity, I2C address range, and register compatibility.
How do I calculate the I2C bus address for PCA9539PWE4?
The PCA9539PWE4 I2C address is selected through its hardware address inputs and differs from the PCA9555 address range. The manufacturer datasheet provides the complete address table and device-identification sequence. Firmware should use the table for the actual A0 and A1 connections, then include the read or write bit when constructing transactions; changing an address pin without updating firmware can leave the device unreachable.
Does PCA9539PWE4 need external I/O pull-up resistors?
The PCA9539 does not include internal pull-up resistors on its I/O pins. External pull-ups may therefore be needed on open-drain signals or inputs that otherwise lack a defined high level. The I2C bus itself normally requires suitable pull-up resistors, and the exact resistance should be selected from the bus capacitance, logic voltage, rise-time requirement, and the current allowed by every connected peripheral.
Where can I buy PCA9539PWE4 and check current availability?
Use the Request a Quote form on this page to request PCA9539PWE4 availability, current lead time, and order details. The form is the appropriate commercial channel for this listing, and no static price should be assumed because market and production conditions can change. Provide the required quantity, target package suffix, and any date-sensitive delivery requirement in the request.
What is the lead time for PCA9539PWE4?
The current lead time for PCA9539PWE4 should be requested through the Request a Quote form on this page rather than inferred from an older catalog listing. Include your required quantity, approved source status, and production schedule when requesting confirmation. Packaging and order quantity can affect practical lead time, so request a commitment for the exact ordering configuration.
Is PCA9539PWE4 suitable for low-power battery-powered equipment?
PCA9539PWE4 can suit battery-powered equipment because the PCA9539 is designed for low current consumption and its I/O pins do not include the internal pull-up resistors found on the PCA9555. The system-level result still depends on how long the I/O lines are held in each state and whether external pull-ups create a continuous current path. Measure the assembled standby current at the application level before finalizing the power budget.

Datos de referencia de ingeniería para PCA9539PWE4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose PCA9539PWE4 when an existing design needs a 16-bit, 400 kHz I2C/SMBus I/O expander with interrupt and reset functions in 24-TSSOP. Its lack of internal I/O pull-ups is advantageous for low-power designs, provided the board supplies any required external resistors. Select PCA9539A or PCA9539APW,118 for a documented second-source path, after checking the revised register behavior and device-specific features. PCA9539PW,118 offers another TSSOP-24-compatible NXP option for a new design. Consider PCAL9539A only when its Agile I/O functions add value and the firmware can accommodate the expanded feature set. TCA9539PWR is appropriate when its own electrical and register characteristics better match a fresh design. Never treat PCA9555 or PCF8575 as automatic substitutes because their address, reset, and pull-up arrangements differ.

Comparación con alternativas

Parámetro Este producto TCA9539PWR PCA9539A PCA9539PW,118 PCA9539APW,118 PCAL9539A
Package 24-TSSOP 24-TSSOP 24-TSSOP 24-TSSOP 24-TSSOP 24-TSSOP
Brand Texas Instruments Texas Instruments NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
I/O Port Count 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits
Serial Interface I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus I2C and SMBus
Interrupt Output Yes Yes Yes Yes Yes Yes
Reset Function Yes Yes Yes Yes Yes Yes
Special Features Low-power design without internal I/O pull-ups Configurable-register I/O expander More fully featured pin-to-pin replacement Base PCA9539 function in TSSOP-24 PCA9539A family in TSSOP-24 Agile I/O features

Diferenciadores clave

  • No internal I/O pull-up resistors (frente a PCA9555PW,112)
  • Dedicated hardware reset and interrupt functions (frente a PCF8575PWR)
  • Directly documented cross-brand replacement path (frente a PCA9539A)
  • 400 kHz operation with 16 configurable lines (frente a TCA9539PWR)

Notas de diseño

Route SDA and SCL as a compact, continuous bus with pull-up resistors placed near the master or the electrically appropriate end of the segment. Keep switching nodes, relay traces, and high-current return paths away from the bus to reduce injected noise. The 24-TSSOP footprint requires correct pin-1 orientation and gull-wing land patterns; review the manufacturer package drawing before finalizing the PCB footprint and solder mask.

Decouple the core and I/O supply pins separately and follow the manufacturer guidance for capacitor value and placement. Because PCA9539 I/O pins do not contain internal pull-ups, external pull-ups can create a continuous current path when an output is held low. Select resistor values from the logic voltage, leakage, transition speed, and maximum signal-loading requirements rather than copying a value without checking the actual interface.

Use the interrupt output as an edge-triggered event indication and service all pending port changes before returning to an idle state. Avoid treating the interrupt line as a level that can be ignored indefinitely. If several expanders share the bus, check address selection and confirm that each device has a unique address. Keep RESET deasserted during normal operation and define its startup state explicitly in the system power sequence.

Do not substitute PCA9555 without reviewing the address range, RESET/A2 arrangement, and missing internal I/O pull-ups. Configure unused pins as inputs or outputs according to the device's documented leakage behavior, and ensure external networks cannot back-power an unpowered I/O domain. Verify the exact register map after changing between PCA9539-family devices because similar descriptions do not guarantee identical software behavior.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The industrial temperature grade and component construction are documented, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. AEC-Q100 qualification is not applicable to the identified industrial-grade ordering code.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

PCA9539PWE4 datasheet PCA9539PWE4 pinout PCA9539PWE4 datasheet pdf PCA9539PWE4 equivalent PCA9539PWE4 replacement PCA9539PWE4 cross reference PCA9539PWE4 vs TCA9539PWR Texas Instruments PCA9539PWE4 PCA9539PWE4 24-TSSOP PCA9539PWE4 16-bit I2C expander PCA9539PWE4 400 kHz PCA9539PWE4 industrial controller PCA9539PWE4 price PCA9539PWE4 stock Where to buy PCA9539PWE4

Componentes & términos relacionados

Texas Instruments PCA9539PWE4 PCA9539 PCA9539A PCA9539PW,118 PCA9539APW,118 PCAL9539A TCA9539PWR PCA9555 PCF8575 I/O expander parallel I/O port interface IC semiconductor I2C SMBus SDA SCL interrupt output RESET 24-TSSOP TSSOP family surface mount SMD 400 kHz industrial controller PLC sensor interface low-power I/O
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ