PCA9539PWE4 - 16-Bit I2C I/O Expander | Texas Instruments
料号: PCA9539PWE4 ✓ 量产中PCA9539PWE4 概述
An I/O expander is a peripheral interface integrated circuit that connects digital input and output lines to a serial bus. Its functional hierarchy is I/O expander, bus interface controller, interface IC, and semiconductor. The PCA9539 family uses the I2C or SMBus protocol for register-based configuration and data transfer, making it suitable where adding a second parallel I/O port would otherwise require additional host pins or a separate controller.
The PCA9539PWE4 provides 16 individually configurable I/O lines, 400 kHz serial operation, interrupt output, hardware reset, and low-power behavior. Unlike the PCA9555, the PCA9539 removes the internal I/O pull-up resistors, reducing current consumption when outputs are held low. It also replaces the PCA9555 A2 address-control pin with RESET and uses a different device address range, so firmware and hardware address assignments must be reviewed carefully.
The 24-TSSOP package measures approximately 4.40 mm in body width and uses gull-wing leads. The device is offered in an industrial temperature grade. Its two supply pins support separate core and I/O voltage domains, allowing the interface to operate across systems with different logic levels when the voltage relationship remains within the device's operating requirements.
Typical uses include industrial controllers, programmable logic controllers, sensor and relay interfaces, keypad controllers, and embedded systems that need additional digital lines over a shared bus. The interrupt output allows the host to detect input changes without continuous register polling, helping reduce unnecessary serial activity. The RESET input provides a hardware mechanism for restoring the configurable registers to their default state.
PCB implementation should preserve the 24-TSSOP footprint, pin-1 orientation, bus pull-ups, supply decoupling, and accessible reset and interrupt routing. Because the I/O pins lack internal pull-ups, external resistors may be required for open-drain bus signals or inputs that must maintain a defined state. Check the manufacturer pin-description table before assigning tracks or external pull-up networks.
This product page combines the confirmed interface and package characteristics with practical implementation guidance, compatible-device comparisons, and design considerations for PCB layout, bus integrity, reset handling, and low-power I/O design.
直接替换替代料: PCA9539PWE4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCA9539PWE4 (相同外形与封装尺寸) ——差异在于 Package.
TCA9539PWR
✅ 直接替换联系询价
查看数据手册 →PCA9539A
✅ 直接替换📋 参考替代料(不在目录中)
PCA9539PW,118
✅ 直接替换📋 参考替代料(不在目录中)
PCA9539APW,118
✅ 直接替换📋 参考替代料(不在目录中)
PCAL9539A
✅ 直接替换📋 参考替代料(不在目录中)
PCA9539PWE4 规格参数
| Number of I/O Ports | 16 bits |
| 接口类型 | I2C and SMBus |
| Maximum Serial Clock Frequency | 400 kHz |
| 最大时钟频率 | 0.4 MHz |
| Number of Supply Voltages | 2 |
| 封装 | 24-pin TSSOP |
| Package Body Width | 4.40 mm |
| Package Width | 0.173 inch |
| Terminal Count | 24 |
| Lead Form | Gull wing |
| 安装方式 | Surface mount |
| Temperature Grade | Industrial |
| Interrupt Output | Yes |
| Reset Function | Yes |
| Internal I/O Pull-Up Resistors | Not fitted |
PCA9539PWE4 0.173 inch 引脚配置指南
PCA9539PWE4(0.173 inch 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9539PWE4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9539PWE4 适用于 6 应用s: Industrial Controller GPIO Expansion, PLC Digital Input and Output Module, Sensor and Relay Interface Board, Battery-Powered Sensor Node, Embedded Instrument Front Panel, General-Purpose Communication Interface.
Industrial Controller GPIO Expansion
The PCA9539PWE4 fits industrial controllers that need additional digital lines without consuming host-controller GPIO pins. A 16-bit I/O port can drive relay inputs, status LEDs, discrete enable signals, or digital sensors while the host communicates through the 2-wire I2C or SMBus interface at up to 400 kHz. The interrupt output allows the controller to react to input changes without continuously polling every port, reducing unnecessary processor activity. Because the PCA9539 has no internal I/O pull-ups, external resistors should be added wherever an input or open-drain interface requires one. Firmware should configure each port before use, verify the address assigned by A0 and A1, and preserve the separate core and I/O supply domains.
推荐
PLC Digital Input and Output Module
PCA9539PWE4 is appropriate for programmable logic controller modules requiring a compact remote I/O bank. Sixteen configurable lines can represent digital inputs, outputs, or mixed functions, while the serial interface reduces the number of traces between the controller and field-I/O circuitry. The RESET input offers a defined hardware recovery path, and the interrupt output supports event-driven handling of changed inputs. In an industrial environment, external pull-ups and protection networks should be designed around the actual field signals. Confirm the I/O supply voltage against the logic requirements, isolate exposed connector circuits as required, and validate timing between the 400 kHz bus transaction and interrupt acknowledgement.
推荐
Sensor and Relay Interface Board
The PCA9539PWE4 can concentrate digital sensor outputs and relay-control signals into one 24-TSSOP device. Input pins can monitor contact-closure or logic-level sensors, while output pins can control relay drivers or digital actuators, subject to the device's electrical limits. The interrupt line lets a host receive a prompt status change rather than polling all 16 lines continuously. Because the I/O ports do not contain internal pull-ups, use appropriate external resistors for open-collector sensors and control signals. Keep high-current or inductive loads away from the expander, place protection close to connector pins, and use a separate I/O supply when the field logic level differs from the host core voltage.
推荐
Battery-Powered Sensor Node
PCA9539PWE4 supports compact, low-power sensor nodes because it provides 16 controllable lines from a serial bus and removes the PCA9555-family internal I/O pull-ups. The reduced standby current is especially useful when external pull-up networks would otherwise hold a line high continuously. A low-power host can use the interrupt output to wake from an idle state when an attached sensor changes state. Actual battery performance depends on external pull-up values, output duty cycle, bus activity, and the selected core and I/O supply voltages. In a wearable or portable design, minimize always-connected external pull-ups and disable unused port directions through the configuration registers.
推荐
Embedded Instrument Front Panel
PCA9539PWE4 is useful in embedded instruments that need a bank of panel inputs and indicator outputs while preserving limited host-controller pins. Buttons, mode selectors, interlocks, and status LEDs can be connected through the 16-bit port, with the interrupt output notifying the host of user activity. The serial architecture also simplifies wiring compared with a direct parallel host port. Use the manufacturer pin table to preserve the interrupt and reset functions, and add external pull-ups where switches or open-drain signals require defined levels. For panel wiring exposed to electrostatic discharge or long cable runs, include suitable protection without loading the interrupt path.
推荐
General-Purpose Communication Interface
PCA9539PWE4 can provide configurable parallel lines for communication adapters, programmable control panels, and general embedded interface boards. Its 400 kHz I2C/SMBus rate supports efficient register access while the 16-bit port handles discrete signals alongside a dedicated communication controller. The separate core and I/O supply pins support mixed voltage domains when the allowed operating relationship is satisfied. Interrupt-driven input handling improves responsiveness without a full polling loop, and RESET supports deterministic startup or fault recovery. Confirm the fixed address, address pins, bus pull-up arrangement, and power sequencing during schematic review so the host can reliably discover and initialize the peripheral.
推荐
推荐产品汇总
工程参考数据: PCA9539PWE4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TCA9539PWR | PCA9539A | PCA9539PW,118 | PCA9539APW,118 | PCAL9539A |
|---|---|---|---|---|---|---|
| Package | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP | 24-TSSOP |
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| I/O Port Count | 16 bits | 16 bits | 16 bits | 16 bits | 16 bits | 16 bits |
| Serial Interface | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Interrupt Output | Yes | Yes | Yes | Yes | Yes | Yes |
| Reset Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Special Features | Low-power design without internal I/O pull-ups | Configurable-register I/O expander | More fully featured pin-to-pin replacement | Base PCA9539 function in TSSOP-24 | PCA9539A family in TSSOP-24 | Agile I/O features |
关键差异点
- No internal I/O pull-up resistors (对比 PCA9555PW,112)
- Dedicated hardware reset and interrupt functions (对比 PCF8575PWR)
- Directly documented cross-brand replacement path (对比 PCA9539A)
- 400 kHz operation with 16 configurable lines (对比 TCA9539PWR)
设计说明
Route SDA and SCL as a compact, continuous bus with pull-up resistors placed near the master or the electrically appropriate end of the segment. Keep switching nodes, relay traces, and high-current return paths away from the bus to reduce injected noise. The 24-TSSOP footprint requires correct pin-1 orientation and gull-wing land patterns; review the manufacturer package drawing before finalizing the PCB footprint and solder mask.
Decouple the core and I/O supply pins separately and follow the manufacturer guidance for capacitor value and placement. Because PCA9539 I/O pins do not contain internal pull-ups, external pull-ups can create a continuous current path when an output is held low. Select resistor values from the logic voltage, leakage, transition speed, and maximum signal-loading requirements rather than copying a value without checking the actual interface.
Use the interrupt output as an edge-triggered event indication and service all pending port changes before returning to an idle state. Avoid treating the interrupt line as a level that can be ignored indefinitely. If several expanders share the bus, check address selection and confirm that each device has a unique address. Keep RESET deasserted during normal operation and define its startup state explicitly in the system power sequence.
Do not substitute PCA9555 without reviewing the address range, RESET/A2 arrangement, and missing internal I/O pull-ups. Configure unused pins as inputs or outputs according to the device's documented leakage behavior, and ensure external networks cannot back-power an unpowered I/O domain. Verify the exact register map after changing between PCA9539-family devices because similar descriptions do not guarantee identical software behavior.
合规信息
The industrial temperature grade and component construction are documented, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. AEC-Q100 qualification is not applicable to the identified industrial-grade ordering code.