Diodes Incorporated

PI7C9X760CZDEX - 33Mbps I2C/SPI-UART Bridge | Diodes

料号: PI7C9X760CZDEX ✓ 量产中
1.62V to 3.63V Vdss 24-TQFN (4x4 mm) Package
最小起订量: 1 |

PI7C9X760CZDEX 概述

Diodes Incorporated PI7C9X760CZDEX is an I2C-bus/SPI-to-single-channel UART bridge controller supporting data rates up to 33Mbps, with up to 8 programmable GPIO pins and 64 bytes of TX/RX FIFO buffering. The device operates from 1.62V to 3.63V and is packaged in a 24-pin TQFN (4x4 mm) package with an exposed pad. It is designed for compact systems where a serial microcontroller or host must connect I2C or SPI peripherals to a UART interface.

An I2C/SPI-to-UART bridge controller is an interface IC that translates commands and data between serial protocols. The PI7C9X760 supports an I2C-bus or SPI host-side interface and provides a single high-performance UART channel, allowing existing UART peripherals, sensors, modules, or service interfaces to operate through a controller that uses a different host bus. Its position in the interface-IC hierarchy makes it useful for embedded bridges, low-power equipment, and portable or battery-operated products.

The principal features are a maximum data rate of 33Mbps, low operating and sleeping current, and as many as 8 additional programmable GPIO pins. The 64-byte TX/RX FIFO capability helps decouple host-bus activity from UART data movement. A 24-TQFN package with a 4x4 mm footprint supports compact PCB layouts, while the exposed pad provides a thermal and electrical connection to the board.

The PI7C9X760 is intended for cost-efficient, high-performance protocol conversion rather than general-purpose data processing. Configuration registers can define the bridge behavior and the available GPIOs can support discrete control or status functions. Designers should account for the 1.62V minimum operating voltage, confirm that the host bus and UART electrical limits match the system, and provide suitable bypass capacitance close to the supply and ground pins.

Typical applications include serial port expansion in embedded systems, battery-operated handheld equipment, industrial controller modules, and compact IoT devices. It can also bridge an I2C or SPI host to a UART-connected module when preserving an existing UART ecosystem is more practical than redesigning the peripheral connection.

For layout, follow the manufacturer pin-description table when assigning the 24 package pins and connect the exposed pad to the ground plane according to the datasheet land pattern. Confirm signal levels, UART baud-rate requirements, FIFO behavior, and low-power states in the manufacturer datasheet before finalizing a multi-voltage or battery-operated design.

This page consolidates the manufacturer bridge specifications, package information, interface use cases, selection guidance, and replacement constraints into a design-focused reference. It also distinguishes documented functionality from parameters that require additional engineering verification.

直接替换替代料: PI7C9X760CZDEX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

该产品暂无直接替换替代料。

请求替代料

PI7C9X760CZDEX 最大额定值与电气特性

Device Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33Mbps
Host-Side Interfaces I2C-bus and SPI
UART Channels 1 channel
TX/RX FIFO Buffer 64 bytes
Programmable GPIO Count 8 pins
Supply Voltage Range 1.62V to 3.63V
工作温度范围 -40°C to +85°C
封装 24-TQFN (4x4 mm)
Package Type VQFN with exposed pad
安装类型 Surface mount
Moisture Sensitivity Level MSL 1 (unlimited floor life)
REACH Status REACH unaffected

PI7C9X760CZDEX vqfn with exposed pad 引脚配置指南

PI7C9X760CZDEX(vqfn with exposed pad 封装)的引脚配置。 该功率器件具有栅极、漏极和源极端子。对于无极性封装,请参阅制造商数据手册以了解确切的引脚 1 方向和封装尺寸细节。常见应用包括电源设计、电机驱动和负载开关。

PI7C9X760CZDEX 的 vqfn with exposed pad 封装引脚图

暂无详细引脚数据: PI7C9X760CZDEX.

请参阅 数据手册 以查看完整引脚配置。

典型应用

PI7C9X760CZDEX 适用于 6 应用s: Embedded Protocol Conversion, Battery-Operated Handheld Equipment, Industrial Controller Module, IoT Sensor Gateway, Serial Port Expansion, Low-Power Data Acquisition.

🔧

Embedded Protocol Conversion

The PI7C9X760CZDEX fits embedded systems that use an I2C or SPI host but must communicate with a UART peripheral. Its hardware bridge architecture removes host-side conversion logic, while the 64-byte TX/RX FIFO helps accommodate traffic bursts. The 1.62V-to-3.63V supply range also supports compact embedded systems. Designers should select host-bus and UART modes that meet the 33Mbps family capability, then implement flow control and timeout behavior appropriate to the connected device.

📱

Battery-Operated Handheld Equipment

The PI7C9X760CZDEX is appropriate for battery-operated handheld products requiring a compact serial bridge without a discrete UART transceiver or software conversion engine. The PI7C9X760 family emphasizes low operating and sleeping current, and its 24-pin 4x4 mm TQFN package preserves board area. Up to 8 programmable GPIO pins can support control or status functions. The final power budget should include sleep-state current, active bridge current, and any external level-shifting or pull-up components.

🏭

Industrial Controller Module

An industrial controller module can use the PI7C9X760CZDEX to expose a UART peripheral to an I2C- or SPI-based processor. The specified -40°C to +85°C operating range supports many indoor and controlled industrial environments, while 64 bytes of TX/RX buffering assist with short traffic bursts. The design must still validate EMC, surge, isolation, and extended-temperature requirements at the system level rather than treating the bridge IC as a complete industrial interface solution.

🧩

IoT Sensor Gateway

The PI7C9X760CZDEX can connect a compact IoT gateway's I2C or SPI host processor to a UART-based radio, modem, or sensor module. The bridge supports rates up to 33Mbps, providing ample performance for many embedded serial links, while the exposed-pad TQFN package supports dense layouts. Firmware should define timeout, reset, and buffer-overflow behavior so the gateway remains recoverable when the attached module is absent or stops responding.

🔧

Serial Port Expansion

Use the PI7C9X760CZDEX when an embedded controller needs one additional UART channel reachable through I2C or SPI. The single-channel architecture adds a communication path without dedicating a separate host peripheral, and the FIFO buffer helps isolate the host transaction from UART timing. The board designer should account for the exposed pad, supply bypass capacitors, required pull-ups, and the logic thresholds of the peripheral when defining the expansion interface.

📟

Low-Power Data Acquisition

The PI7C9X760CZDEX is suitable for low-power data-acquisition modules that acquire or exchange data through a UART sensor while using an I2C or SPI control path. Its low-current emphasis supports compact instrumentation, and the 24-pin 4x4 mm package minimizes connector-heavy or space-constrained layouts. Sampling behavior should be coordinated with the bridge's FIFO and interrupt functions so acquired data is transferred before a buffer limit is reached.

What is the PI7C9X760CZDEX used for?
The PI7C9X760CZDEX is a single-channel I2C-bus/SPI-to-UART bridge controller designed to translate data between a host serial interface and one UART channel. According to the manufacturer datasheet, it supports rates up to 33Mbps and adds up to 8 programmable GPIO pins, making it useful for embedded protocol conversion, serial expansion, and compact battery-operated equipment.
What is the maximum data rate of the PI7C9X760CZDEX?
The PI7C9X760CZDEX supports data rates up to 33Mbps. This maximum rate is specified for the PI7C9X760 family in the Diodes Incorporated datasheet. The usable system rate remains dependent on the selected host-bus interface, UART configuration, signal integrity, firmware, and the capabilities of the connected peripheral.
What interfaces does the PI7C9X760CZDEX provide?
The PI7C9X760CZDEX provides an I2C-bus or SPI host-side interface and a single-channel UART bridge. According to the manufacturer product description, the controller also supports up to 8 additional programmable GPIO pins. This combination lets a host using one serial protocol communicate with a UART-based module without implementing the protocol conversion in software.
How much FIFO buffering is available on the PI7C9X760CZDEX?
The PI7C9X760CZDEX includes 64 bytes of TX/RX FIFO buffering. The manufacturer datasheet identifies this FIFO capacity as a feature of the bridge controller. The buffer helps accommodate bursts between the host-side transaction and UART serialization, although designers should verify the detailed flow-control and interrupt behavior for the intended protocol.
What is the supply voltage range of PI7C9X760CZDEX?
The PI7C9X760CZDEX operates from 1.62V to 3.63V. This supply-voltage range is listed for the exact PI7C9X760CZDEX ordering code and is also identified in the manufacturer datasheet. The host, UART peripheral, and pull-up network must remain compatible with the logic levels used at the bridge.
What package does the PI7C9X760CZDEX use?
The PI7C9X760CZDEX uses a 24-pin TQFN package measuring 4x4 mm and includes an exposed pad. The package is also described as V-QFN4040-24 by the manufacturer distributor listing. Use the manufacturer land-pattern and pin-description tables when assigning signals and connecting the exposed pad on the PCB.
Where can I download the PI7C9X760CZDEX datasheet PDF?
The official PI7C9X760 datasheet PDF is available from Diodes Incorporated at https://www.diodes.com/datasheet/download/PI7C9X760.pdf. The document contains the family-level electrical characteristics, register information, application guidance, and package details needed to evaluate the PI7C9X760CZDEX ordering code.
Where is the PI7C9X760CZDEX pinout located?
The PI7C9X760CZDEX pinout is located in the pin-description table and package drawings of the official Diodes Incorporated PI7C9X760 datasheet. The device is a 24-pin TQFN with an exposed pad, so PCB work should use the manufacturer diagram for both numbered pins and the thermal-pad connection rather than inferring assignments from another package variant.
Can the PI7C9X760CZDEX be used in battery-operated devices?
Yes, the PI7C9X760CZDEX is suitable for battery-operated and handheld systems because the PI7C9X760 family emphasizes low operating and sleeping current. The manufacturer also identifies cost-efficient, battery-operated equipment as a target application. Actual battery-life performance still depends on the selected operating state, UART activity, GPIO loading, and system power architecture.
What is the operating temperature range of PI7C9X760CZDEX?
The PI7C9X760CZDEX is specified for -40°C to +85°C. This operating-temperature range applies to the exact ordering code shown in the component listing. Designs operating near either endpoint should also account for voltage tolerance, package stress, and the temperature limits of the connected UART peripheral.
Is the PI7C9X760CZDEX compatible with a 1.8V system?
The PI7C9X760CZDEX supports a 1.62V to 3.63V supply range, so it can operate from a regulated 1.8V rail. The interface voltage levels still must be compatible with the host, GPIO, and UART-connected circuitry. Confirm pull-up requirements and signal thresholds in the manufacturer datasheet before finalizing the board.
How does the PI7C9X760CZDEX compare with a software UART bridge?
The PI7C9X760CZDEX performs I2C/SPI-to-UART protocol conversion in hardware, supports rates up to 33Mbps, and includes 64 bytes of TX/RX FIFO buffering. A software bridge can reduce hardware cost but consumes processor time and firmware complexity. This controller is preferable when interface timing, concurrency, or deterministic service of multiple attached devices is important.
When should I choose the PI7C9X760CZDEX instead of a generic UART bridge?
Choose the PI7C9X760CZDEX when the system needs both I2C and SPI host options, a UART channel rated for data rates up to 33Mbps, up to 8 programmable GPIOs, and a compact 24-TQFN footprint. It is especially useful in embedded equipment that must connect a UART peripheral to an I2C- or SPI-based controller without implementing protocol conversion in host firmware.
Is the PI7C9X760CZDEX suitable for industrial controller modules?
The PI7C9X760CZDEX is suitable for industrial controller modules requiring an embedded protocol bridge, especially where its -40°C to +85°C operating range, 1.62V-to-3.63V supply range, and hardware FIFO support are useful. The exact industrial qualification status is not stated, so system-level environmental and reliability requirements must be evaluated separately.
What is the best drop-in replacement for PI7C9X760CZDEX?
No verified drop-in replacement for PI7C9X760CZDEX was identified in the available cross-reference results. A valid replacement must match the 24-TQFN footprint, pin assignments, supply range, interface behavior, FIFO architecture, and 33Mbps performance target. Use the Request a Quote form on this page to discuss exact-source availability, and do not substitute a controller solely because it uses a similar package.
Where can I buy PI7C9X760CZDEX and check its lead time?
Use the Request a Quote form on this page to request the current price, stock position, lead time, and order quantity for PI7C9X760CZDEX. The exact component is offered in a 24-TQFN tape-and-reel ordering configuration, but current commercial availability should be confirmed at quotation time because inventory and production schedules can change.

工程参考数据: PI7C9X760CZDEX ——对比、设计指导和合规信息。

选型指南

Choose the PI7C9X760CZDEX when an embedded system needs a compact, hardware-based bridge between an I2C or SPI host and one UART peripheral, particularly when high serial rates or low-power operation are important. Its 33Mbps capability, 64-byte TX/RX FIFO, and eight programmable GPIOs provide useful resources for battery-operated equipment, IoT modules, and compact controller boards. Verify that the 1.62V-to-3.63V supply range and UART signal levels match the system, and use the manufacturer pin table for the 24-TQFN layout. Do not choose a substitute solely by package size: a valid drop-in alternative must preserve pin assignments, protocol behavior, register access, FIFO operation, interrupt mapping, and electrical limits. If exact-source continuity is more important than an alternate supplier, request a quote for the PI7C9X760CZDEX and confirm availability before committing the design.

与替代料对比

参数 本产品
Package 24-TQFN (4x4 mm), exposed pad
Brand Diodes Incorporated
Device Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33Mbps
Supply Voltage Range 1.62V to 3.63V
Operating Temperature Range -40°C to +85°C
TX/RX FIFO Buffer 64 bytes
Programmable GPIO Count Up to 8 pins
Mounting Type Surface mount
Moisture Sensitivity Level MSL 1 (unlimited floor life)

关键差异点

  • Supports both I2C and SPI host-side connectivity (对比 Generic single-host UART bridge)
  • High-speed single-channel UART conversion (对比 Generic low-speed UART interface)
  • Integrated buffering and programmable I/O (对比 Software-based protocol bridge)

设计说明

Use the manufacturer land pattern and pin-description table for the 24-pin TQFN package. Place the required bypass capacitors close to their supply and ground pins, and connect the exposed pad using the recommended land geometry and ground-plane connection. The exposed pad is an electrical and thermal feature of the package and should not be left as an isolated copper island.

Confirm the host-bus and UART signal levels against the 1.62V-to-3.63V operating range before routing the board. Account for pull-up values, rise and fall times, bus capacitance, and any level translation between the PI7C9X760CZDEX and connected peripherals. Although the family supports rates up to 33Mbps, the selected operating mode and physical interconnect must both support the intended traffic.

Do not treat a similar 24-pin bridge as a drop-in replacement without checking pin assignments, register defaults, interrupt behavior, GPIO functions, UART polarity, and FIFO semantics. The 64-byte TX/RX FIFO and eight programmable GPIOs are functional resources, not optional decoration; changing controller type can alter timing, interrupt mapping, and host-driver requirements even when the package dimensions match.

合规信息

RoHS
Unknown
REACH
Compliant
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The component listing identifies the device as REACH unaffected and MSL 1 (unlimited floor life). The available snippets do not provide complete, explicit classifications for RoHS, lead-free, halogen-free, or conflict-mineral status; no additional compliance claims are assumed.

数据核验日期: 2026-11-16 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

PI7C9X760CZDEX datasheet PI7C9X760CZDEX datasheet pdf PI7C9X760CZDEX pinout PI7C9X760CZDEX equivalent PI7C9X760CZDEX replacement PI7C9X760CZDEX cross reference PI7C9X760CZDEX footprint PI7C9X760CZDEX price PI7C9X760CZDEX stock Diodes Incorporated PI7C9X760CZDEX PI7C9X760 33Mbps UART bridge PI7C9X760 24-TQFN pinout

相关元器件 & 术语

Diodes Incorporated PI7C9X760CZDEX PI7C9X760 I2C-bus/SPI-to-UART bridge controller bridge controller interface IC semiconductor I2C SPI UART TX/RX FIFO GPIO 33Mbps data rate 1.62V to 3.63V supply voltage 24-TQFN VQFN family 4x4 mm package exposed pad surface mount MSL 1 REACH battery-operated equipment IoT gateway industrial controller
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情