PI7C9X760CZDEX - 33Mbps I2C/SPI-UART Bridge | Diodes
MPN: PI7C9X760CZDEX ✓ সক্রিয়PI7C9X760CZDEX সারাংশ
An I2C/SPI-to-UART bridge controller is an interface IC that translates commands and data between serial protocols. The PI7C9X760 supports an I2C-bus or SPI host-side interface and provides a single high-performance UART channel, allowing existing UART peripherals, sensors, modules, or service interfaces to operate through a controller that uses a different host bus. Its position in the interface-IC hierarchy makes it useful for embedded bridges, low-power equipment, and portable or battery-operated products.
The principal features are a maximum data rate of 33Mbps, low operating and sleeping current, and as many as 8 additional programmable GPIO pins. The 64-byte TX/RX FIFO capability helps decouple host-bus activity from UART data movement. A 24-TQFN package with a 4x4 mm footprint supports compact PCB layouts, while the exposed pad provides a thermal and electrical connection to the board.
The PI7C9X760 is intended for cost-efficient, high-performance protocol conversion rather than general-purpose data processing. Configuration registers can define the bridge behavior and the available GPIOs can support discrete control or status functions. Designers should account for the 1.62V minimum operating voltage, confirm that the host bus and UART electrical limits match the system, and provide suitable bypass capacitance close to the supply and ground pins.
Typical applications include serial port expansion in embedded systems, battery-operated handheld equipment, industrial controller modules, and compact IoT devices. It can also bridge an I2C or SPI host to a UART-connected module when preserving an existing UART ecosystem is more practical than redesigning the peripheral connection.
For layout, follow the manufacturer pin-description table when assigning the 24 package pins and connect the exposed pad to the ground plane according to the datasheet land pattern. Confirm signal levels, UART baud-rate requirements, FIFO behavior, and low-power states in the manufacturer datasheet before finalizing a multi-voltage or battery-operated design.
This page consolidates the manufacturer bridge specifications, package information, interface use cases, selection guidance, and replacement constraints into a design-focused reference. It also distinguishes documented functionality from parameters that require additional engineering verification.
এর জন্য ড্রপ-ইন বিকল্প PI7C9X760CZDEX — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনPI7C9X760CZDEX সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Device Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33Mbps |
| Host-Side Interfaces | I2C-bus and SPI |
| UART Channels | 1 channel |
| TX/RX FIFO Buffer | 64 bytes |
| Programmable GPIO Count | 8 pins |
| Supply Voltage Range | 1.62V to 3.63V |
| অপারেটিং তাপমাত্রার পরিসর | -40°C to +85°C |
| প্যাকেজ | 24-TQFN (4x4 mm) |
| Package Type | VQFN with exposed pad |
| মাউন্টিং টাইপ | Surface mount |
| Moisture Sensitivity Level | MSL 1 (unlimited floor life) |
| REACH Status | REACH unaffected |
PI7C9X760CZDEX vqfn with exposed pad পিন কনফিগারেশন গাইড
PI7C9X760CZDEX (vqfn with exposed pad প্যাকেজ)-এর পিন কনফিগারেশন। এই পাওয়ার ডিভাইসে গেট, ড্রেন ও সোর্স টার্মিনাল রয়েছে। নন-পোলারাইজড প্যাকেজের ক্ষেত্রে সঠিক পিন 1 ওরিয়েন্টেশন ও ফুটপ্রিন্ট বিবরণের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সাধারণ অ্যাপ্লিকেশনগুলির মধ্যে রয়েছে পাওয়ার সাপ্লাই ডিজাইন, মোটর ড্রাইভিং এবং লোড সুইচিং।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি PI7C9X760CZDEX.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
PI7C9X760CZDEX এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Embedded Protocol Conversion, Battery-Operated Handheld Equipment, Industrial Controller Module, IoT Sensor Gateway, Serial Port Expansion, Low-Power Data Acquisition.
Embedded Protocol Conversion
The PI7C9X760CZDEX fits embedded systems that use an I2C or SPI host but must communicate with a UART peripheral. Its hardware bridge architecture removes host-side conversion logic, while the 64-byte TX/RX FIFO helps accommodate traffic bursts. The 1.62V-to-3.63V supply range also supports compact embedded systems. Designers should select host-bus and UART modes that meet the 33Mbps family capability, then implement flow control and timeout behavior appropriate to the connected device.
Battery-Operated Handheld Equipment
The PI7C9X760CZDEX is appropriate for battery-operated handheld products requiring a compact serial bridge without a discrete UART transceiver or software conversion engine. The PI7C9X760 family emphasizes low operating and sleeping current, and its 24-pin 4x4 mm TQFN package preserves board area. Up to 8 programmable GPIO pins can support control or status functions. The final power budget should include sleep-state current, active bridge current, and any external level-shifting or pull-up components.
Industrial Controller Module
An industrial controller module can use the PI7C9X760CZDEX to expose a UART peripheral to an I2C- or SPI-based processor. The specified -40°C to +85°C operating range supports many indoor and controlled industrial environments, while 64 bytes of TX/RX buffering assist with short traffic bursts. The design must still validate EMC, surge, isolation, and extended-temperature requirements at the system level rather than treating the bridge IC as a complete industrial interface solution.
IoT Sensor Gateway
The PI7C9X760CZDEX can connect a compact IoT gateway's I2C or SPI host processor to a UART-based radio, modem, or sensor module. The bridge supports rates up to 33Mbps, providing ample performance for many embedded serial links, while the exposed-pad TQFN package supports dense layouts. Firmware should define timeout, reset, and buffer-overflow behavior so the gateway remains recoverable when the attached module is absent or stops responding.
Serial Port Expansion
Use the PI7C9X760CZDEX when an embedded controller needs one additional UART channel reachable through I2C or SPI. The single-channel architecture adds a communication path without dedicating a separate host peripheral, and the FIFO buffer helps isolate the host transaction from UART timing. The board designer should account for the exposed pad, supply bypass capacitors, required pull-ups, and the logic thresholds of the peripheral when defining the expansion interface.
Low-Power Data Acquisition
The PI7C9X760CZDEX is suitable for low-power data-acquisition modules that acquire or exchange data through a UART sensor while using an I2C or SPI control path. Its low-current emphasis supports compact instrumentation, and the 24-pin 4x4 mm package minimizes connector-heavy or space-constrained layouts. Sampling behavior should be coordinated with the bridge's FIFO and interrupt functions so acquired data is transferred before a buffer limit is reached.
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা PI7C9X760CZDEX — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Package | 24-TQFN (4x4 mm), exposed pad |
| Brand | Diodes Incorporated |
| Device Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33Mbps |
| Supply Voltage Range | 1.62V to 3.63V |
| Operating Temperature Range | -40°C to +85°C |
| TX/RX FIFO Buffer | 64 bytes |
| Programmable GPIO Count | Up to 8 pins |
| Mounting Type | Surface mount |
| Moisture Sensitivity Level | MSL 1 (unlimited floor life) |
মূল পার্থক্যসমূহ
- Supports both I2C and SPI host-side connectivity (বনামGeneric single-host UART bridge)
- High-speed single-channel UART conversion (বনামGeneric low-speed UART interface)
- Integrated buffering and programmable I/O (বনামSoftware-based protocol bridge)
ডিজাইন নোট
Use the manufacturer land pattern and pin-description table for the 24-pin TQFN package. Place the required bypass capacitors close to their supply and ground pins, and connect the exposed pad using the recommended land geometry and ground-plane connection. The exposed pad is an electrical and thermal feature of the package and should not be left as an isolated copper island.
Confirm the host-bus and UART signal levels against the 1.62V-to-3.63V operating range before routing the board. Account for pull-up values, rise and fall times, bus capacitance, and any level translation between the PI7C9X760CZDEX and connected peripherals. Although the family supports rates up to 33Mbps, the selected operating mode and physical interconnect must both support the intended traffic.
Do not treat a similar 24-pin bridge as a drop-in replacement without checking pin assignments, register defaults, interrupt behavior, GPIO functions, UART polarity, and FIFO semantics. The 64-byte TX/RX FIFO and eight programmable GPIOs are functional resources, not optional decoration; changing controller type can alter timing, interrupt mapping, and host-driver requirements even when the package dimensions match.
কমপ্লায়েন্স তথ্য
The component listing identifies the device as REACH unaffected and MSL 1 (unlimited floor life). The available snippets do not provide complete, explicit classifications for RoHS, lead-free, halogen-free, or conflict-mineral status; no additional compliance claims are assumed.