SI3010-F-FS 2.4 kbps Line-Side DAA | Skyworks
MPN: SI3010-F-FS ✓ সক্রিয়SI3010-F-FS সারাংশ
A direct access arrangement, or DAA, is the telephone-network-facing interface that isolates the modem electronics from the analog telephone line. In a complete ISOmodem design, the DAA handles line-side signaling and protection while the companion modem IC performs data modulation and demodulation. This division allows a compact, globally programmable telephone-line interface to be paired with the appropriate Silicon Labs modem family member.
The documented SI3010 feature set covers modem formats including ITU-T and Bell rates from 300 bps through 56 kbps, V.21, V.22, V.29, Fast Connect, V.44, V.42, V.42bis, and MNP2-5. It also supports automatic rate negotiation and Type I and Type II caller-ID decoding. These capabilities apply to the shared Si2457, Si2454, Si2415, and Si2404 ISOmodem documentation identified for the component.
The SI3010 is built for 3 V operation and is listed with a 0 °C to 70 °C commercial temperature range. It belongs to the telecom-interface IC category and uses surface-mount SOIC construction, allowing conventional reflow assembly and automated inspection. Because a DAA is connected directly to an analog telephone line, its surrounding protection, isolation, filtering, and ring-detection circuitry are as important as the IC itself.
Typical implementations include Si2404-based voice and data modems, embedded fax or data systems, caller-ID equipment, and industrial telephone-line interfaces. The Si2457, Si2454, Si2415, and Si2401 devices provide practical companion choices when a complete two-chip ISOmodem system is required rather than the DAA alone.
Designers should preserve the separation between telephone-line and logic domains, validate the external protection network, and confirm the companion modem’s recommended hook-state, ring-detection, and line-driver circuitry. The manufacturer datasheet should be used for the exact pin assignments, absolute maximum ratings, timing, and reference circuit because the line-side interface is sensitive to component values and printed-circuit-board layout.
This page combines the verified MPN, package and interface information with drop-in comparison guidance, design notes, application fit, and practical sourcing questions. It is intended to help engineers identify the correct line-side DAA and plan a robust ISOmodem-based telephone interface.
এর জন্য ড্রপ-ইন বিকল্প SI3010-F-FS — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible SI3010-F-FS (একই form factor এবং footprint) — পার্থক্য রয়েছে Lifecycle Status, Mounting Type, Product Type.
SI3010-F-FSR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
SI3010-FS
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →SI3010-F-FS-R
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
SI3010-F-FS বিশেষণ
| কোনো স্পেসিফিকেশন পাওয়া যায়নি |
SI3010-F-FS standard পিন কনফিগারেশন গাইড
SI3010-F-FS (standard প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি SI3010-F-FS.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
SI3010-F-FS এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Si2404 Voice and Data Modem, Caller-ID Telephone Equipment, Industrial Telephone-Line Data Terminal, Embedded Fax and Data Terminal, Legacy Telephone Network Gateway, Remote Monitoring and Telemetry Link.
Si2404 Voice and Data Modem
The SI3010-F-FS fits the line-side portion of an Si2404 ISOmodem because it is specifically identified as the direct access arrangement for that platform. Operating from a 3 V rail at 2400 bps, it provides the telephone-network interface while the companion modem handles modulation and demodulation. The documented ISOmodem feature set includes automatic rate negotiation, ITU-T and Bell formats from 300 bps to 56 kbps, and Type I and Type II caller-ID decoding. Designers should reproduce the manufacturer reference network and validate the external protection, ring-detection, and hook-state components against the final line configuration.
সুপারিশকৃত
Caller-ID Telephone Equipment
The SI3010-F-FS is appropriate for caller-ID products that require Type I and Type II caller-ID decoding alongside ordinary telephone-line modem operation. Its 3 V supply and 2400 bps DAA function support compact line-interface implementations, while automatic rate negotiation helps negotiate supported modem rates. The IC is normally paired with a Si2404-class modem rather than used as a standalone data modem. In a finished product, firmware, hook-state logic, ring detection, and the line protection network must be validated together to obtain reliable caller-ID operation across the intended telephone networks.
সুপারিশকৃত
Industrial Telephone-Line Data Terminal
A remote monitoring terminal requiring a telephone-line connection can use the SI3010-F-FS as the line-side interface for a Si2404-based modem path. The 3 V DAA supports the associated 2400 bps operating mode and shares documentation covering V.21, V.22, V.29, Fast Connect, V.44, V.42, V.42bis, and MNP2-5 formats. This makes it useful where legacy analog infrastructure must be retained. Industrial deployments should include reviewed surge protection, isolation boundaries, controlled ring and hook behavior, and environmental testing across the device's documented 0 °C to +70 °C operating range.
সুপারিশকৃত
Embedded Fax and Data Terminal
The SI3010-F-FS can provide the telephone-line interface in an embedded fax or low-speed data terminal that uses the Si2404 ISOmodem architecture. At 3 V and 2400 bps, it complements the modem chipset while supporting the broader format set documented for the shared ISOmodem family. The compact 16-pin SOIC package supports surface-mount assembly, but analog telephone-line designs still require careful separation of external protection components from sensitive logic. Confirm the exact pin functions and reference values in the manufacturer datasheet before adapting an existing board, particularly when changing among SI3010 ordering suffixes.
সুপারিশকৃত
Legacy Telephone Network Gateway
The SI3010-F-FS can serve as the line-side DAA in a gateway that bridges legacy analog telephone lines and an embedded digital controller. The DAA's 2400 bps operating mode and automatic rate negotiation are suitable for basic control or supervisory links, while the associated documentation covers Bell and ITU-T formats plus caller-ID decoding. A robust gateway must preserve the analog isolation and protection architecture specified by the reference design. System-level validation should cover ring cadence, line seizure and release, caller-ID timing, noise immunity, and behavior across the documented 0 °C to +70 °C temperature range.
সুপারিশকৃত
Remote Monitoring and Telemetry Link
Remote telemetry equipment that must communicate over an analog telephone line can use the SI3010-F-FS with the Si2404 modem to create a compact 2400 bps connection. The DAA's 3 V operation reduces the number of supply rails required around the modem, while automatic rate negotiation can improve connection setup behavior. This application is especially relevant to sites without modern network connectivity. The external line interface remains the critical design area: use the manufacturer reference network, maintain the intended isolation geometry, verify protection-component ratings, and test connection establishment and data integrity under varying line conditions.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা SI3010-F-FS — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | SI3010-F-FSR | SI3010-FS | SI3010-F-FS-R |
|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions |
| Product Type | Line-side Direct Access Arrangement (DAA) | Line-side Direct Access Arrangement (DAA) | SI3010 line-side DAA | SI3010-F-FS ordering variant |
| Supply Voltage | 3 V | 3 V | 3 V | 3 V |
মূল পার্থক্যসমূহ
- Documented direct replacement path (বনামSI3010-F-FSR)
- Defined line-side role for Si2404 ISOmodem (বনামSI3010-FS)
- Same documented DAA operating class (বনামSI3010-F-FS-R)
ডিজাইন নোট
Treat the SI3010-F-FS telephone-line side as a sensitive analog interface. Place its protection and filtering components close to the line connector and maintain the isolation geometry used in the manufacturer reference design. Keep digital modem and control traces away from high-energy ring and surge paths. Because the search excerpts do not provide the complete pin table, verify every connection against the manufacturer datasheet before assigning PCB tracks or checking continuity.
Do not substitute the SI3010-F-GS merely because its name is similar: a comparison identifies that device with an 8-pin SOIC package, whereas SI3010-F-FS is listed as 16-pin SOIC. Pin-compatible substitutions include SI3010-F-FSR and related suffix variants, but every ordering code must still be checked against the current ordering guide. Also verify tube versus reel configuration and exposed-pad requirements before approving a replacement.
The SI3010-F-FS operates from a 3 V supply. Provide a stable 3 V rail with low impedance near the device and decouple according to the manufacturer reference circuit. Avoid routing telephone-side surge current through digital return paths, and verify the power-supply startup sequence against hook-state and reset requirements. The available excerpts do not state absolute maximum voltage, current consumption, or decoupling values, so those figures must be taken directly from the datasheet.
Validate hook-state, ring detection, and caller-ID timing in the complete modem system rather than treating them as isolated digital signals. Use the reference values and ringing network shown in the associated Si2457, Si2454, Si2415, and Si2404 documentation. Confirm whether the selected companion modem requires a particular line-side DAA ordering suffix, since firmware assumptions and suffix-specific ordering rules can affect otherwise similar boards.
কমপ্লায়েন্স তথ্য
The available product excerpts do not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable because the SI3010-F-FS is specified for a 0 °C to +70 °C commercial temperature range rather than as an automotive-qualified device.