TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics
MPN: TS321ILT ✓ Hoạt độngTS321ILT Tóm tắt
An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses external feedback to set its gain and filtering behavior. The TS321 belongs to the low-power operational-amplifier hierarchy, combining common-mode input range, open-loop gain, output-drive capability, and stability in a small integrated circuit. Its bipolar implementation is intended for cost-sensitive applications where the SOT-23-5 package can save board space compared with larger SOIC implementations.
The TS321ILT provides an 800 kHz gain-bandwidth product and 0.4 V/µs slew rate, making it appropriate for low-frequency audio, sensor conditioning, current monitoring, and general signal-shaping circuits. Its single-amplifier configuration reduces component count in applications that do not require a dual or quad amplifier. The 3 V to 30 V supply range also permits operation from conventional 5 V, 12 V, and 24 V industrial rails when the signal levels and dissipation permit.
STMicroelectronics describes the TS321 as a bipolar low-power operational amplifier intended for space-constrained, cost-sensitive designs. The device is specified to match or improve relevant performance characteristics of established industry-standard amplifiers such as LM358A and LM324 families. Because it is a single amplifier, systems requiring several independent signal channels must use multiple TS321ILT devices rather than one dual or quad package.
Typical uses include low-level sensor amplification, industrial control signal conditioning, audio preamplification, battery-powered instrumentation, and general analog buffers. In a practical inverting amplifier, the closed-loop bandwidth is determined by the feedback network as well as the 800 kHz gain-bandwidth product. Stable resistor and capacitor values should be selected with operating frequency, output swing, capacitive loading, and supply voltage taken into account.
The main design consideration is to avoid treating the approximate output-swing limits as full rail-to-rail operation. Input and output signals must remain inside the specified common-mode and output ranges. Designers should also check the stability behavior of the chosen feedback topology under expected source capacitance and load capacitance because those board-level conditions influence practical amplifier performance.
This product page combines the TS321ILT electrical specifications, package information, application guidance, and same-footprint replacement comparisons. It also provides practical guidance on feedback design, common-mode limits, supply selection, and PCB implementation so engineers can assess the amplifier before placing it in a new analog circuit.
Bộ thay thế dễ dàng lắp đặt cho TS321ILT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS321ILT (cùng hình factor và footprint) — khác nhau ở Package, Number of Channels.
TS321IDT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TS321AILT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS321AIDT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9301DBVR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9301IDBVR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TS321ILT Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 800 kHz |
| Slew Rate | 0.4 V/µs |
| Supply Voltage Range | 3 V to 30 V |
| Khoảng điện áp đầu ra | -1.5 V to +1.5 V |
| Architecture | Bipolar |
| Application Category | General-purpose amplifier |
| Hộp | SOT-23-5 |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TS321ILT sot-23-5
Cấu hình chân cho TS321ILT (sot-23-5 gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS321ILT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS321ILT phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Audio Preamplification, Battery-Powered Instrumentation, Current Monitoring and Control, Data Acquisition Front End, General-Purpose Buffering.
Industrial Sensor Signal Conditioning
The TS321ILT is suitable for conditioning low-level sensor signals in compact industrial control modules. Its 800 kHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensing interfaces, while the 0.4 V/µs slew rate supports moderate-amplitude dynamic signals. The single SOT-23-5 amplifier can be placed near the sensor connector to limit trace exposure to interference. Designers should bias the input within the common-mode range, verify output swing at the selected 5 V or 24 V supply, and check the closed-loop gain against the 800 kHz gain-bandwidth limit.
Được đề xuất
Audio Preamplification
The TS321ILT can provide low-frequency audio preamplification in compact microphones, headphone accessories, and active speaker modules. Its 800 kHz gain-bandwidth product is suitable for audio bands below that limit when the closed-loop noise gain and required gain are considered, and the 0.4 V/µs slew rate reduces distortion risk for moderate output amplitudes. Place the amplifier close to the source and use short, shielded input routing to minimize electromagnetic pickup. The output must remain inside the specified approximately -1.5 V to +1.5 V range, so a higher supply or additional output stage may be needed for larger excursions.
Được đề xuất
Battery-Powered Instrumentation
The TS321ILT fits low-power measurement blocks that amplify sensor outputs before conversion or switching. Its low-power single-amplifier architecture reduces the number of active devices needed for one analog channel, and the 3 V minimum supply supports compact energy-harvesting and portable systems. The amplifier's 800 kHz gain-bandwidth product is ample for many temperature, light, and slow-motion measurements, but offset, input bias current, and noise determine whether it is adequate for very small signals. Verify the complete current budget, use a low-noise reference, and keep the feedback network values consistent with the intended closed-loop response.
Được đề xuất
Current Monitoring and Control
The TS321ILT can amplify the voltage produced by a shunt, sensor element, or feedback divider in a current-control loop. Its 800 kHz gain-bandwidth product and 0.4 V/µs slew rate are useful for low-to-medium-bandwidth regulation and monitoring, while the SOT-23-5 package helps minimize board area. The loop must account for amplifier phase margin and the delay introduced by feedback wiring. Place the amplifier near the shunt where practical, maintain a compact feedback loop, and verify that command signals remain within the output-swing limits rather than assuming rail-to-rail operation.
Được đề xuất
Data Acquisition Front End
The TS321ILT is appropriate for the first gain stage of a compact data-acquisition front end when the sampled bandwidth is below its 800 kHz gain-bandwidth capability. A single amplifier can buffer or scale a sensor output before an ADC, reducing connector count and board area. Input filtering and gain selection should be coordinated so that noise, settling time, and capacitive loading meet the acquisition timing. The non-rail-to-rail output and input ranges must be mapped against the ADC input range, and the design should be checked for aliasing before the signal reaches higher-bandwidth conversion stages.
Được đề xuất
General-Purpose Buffering
The TS321ILT can act as a voltage buffer when higher input impedance or isolation between source and load is required. Its 800 kHz bandwidth is suitable for many low-frequency control and measurement paths, and the compact SOT-23-5 footprint allows placement near sensitive circuitry. A unity-gain buffer still requires adequate output-current capability and stable operation with the intended source and load impedances. Add a small isolation resistor at the amplifier output when driving capacitive loads, and verify settling behavior if the buffered signal feeds a sampling or switching network.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS321ILT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Consider the TLV9301DBVR or TLV9301IDBVR when a 1 MHz gain-bandwidth product and stated 40 V maximum supply rating are useful, but review input range, output swing, offset, noise, stability, and lifecycle details before replacing the TS321ILT. Neither a similar package nor similar low-power positioning proves functional interchangeability. For production, verify the exact ordering code, operating-temperature range, qualification status, RoHS documentation, and package tolerances against the manufacturer datasheet.
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS321IDT | TS321AILT | TS321AIDT | TLV9301DBVR | TLV9301IDBVR |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same |
| Amplifier Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Primary Application | Low-power general-purpose amplification | Low-power general-purpose amplification | General-purpose amplification | General-purpose amplification | Low-power operational amplification | Low-power operational amplification |
Bảo phân biệt quan trọng
- Lower slew rate supports a defined, modest-bandwidth signal path (vsTLV9301DBVR)
- Direct match to the documented TS321 operating envelope (vsTS321IDT)
- Lower maximum supply rating suits lower-voltage designs (vsTLV9301IDBVR)
Ghi chú thiết kế
Do not treat the TS321ILT as a rail-to-rail input or output amplifier. Its documented output range is approximately -1.5 V to +1.5 V, so the feedback network must keep command and signal voltages inside the specified common-mode range. For a 3 V supply, the available output span is especially constrained. Review the input and output characteristic curves in the STMicroelectronics TS321 datasheet before setting bias points or designing a 0 V-centered signal path.
Place the TS321ILT close to the feedback resistors, input source, and decoupling capacitor so that the high-gain feedback loop encloses as little PCB area as possible. Connect the supply and ground pins directly to the nearest capacitor. Keep sensitive input traces away from switching nodes and high-current paths. If the output drives a capacitive load, add a small isolation resistor near the amplifier and verify stability because external load capacitance can alter the closed-loop response.
Select feedback values so that the required closed-loop gain remains compatible with the 800 kHz gain-bandwidth product and the 0.4 V/µs slew rate. A practical rule is that the closed-loop bandwidth should remain below the amplifier's gain-bandwidth product with additional margin for the actual noise gain. For sinusoidal signals, confirm that the required peak amplitude can be reached within the output-swing range. Slow large-signal outputs can clip even when small-signal bandwidth calculations appear acceptable.
Check dissipation against the highest operating supply and expected output voltage rather than using the 5 V supply as a universal condition. Estimated: amplifier dissipation is approximately equal to supply current multiplied by the voltage dropped across the device. The datasheet supply-current limits and actual operating point must be used for the final thermal assessment, especially in a compact SOT-23-5 board where copper area may be limited.
Thông tin tuân thủ
No definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration for the exact TS321ILT ordering code was identified. Request the applicable STMicroelectronics compliance documents before regulated production use.