Texas Instruments

TLV2461ID - 6V 6.4MHz RRIO Op Amp | Texas Instruments

MPN: TLV2461ID ✓ সক্রিয়
2.7 V to 6 V Vdss 1.3 nA Id 8-pin SOIC Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

TLV2461ID সারাংশ

Texas Instruments TLV2461ID is a single-circuit operational amplifier designed for low-power, rail-to-rail input and output operation from a 2.7 V to 6 V supply. Its 6.4 MHz gain-bandwidth product, 80 mA output capability, 66 dB instrumentation gain, and 0.075 µA quiescent current make it suitable for portable instrumentation, sensor interfaces, battery-powered equipment, and general signal-conditioning systems. The device is packaged in an 8-pin SOIC.

An operational amplifier is an analog IC that amplifies the voltage difference between its differential inputs. A rail-to-rail input/output, or RRIO, amplifier can accept input signals near the positive and negative supply rails and produce output swings close to those rails. This makes the TLV2461 useful in systems whose signal range would exceed the usable input or output range of a conventional amplifier tied closely to its supply rails.

The TLV2461ID combines a 6.4 MHz gain-bandwidth product with a low 0.075 µA quiescent current. According to the Texas Instruments product page, it is a single amplifier operating from 2.7 V to 6 V. Its input bias current of 1.3 nA is suited to high-impedance sources, while the listed 80 mA per-channel output current provides useful drive capability for typical analog stages. The amplifier also supports input and output operation across the supply rails.

With a reported instrumentation gain of 66 dB, the device can be used in instrumentation and measurement circuits requiring moderate signal amplification. Its 6.4 MHz bandwidth supports higher-frequency feedback networks than a low-frequency precision amplifier. The SOIC-8 package is suitable for conventional PCB assembly, and the single-amplifier configuration provides a straightforward implementation for buffer, amplifier, comparator-style, and general-purpose analog applications.

Typical applications include portable sensor conditioning, battery-operated measurement instruments, industrial low-power interfaces, audio and communication control paths, precision current-voltage conversion, and low-leakage photodiode front ends. The 1.3 nA input bias current is particularly relevant when the source impedance is high enough that amplifier input current materially changes the measured voltage.

Designers should verify signal amplitude, output swing, input common-mode range, noise, and stability at the intended gain. Decoupling capacitors should be placed close to the supply pins, while high-impedance input nodes require short traces and guarded layouts to reduce leakage and interference pickup.

This page combines the Texas Instruments device specifications with package guidance, application-oriented engineering notes, and same-package replacement options for engineers planning a TLV2461ID-based analog circuit.

এর জন্য ড্রপ-ইন বিকল্প TLV2461ID — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible TLV2461ID (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Amplifier Type, Input Common-Mode Range, Operating Temperature Range.

Texas Instruments
Amplifier Type: Dual operational amplifier
Input Common-Mode Range: Rail-to-rail input
Operating Temperature Range: -40 °C to +125 °C
এর সাথে তুলনা করুন TLV2461ID →
Texas Instruments
Package: 14-pin SOIC (D)
Input Common-Mode Range: Extends beyond the supply rails
Operating Temperature Range: -40 C to +85 C
এর সাথে তুলনা করুন TLV2461ID →

TLV2461CD

✅ ড্রপ-ইন
📦 8-SOIC
Same 8-pin SOIC, 1-channel topology, and 6.4 MHz class; ordering-grade and temperature details must be confirmed

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TLV2461QDR

✅ ড্রপ-ইন
📦 8-SOIC
Same 8-pin SOIC and principal performance characteristics; automotive-qualified ordering designation

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TLV2460CDR

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
📦 8-SOIC
Same 8-pin SOIC family and approximately 6.4 MHz class, but the TLV2460 family variant includes shutdown functionality

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TLV2462ID

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
Texas Instruments
📦 8-SOIC
Dual operational amplifier · 2 circuits · 6.4 MHz · 1.6 V/µs · 6 V · Rail-to-rail input · Rail-to-rail output

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TLV2464ID

✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়
Texas Instruments
📦 8-SOIC
4 channels · 6 V · 6.4 MHz · Rail-to-rail input · Rail-to-rail output · 80 mA · 500 uA/channel · Extends beyond the supply rails

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

TLV2461ID সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Amplifier Type Single operational amplifier
Number of Channels 1 circuit
Rail-to-Rail Architecture Input and output (RRIO)
Supply Voltage Range 2.7 V to 6 V
Nominal Supply Voltage 6 V
Gain-Bandwidth Product 6.4 MHz
Input Bias Current 1.3 nA
কুইসেন্ট কারেন্ট 0.075 µA per amplifier
Output Current per Channel 80 mA
Instrumentation Gain 66 dB
Output Swing Range -1.35 V to +3 V at a 3 V supply
প্যাকেজ 8-pin SOIC
পিন সংখ্যা 8 pins
মাউন্টিং টাইপ Surface mount
Product Classification Standard general-purpose amplifier

TLV2461ID পিন কনফিগারেশন

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
পিন 1 OUT — Amplifier output
পিন 2 V- — Negative supply connection
পিন 3 +IN — Noninverting input
পিন 4 -IN — Inverting input
পিন 5 NC — Not connected
পিন 6 NC — Not connected
পিন 7 V+ — Positive supply connection
পিন 8 NC — Not connected

সাধারণ ব্যবহার

TLV2461ID এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Sensor Conditioning, Precision Current-Voltage Conversion, Industrial Low-Power Instrumentation, Photodiode and High-Impedance Signal Detection, Portable Audio Signal Conditioning, Communication and Interface Buffers.

🔋

Battery-Powered Sensor Conditioning

The TLV2461ID fits low-energy sensor front ends that operate from a 2.7 V to 6 V supply. Its 0.075 µA quiescent current limits the amplifier's standing consumption, while the 1.3 nA input bias current reduces loading error when a high-impedance sensor or resistive divider is used. The device can amplify the sensor voltage and drive the input of a converter, comparator, or low-power controller. Its 6.4 MHz gain-bandwidth product also leaves bandwidth margin for modest filtering and gain stages. Care is still required around battery-powered boards because leakage through the sensor, PCB surfaces, and protection components can exceed the amplifier bias current.

⚡

Precision Current-Voltage Conversion

The TLV2461ID is suitable for transimpedance and general current-to-voltage stages where the input source must not be disturbed. Its 1.3 nA input bias current creates a small error term in high-impedance feedback networks, while the 6.4 MHz gain-bandwidth product supports feedback networks beyond very-low-frequency operation. An engineer can connect the amplifier as a transimpedance stage or precision noninverting amplifier and place a limiting resistor or diode strategy according to the signal source. Stable compensation and parasitic capacitance control remain critical, particularly when feedback resistance is high and the source is capacitive.

🏭

Industrial Low-Power Instrumentation

The TLV2461ID provides a compact single-amplifier solution for industrial instrumentation operating between 2.7 V and 6 V. Its 66 dB instrumentation gain and 1.3 nA input bias current support measurement chains that process weak sensor outputs without excessive loading. The SOIC-8 package is practical for conventional industrial PCB assembly, and the 6.4 MHz gain-bandwidth product supports faster feedback networks than an ultra-low-frequency precision amplifier. For field equipment, engineers should verify temperature limits, noise performance, creepage requirements, and protection-network leakage against the exact environmental requirements.

📷

Photodiode and High-Impedance Signal Detection

The TLV2461ID can serve as the first active stage in a photodiode or high-impedance detector because its 1.3 nA input bias current is small relative to the currents produced by many optical sensors. Combined with a 6.4 MHz gain-bandwidth product, it supports transimpedance amplification where response speed must exceed that of a very-low-bandwidth precision device. The PCB should protect the input node from humidity, contamination, and surface leakage because those effects can dominate at the same current scale. Feedback resistance, input capacitance, stray capacitance, and amplifier stability should be evaluated together.

🎧

Portable Audio Signal Conditioning

The TLV2461ID can condition low-level audio or control signals in portable equipment operating from 2.7 V to 6 V. Its RRIO architecture supports input and output operation closer to the supply rails, which is valuable when the available signal range is a significant fraction of the supply voltage. The 80 mA per-channel output-current rating provides more drive capability than the very-low quiescent current might suggest, while the 6.4 MHz gain-bandwidth product supports moderate audio-frequency feedback networks. Output loading, distortion, noise, and stability should be checked at the selected gain and whether headroom is available for output-swing requirements.

🌐

Communication and Interface Buffers

The TLV2461ID is usable as a low-power buffer or interface amplifier in communication equipment where signals must be referenced to a 2.7 V to 6 V rail. Rail-to-rail input and output behavior provides useful signal range for low-voltage systems, while the 6.4 MHz gain-bandwidth product permits closed-loop configurations with appreciable bandwidth. A unity-gain buffer application requires confirmation that the capacitive and resistive load falls within the stable operating region. For longer traces or cable-driven nodes, input and output protection, impedance matching, and physical distance from switching circuitry are as important as the amplifier's nominal bandwidth.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

TLV2461CD Same-package low-power amplifier option ব্যবহৃত হয়: Battery-Powered Sensor Conditioning, Industrial Low-Power Instrumentation, Photodiode and High-Impedance Signal Detection, Communication and Interface Buffers TLV2462ID Texas Instruments ব্যবহৃত হয়: Battery-Powered Sensor Conditioning, Photodiode and High-Impedance Signal Detection, Communication and Interface Buffers TLV2464ID Texas Instruments ব্যবহৃত হয়: Precision Current-Voltage Conversion, Portable Audio Signal Conditioning TLV2461QDR Automotive-qualified same-package option ব্যবহৃত হয়: Precision Current-Voltage Conversion, Portable Audio Signal Conditioning TLV2460CDR Shutdown-capable same-package family option ব্যবহৃত হয়: Industrial Low-Power Instrumentation
What is the operating voltage of TLV2461ID?
The TLV2461ID operates from 2.7 V to 6 V according to the Texas Instruments product page and manufacturer datasheet. This range supports 3 V and 5 V systems while accommodating supply variation around the nominal rail. The listed output swing of approximately -1.35 V to +3 V at a 3 V supply should be considered when the circuit requires output levels close to either rail.
What are the key specifications of TLV2461ID that engineers should know?
The TLV2461ID is a single 6.4 MHz RRIO operational amplifier with an 80 mA output current rating, 1.3 nA input bias current, 0.075 µA quiescent current, and 66 dB instrumentation gain. According to the Texas Instruments product page, it operates from 2.7 V to 6 V in an 8-pin SOIC package. These parameters position it between low-frequency precision-oriented amplifiers and higher-bandwidth general-purpose devices.
Where can I download the TLV2461ID datasheet PDF?
The official TLV2461ID datasheet is available from the Texas Instruments product page through the manufacturer document link at https://www.ti.com/lit/gpn/TLV2461. Use that document for the authoritative electrical characteristics, ordering information, pin configuration, and application guidance. The distributor PDF link may reproduce the same document, but the TI-hosted version is preferable for revision control and future updates.
Where can I find the TLV2461ID pinout?
The TLV2461ID pinout is shown in the Texas Instruments TLV2461 datasheet under the pin configuration or package information. The device uses an 8-pin SOIC with pins 1 through 8 arranged counterclockwise from the package marker. Assign PCB nets using the manufacturer pin table, particularly when using a no-connect position in a non-inverting or inverting amplifier configuration.
Is TLV2461ID suitable for battery-powered sensor interfaces?
Yes, the TLV2461ID is suitable for battery-powered sensor interfaces because it operates from 2.7 V to 6 V and has a low 0.075 µA quiescent current. Its 1.3 nA input bias current also helps preserve the accuracy of high-source-impedance sensor signals. The 6.4 MHz bandwidth provides useful response margin for moderately fast conditioning stages without requiring a high-speed, higher-current amplifier.
What can replace TLV2461ID without changing the PCB?
The TLV2461CD and TLV2461QDR are same-package Texas Instruments alternatives identified as having consistent terminals, packages, and principal performance characteristics. The TLV2461CD is an 8-pin SOIC variant, while the QDR designation identifies the automotive-qualified ordering option. Confirm the exact grade, temperature range, enable behavior, and lifecycle requirements in the manufacturer datasheet before approving either replacement.
Is TLV2461ID the same as TLV2461CD?
The TLV2461ID and TLV2461CD are closely related 8-pin SOIC versions of the TLV2461 amplifier. Cross-reference information describes their terminals, package, and principal performance characteristics as consistent, indicating direct board-level substitutability. The ordering suffixes can still denote different grade, temperature, or qualification options, so confirm the suffix-specific ordering table before production use.
When should I choose TLV2461ID over TLV2461CD?
Choose TLV2461ID when its suffix-specific qualification and environmental requirements match the design, and choose TLV2461CD when that ordering option better fits the production program. The two parts use the same 8-pin SOIC format and are described as having consistent electrical and package characteristics. The decision should be based on the manufacturer ordering table rather than on the suffix alone.
TLV2461ID vs TLV2461QDR: which is better for automotive use?
TLV2461QDR is the automotive-qualified ordering option and is generally the appropriate choice for an automotive program requiring that qualification. The TLV2461ID is the standard catalog ordering option. Both are based on the 8-pin SOIC TLV2461 family and are described as having consistent package and principal performance characteristics, but qualification requirements should be checked against the manufacturer ordering information.
What is the best cross-brand equivalent for TLV2461ID?
No cross-brand equivalent is established here because the cross-reference results did not identify a specific competing manufacturer part with verified package, pinout, supply range, bandwidth, and parameter compatibility. A replacement should not be selected from a generic similarity listing alone. Use the manufacturer cross-reference and distributor cross-reference tools to locate candidates, then verify all electrical and mechanical requirements before treating any candidate as a drop-in replacement.
How much bandwidth does TLV2461ID provide?
The Texas Instruments product page lists a 6.4 MHz gain-bandwidth product for the TLV2461 family. This bandwidth supports feedback-based amplifier configurations beyond the low-frequency range of micropower precision amplifiers. Actual closed-loop bandwidth depends on the selected noise gain, amplifier stability, load, and external components, so the 6.4 MHz figure should be used as the device gain-bandwidth parameter rather than an unconditional closed-loop bandwidth.
What is the quiescent current of TLV2461ID?
The TLV2461ID has a listed quiescent current of 0.075 µA per amplifier. According to the Texas Instruments product page and datasheet family information, this low operating current supports low-power signal-conditioning designs. Total system consumption still depends on the operating mode, load, divider networks, leakage paths, and any additional circuitry connected to the amplifier.
Does TLV2461ID support rail-to-rail input and output?
Yes, the TLV2461 is described by Texas Instruments as a rail-to-rail input/output, or RRIO, operational amplifier. The architecture allows input and output operation nearer the supply rails than a conventional amplifier with restricted common-mode or output ranges. Actual usable swing still depends on supply voltage, load, output current, and the limits identified in the manufacturer datasheet.
Where to buy TLV2461ID online?
Use the Request a Quote form on this page to request TLV2461ID availability, current lead time, and a quotation for the required quantity. The part is an 8-pin SOIC single operational amplifier in the Texas Instruments TLV2461 family. The form is the appropriate route for obtaining an orderable quotation without relying on a stale third-party price or inventory indication.
What is the price of TLV2461ID?
The current TLV2461ID quotation is available through the Request a Quote form on this page. Pricing depends on order quantity, package suffix, sourcing volume, and current market conditions. The structured pricing area on the product page is the authoritative source for any commercial response, while the manufacturer part number to quote is TLV2461ID.
What is the lead time and stock status for TLV2461ID?
Request the current TLV2461ID stock status, lead time, and minimum order quantity through the Request a Quote form on this page. Texas Instruments identifies TLV2461ID as an 8-pin SOIC ordering option within the TLV2461 amplifier family. Supply status can change, so purchasing teams should request confirmation for the exact suffix and quantity rather than rely on a general catalog indication.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TLV2461ID — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose TLV2461ID for low-voltage, low-power signal conditioning where a single 2.7 V to 6 V amplifier must combine 6.4 MHz bandwidth, 1.3 nA input bias current, and an 8-pin SOIC footprint. Choose TLV2461QDR when the same electrical and package arrangement is needed for an automotive-qualified design. Choose TLV2461CD when that ordering option satisfies the required environmental grade and manufacturing program. Choose TLV2460CDR or TLV2462ID only when the additional shutdown function is useful, after confirming the associated control and current behavior. Choose TLV2464ID when stronger output-drive capability is more valuable than retaining the TLV2461ID's 80 mA per-channel rating. No cross-brand drop-in candidate is approved without a separate package, pinout, and parametric review.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য TLV2461CD TLV2461QDR TLV2460CDR TLV2462ID TLV2464ID
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Special Feature RRIO, no shutdown RRIO, no shutdown Automotive-qualified RRIO option Shutdown-capable family variant Shutdown-capable family variant Higher-output-current family variant

মূল পার্থক্যসমূহ

  • Combines low quiescent current with higher bandwidth (বনামTLV2460CDR)
  • Automotive-qualified family option without changing the footprint (বনামTLV2461CD)
  • Low input bias current for high-impedance conditioning (বনামTLV2464ID)

ডিজাইন নোট

Place the positive and negative supply bypass capacitors immediately beside pins 7 and 2, with short ground returns and minimal loop area. For a single 8-pin SOIC, the pin-2 and pin-7 locations can make short direct routes difficult, so route the capacitors before considering long interconnects. Keep the exposed input and feedback nodes away from switching nodes, inductors, and high-current return paths.

Do not assume that rail-to-rail operation provides unlimited output swing. The listed output range of approximately -1.35 V to +3 V at a 3 V supply is materially narrower than the physical rails. Check the required waveform amplitude and load current, and leave sufficient headroom for distortion and transient requirements. The same caution applies when interpreting RRIO input behavior at the limits of the supply range.

For high-impedance sensor inputs, use the lowest practical feedback resistance and keep the sensitive node physically small. The 1.3 nA input bias current is favorable, but PCB contamination, humidity, protection-device leakage, and adjacent high-impedance nets can still dominate the error. Guarding and a clean surface finish may be more valuable than further amplifier optimization when the source impedance is extremely high.

The 0.075 µA quiescent current makes battery operation attractive, but system-level leakage can dominate. Include divider currents, protection leakage, sensor impedance, and shutdown-state behavior in the power budget. Measure the complete analog front end at the intended supply voltage, temperature, and signal state rather than treating the amplifier's quiescent current as the total standby consumption.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The TLV2461QDR ordering option is described as automotive-qualified, but separate RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established for TLV2461ID.

ডেটা যাচাই করা হয়েছে: 2026-11-15 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

TLV2461ID datasheet TLV2461ID pinout TLV2461ID datasheet pdf TLV2461ID equivalent TLV2461ID replacement TLV2461ID cross reference TLV2461ID vs TLV2461QDR TLV2461ID footprint TLV2461ID application circuit Texas Instruments TLV2461ID TLV2461ID price TLV2461ID stock 6V 6.4MHz RRIO op amp

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments TLV2461ID TLV2461 TLV2461CD TLV2461QDR TLV2460CDR TLV2462ID TLV2464ID operational amplifier single amplifier rail-to-rail input/output RRIO gain-bandwidth product input bias current quiescent current instrumentation gain SOIC-8 surface-mount package signal conditioning battery-powered instrumentation transimpedance amplifier sensor interface low-noise analog circuit industrial instrumentation portable electronics
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন