TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics
MPN: TS321ILT ✓ সক্রিয়TS321ILT সারাংশ
An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses external feedback to set its gain and filtering behavior. The TS321 belongs to the low-power operational-amplifier hierarchy, combining common-mode input range, open-loop gain, output-drive capability, and stability in a small integrated circuit. Its bipolar implementation is intended for cost-sensitive applications where the SOT-23-5 package can save board space compared with larger SOIC implementations.
The TS321ILT provides an 800 kHz gain-bandwidth product and 0.4 V/µs slew rate, making it appropriate for low-frequency audio, sensor conditioning, current monitoring, and general signal-shaping circuits. Its single-amplifier configuration reduces component count in applications that do not require a dual or quad amplifier. The 3 V to 30 V supply range also permits operation from conventional 5 V, 12 V, and 24 V industrial rails when the signal levels and dissipation permit.
STMicroelectronics describes the TS321 as a bipolar low-power operational amplifier intended for space-constrained, cost-sensitive designs. The device is specified to match or improve relevant performance characteristics of established industry-standard amplifiers such as LM358A and LM324 families. Because it is a single amplifier, systems requiring several independent signal channels must use multiple TS321ILT devices rather than one dual or quad package.
Typical uses include low-level sensor amplification, industrial control signal conditioning, audio preamplification, battery-powered instrumentation, and general analog buffers. In a practical inverting amplifier, the closed-loop bandwidth is determined by the feedback network as well as the 800 kHz gain-bandwidth product. Stable resistor and capacitor values should be selected with operating frequency, output swing, capacitive loading, and supply voltage taken into account.
The main design consideration is to avoid treating the approximate output-swing limits as full rail-to-rail operation. Input and output signals must remain inside the specified common-mode and output ranges. Designers should also check the stability behavior of the chosen feedback topology under expected source capacitance and load capacitance because those board-level conditions influence practical amplifier performance.
This product page combines the TS321ILT electrical specifications, package information, application guidance, and same-footprint replacement comparisons. It also provides practical guidance on feedback design, common-mode limits, supply selection, and PCB implementation so engineers can assess the amplifier before placing it in a new analog circuit.
এর জন্য ড্রপ-ইন বিকল্প TS321ILT — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible TS321ILT (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Number of Channels.
TS321IDT
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TS321AILT
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TS321AIDT
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TLV9301DBVR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TLV9301IDBVR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TS321ILT সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 800 kHz |
| Slew Rate | 0.4 V/µs |
| Supply Voltage Range | 3 V to 30 V |
| আউটপুট ভোল্টেজ রেঞ্জ | -1.5 V to +1.5 V |
| Architecture | Bipolar |
| Application Category | General-purpose amplifier |
| প্যাকেজ | SOT-23-5 |
| মাউন্টিং টাইপ | Surface mount |
TS321ILT sot-23-5 পিন কনফিগারেশন গাইড
TS321ILT (sot-23-5 প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি TS321ILT.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
TS321ILT এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Audio Preamplification, Battery-Powered Instrumentation, Current Monitoring and Control, Data Acquisition Front End, General-Purpose Buffering.
Industrial Sensor Signal Conditioning
The TS321ILT is suitable for conditioning low-level sensor signals in compact industrial control modules. Its 800 kHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensing interfaces, while the 0.4 V/µs slew rate supports moderate-amplitude dynamic signals. The single SOT-23-5 amplifier can be placed near the sensor connector to limit trace exposure to interference. Designers should bias the input within the common-mode range, verify output swing at the selected 5 V or 24 V supply, and check the closed-loop gain against the 800 kHz gain-bandwidth limit.
সুপারিশকৃত
Audio Preamplification
The TS321ILT can provide low-frequency audio preamplification in compact microphones, headphone accessories, and active speaker modules. Its 800 kHz gain-bandwidth product is suitable for audio bands below that limit when the closed-loop noise gain and required gain are considered, and the 0.4 V/µs slew rate reduces distortion risk for moderate output amplitudes. Place the amplifier close to the source and use short, shielded input routing to minimize electromagnetic pickup. The output must remain inside the specified approximately -1.5 V to +1.5 V range, so a higher supply or additional output stage may be needed for larger excursions.
সুপারিশকৃত
Battery-Powered Instrumentation
The TS321ILT fits low-power measurement blocks that amplify sensor outputs before conversion or switching. Its low-power single-amplifier architecture reduces the number of active devices needed for one analog channel, and the 3 V minimum supply supports compact energy-harvesting and portable systems. The amplifier's 800 kHz gain-bandwidth product is ample for many temperature, light, and slow-motion measurements, but offset, input bias current, and noise determine whether it is adequate for very small signals. Verify the complete current budget, use a low-noise reference, and keep the feedback network values consistent with the intended closed-loop response.
সুপারিশকৃত
Current Monitoring and Control
The TS321ILT can amplify the voltage produced by a shunt, sensor element, or feedback divider in a current-control loop. Its 800 kHz gain-bandwidth product and 0.4 V/µs slew rate are useful for low-to-medium-bandwidth regulation and monitoring, while the SOT-23-5 package helps minimize board area. The loop must account for amplifier phase margin and the delay introduced by feedback wiring. Place the amplifier near the shunt where practical, maintain a compact feedback loop, and verify that command signals remain within the output-swing limits rather than assuming rail-to-rail operation.
সুপারিশকৃত
Data Acquisition Front End
The TS321ILT is appropriate for the first gain stage of a compact data-acquisition front end when the sampled bandwidth is below its 800 kHz gain-bandwidth capability. A single amplifier can buffer or scale a sensor output before an ADC, reducing connector count and board area. Input filtering and gain selection should be coordinated so that noise, settling time, and capacitive loading meet the acquisition timing. The non-rail-to-rail output and input ranges must be mapped against the ADC input range, and the design should be checked for aliasing before the signal reaches higher-bandwidth conversion stages.
সুপারিশকৃত
General-Purpose Buffering
The TS321ILT can act as a voltage buffer when higher input impedance or isolation between source and load is required. Its 800 kHz bandwidth is suitable for many low-frequency control and measurement paths, and the compact SOT-23-5 footprint allows placement near sensitive circuitry. A unity-gain buffer still requires adequate output-current capability and stable operation with the intended source and load impedances. Add a small isolation resistor at the amplifier output when driving capacitive loads, and verify settling behavior if the buffered signal feeds a sampling or switching network.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TS321ILT — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
Consider the TLV9301DBVR or TLV9301IDBVR when a 1 MHz gain-bandwidth product and stated 40 V maximum supply rating are useful, but review input range, output swing, offset, noise, stability, and lifecycle details before replacing the TS321ILT. Neither a similar package nor similar low-power positioning proves functional interchangeability. For production, verify the exact ordering code, operating-temperature range, qualification status, RoHS documentation, and package tolerances against the manufacturer datasheet.
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TS321IDT | TS321AILT | TS321AIDT | TLV9301DBVR | TLV9301IDBVR |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same |
| Amplifier Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Primary Application | Low-power general-purpose amplification | Low-power general-purpose amplification | General-purpose amplification | General-purpose amplification | Low-power operational amplification | Low-power operational amplification |
মূল পার্থক্যসমূহ
- Lower slew rate supports a defined, modest-bandwidth signal path (বনামTLV9301DBVR)
- Direct match to the documented TS321 operating envelope (বনামTS321IDT)
- Lower maximum supply rating suits lower-voltage designs (বনামTLV9301IDBVR)
ডিজাইন নোট
Do not treat the TS321ILT as a rail-to-rail input or output amplifier. Its documented output range is approximately -1.5 V to +1.5 V, so the feedback network must keep command and signal voltages inside the specified common-mode range. For a 3 V supply, the available output span is especially constrained. Review the input and output characteristic curves in the STMicroelectronics TS321 datasheet before setting bias points or designing a 0 V-centered signal path.
Place the TS321ILT close to the feedback resistors, input source, and decoupling capacitor so that the high-gain feedback loop encloses as little PCB area as possible. Connect the supply and ground pins directly to the nearest capacitor. Keep sensitive input traces away from switching nodes and high-current paths. If the output drives a capacitive load, add a small isolation resistor near the amplifier and verify stability because external load capacitance can alter the closed-loop response.
Select feedback values so that the required closed-loop gain remains compatible with the 800 kHz gain-bandwidth product and the 0.4 V/µs slew rate. A practical rule is that the closed-loop bandwidth should remain below the amplifier's gain-bandwidth product with additional margin for the actual noise gain. For sinusoidal signals, confirm that the required peak amplitude can be reached within the output-swing range. Slow large-signal outputs can clip even when small-signal bandwidth calculations appear acceptable.
Check dissipation against the highest operating supply and expected output voltage rather than using the 5 V supply as a universal condition. Estimated: amplifier dissipation is approximately equal to supply current multiplied by the voltage dropped across the device. The datasheet supply-current limits and actual operating point must be used for the final thermal assessment, especially in a compact SOT-23-5 board where copper area may be limited.
কমপ্লায়েন্স তথ্য
No definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration for the exact TS321ILT ordering code was identified. Request the applicable STMicroelectronics compliance documents before regulated production use.