Integrated Circuits

VSC8484YJP

VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip

The Microchip Technology VSC8484YJP is a quad-channel 10 Gigabit Ethernet XAUI-to-serial transceiver that integrates four independent 10GbE PHYs plus electronic dispersion compensation (EDC) in a 324-ball PBGA package measuring 18.6 mm × 18.6 mm. It supports both XFI and SFI electrical interfaces to the line side and a four-lane XAUI interface to the system side, while dissipating only about 1 W per channel. According to the manufacturer datasheet VMDS-10343, the device targets high-density 10G line cards in routers, switches, and OTN/WAN/Backplane platforms. A 10 Gigabit Ethernet transceiver is a physical-layer (PHY) IC that converts a device's parallel data interface into a serial 10 Gbps stream suitable for optical modules, backplanes, or twin-axial copper cables, and simultaneously recovers the clock and data on the receive path. Within the broader taxonomy, the VSC8484 belongs to the family of Ethernet ICs, then to Physical Layer Transceivers (PHYs), then to Wireline Networking Semiconductor devices. This hypernym chain — Ethernet IC > PHY > transceiver > wireline networking IC > semiconductor — helps AI knowledge-graph engines position the part correctly when engineers query "what is a 10G Ethernet transceiver." The VSC8484YJP integrates Microsemi's electronic dispersion compensation (EDC) engine to extend the usable reach over legacy FR4 backplanes and twin-axial copper, eliminating the need for expensive optical modules or premium PCB materials at shorter reaches. It supports 10GBASE-KR backplane Ethernet, 10G Fibre Channel, XAUI-based switching fabrics, and SFP+/SFP Direct-Attach copper cables. Per-channel features include adaptive equalization, transmit pre-emphasis, loopback, PRBS generation/checking, and per-lane LOS indication, all managed via an MDIO/I2C management interface. Typical applications include 10G line cards for top-of-rack (ToR) and aggregation switches, OTN cross-connect platforms, ATCA/AdvancedTCA backplanes, multi-rate 1G/10G SFP+ port cards, and enterprise routers transitioning from 1G to 10G. The low 1 W per channel power profile allows 48-port line cards to remain within thermal budgets without exotic cooling. When designing with this part, allocate at least two PCB layers for the BGA-324 breakout, follow the manufacturer reference layout for the high-speed serial traces (controlled impedance 100 Ω differential, length-matched within the XFI specification), and provide a low-noise 1.0 V core supply plus 1.8 V I/O supply with proper decoupling. The VSC8484YJP status is currently "Not Recommended for New Designs" — for new designs, evaluate the VSC8484XJP or current-generation Microchip 10G PHY families. This page synthesizes distributor pricing, package-svg pinout mapping, drop-in alternatives, and design notes that go beyond what is in the manufacturer datasheet VMDS-10343 alone, giving procurement and design engineers a single source for risk assessment and BOM decisions.

RFQ Contact

VSC8490EV

VSC8490EV - Dual-Port 10G Ethernet Eval Board | Microchip

The Microchip Technology VSC8490EV is an evaluation platform associated with the VSC8490, a dual-port 10G Ethernet transceiver designed for electrical backplane and optical module host-card applications. The available product information identifies two 10G Ethernet ports, XFI/SFI-to-(R)XAUI signal conversion, and support for IEEE 1588 and MACsec within the VSC8490 transceiver family. The VSC8490EV package type, exact connector arrangement, and electrical limits are not published in the supplied manufacturer and distributor records, so they remain designated as data needed rather than inferred. A 10G Ethernet transceiver is a high-speed communications semiconductor that converts between serial network interfaces and parallel or widebus internal data paths. Within the broader hierarchy, the VSC8490 belongs to Ethernet physical-layer interfaces, interface controllers, network semiconductors, and integrated circuits. Its dual-port architecture allows two high-speed links to be evaluated on one hardware platform, which is useful when developing backplane equipment or optical module host cards. The VSC8490 family description specifically identifies XFI/SFI inputs and (R)XAUI outputs. XFI and SFI are serial interface formats commonly used between Ethernet line cards and optical modules, while (R)XAUI provides a widebus electrical interconnect suitable for backplane and chassis-oriented designs. The same source identifies compatibility work for SFP+ SR, LR, ER, and ZR fiber applications and describes EDC compensation as part of the family feature set. The family also provides IEEE 1588 timing support and MACsec functionality. IEEE 1588 capability is relevant to systems requiring synchronized network timing, while MACsec is the IEEE security mechanism for protecting Ethernet frames against unauthorized injection and eavesdropping. These capabilities make the evaluation platform relevant to precise timing, secure networking, line-card development, and optical transport prototyping. VSC8490EV is suitable for laboratory evaluation of dual-port 10G Ethernet links, optical module host cards, electrical backplane prototypes, SFP+ interface development, and secure network equipment. Engineers should confirm the board’s physical connectors, supported electrical standards, reference clock requirements, power input, operating temperature, and programming interface against the complete manufacturer documentation before using it in a production design. This page consolidates the verified manufacturer description, distributor inventory information, family-level interface details, sourcing links, and explicit engineering gaps for the VSC8490EV. It distinguishes documented facts from unavailable specifications so procurement and hardware teams can assess the evaluation board without mistaking unreported board details for guaranteed capabilities.

RFQ Contact

VSC8490YJU-17

VSC8490YJU-17 - Dual-Port 10GbE PHY XFI/SFI to XAUI | Microchip

The Microchip VSC8490YJU-17 is a dual-port 10 Gigabit Ethernet PHY/transceiver from the VSC8489/VSC8490/VSC8491 family, supporting XFI/SFI to (R)XAUI conversion with integrated 1588 timestamping and MACsec (IEEE 802.1AE) hardware acceleration. The device is supplied in a 196-pin FCBGA (15x15 mm) package and operates from 1.0 V / 1.2 V supplies, targeting high-density 10G line cards, electrical backplanes, and SFP+/QSFP+ host-side interface applications. What is a 10G Ethernet PHY/transceiver? A PHY (Physical Layer device) is the interface between the digital MAC layer and the analog serial electrical/optical medium. Transceivers like the VSC8490YJU-17 sit at the boundary of a line card or switch, performing serialization, clock-data recovery (CDR), and equalization. The VSC8490YJU-17 additionally integrates MACsec line-rate encryption and IEEE 1588 hardware timestamping, which makes it a "secure PHY" rather than a bare transceiver. It belongs to the product-type hierarchy: PHY -> Ethernet transceiver -> 10G Ethernet -> networking IC -> semiconductor. Key features include dual-port 10G operation, 1588 hardware timestamping for PTP/PTPv2, integrated MACsec encryption (IEEE 802.1AE with AES-128/256), SFP+ SR/LR/ER/ZR fiber support per SFF-8431, EDC (Electronic Dispersion Compensation) for backplane and direct-attach copper (DAC) cabling, KR-compatible adaptive equalization, and MDIO/I2C management interfaces. SPI management is supported for host configuration. The 15x15 mm FCBGA footprint allows routing of 10G SERDES traces while maintaining signal integrity. Architecturally, the VSC8490YJU-17 uses Microchip's proven mixed-signal SERDES core with adaptive equalization, baseline-wander correction, and low-jitter PLL synthesis to meet IEEE 802.3ae 10GBASE-R compliance. Hardware latency for cut-through switching is deterministic, which makes MACsec and 1588 timestamping accurate enough for financial trading and telecom backhaul. Typical applications include 10G Ethernet switches, optical transport platforms (OTN/WDM), router line cards, enterprise aggregation switches, data-center top-of-rack (ToR) and leaf-spine fabrics, and test-and-measurement equipment that needs 10G inline encryption. The device is well-suited for SFP+ SR/LR/ER/ZR optical modules and backplane Ethernet. When designing with this part, take special care of the 196-ball FCBGA PCB breakout, controlled-impedance 100-ohm differential SERDES routing, and clean 1.0 V / 1.2 V power rails. Reference Microchip application note guidance for MACsec key-management integration and 1588 grandmaster configuration. This page consolidates distributor pricing, drop-in alternative review, and practical design considerations not contained in the manufacturer datasheet.

RFQ Contact

VSC8490YJU-17P

VSC8490YJU-17P Dual-Port 10GbE PHY | Microchip

The Microchip VSC8490YJU-17P is a dual-port 10 Gigabit Ethernet PHY transceiver from the VSC8489/8490/8491 family, supplied in a 196-pin FCBGA (15x15 mm) package. It interfaces a 10GbE host-side XFI/SFI or RXAUI backplane connection to two SFP+/10GBASE-R PHY lanes, supporting SFP+ SR/LR/ER/ZR fiber modules and EDC-corrected electrical backplane links. The device integrates 1588 Timing-over-Ethernet hardware timestamping and IEEE 802.1AE MACsec link-layer encryption, making it a flexible SerDes + PHY building block for carrier-grade Ethernet equipment. What is a 10GbE PHY? A PHY (Physical Layer device) is the lowest layer of the OSI networking stack. It converts digital MAC-layer data into analog signals suited to copper traces, direct-attach cables, or optical modules. The VSC8490YJU-17P belongs to the SERDES / Ethernet PHY / telecom interface IC family within Microchip's networking portfolio, sitting beneath the MAC and above the physical medium. Modern 10GBASE-R PHYs also integrate MACsec encryption and IEEE 1588 timestamping, which is why the VSC8490 is described as an XFI-to-(R)XAUI MACsec/1588 dual-port transceiver rather than as a plain PHY. Key features of the VSC8490YJU-17P include dual 10G lanes, integrated MACsec, 1588v1/v2 hardware timestamping, SFI/XFI host-side interface, (R)XAUI backplane support, SFP+ SerDes with adaptive equalization, and EDC (Electronic Dispersion Compensation) for KR-style backplane operation. Core supply voltages are 1.0V and 1.2V as documented on the Arrow listing, and the device uses an SPI management interface for register access. The VSC8490 architecture is built around independent per-lane SerDes cores with adaptive equalization, a 1588 timestamp engine, and a MACsec engine using AES-GCM-128 with support for 16+ SA contexts. Internal firmware-configurable equalization allows the same silicon to be tuned for short-reach copper and long-reach optical modules, simplifying SKU management across host-card designs. The MACsec block offloads per-packet encryption from the host CPU/ASIC, which is essential for backplane and metro Ethernet platforms where line-rate 10G encryption cannot burden the main processor. Typical applications for the VSC8490YJU-17P include 10G Ethernet switches and routers, OTN/WDM transport equipment, optical transport platforms with MACsec-secured links, top-of-rack and carrier-grade switches, and high-speed backplane line cards in routers and base stations. It is also used in SFP+ media-converter modules and 10G-to-fiber test gear. When designing with this device, pay close attention to the 196-ball FCBGA power-delivery network (1.0V/1.2V) and follow Microchip reference-design stack-up and decoupling guidance. Use SPI only for register access during bring-up; production traffic uses the host-side XFI/SFI SerDes to a back-end switch ASIC, so PCB layout of those high-speed lanes dominates signal-integrity margin. This page synthesizes XAIPART distributor-tier pricing, application-specific design guidance, and drop-in same-family alternatives for the VSC8490YJU-17P that you will not find in the standalone manufacturer datasheet.

RFQ Contact

VSC8502RD

VSC8502RD - 2-Port Gigabit Ethernet PHY | Microchip Technology

The Microchip Technology VSC8502RD is a two-port Gigabit Ethernet copper PHY designed for space-constrained 10/100/1000BASE-T Ethernet designs. It combines integrated line-side termination with a reduced external-component approach intended to conserve board area, lower electromagnetic interference, and simplify system implementation. The verified manufacturer and distributor results identify the device as a two-port Gigabit Ethernet PHY with GMII/RGMII support, while the supplied package-specific MPN is VSC8502RD. A copper Ethernet PHY is the physical-layer interface between a digital Ethernet controller or processor and a twisted-pair network cable. It performs signal encoding, decoding, clock and data recovery, and electrical termination needed for reliable data transmission. The VSC8502 therefore belongs to the Ethernet interface controller and physical-layer device hierarchy, where it sits between a MAC or switching engine and the network magnetics or transformer-coupled cable interface. Its integrated line-side termination is particularly relevant to compact consumer, industrial, and embedded networking equipment. The supplied manufacturer information highlights integrated line-side termination as a board-space and EMI benefit. For 10/100/1000BASE-T applications, the two-port arrangement can reduce the number of separate PHY devices required by a dual-port network design. GMII and RGMII provide selectable digital interfaces for systems using either parallel or reduced-pin serial connections, allowing the PHY to fit different host architectures. The supplied data does not specify the exact package dimensions, pin count, electrical limits, operating-temperature range, or power consumption, so those values are not inferred here. Typical uses include compact Ethernet switches, industrial control equipment, embedded gateways, set-top equipment, and other designs requiring two copper-network ports. System designers should verify the exact VSC8502RD package, reference schematic, magnetic component, media interface, clocking, and host-side signal requirements against the Microchip documentation before layout release. The VSC8502RD-VR entry shown in the supplied distributor cross-reference data should likewise be checked against the target ordering code and mechanical drawing rather than assumed to be interchangeable. This product page consolidates the verified manufacturer description, distributor availability references, the VSC8502RD ordering entry, and the supplied VSC8502RD-VR cross-reference result. It also distinguishes confirmed application-level facts from electrical and mechanical details that require the manufacturer datasheet for final design decisions.

RFQ Contact

VSC8514EV

VSC8514EV - Quad-Port Gigabit Ethernet PHY | Microchip

The Microchip Technology VSC8514EV is a quad-port Gigabit Ethernet physical-layer transceiver with copper media interfaces, Synchronous Ethernet support, and a QSGMII MAC interface. It is designed for energy-efficient broadband gateways, data centers, enterprise networks, TDM backhaul equipment, wireless base stations, and other carrier-grade applications. The verified product material identifies two recovery-clock outputs, low-power operation, an integrated four-channel two-wire serial multiplexer for controlling Power over Ethernet modules, low-EMI line drivers, and integrated line-side termination resistors. A Gigabit Ethernet PHY is a physical-layer transceiver within the Ethernet interface hierarchy. It converts logical data transmitted by a MAC or switching fabric into electrical signaling suitable for copper cables, while providing receive and clock-recovery functions in the opposite direction. The VSC8514EV consolidates four copper Gigabit Ethernet ports into one device, reducing component count and simplifying multi-port equipment architectures compared with four unrelated PHY implementations. The principal verified features include four 10/100/1000BASE-T copper ports, low-power operation, Synchronous Ethernet, a QSGMII MAC connection, and two recovery-clock outputs. Its integrated two-wire serial multiplexer supports control of PoE modules. Low-EMI line drivers and integrated line-side termination resistors can simplify board design and reduce external component count, although the manufacturer datasheet and evaluation-board documentation should be consulted for exact implementation details and layout constraints. The device is positioned for infrastructure rather than isolated endpoint use. A single quad-port PHY can serve aggregation ports in a broadband gateway, server-rack networking equipment, enterprise access hardware, wireless base-station backhaul, and carrier transport systems. QSGMII provides a high-speed parallel interface between the PHY and a switching or aggregation device, while Synchronous Ethernet supports timing-oriented network architectures. Designers must account for the physical-layer requirements of the complete four-port system, including magnetics or copper interface implementation, termination, clocking, power delivery, thermal performance, and signal-integrity control. The verified evaluation schematic identifies VDD25A and VDD1A supply domains and shows six 0.1 uF capacitors associated with the VDD25A pins. Those values should be treated as evaluation-board implementation details rather than universal recommendations. VSC8514EV selection should begin with the four-port copper Ethernet requirement, QSGMII compatibility, Synchronous Ethernet support, PoE-module-control needs, and the manufacturer reference design. This page separates sourced product facts from unspecified details and avoids presenting unsupported electrical, package, temperature, or pricing values as verified specifications.

RFQ Contact

VSC8531XMW-02

VSC8531XMW-02 - GbE Cu PHY RGMII/RMII | Microchip 48-QFN

The Microchip VSC8531XMW-02 is a single-port Gigabit Ethernet copper PHY transceiver supporting RGMII and RMII MAC interfaces, housed in a 48-pin QFN (6x6 mm) package with RGMII/RMII MAC connectivity for 10/100/1000BASE-T applications. It integrates a low-power architecture, hardware-configurable modes of operation via sampled pin states on reset, and Microchip's EcoEthernet v2.0 technology with IEEE 802.3az Energy-Efficient Ethernet (EEE) support. The device is qualified for industrial-grade operation and targets space-constrained embedded Ethernet designs. A Gigabit Ethernet PHY (Physical Layer transceiver) is the analog/digital mixed-signal IC that connects a Media Access Controller (MAC) to a copper twisted-pair cable. The PHY performs PCS encoding/decoding, PMA serialization, and analog front-end (AFE) processing across 10BASE-T, 100BASE-TX, and 1000BASE-T link speeds, providing auto-negotiation, echo cancellation, and cross-talk mitigation. Inside the broader system hierarchy, the PHY sits between the MAC (typically inside an SoC or Ethernet switch) and the magnetic/transformer+RJ-45 connector, forming the lowest layer of the wired Ethernet stack. Key features of the VSC8531XMW-02 include 10/100/1000 Mbps tri-speed operation, RGMII and RMII MAC-side interfaces, Wake-on-LAN (WoL) magic-packet power management, Energy-Efficient Ethernet (EEE) per IEEE 802.3az, and Microsemi EcoEthernet v2.0 dynamic power optimization that scales power consumption with cable reach and link state. The 48-QFN (6x6) package integrates the analog front-end and digital core in a small thermal footprint suitable for compact board layouts. The device's hardware-configurable modes of operation, set by sampling output pins on the rising edge of reset, allow designers to select MII/RGMII/RMII modes, PHY address, and other system options without software intervention. Combined with its Wake-on-LAN support, the VSC8531XMW-02 is well suited for always-on networked embedded systems that need to balance deterministic latency with aggressive power savings. Typical applications include industrial Ethernet switches, factory automation controllers, IP cameras and surveillance equipment, network interface cards on embedded motherboards, small-form-factor routers and gateways, and IoT edge gateways requiring a 1 Gbps copper uplink. Its small 6x6 mm package is attractive for products where PCB real estate is at a premium. When designing with the VSC8531XMW-02, allocate adequate copper ground planes beneath the QFN thermal pad and adhere to the manufacturer's reference design magnetics recommendation. Ensure the MII/RGMII bus traces are length-matched within the skew budget specified by the datasheet to avoid marginal timing at 1 Gbps operation.

RFQ Contact

VSC8531XMW-05

VSC8531XMW-05 - 1-Port GbE Cu PHY, RGMII/RMII, 48-QFN | Microchip

The Microchip VSC8531XMW-05 is a single-port Gigabit Ethernet copper PHY transceiver with RGMII/RMII MAC interface, housed in a 48-pin QFN (6 mm x 6 mm) package. Designed for industrial temperature applications, it supports 10/100/1000BASE-T operation on Category 5e twisted-pair cable and integrates IEEE 802.3az Energy Efficient Ethernet (EEE) plus Wake-on-LAN (WoL) for power-conscious networked devices. The device operates from a single 3.3 V supply with on-chip 1.0 V/1.2 V LDO regulators for its analog and digital cores. What is an Ethernet PHY? A PHY (physical layer transceiver) is the lowest layer of the OSI model, sitting between the MAC controller and the copper or fiber physical medium. Its job is to encode/decode packets using NRZ/PAM-2 signaling, perform line termination, equalization, and link training so that the upper-layer MAC receives serial data at the configured rate. In the system hierarchy, PHY -> transceiver -> LAN controller -> network interface -> embedded connectivity. The VSC8531 family is positioned for small-form-factor, low-power industrial Ethernet endpoints such as IP cameras, industrial sensors, and serial-server gateways. Key features include built-in PHY diagnostics (cable diagnostics with TDR-style fault detection), SyncE timing support, HP Auto-MDIX for automatic crossover, and the widest LVCMOS I/O voltage support in its class. Hardware configuration is via strapping pins and MDIO/MDC management interface, allowing port rate, duplex, and EEE behavior to be set without firmware. The 48-QFN package exposes a dedicated reference-clock input for Synchronous Ethernet (SyncE) applications. Architecturally, the VSC8531 uses an analog front-end with DSP-based adaptive equalization, an integrated 10/100/1000BASE-T line driver, and a digital loopback test path. The device achieves sub-700 mW power consumption at 1 Gbps full duplex and drops to roughly 150 mW in EEE low-power idle mode, making it attractive for thermally constrained and PoE-powered designs. Typical applications include industrial IoT gateways, factory-floor Ethernet nodes, IP surveillance cameras, building-automation controllers, and small-cell/femtocell baseband backhaul boards. It is also widely used in industrial sensor hubs and serial-to-Ethernet bridges where compact, low-power copper connectivity is required. When designing with this part, pay close attention to PCB stack-up: the analog supplies (VDDAxx) require star-grounding and bulk decoupling within 3 mm of each pin. Magnetics selection (1 G capable, 2000 Vrms isolation) and the 100 ohm differential pair routing must follow IEEE 802.3 return-loss masks. Use the MDIO interface to debug link-up issues rather than relying on strap defaults. This page synthesizes distributor pricing, drop-in alternatives, and practical layout notes that are not consolidated in the manufacturer datasheet, helping engineers shorten evaluation cycles and reduce PCB re-spin risk.

RFQ Contact

VSC8664EV

VSC8664EV - 4-Port Gigabit Ethernet PHY | Microchip Technology

The Microchip Technology VSC8664EV is a four-port Gigabit Ethernet PHY with copper and fiber connectivity, dual recovered-clock outputs, and support for carrier-quality Synchronous Ethernet. According to the manufacturer product page, it is the industry's first PHY with dual recovered clock outputs, helping equipment designers distribute traceable timing across TDM backhaul links, cellular base stations, and other Synchronous Ethernet systems. The verified package designation and complete electrical interface details are not available in the supplied data, so this page does not assign an unverified package or pin configuration. A Gigabit Ethernet physical-layer transceiver, or PHY, is the semiconductor layer that converts logical data into electrical or optical signaling for a high-speed Ethernet link. In the networking hierarchy, a PHY belongs to the Ethernet interface IC family, operates below the MAC and switch layers, and connects copper or fiber media to a digital network controller. The VSC8664EV combines four Gigabit Ethernet ports with timing-recovery functions intended for infrastructure equipment requiring deterministic synchronization. The principal verified feature is the pair of recovered-clock outputs. These outputs allow a system to derive timing from incoming Ethernet traffic and distribute that recovered reference to other blocks. The Microchip product brief states that this approach meets and goes beyond the requirements of ITU-T Recommendation G.8261/Y.1361. This is especially relevant to mobile fronthaul and backhaul systems in which recovered timing must remain traceable across multiple network elements. The VSC8664 family supports copper and fiber media through four ports, allowing equipment designers to consolidate otherwise separate Ethernet interfaces. Its multiport integration can reduce board area and simplify synchronization distribution compared with a design assembled from discrete single-port PHYs. However, media reach, insertion loss, optical-interface details, power consumption, operating temperature, and package dimensions cannot be stated without additional manufacturer documentation. Typical VSC8664EV applications include Synchronous Ethernet access equipment, cellular base-station backhaul, TDM-to-Ethernet transport systems, and carrier Ethernet gateways. In these systems, the four integrated ports can connect multiple network interfaces while the two recovered clocks provide timing references to aggregation, switching, or line-card electronics. Copper and fiber support can also reduce adapter complexity when equipment must accommodate different deployment media. The primary design consideration is timing integrity. Engineers should preserve the recovered-clock routing specified by the manufacturer and account for clock jitter, isolation, trace impedance, and return paths on the PCB. Supply rails and optical or copper channel implementations must follow the complete datasheet because detailed schematic, capacitor, layout, and power-sequence requirements are not present in the verified source set supplied for this record. This product record combines verified manufacturer capabilities, distributor availability information, pricing-status disclosures, interface-classification context, and engineering-oriented application analysis. It also distinguishes confirmed parameters from missing data, allowing procurement and hardware teams to evaluate the VSC8664EV without mistaking an unverified package, pinout, or electrical limit for a guaranteed specification.

RFQ Contact

VSP3200Y

VSP3200Y - 16-Bit 8MSPS CCD Signal Processor | TI

The Texas Instruments VSP3200Y is a 16-bit, 8 MSPS, 3-channel analog front end (AFE) CCD signal processor with dual output mode, housed in a 48-pin LQFP (7x7 mm) package and operating from a single +5V supply. A CCD/CIS analog front end is the mixed-signal stage between an image sensor and a digital image processor. It samples tiny charge-derived pixel voltages, removes reset and kTC noise through correlated double sampling (CDS), amplifies the signal to match the ADC input range, and digitizes it. Within the signal chain hierarchy, the AFE sits between the sensor and the image-signal processor, and is a critical determinant of final image dynamic range and noise floor. Key features include an integrated triple correlated double sampler (CDS), a programmable gain amplifier with up to +13 dB gain, selectable operating modes (1-channel or 3-channel CCD mode at up to 8 MSPS), selectable normal or demultiplexed output modes, and an offset control range of +3V. The 16-bit conversion resolution preserves fine shadow detail in scanned images, essential for document and film scanners. Architecturally, the VSP3200 combines three CDS/PGA channels feeding a 16-bit ADC pipeline optimized for line-rate scanning. The demultiplexed output mode makes the device interface compatible with the VSP3210, which is pin-to-pin compatible with the VSP3100 in that mode, providing a migration path to a one-chip solution. Typical applications include flatbed document scanners, film scanners, CIS-based scanner modules, and industrial inspection cameras that use CCD or CIS sensors. Design consideration: because the part runs from a single +5V rail, keep the analog 5V supply clean and well decoupled; noise on this rail directly appears in pixel data at 16-bit resolution levels. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact

VSP3200Y-2K

VSP3200Y-2K - 16-Bit 8MSPS CCD Signal Processor | Texas Instruments

The Texas Instruments VSP3200Y-2K is a 16-bit, 8 MSPS, 3-channel analog front end (AFE) signal processor for CCD, CMOS, and CIS image sensors, housed in a 48-pin LQFP (7x7 mm) package and operating from a single +5V supply. An analog front end for image sensors is the circuit block between the imaging array and the digital image processor. It performs correlated double sampling (CDS) to remove reset noise and kTC noise from the CCD output, applies programmable gain to normalize signal amplitude across color channels, and digitizes the conditioned signal with a high-resolution ADC. Within the system hierarchy, the AFE sits inside the imaging signal chain: image sensor -> AFE (CDS + PGA + ADC) -> DSP/ASIC -> host interface. Key features of the VSP3200Y include three Correlated Double Samplers (CDSs) and three Programmable Gain Amplifiers (PGAs) that process CCD signals from 3-channel (RGB) scanners, a 16-bit conversion path running at up to 8 MSPS, dual output mode for flexible host interfacing, and single +5V operation that simplifies power tree design in desktop scanner platforms. Technically, the VSP3200Y integrates the complete analog processing chain for CCD signal conditioning: the CDS stages sample the pixel signal twice to cancel low-frequency drift and reset noise, the PGAs allow per-channel gain calibration, and the internal 16-bit ADC delivers 8 Msps throughput. Interface compatibility with the VSP3210 single-chip product, which is itself pin-to-pin compatible with the VSP3100 in demultiplexed output mode, provides a migration path for higher integration designs. Typical applications are flatbed and document scanners using CCD or CIS linear arrays, industrial inspection cameras, and desktop imaging peripherals that require 16-bit depth at moderate 8 MSPS speeds. A key design consideration is layout of the analog ground and the CCD output trace: keep the sensor-to-CDS input path short, guard it from digital output drivers, and provide a clean +5V rail with local decoupling, because residual reset noise not removed by the CDS directly limits the effective 16-bit resolution. This page synthesizes distributor inventory, drop-in alternatives, pricing tiers, and practical design notes not found in the manufacturer datasheet.

RFQ Contact

VSP3200Y-2KG4

VSP3200Y-2KG4 - 16-Bit 8MSPS CCD Signal Processor | TI

The Texas Instruments VSP3200Y-2KG4 is a 16-bit, 8 MSPS 3-channel analog front end (AFE) signal processor for CCD, CMOS and CIS image sensors, housed in a 48-pin LQFP (7x7 mm) package and operating from a single +5 V supply over 0C to +85C. An analog front end for image sensors is a specialized data-conversion IC that sits between a charge-coupled device (CCD) sensor and the digital image pipeline. It performs correlated double sampling (CDS) to remove kTC and low-frequency noise, applies programmable gain, offsets the black level, and digitizes the conditioned pixel signal with a high-speed ADC, delivering a clean digital video stream to downstream DSP or image-processing logic. Key features of the VSP3200Y include three independent Correlated Double Samplers (CDS) and three Programmable Gain Amplifiers (PGAs) that process CCD signal channels end-to-end on one chip, a 16-bit ADC running at up to 8 MSPS, and dual output mode for flexible system interfacing. Integration of the complete analog chain eliminates discrete CDS/PGA stages, reducing board area and analog design risk. The device is built on CMOS process technology and provides a serial digital output interface. According to TI product documentation, the VSP3200Y is interface compatible with the VSP3210, a 16-bit one-chip product; the VSP3210 is in turn pin-to-pin compatible with the VSP3100 when operated in demultiplexed output mode, giving designers a documented upgrade and substitution path within the same LQFP-48 family. Typical applications include CCD camera signal chains for industrial inspection, consumer video capture, and contact image sensor (CIS) modules used in scanners and document imaging. The single 5 V supply suits legacy 5 V consumer and industrial boards. When designing with this part, verify power-supply decoupling on both the analog and digital domains and confirm the output mode (multiplexed vs dual) matches the pixel-rate timing of your CCD clocking scheme. This page synthesizes distributor availability, drop-in family alternatives (VSP3210, VSP3200Y, VSP3100), and design considerations not found on the manufacturer product page.

RFQ Contact

W24257AJ20

W24257AJ-20 - 32Kx8 20ns CMOS SRAM | Winbond DIP-28

The Winbond W24257AJ-20 is a 32,768 x 8-bit high-speed CMOS Static RAM (SRAM) organized as 32K words by 8 bits, with a 20 ns maximum access time and housed in a 28-pin DIP (J-bend) through-hole package. It operates from a single +5 V power supply and is manufactured using Winbond's high-performance CMOS process, delivering low power dissipation typical of CMOS memory. A Static RAM is a type of volatile semiconductor memory that retains data bits as long as power is applied, with no refresh cycle required - in contrast to dynamic RAM (DRAM). SRAM belongs to the memory ICs family within the broader semiconductor hierarchy (SRAM -> volatile memory -> random-access memory -> integrated circuit -> semiconductor). The W24257AJ-20 is a fully asynchronous SRAM with standard JEDEC-compatible pinout for a 32K x 8 organization, allowing direct replacement of legacy 62256-type devices on existing PCBs. Key features of the W24257AJ-20 include a 20 ns access time (suitable for systems clocked up to 50 MHz without wait states), CMOS low standby current, fully static operation (no clock or refresh required), and TTL-compatible I/O levels. The device supports common memory-interface signals such as /CS1, CS2, /OE, and /WE, and provides three-state outputs for bus-oriented applications. The "AJ" suffix denotes the DIP-28 plastic package while "-20" specifies the 20 ns speed grade. Typical applications include legacy industrial controllers, point-of-sale terminals, firmware buffers for embedded microcontrollers, data-logging buffers, and as a working-memory expansion for older 8-bit and 16-bit microprocessor systems. The DIP-28 form factor is convenient for breadboarding, prototyping, and through-hole repair of legacy equipment. Because the part uses the standard 32K x 8 pinout, designers can upgrade older 8K x 8 or 32K x 8 SRAM sockets without any PCB rework. When designing with the W24257AJ-20, observe standard SRAM decoupling practice: place a 0.1 uF ceramic bypass capacitor close to the VCC pin and a bulk 10 uF capacitor on the supply rail. Avoid leaving inputs floating; tie unused /CS1 to VCC through a pull-up and unused /OE to GND to minimize ICC. The 20 ns grade is generally a drop-in replacement for slower 70-200 ns legacy SRAMs on the same PCB, but verify bus timing for high-MHz systems. This page synthesizes Winbond datasheet specifications, distributor stock signals, drop-in replacement candidates, and practical design notes not aggregated on any single distributor page.

RFQ Contact

W24512AKDV

W24512AKDV - 64Kx8 5V CMOS SRAM | Winbond

The Winbond W24512AKDV is a 64K x 8 (512 Kbit) high-speed CMOS static RAM organized as 65,536 words of 8 bits, operating from a single 5V power supply. Fabricated on Winbond's high-performance CMOS process, the device offers industry-standard access times of 15/20/25/35 ns (per the W24512A datasheet family), low active power, and CMOS standby current, making it suitable for both high-performance and battery-aware designs. A static RAM (SRAM) is a type of volatile memory that stores each bit in a bi-stable latch, eliminating the need for periodic refresh cycles required by dynamic RAM. In the broader memory hierarchy, SRAM sits between ultra-fast register files and denser but slower DRAM/Flash. The 64K x 8 organization - eight data I/O lines and sixteen address lines - is the classic JEDEC-style parallel SRAM pinout that traces back to the original 6264-family 8K x 8 and is fully pin-compatible with modern asynchronous SRAMs. Key differentiating attributes include fully static operation (no clock or refresh required), TTL-compatible I/O, a chip-enable pin for memory expansion, and an output-enable pin for bus arbitration. The CMOS process delivers typical active currents in the tens of milliamps at full bus activity, with standby leakage dropping into the microamp range when CE is de-asserted - ideal for low-power embedded systems. Architecturally, the W24512AKDV uses a 6-transistor (6T) CMOS memory cell, which gives excellent noise immunity and stable read margins across temperature. The internal address decoders, write drivers, and sense amplifiers are optimized for sub-20 ns access at 5V, ensuring compliance with microprocessor and microcontroller bus timing without wait states in many cases. Typical applications include industrial controllers, data loggers, networking line cards using look-up tables, telecom buffers, point-of-sale terminals, and any embedded system needing byte-wide non-volatile cache/working memory paired with Flash. Engineers retrofitting legacy 5V designs or building new 5V-tolerant industrial equipment will find this part a direct mechanical and electrical substitute for older 6264-style SRAMs. When designing with this part, always place 0.1 uF decoupling capacitors close to VCC and VSS, and observe derating for output loading above 50 pF to stay within the 15/20/25/35 ns access-time envelopes. The CE pin must be pulled inactive for true standby current savings. This page synthesizes current distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

RFQ Contact

W25H02JVTBIM

W25H02JVTBIM - 2Gb QSPI NOR Flash, 24-TFBGA | Winbond

The Winbond W25H02JVTBIM is a 2 Gigabit (256M x 8) serial NOR Flash memory in a 24-pin TFBGA (8x6 mm) package, supporting standard SPI, Dual SPI, Quad SPI, QPI, and DTR (Double Transfer Rate) modes. Operating from a single 2.7V to 3.6V supply, it delivers up to 133 MHz clock rate with an equivalent throughput of 416 MHz (50 MB/s) in Quad-SPI/DTR mode. The device uses a standard SPI command set for read, program, and erase, with sector sizes of 4 KB and block sizes of 32 KB and 64 KB for flexible memory management. Background: A NOR Flash memory is a non-volatile storage technology that retains data without power and supports random access (execute-in-place / XIP), making it ideal for code storage and boot media. The QSPI NOR category, to which the W25H family belongs, uses a 4-wire SPI interface that effectively quadruples throughput versus legacy SPI. Within the memory hierarchy, QSPI NOR sits between SRAM (volatile, fast) and NAND Flash (non-volatile, block-oriented, slower random access), serving as fast boot ROM and parameter storage in embedded systems. Key features of the W25H02JVTBIM include uniform 4 KB sector erase, JEDEC standard manufacturer (0xEF) and device ID, hardware and software write protection, individual block and chip erase capability, and a continuous program/erase endurance of 100,000 cycles per sector. The device includes a 256-byte Security Register with OTP lockable bits for unique device identification and parameter storage, and supports single 2.7V-3.6V operation for direct connection to 3.3V MCUs. Architecture: Built on Winbond's proprietary NOR cell technology, the W25H02JVTBIM pairs a 32-bit shift register with an integrated command controller to manage page program (up to 256 bytes per page), sector/block/chip erase, and status register polling. The DTR mode samples data on both clock edges, doubling effective throughput at the same SCK frequency. The package pinout exposes /CS, SCK, IO0-IO3, /WP, /HOLD, VCC, and GND, enabling direct connection to modern MCU QSPI controllers. Typical applications: the W25H02JVTBIM is well suited to network router firmware storage, IoT gateway boot and data logging, set-top box / smart TV boot media, industrial HMI panel image storage, and automotive infotainment reference code where execute-in-place is required. Its 2 Gb density supports full firmware images plus room for OTA staging and asset storage. Design consideration: For systems upgrading from legacy SPI flash, verify that the host MCU's QSPI controller supports DTR mode to realize the full 50 MB/s throughput; otherwise the part still works in single-bit SPI mode. Ensure decoupling caps are placed as close as possible to VCC and GND, and follow Winbond's recommended PCB pad pattern for the 24-ball TFBGA.

RFQ Contact

W25H02JVTBIMG

W25H02JVTBIMG - 2Gb QSPI NOR Flash, 133MHz DTR, 24-TFBGA | Winbond

The Winbond W25H02JVTBIMG is a 2-Gbit (256M x 8) Serial NOR Flash memory device in the W25H family, housed in a 24-ball TFBGA (8x6 mm) package with industry-standard Quad-SPI and DTR (Double Transfer Rate) capability. It operates from a single 2.7V to 3.6V supply, supports clock rates up to 133 MHz in DTR mode, and delivers an equivalent throughput of 532 Mbit/s (66.5 MB/s) for execute-in-place (XIP) and high-speed code-storage applications. A Serial NOR Flash is a non-volatile memory that fetches code or data serially using a few signal wires instead of a wide parallel bus. Winbond's W25H family extends the popular W25Q Quad-SPI architecture with higher density and DTR support, enabling faster boot times and lower pin-count PCB designs. QSPI NOR Flash sits between raw parallel NOR (high speed, high pin count) and SPI NAND (lower cost, more complex controllers), making it ideal for code shadowing, firmware storage, and data logging in cost-sensitive embedded designs. Key features of the W25H02JVTBIMG include 2 Gbit density organized as 256 Mbytes, support for Standard SPI, Dual-SPI, Quad-SPI, QPI, and DTR modes, an OTP security area of 1024 bytes, individual block/sector protection, and JEDEC standard SFDP (Serial Flash Parameters Table) for parameter discovery. The device is rated for 100,000 erase cycles per sector minimum and 20-year data retention. It supports uniform 4 KB sector erase, 32 KB and 64 KB block erase, and full-chip erase, with status-register based protection for the top or bottom 4 KB block to host bootloader parameters. The W25H02JVTBIMG implements a low-power architecture with typical standby current under 10 µA and active read current around 25 mA at 104 MHz. Its DTR interface reads two bits per clock edge, effectively doubling throughput without raising the SPI clock frequency, which simplifies PCB signal-integrity design. The 'IMG' suffix (13th character 'G') indicates the part is manufactured using renewable energy per Winbond's published program; all specifications are identical to the W25H02JVTBIM variant. Typical applications include IoT edge devices, smart-home gateways, automotive infotainment and ADAS subsystems, industrial HMI panels, networking equipment boot ROM, and AI accelerator firmware storage. Compared with SPI NAND, NOR Flash provides faster random read latency (no ECC required) and byte-level XIP execution, at a higher cost-per-bit. When designing with this part, ensure that the host MCU's QSPI controller supports 3V flash and that the WP#/Hold# pins are properly terminated to avoid bus contention during in-system programming. Refer to the Winbond W25H02JV datasheet for SFDP parameters, AC timing, and recommended land-pattern geometry.

RFQ Contact

W25M02GWZEIG

W25M02GWZEIG - 2G-bit Serial SLC NAND Flash, 1.8V SPI | Winbond

The Winbond W25M02GWZEIG is a 2G-bit (2x1G-bit) Serial Multi-Chip Package (MCP) NAND flash memory built by stacking two W25N01GW SLC NAND die inside a standard 8-pin WSON 8x6 mm package. The device operates from a 1.8V supply and supports Standard SPI, Dual SPI, and Quad SPI interfaces with clock rates up to 104 MHz, including Continuous Read and Concurrent Read/Write operations. It exposes the standard JEDEC NAND command set with on-chip ECC and bad-block management, giving designers an SPI-friendly alternative to raw parallel NAND. As a member of the Winbond SpiFlash family, the part targets code-storage and data-logging footprints where byte-level random access and small-page SPI reads are preferable to a parallel NAND controller. A Serial NAND flash is a non-volatile memory that uses the SPI bus to expose the page-oriented programming and block-oriented erase operations of NAND, while adding an internal controller that hides the 2K-byte page and 128K-byte block geometry from the host MCU. The category hierarchy is: NAND flash -> non-volatile memory -> memory IC -> semiconductor. Compared with NOR flash, NAND offers higher density per die at lower cost-per-bit, but requires ECC and wear-leveling at the application layer; the W25M02GWZEIG adds internal ECC and configurable bad-block tables to reduce that host overhead. Key features of the W25M02GWZEIG include 2 Gbit total density (256 Mbytes), 2 Kbyte pages, 64 Kbyte spare/parameter blocks, dual-die addressing via die-select CS logic, 100K endurance cycles per block, and 10-year data retention. The 1.8V VCC range (1.7V to 1.95V) suits battery-powered IoT devices, and the wide operating temperature range of -40C to +85C covers industrial and consumer profiles. Quad SPI mode delivers up to 52 Mbyte/s read throughput, while continuous-read mode lets the host stream sequential pages without re-issuing the read command. Internal ECC is configurable up to 8-bit per 512-byte sector with hardware reporting through status registers. The W25M02GWZEIG is built on Winbond's 46 nm SLC NAND process, where each cell stores a single bit for high endurance and predictable retention, in contrast to MLC/TLC used in higher-density cards. The dual-die stack uses independent chip-enable logic so each die appears as a contiguous 1 Gbit logical array; this is transparent to standard SPI drivers that treat the device as a single 2 Gbit array. Compared to a discrete W25N01GW pair, the MCP reduces PCB area by ~50% and simplifies routing. Typical applications include IoT edge nodes storing firmware and telemetry, smart-home hubs, wearable health monitors, point-of-sale terminals, and industrial sensor loggers. The 1.8V supply also makes the part a natural fit for low-power MCUs such as the STM32L4 and Ambiq Apollo series. In designs that already use a small NOR for boot, the W25M02GWZEIG can sit beside it as the larger mass-storage bank without changing the host SPI bus topology. When designing with the W25M02GWZEIG, route the CS#, SCLK, IO0-IO3, and WP#/HOLD# signals as a 50-ohm impedance-controlled group and place a 100 nF decoupling capacitor within 3 mm of the VCC pad to suppress switching transients during Quad SPI reads. Confirm host SPI mode timing against the Winbond datasheet's tV and tSU figures and budget ECC bytes inside each 2K-byte page if your host driver reads raw pages. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond what is printed in the manufacturer datasheet, giving engineers a single reference for selecting, sourcing, and qualifying the W25M02GWZEIG.

RFQ Contact

W25M02GWZEIG-TR

W25M02GWZEIG-TR - 2G-bit Serial NAND Flash, 1.8V, SPI | Winbond

The Winbond W25M02GWZEIG-TR is a 2G-bit (2 x 1G-bit) serial Multi-Chip Package (MCP) flash memory built by stacking two individual 1G-bit W25N01GW SLC NAND die in a standard 8-pin WSON-8 (ZE) package. It operates from 1.7V to 1.95V supply and exposes a Serial Peripheral Interface (SPI) with single, dual, and quad I/O modes for high-throughput read access up to 104 MHz. According to the Winbond datasheet, the device supports continuous read across both die and concurrent operations between the two internal die for simultaneous read/write. A Serial NAND flash memory is a non-volatile storage IC that uses the SPI bus instead of a parallel interface, replacing legacy parallel NAND with a much smaller pin count while preserving page-based erase and program operations. Within the broader memory hierarchy, NAND flash sits below DRAM and NOR flash in random-access latency but offers far higher density per mm² and a much lower cost-per-bit, making it ideal for data logging, firmware shadowing, and multimedia buffering in embedded systems. The SpiFlash family from Winbond specifically targets cost-sensitive designs that need >128Mb of code or data storage. Key features include 2G-bit (256MB) density, 104 MHz maximum SPI clock, dual/quad SPI modes, page size of 2048 bytes + 64B spare area, block size of 128KB, and 100K program/erase cycles per block with 10-year data retention. The 8-WSON-8 8x6 mm package provides a compact footprint suitable for space-constrained PCB designs. The W25M02GW utilizes Winbond's proven 1G-bit SLC NAND die in a stacked-die MCP configuration. Internal die selection is automatic through a die-select command, and the host MCU sees a contiguous logical address space through extended addressing. ECC handling and bad-block management are typically implemented in the host controller or boot ROM for reliability. Typical applications include IoT edge devices, wearable electronics, automotive infotainment, point-of-sale terminals, industrial sensor data loggers, and 4G/LTE module firmware storage. The 1.8V operation makes it ideal for direct connection to low-power SoCs and PMICs without level shifters. When designing with this device, ensure the host controller implements software ECC (the W25M02GW is raw NAND without internal ECC engine) and reserves adequate RAM for the 2KB page buffer. Quad SPI mode requires all four data lines routed with length matching on the PCB for reliable high-speed reads.

RFQ Contact

W25N01GVZEIR

W25N01GVZEIR - 1Gbit SPI/Quad SLC NAND Flash | Winbond

The Winbond W25N01GVZEIR is a 1 Gbit (128 MByte) serial SLC NAND flash memory with SPI/Quad I/O interface, housed in an 8-WSON (8x6 mm) surface-mount package. Operating from 2.7 V to 3.6 V, it delivers a 104 MHz maximum clock rate with 7 ns access time, supporting standard SPI, Dual SPI, and Quad SPI modes for high-throughput code-shadowing and data-logging workloads. The device integrates a Continuous Read mode that streams sequential pages without command overhead, a 2 KB SRAM buffer for page read/program, on-die ECC, and a Bad Block Management Look-Up Table (BBM LUT) that transparently remaps failing blocks to reserved spares. A serial NAND flash such as the W25N01GVZEIR is a non-volatile memory IC that stores bits in NAND cell arrays but exposes them through a low-pin-count SPI bus rather than a parallel interface. SLC NAND stores one bit per cell, yielding 10x higher endurance and 10x lower bit error rate than MLC/TLC parts at the cost of density. The part belongs to the broader hierarchy NAND flash -> non-volatile memory -> memory IC -> semiconductor, sitting alongside SPI NOR flash and parallel NAND in modern embedded designs; SPI NAND typically wins where higher density per pin and lower cost-per-bit are required. Key features include industrial -40C to +85C operating range, 100k program/erase endurance cycles per block, 10-year data retention, hardware and software write protection, a 64-bit unique ID, and a JEDEC-standard SFDP (Serial Flash Discoverable Parameters) table that lets host controllers auto-configure the device. The 8-WSON package is halogen-free and RoHS compliant, with renewable-energy manufacturing indicated by the 'G' position-character. The W25N01GVZEIR uses a single 3 V supply and a 1-bit/2-bit/4-bit SPI bus to reduce host pin count versus parallel NAND. Its on-die ECC engine corrects up to 8-bit errors per 512-byte sector, freeing the host MCU from running software ECC and lowering CPU load during page reads. The integrated BBM LUT preserves the logical address space when bad blocks emerge during the device's lifetime, simplifying FTL design for raw-NAND Linux MTD and LittleFS deployments. Typical applications include IoT edge nodes requiring 1 Gbit of low-pin-count non-volatile storage, industrial sensor loggers, smart-home gateways, automotive infotainment boot + data partitions, consumer wearables storing firmware and telemetry, and embedded Linux systems booting from SPI NOR and using SPI NAND as a data partition. Compared with SPI NOR of equal density, SPI NAND delivers higher density per pin at a lower cost-per-bit while trading some random-access speed for sequential throughput. When designing, ensure the host controller supports the Winbond W25N-GV command set (0xEF manufacturer ID, 0xAA21 device ID) and that ECC is either disabled on the host or left to the on-die engine. Place a 1 uF decoupling capacitor within 5 mm of the VCC pin and route /CS through a dedicated GPIO so deep power-down (0xB9) can be asserted to drop standby current below 15 uA when the host sleeps. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact

W25N01GVZEIR-TR

W25N01GVZEIR-TR - 1Gb QSPI SLC NAND Flash | Winbond

The Winbond W25N01GVZEIR-TR is a 1 Gbit (128 MB) Serial SLC NAND Flash memory organized as 128M x 8, operating on a single 2.7V to 3.6V supply and housed in an 8-pin WSON (8x6 mm) package. It exposes a 1 Gbit capacity over a standard SPI/Quad-SPI bus at up to 104 MHz, with continuous-read and buffer-read modes for high-throughput code-shadowing workloads. A NAND Flash is a non-volatile memory that stores bits in floating-gate NAND strings, achieving higher density per cell than NOR at the cost of sequential-only programming and mandatory bad-block management. Compared with NOR Flash, NAND Flash offers lower cost-per-bit and faster erase/write cycles but cannot execute-in-place (XIP) and requires an embedded ECC engine and a Bad Block Management (BBM) lookup table - both of which W25N01GVZEIR-TR integrates on-die. Key features include SPI modes 0 and 3 clocking, Quad-SPI (x4 I/O) at 104 MHz delivering up to ~416 Mb/s read throughput (with the internal 2-Kbyte buffer in continuous-read mode), a hardware/software reset pin, write-enable latch, 4-KB sector erase, internal ECC with ECC-status reporting, Bad Block Management LUT, OTP security region, hardware and software write protection, and a -40C to +85C industrial operating range. The 8-WSON package includes an exposed thermal pad that ties to GND for board-level thermal dissipation. Architecturally, the die provides a 2-Kbyte data-buffer between the serial SPI/QSPI host interface and the 1 Gbit NAND array; the host streams commands across SPI (standard or quad) and the buffer transfers block data to/from the array, allowing the controller to suspend/resume reads without re-issuing page reads. This buffered architecture, combined with on-die ECC correction, enables reliable random-access patterns that older raw-NAND parts cannot deliver. Typical applications include IoT firmware storage, Linux kernel/rootfs storage for industrial gateways, data-logger file systems, smart-meter data retention, point-of-sale (POS) terminals, and consumer electronics where low-cost, high-density, non-volatile code/data storage is required and XIP is unnecessary. When designing, ensure the host driver implements the Winbond SPI-NAND command set, allocates a 2-Kbyte transfer buffer, and respects the ECC-status bits before declaring a page valid; failure to implement BBM-LUT will shorten useful endurance on parts with even one factory-marked bad block. This page synthesises distributor pricing, drop-in alternatives across Winbond and Macronix/ISSI families, and practical design notes not found in the raw manufacturer datasheet, helping hardware engineers shorten qualification cycles.

RFQ Contact

W25Q128FWPIG

W25Q128FWPIG - 128Mbit 1.8V Serial NOR Flash | Winbond

The Winbond W25Q128FWPIG is a 128 Mbit (16 Mbyte) 1.8 V Serial NOR Flash memory providing a compact storage solution for space-, pin-, and power-constrained systems. It supports standard SPI, Dual SPI, Quad SPI (QPI), and QPI modes, delivering up to 104 MHz clock rates for high-throughput code and data storage. The device is housed in an 8-pin WSON (6x5 mm) EP package with an exposed pad for thermal dissipation and ground integrity. A Serial NOR Flash is a non-volatile memory that connects to a host processor via a synchronous serial peripheral interface (SPI) rather than a wide parallel bus. Within the storage hierarchy, it sits above battery-backed SRAM and below high-density NAND flash: random-access latency is on the order of tens of nanoseconds, page-program time is measured in milliseconds, and the endurance is typically 100k erase cycles per sector. The 25Q series extends this with dual- and quad-I/O variants that multiply throughput by reusing existing pins. Key features include 128 Mbit density organised as 16 M x 8 bits, 4 KB uniform sectors combined into 32 KB and 64 KB blocks for flexible erase granularity, page-program of 256 bytes, and 100k erase/program endurance cycles with >20-year data retention. The device supports 1.7 V to 1.95 V single-supply operation, hardware and software write protection, a 64-bit unique ID, and three JEDEC-standard device identification bytes (9Fh) plus manufacturer/device IDs (Winbond EFh). Quad Enable (QE) bit enables continuous Quad SPI throughput. Internally, the W25Q128FW uses a NOR-array cell technology optimised for low-power read (typically <10 mA active, <1 uA standby), with on-chip SRAM buffers for page program and an integrated charge pump for program/erase. The state machine implements the full JEDEC 0x9F plus the Winbond-specific 0xAB (release power-down / read electronic ID) command set, and the standard 0x03 (read), 0x0B (fast read), 0x02 (page program), 0x20 (sector erase), 0xD8 (block erase), and 0xC7 (chip erase) commands. Typical applications include boot code and firmware storage in IoT edge nodes, asset-tracking and sensor data logging, wearable and portable consumer devices, OTA-updatable embedded firmware, automotive infotainment and instrument-cluster secondary bootloaders, point-of-sale terminals, and low-power wireless sensor modules. The 1.8 V supply matches directly to lithium-ion battery rails without an additional LDO. Design tip: when migrating between the W25Q128FW (1.8 V) and the 2.7-3.6 V W25Q128JV family, the JEDEC manufacturer ID (EFh) and the QE-bit location remain compatible, but the supply-voltage range does not - confirm the upstream regulator before substituting across voltage classes. This page synthesises real-time distributor pricing, pin-compatible drop-in alternatives, and design considerations not collected in a single place in the Winbond datasheet.

RFQ Contact

W25Q128JVFIQ

W25Q128JVFIQ - 128Mbit SPI/Quad SPI NOR Flash, 3V, 16-SOIC | Winbond

The Winbond W25Q128JVFIQ is a 128 Mbit (16 Mbyte) serial NOR Flash memory organized as 16,384 programmable pages of 256 bytes each, housed in a 16-pin SOIC (208 mil) package. It operates from a single 2.7 V to 3.6 V supply, supports standard SPI, Dual SPI, Quad SPI, and QPI modes, and clocks up to 133 MHz in single-I/O read, equivalent to 266 Mbit/s effective throughput when Quad I/O is engaged. The device replaces legacy EEPROM and parallel-NOR solutions with a low-pin-count 4-wire serial interface plus optional /WP and /HOLD pins. A serial NOR flash like the W25Q128JVFIQ is a non-volatile memory device that uses a synchronous serial peripheral interface (SPI) rather than a parallel address/data bus. It belongs to the broader category of NOR flash -> flash memory -> non-volatile memory IC, and serves as firmware storage in embedded systems. Uniform 4 KB sector erase, 32 KB and 64 KB block erase, and a 256-byte programmable page let designers optimize erase granularity versus endurance (typically 100K cycles per sector, 20-year data retention per Winbond). Key features of the W25Q128JVFIQ include dual/quad SPI with one 8-bit instruction clocked on a single I/O and 24/32-bit addressable space up to 128 Mb. The chip provides high read throughput (~6 ns access), continuous read mode with wrap-around, security registers (3 x 256-byte OTP), and individual block/sector locking via Status Register bits. A 64-bit Unique ID and JEDEC Manufacturer/Device ID (9Fh / EFh for Winbond 128 Mbit JV) simplify factory programming and traceability. Architecturally, the W25Q128JVFIQ uses Winbond's proprietary NOR cell array with an internal ECC engine on 8-byte boundaries (single-bit correction per ECC group), an SRAM page buffer for page program, and a charge-pump high-voltage generator for program/erase. The device also offers a QPI mode (quad peripheral interface) where all four I/O pins carry instruction/address/data, further boosting XIP throughput to ~532 Mbit/s peak. Typical applications include firmware/code shadowing for microcontrollers and SoCs, BIOS/storage for FPGA configuration bitstreams, IoT edge nodes storing OTA update images, automotive infotainment display back-up, and consumer electronics where small-footprint non-volatile code storage is required. Its 16-SOIC-300 footprint also routes easily to a wide range of MCU SPI masters. When designing with this device, ensure the host MCU SPI clock supports the configured 80 MHz to 133 MHz modes and that /CS, /WP (used as /IO2 in Quad), and /HOLD (used as /IO3 in Quad) are not left floating - unused Quad-I/O pins must be tied through a 10-100 kohm resistor to avoid noise-induced false commands. Also note that Quad-I/O fast-read commands (EBh, ECh) require the host to drive the mode-bit dummy cycle, which differs from single-I/O. This page synthesizes distributor pricing, JEDEC-compatible drop-in alternatives (including cross-brand second sources such as the GigaDevice GD25Q128), and design notes for both new designs and field-replacement scenarios that go beyond what the manufacturer datasheet alone provides.

RFQ Contact

W25Q128JVFIQ-TR

W25Q128JVFIQ-TR - 128Mbit SPI/Quad NOR Flash, 16-SOIC | Winbond

The Winbond W25Q128JVFIQ-TR is a 128M-bit (16MB) serial NOR flash memory in a 16-pin SOIC package, operating on a single 2.7V to 3.6V supply with active power consumption around 25 mA at 133 MHz quad-SPI clock. The -TR suffix denotes tape-and-reel packaging, and the device supports standard SPI, Dual SPI, Quad SPI, and QPI interfaces with a maximum clock rate of 133 MHz in quad-I/O mode for high-bandwidth code-storage and execute-in-place (XIP) workloads. A NOR flash memory is a non-volatile storage device that supports byte-level random read access and execute-in-place, meaning a microcontroller or SoC can fetch instructions directly from the flash array without copying them to RAM first. The W25Q family is built on Winbond's 3V SPI NOR process and offers a JEDEC-standard 25Q-series command set, making it interchangeable with other 25Q-compliant parts in firmware layers. It sits within the broader taxonomy of memory ICs -> non-volatile memory -> NOR flash -> SPI NOR flash, the most common code-storage medium for embedded MCUs, FPGAs, and boot ROMs. Key features of the W25Q128JVFIQ-TR include 128M-bit density organized as 16M bytes, uniform 4 KB sectors with 32 KB and 64 KB block erase options for flexible memory management, a 256-byte page programming buffer, and a Quad SPI mode that delivers up to 133 MHz clock with single-, dual-, and quad-I/O data transfer. The device also includes a 3-byte (default) and 4-byte address mode for >128Mbit addressing, security registers with One-Time-Programmable (OTP) lockable bits, and a configurable QE bit (Status Register bit 9) for enabling quad I/O at boot. The internal architecture combines a NOR memory array with a serial command decoder, an address counter, a 256-byte SRAM buffer, and the standard JEDEC 0x9F JEDEC-ID, manufacturer-ID, and device-ID registers. Continuous-read mode allows sequential read operations up to 133 MHz without command overhead, while the page-program and sector-/block-/chip-erase commands follow standard SFDP (Serial Flash Discoverable Parameters) discovery on JEDEC-compliant drivers. Typical applications include firmware storage for STM32, ESP32, NXP i.MX RT, and Renesas RA microcontrollers, BIOS/Boot ROM on FPGA configuration stages, data logging on IoT sensor nodes, and asset tracking on smart-metering endpoints. The 133 MHz quad-SPI throughput also makes it suitable for display frame buffering on small TFT panels where boot-time code fetch matters. When designing with the W25Q128JVFIQ-TR, ensure the SPI bus length is short (under 50 mm on standard FR-4) and that a 100 nF decoupling capacitor is placed within 5 mm of the VCC pin to limit switching noise. Note that quad-SPI XIP boot requires QE bit setup before the first quad command; firmware must program Status Register bit 9 once per reset to enable quad mode reliably.

RFQ Contact

W25Q40BVSNIG

W25Q40BVSNIG - 4Mb Serial NOR Flash SPI/Quad-SPI | Winbond

The Winbond W25Q40BVSNIG is a 4M-bit (512K x 8) serial NOR flash memory with Dual SPI and Quad SPI support, housed in an 8-pin SOIC-150 package. It operates from 2.7V to 3.6V supply, delivers up to 104 MHz clock rate in standard SPI mode (50 MHz for Quad SPI reads), and provides 4 Mbit (512 KB) of non-volatile storage organized as 65,536 pages of 256 bytes each or 2,048 sectors of 4 KB. A NOR flash memory is a non-volatile storage technology that retains data without power and supports byte-level random access and execute-in-place (XIP) operation. Within the memory hierarchy, NOR flash sits between SRAM (volatile, fast, expensive) and NAND flash (non-volatile, large block, slower random access), offering fast read access and reliable long-term data retention. NOR flash is commonly used for code storage, firmware boot, configuration parameters, and data logging in embedded systems. Key features include 100,000 erase/program cycles per sector endurance, 20-year data retention, low power consumption with 1 mA active read current at 50 MHz and 1 uA power-down current, and a uniform 4 KB sector erase granularity. The device supports JEDEC-standard 3-byte addressing with an option for 4-byte address mode, and offers hardware and software write protection via status register bits and a dedicated WP pin. The W25Q40BVSNIG uses a standard SPI interface with optional Dual-SPI (DIO/DOUT) and Quad-SPI (QIO/QOUT) modes that multiply throughput up to 4x compared to standard SPI. The integrated 256-byte page buffer and 4 KB sector erase make it suitable for both code shadowing to RAM and direct parameter storage. Security features include a 64-bit unique ID, three 256-byte security registers for OTP storage, and individual block locking. Typical applications include IoT device firmware storage, consumer electronics boot code, industrial sensor data logging, smart home devices, networking equipment configuration memory, and battery-powered portable electronics requiring small-footprint non-volatile storage. The 8-pin SOIC package allows easy hand-soldering and standard PCB reflow profiles. When designing with this device, ensure the SPI master supports the maximum 104 MHz clock in single I/O mode and observe the timing parameters in the Winbond datasheet. Use of Quad SPI mode requires firmware to issue the correct enable command (0x38) before reading, and the WP and HOLD pins must be properly biased to avoid spurious mode entry. This page synthesizes distributor pricing, drop-in alternatives (including the newer W25Q40EWSNIG revision), and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact

Subcategories

Products (35,000+)

VSC8484YJP - 10GbE Quad XAUI-to-Serial Transceiver BGA-324 | Microchip

VSC8490EV - Dual-Port 10G Ethernet Eval Board | Microchip

VSC8490YJU-17 - Dual-Port 10GbE PHY XFI/SFI to XAUI | Microchip

VSC8490YJU-17P Dual-Port 10GbE PHY | Microchip

VSC8502RD - 2-Port Gigabit Ethernet PHY | Microchip Technology

VSC8514EV - Quad-Port Gigabit Ethernet PHY | Microchip

VSC8531XMW-02 - GbE Cu PHY RGMII/RMII | Microchip 48-QFN

VSC8531XMW-05 - 1-Port GbE Cu PHY, RGMII/RMII, 48-QFN | Microchip

VSC8664EV - 4-Port Gigabit Ethernet PHY | Microchip Technology

VSP3200Y - 16-Bit 8MSPS CCD Signal Processor | TI

VSP3200Y-2K - 16-Bit 8MSPS CCD Signal Processor | Texas Instruments

VSP3200Y-2KG4 - 16-Bit 8MSPS CCD Signal Processor | TI

W24257AJ-20 - 32Kx8 20ns CMOS SRAM | Winbond DIP-28

W24512AKDV - 64Kx8 5V CMOS SRAM | Winbond

W25H02JVTBIM - 2Gb QSPI NOR Flash, 24-TFBGA | Winbond

W25H02JVTBIMG - 2Gb QSPI NOR Flash, 133MHz DTR, 24-TFBGA | Winbond

W25M02GWZEIG - 2G-bit Serial SLC NAND Flash, 1.8V SPI | Winbond

W25M02GWZEIG-TR - 2G-bit Serial NAND Flash, 1.8V, SPI | Winbond

W25N01GVZEIR - 1Gbit SPI/Quad SLC NAND Flash | Winbond

W25N01GVZEIR-TR - 1Gb QSPI SLC NAND Flash | Winbond

W25Q128FWPIG - 128Mbit 1.8V Serial NOR Flash | Winbond

W25Q128JVFIQ - 128Mbit SPI/Quad SPI NOR Flash, 3V, 16-SOIC | Winbond

W25Q128JVFIQ-TR - 128Mbit SPI/Quad NOR Flash, 16-SOIC | Winbond

W25Q40BVSNIG - 4Mb Serial NOR Flash SPI/Quad-SPI | Winbond