PI7C9X760CZDEX - 33Mbps I2C/SPI-UART Bridge | Diodes
MPN: PI7C9X760CZDEX ✓ 啟用中PI7C9X760CZDEX 概覽
An I2C/SPI-to-UART bridge controller is an interface IC that translates commands and data between serial protocols. The PI7C9X760 supports an I2C-bus or SPI host-side interface and provides a single high-performance UART channel, allowing existing UART peripherals, sensors, modules, or service interfaces to operate through a controller that uses a different host bus. Its position in the interface-IC hierarchy makes it useful for embedded bridges, low-power equipment, and portable or battery-operated products.
The principal features are a maximum data rate of 33Mbps, low operating and sleeping current, and as many as 8 additional programmable GPIO pins. The 64-byte TX/RX FIFO capability helps decouple host-bus activity from UART data movement. A 24-TQFN package with a 4x4 mm footprint supports compact PCB layouts, while the exposed pad provides a thermal and electrical connection to the board.
The PI7C9X760 is intended for cost-efficient, high-performance protocol conversion rather than general-purpose data processing. Configuration registers can define the bridge behavior and the available GPIOs can support discrete control or status functions. Designers should account for the 1.62V minimum operating voltage, confirm that the host bus and UART electrical limits match the system, and provide suitable bypass capacitance close to the supply and ground pins.
Typical applications include serial port expansion in embedded systems, battery-operated handheld equipment, industrial controller modules, and compact IoT devices. It can also bridge an I2C or SPI host to a UART-connected module when preserving an existing UART ecosystem is more practical than redesigning the peripheral connection.
For layout, follow the manufacturer pin-description table when assigning the 24 package pins and connect the exposed pad to the ground plane according to the datasheet land pattern. Confirm signal levels, UART baud-rate requirements, FIFO behavior, and low-power states in the manufacturer datasheet before finalizing a multi-voltage or battery-operated design.
This page consolidates the manufacturer bridge specifications, package information, interface use cases, selection guidance, and replacement constraints into a design-focused reference. It also distinguishes documented functionality from parameters that require additional engineering verification.
直接替換替代品,適用於 PI7C9X760CZDEX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品PI7C9X760CZDEX 最大額定值與電氣特性
| Device Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33Mbps |
| Host-Side Interfaces | I2C-bus and SPI |
| UART Channels | 1 channel |
| TX/RX FIFO Buffer | 64 bytes |
| Programmable GPIO Count | 8 pins |
| Supply Voltage Range | 1.62V to 3.63V |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 24-TQFN (4x4 mm) |
| Package Type | VQFN with exposed pad |
| 安裝類型 | Surface mount |
| Moisture Sensitivity Level | MSL 1 (unlimited floor life) |
| REACH Status | REACH unaffected |
PI7C9X760CZDEX vqfn with exposed pad 腳位配置指南
PI7C9X760CZDEX(vqfn with exposed pad 封裝)的腳位配置。 此功率元件具有閘極、汲極與源極端子。對於非極性封裝,請參閱製造商資料表以取得確切的第 1 腳方向與佈局詳細資訊。常見應用包括電源設計、馬達驅動與負載切換。
無詳細腳位定義資料: PI7C9X760CZDEX.
請參閱 資料表 以查看完整腳位配置。
典型應用
PI7C9X760CZDEX 適用於 6 應用s: Embedded Protocol Conversion, Battery-Operated Handheld Equipment, Industrial Controller Module, IoT Sensor Gateway, Serial Port Expansion, Low-Power Data Acquisition.
Embedded Protocol Conversion
The PI7C9X760CZDEX fits embedded systems that use an I2C or SPI host but must communicate with a UART peripheral. Its hardware bridge architecture removes host-side conversion logic, while the 64-byte TX/RX FIFO helps accommodate traffic bursts. The 1.62V-to-3.63V supply range also supports compact embedded systems. Designers should select host-bus and UART modes that meet the 33Mbps family capability, then implement flow control and timeout behavior appropriate to the connected device.
Battery-Operated Handheld Equipment
The PI7C9X760CZDEX is appropriate for battery-operated handheld products requiring a compact serial bridge without a discrete UART transceiver or software conversion engine. The PI7C9X760 family emphasizes low operating and sleeping current, and its 24-pin 4x4 mm TQFN package preserves board area. Up to 8 programmable GPIO pins can support control or status functions. The final power budget should include sleep-state current, active bridge current, and any external level-shifting or pull-up components.
Industrial Controller Module
An industrial controller module can use the PI7C9X760CZDEX to expose a UART peripheral to an I2C- or SPI-based processor. The specified -40°C to +85°C operating range supports many indoor and controlled industrial environments, while 64 bytes of TX/RX buffering assist with short traffic bursts. The design must still validate EMC, surge, isolation, and extended-temperature requirements at the system level rather than treating the bridge IC as a complete industrial interface solution.
IoT Sensor Gateway
The PI7C9X760CZDEX can connect a compact IoT gateway's I2C or SPI host processor to a UART-based radio, modem, or sensor module. The bridge supports rates up to 33Mbps, providing ample performance for many embedded serial links, while the exposed-pad TQFN package supports dense layouts. Firmware should define timeout, reset, and buffer-overflow behavior so the gateway remains recoverable when the attached module is absent or stops responding.
Serial Port Expansion
Use the PI7C9X760CZDEX when an embedded controller needs one additional UART channel reachable through I2C or SPI. The single-channel architecture adds a communication path without dedicating a separate host peripheral, and the FIFO buffer helps isolate the host transaction from UART timing. The board designer should account for the exposed pad, supply bypass capacitors, required pull-ups, and the logic thresholds of the peripheral when defining the expansion interface.
Low-Power Data Acquisition
The PI7C9X760CZDEX is suitable for low-power data-acquisition modules that acquire or exchange data through a UART sensor while using an I2C or SPI control path. Its low-current emphasis supports compact instrumentation, and the 24-pin 4x4 mm package minimizes connector-heavy or space-constrained layouts. Sampling behavior should be coordinated with the bridge's FIFO and interrupt functions so acquired data is transferred before a buffer limit is reached.
工程參考資料,適用於 PI7C9X760CZDEX — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | 24-TQFN (4x4 mm), exposed pad |
| Brand | Diodes Incorporated |
| Device Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33Mbps |
| Supply Voltage Range | 1.62V to 3.63V |
| Operating Temperature Range | -40°C to +85°C |
| TX/RX FIFO Buffer | 64 bytes |
| Programmable GPIO Count | Up to 8 pins |
| Mounting Type | Surface mount |
| Moisture Sensitivity Level | MSL 1 (unlimited floor life) |
主要差異化特點
- Supports both I2C and SPI host-side connectivity (對比Generic single-host UART bridge)
- High-speed single-channel UART conversion (對比Generic low-speed UART interface)
- Integrated buffering and programmable I/O (對比Software-based protocol bridge)
設計說明
Use the manufacturer land pattern and pin-description table for the 24-pin TQFN package. Place the required bypass capacitors close to their supply and ground pins, and connect the exposed pad using the recommended land geometry and ground-plane connection. The exposed pad is an electrical and thermal feature of the package and should not be left as an isolated copper island.
Confirm the host-bus and UART signal levels against the 1.62V-to-3.63V operating range before routing the board. Account for pull-up values, rise and fall times, bus capacitance, and any level translation between the PI7C9X760CZDEX and connected peripherals. Although the family supports rates up to 33Mbps, the selected operating mode and physical interconnect must both support the intended traffic.
Do not treat a similar 24-pin bridge as a drop-in replacement without checking pin assignments, register defaults, interrupt behavior, GPIO functions, UART polarity, and FIFO semantics. The 64-byte TX/RX FIFO and eight programmable GPIOs are functional resources, not optional decoration; changing controller type can alter timing, interrupt mapping, and host-driver requirements even when the package dimensions match.
合規資訊
The component listing identifies the device as REACH unaffected and MSL 1 (unlimited floor life). The available snippets do not provide complete, explicit classifications for RoHS, lead-free, halogen-free, or conflict-mineral status; no additional compliance claims are assumed.